Escolar Documentos
Profissional Documentos
Cultura Documentos
LC-32M400M-BK/WH/RD
SERVICE MANUAL
No. S51Q1LC32M40M
CONTENTS
SAFETY PRECAUTION CHAPTER 6. TROUBLESHOOTING TABLE
IMPORTANT SERVICE SAFETY PRE- [1] TROUBLESHOOTING TABLE ......................6-1
CAUTION ............................................................i
PRECAUTIONS FOR USING LEAD-FREE CHAPTER 7. OVERALL WIRING/BLOCK DIAGRAM
SOLDER ............................................................ii [1] OVERALL WIRING DIAGRAM ......................7-1
[2] SYSTEM BLOCK DIAGRAM .........................7-2
OUTLINE
MAJOR SERVICE PARTS ................................ iii CHAPTER 8. PRINTED WIRING BOARD ASSEM-
BLIES
CHAPTER 1. SPECIFICATIONS [1] MAIN Unit ......................................................8-1
[1] SPECIFICATIONS ......................................... 1-1 [2] IR OPC Unit...................................................8-4
[3] TERMINAL Unit .............................................8-5
CHAPTER 2. OPERATION MANUAL
[1] OPERATION MANUAL .................................. 2-1 CHAPTER 9. SCHEMATIC DIAGRAM
[1] DESCRIPTION OF SCHEMATIC DIA-
CHAPTER 3. DIMENSIONS GRAM............................................................9-1
[1] DIMENSIONS ................................................ 3-1 [2] MAIN Unit ......................................................9-2
[3] IR OPC Unit.................................................9-13
CHAPTER 4. REMOVING OF MAJOR PARTS [4] TERMINAL Unit ...........................................9-14
[1] REMOVING OF MAJOR PARTS ................... 4-1
Parts Guide
CHAPTER 5. ADJUSTMENT
[1] ADJUSTMENT PROCEDURE ....................... 5-1
[2] USB Clone (Smart Loader) ............................ 5-6
[3] PUBLIC MODE SETTING PROCEDURE ........ 5-7
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
WARNING All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
1. For continued safety, no modification of any circuit should be only for the purpose of completing these checks.)
attempted.
Any reading of 0.74 Vrms (this corresponds to 0.5 mA rms AC.) or
2. Disconnect AC power before servicing. more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard)
Before returning the receiver to the user, perform the following
safety checks: DVM
3. Inspect all lead dress to make certain that leads are not pinched, AC SCALE
and check that hardware is not lodged between the chassis and
other metal parts in the receiver. 1.5k ohm
4. Inspect all protective devices such as non-metallic control knobs, 10W
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
0.15 µF
the following manner.
TEST PROBE
• Plug the AC cord directly into a 110-240 volt AC outlet.
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground. TO EXPOSED CONNECT TO
• Use an AC voltmeter having with 5000 ohm per volt, or higher, sen- METAL PARTS KNOWN EARTH
GROUND
sitivity or measure the AC voltage drop across the resistor.
• Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD colour television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
LC-32M400M-BK/WH/RD
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J φ0.3mm 250g (1roll)
ZHNDAi126500E BK J φ0.6mm 500g (1roll)
ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
ii
LC-32M400M-BK/WH/RD
LC32M400MBK
OUTLINE Service Manual
PWB UNIT
OTHER UNIT
SERVICE JIGS
iii
LC-32M400M-BK/WH/RD
CHAPTER 1. SPECIFICATIONS
LC32M400MBK
Service Manual
[1] SPECIFICATIONS
1–1
LC-32M400M-BK/WH/RD
CHAPTER 2. OPERATION MANUAL
LC32M400MBK
Service Manual
Part names
TV (Front)
Remote control sensor
OPC sensor
POWER indicator
Light off Power off
Lighted (Red) The TV is in standby mode.
Lighted (Green) The TV is on.
TV (Rear)
1 POWER (On/Off) button
2 MENU button
15 3 INPUT button
4 Channel up ( )/down ( ) buttons
5 Volume up ( )/down ( ) buttons
16 6 RS-232C terminal
7 INPUT 7 (PC) terminals*
8 Antenna input terminal
13 9 INPUT 4 terminals
6 14 1 10 INPUT 5 terminals
11 INPUT 6 terminals
2
7 12 AUDIO OUT terminal
3 13 INPUT 2 (HDMI) terminal
8 14 INPUT 1 (HDMI) terminal*
4 15 INPUT 3 (HDMI) terminal
16 USB terminal
5
9
10
11
12
* The INPUT 1 and INPUT 7 terminals can both use the same audio input terminal. However, the proper item must be
selected in the “PC Audio Select” menu.
• The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.
2–1
LC-32M400M-BK/WH/RD
2–2
LC-32M400M-BK/WH/RD
PC Control of the TV
• When a programme is set, the TV can be controlled from the PC using the RS-232C terminal.
The input signal (PC/video) can be selected, the volume can be adjusted and various other
adjustments and settings can be made, enabling automatic programmed playing.
• Attach an RS-232C cable cross-type (commercially available) to the Din/D-sub RS-232C for the
connections.
NOTE
• This operation system should be used by a person who is accustomed to using PCs.
Communication conditions
Set the RS-232C communications settings on the PC to match the communications conditions of
the TV. The communications settings of the TV are as follows:
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Communication procedure
Send the control commands from the PC via the RS-232C connector.
The TV operates according to the received command and sends a response message to the PC.
Do not send multiple commands at the same time. Wait until the PC receives the OK response before
sending the next command.
Command format
Eight ASCII codese CR Command 4-digits: Command. The text of four
C1 C2 C3 C4 P1 P2 P3 P4 characters.
Parameter 4-digits: Parameter 0 - 9, space, ?
Command 4-digits Parameter 4-digits Return code
Parameter
Input the parameter values, aligning left, and fill with space(s) for the remainder. (Be sure that four
values are input for the parameter.)
When the input parameter is not correct, "ERR" returns. (Refer to "Response code format".)
0
0 0 0 9
a 3 0
2–3
LC-32M400M-BK/WH/RD
SURROUND ON
SURROUND OFF
NOTE
• If an underbar (_) appears in the parameter column,
enter a space.
• If an asterisk (*) appears, enter a value in the range
indicated in brackets under CONTROL CONTENTS.
2–4
LC-32M400M-BK/WH/RD
CHAPTER 3. DIMENSIONS
LC32M400MBK
Service Manual
[1] DIMENSIONS
Unit: mm
453
300
792.2 99.2
699.2
170
539.5
393.8
300
575.9
333
86.3 113.3
241.6
3–1
LC-32M400M-BK/WH/RD
CHAPTER 4. REMOVING OF MAJOR PARTS
LC32M400MBK
Service Manual
Stand Unit 2
4–1
LC-32M400M-BK/WH/RD
2. Disconnect the connectors
1. Disconnect the connectors from the MAIN Unit, IR/OPC Unit, POWER, Unit, TERMINAL Unit, INVERTER Unit and LCD Panel Module [1].
LVDS
LVDS
PW
VA/VB VA/VB
1 1 1
P0 MA MB
SP MA MB
AC 1
RA
SP SP
RA
4–2
LC-32M400M-BK/WH/RD
3. Removing of the Side AV Cover Ass’y, Speaker-L/R and Bottom Bracket
1. Remove the 2 lock screws [1], and detach the Side AV Cover Ass’y [2].
2. Remove the 2 lock screws [3], 4 lock screws [4] and detach the Bottom Bracket [5].
3. Detach the Speaker L/R [6] and the Molt Plane [7].
Side AV
Cover Ass'y
2
1
4
Speaker-L 6 Speaker-R 6
3 Bottom Bracket 5
4–3
LC-32M400M-BK/WH/RD
4. Removing of the PWB Units
1. Detach the IR/OPC Unit [1].
2. Remove the 4 lock screws [2] and detach the TERMINAL Unit [3].
3. Remove the 4 lock screws [4] and detach the MAIN Unit [5].
4. Remove the 6 lock screws [6] and detach the POWER Unit [7].
6
POWER Unit 7 4
MAIN Unit 5
IR OPC Unit 1
TERMINAL Unit 3 2
4–4
LC-32M400M-BK/WH/RD
5. Removing of the LCD Panel Module
1. Remove the 4 lock screws [1] and detach VESA Angle [2].
2. Remove the 2 lock screws [3], 2 lock screws [4].
3. Detach the 6 pieces claws and detach the LCD Panel Module [5] from the Front Cabinet [6].
1 1
LCD Panel Module 5
Claw Claw
Claw Claw
4
3
Front Cabinet Ass'y 6
4–5
LC-32M400M-BK/WH/RD
CHAPTER 5. ADJUSTMENT
LC32M400MBK
Service Manual
2. Remote controller key operation and description of display in adjustment process mode.
1. key operation
* Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
5–1
LC-32M400M-BK/WH/RD
6) Let the process running & entering verification.
Verifying
Verified
7) Software is successfully installed when the following appears at the end of the process.
4. Signal adjustment
4.1. Signal check
Confirmation of signal from generator (setting to spec level)
5–2
LC-32M400M-BK/WH/RD
4.1.2 Component 15K 50Hz signal adjustment (COMP-SD)
[Terminal]
INPUT 6 COMPONENT
2 Auto adjustment Process Mode page 4 1) At the related page, move cursor to [COMP SD ADJ], press ENTER.
performance (COMP SD) 2) [OK] appears when finished.
[Terminal]
INPUT 6 COMPONENT
2 Auto adjustment Process Mode page 5 1) At the related page, move cursor to [COMP HD ADJ], press ENTER.
performance (COMP HD) 2) [OK] appears when finished.
[Terminal]
PC INPUT
2 Auto adjustment Process Mode page 6 1) At the related page, move cursor to [RGB ADJ], press ENTER.
performance (PC-RGB) 2) [OK] appears when finished.
5–3
LC-32M400M-BK/WH/RD
4.2. White balance adjustment
Point 1 9) Set the specified gradation for point 1. Set G of point 1 to the default value [(R1 x G
WBI10064 value of point 2/R2), with fractions rounded] and adjust RB to the reference value of
MG1G**** point 1.
MG1B****
MG1R**** 10)Adjusted value is writing at [command] MSET0003.
Write 11)Set the G of point Max. to the default value (4080 x G value of point 2/R2). Set the
MSET0003 R,B Max. value [Gmax-G value of point 2 + (R,B value of pint 2)].
[Adjustment Value]
✩Specification data by engineering dept is set as reference.
5–4
LC-32M400M-BK/WH/RD
5. Factory setting
AC power is plug off after shipment setting is done.
CAUTION: Do not plug on again after shipment setting is done. If do, please re-do the shipment setting. Do not off with remote control.
5–5
LC-32M400M-BK/WH/RD
[2] USB Clone (Smart Loader)
1. Description
The Smart Loader is a function implemented in the service software to easily replicate the user settings of one TV into another.
These settings include (but not restricted to): picture and audio, turning set-up, language and country selection, PIN, child locked programs etc.
Factory adjustments are not copied as they are different for every TV.
The Smart Loader makes possible the user data to be stored in a memory device connected to the USB terminal of the TV that is used as reference
and later load those data into other TVs by using their respective USB terminal.
2. How it works
---
i) SMLD Store
• To copy all related data from TV -> USB and put under a fixed filename "SHP_SMLD.bin" (8kB).
5–6
LC-32M400M-BK/WH/RD
[3] PUBLIC MODE SETTING PROCEDURE
1. How to start Public Mode
• There are the following two ways to get the public mode setup screen displayed.
1) Press the “TV/VIDEO” and “VOL (+)” keys on the set at once and turn on the power.
2) Get the password input screen displayed.
Procedure
• The input starts with the leftmost digit.
• Use the numeric keys [1] thru [9] and [10/0] keys on the remote controller.
The other keys are not acceptable.
• With a numeric-key input, “–” will change to “ “. The input position will move one digit to the right.
• With all the 3 digits entered, the password will be verified.
In the adjustment process mode, turn on “PUBLIC MODE”. Also press the “CH ( )” and “VOL (+)” keys on the set at once and turn on the power.
• Turn off “PUBLIC MODE” in the adjustment process mode. ( ) ← This way alone is not for quitting the setup screen, but for quitting the mode by
itself.
• Turn off the power with the “POWER” key. ( )
• Select “ENTER”.( )
• Move the cursor to “RESET” and press the “FLASHBACK” key. (Back to the normal mode screen) ( )
5–7
LC-32M400M-BK/WH/RD
4. Public Mode Menu
The guidance is not displayed onscreen.
Setup procedure
• To move the cursor up and down, use the “cursor UP/DOWN” key (remote controller) and “CH ( )/( )” key (remote controller and set).
• To change the settings, use the “cursor RIGHT/LEFT” key (remote controller) and “VOL (+)/(–)” key (remote controller and set).
• To save new settings, keep the cursor at “Enter” and use the “cursor RIGHT/LEFT” key (remote controller) and “VOL (+)/(–)” key (remote controller
and set).
Public mode
Power on fixed [Variable ]
Maximum volume [ 60]
Volume fixed [Variable ]
Volume fixed level [ 20]
RC button [Respond ]
Panel button [Respond ]
Menu button [Respond ]
On screen display [Yes ]
Blue Screen [No ]
Input mode start [Normal ]
Input mode fixed [Variable ]
232C Powon [Disable ]
RC path through [Off ]
Reset
Execute
5. On Setting Items
1. POWER ON FIXED
Selection Variable/Fixed
Default Variable
Explanation When set to “Fixed”, the power cannot be turned off with the power key on the remote control or main unit, and the image
reception state is kept (it does not enter the standby state).
The power can be turned off by shutting off power supply from AC.
Limit in setting • Power key on the main unit/remote control power supply key
• OFF timer/ON timer
Exception None
Remarks • Selection of “FIXED” assumes use of STB, etc.
• When set to “Variable”, if the main power switch is set to off, the power is turned off after a wait of 1 second.
(Push-push switch only)
• Display ON/OFF in the hotel menu is controlled by the adjustment process “HOTEL POWERFIX”.
• When the power button is operated, a caution is displayed (it times out in 5 seconds).
(For the caution, refer to the power on fixed message sheet.)
* The caution is not displayed when in the adjustment process, hotel menu, default setting, MCL operation and auto preset
(Ch search operation).
The OSD display including the menu and this caution have priority over all others.
When “OSD display” (described below) is set to “Variable”, this caution is displayed as a special case.
2. MAXIMUM VOLUME
5–8
LC-32M400M-BK/WH/RD
3. VOLUME FIXED
5. R/C BUTTON
Selection Selection between “Respond”, “Limited” and “No respond” (loop provide)
Default Respond
Explanation Acceptability of keys by remote control is limited or reception of keys can be prohibited.
Limit in setting 1) In “limited” setting, only power ON/OFF, sound volume , tuning and BACKLIGHT (brightness sensor) are
accepted.
2) In “No respond” setting, all the keys (including the power key) are not accepted.
Exception • Adjustment process, factory setting, inspection process and hotel only keys are valid irrespective of setting.
• All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
Remarks
6. PANEL BUTTON
7. MENU BUTTON
5–9
LC-32M400M-BK/WH/RD
8. ON SCREEN DISPLAY
9. BLUE SCREEN
12.232C POWON
5 – 10
LC-32M400M-BK/WH/RD
13.RC PATH THROUGH
5 – 11
LC-32M400M-BK/WH/RD
CHAPTER 6. TROUBLESHOOTING TABLE
LC32M400MBK
Service Manual
Is the AC cord connector tightly connected to the set? NO Reconnect the AC cord tightly and turn on the power again.
YES
Is the output voltage at pin (6), (7) and (8) of P9601 (13.0V line) NO Replace the power unit.
as specified?
YES
Are the wire harnesses and other cables properly connected in NO Reconnect the wire harnesses and other cables properly in the
the set? set.
YES
Is there the AC_DET and PNL_ON signal input at pins (11) and NO Check the AC_DET signal line PNL_ON signal line.
(12) of P9601?
YES
Are the DC/DC converter outputs and the output voltages along NO Check the DC/DC converters and the control lines. Replace
the control lines as specified? defective parts as required.
1) B5.6V (IC9603)
2) B1.26V (IC9604)
3) STB+3.3V (IC9606)
4) D2.6V (IC9607)
5) B5V (IC9608)
6) D3.3V (IC9609)
6–1
LC-32M400M-BK/WH/RD
Is there IF output from the tuner pin(10) of TU1101 as specified? NO Check TU1101 and its peripheral circuits.
YES
Is there VIF input at pin 56 & 57 of IC3301? NO Check the circuit between TU1101 & IC3301.
YES
Are there the signal outputs of IC3301? NO Check IC3301 and its peripheral circuit.
YES
Check LVDS cable, LCD controller (incl. panel) and their periph-
eral circuits.
Is INPUT 4 selected on the input select menu screen? NO Select INPUT 4 on the input select menu screen to pick up the
right input signal.
YES
Is there the video signal input at pin (35) of IC3301? NO Check the line between pin (4) of SC5201 and pin (35) of IC3301.
YES
Are there signal outputs of IC3301? NO Check IC3301 and its peripheral circuits.
YES
Check LVDS cable, LCD controller (incl. panel) and their periph-
eral circuits.
6–2
LC-32M400M-BK/WH/RD
Is INPUT 5 selected on the input select menu screen? NO Select INPUT 5 on the input select menu screen to pick up the
right input signal.
YES
Is there the video signal input at pin (33) of IC3301? NO Check the line between pin (6) of SC5201 and pin (33) of IC3301.
YES
Are there signal outputs of IC3301? NO Check IC3301 and its peripheral circuits.
YES
Check LVDS cable, LCD controller (incl. panel) and their periph-
eral circuits.
Is INPUT 4 selected on the input select menu screen? NO Select INPUT 4 on the input select menu screen to pick up the
right input signal.
YES
Are there the following signal inputs at the input terminals of NO <S-video signal>
IC3301? Check the line between pins (1), (2) of SC5201 and pins (30)/(29)
of IC3301.
<S-video signal>
Are there the Y and C signal inputs at pins (30) and (29), respec-
tively?
YES
Are there signal outputs of IC3301? NO Check IC3301 and its peripheral circuits.
YES
Check LCD controller (incl. panel) and their peripheral circuits.
6–3
LC-32M400M-BK/WH/RD
Is INPUT 6 selected on the input select menu screen? NO Select INPUT 6 on the input select menu screen to pick up the
right input signal.
YES
Are there the Y, Pb and Pr signal inputs at pins (15), (13) and NO Check the line between pins (15)/(13)/(12) of SC5201 and pins
(17) of IC3301 respectively? (15)/(13)/(17) of IC3301.
YES
Is input waveform of IC3301 normal? NO Check IC3301 and its peripheral circuits.
Y=(15) pin, Pb=(13) pin, Pr=(17) pin
YES
Check LVDS cable, LCD controller (incl. panel) and their periph-
eral circuits.
Is INPUT 1/INPUT 2/INPUT 3 selected on the menu screen? NO Select INPUT 1/INPUT 2/INPUT 3 on the input select menu
screen to pick up the right signal input.
YES
Are there the signal input from HDMI connector to the following NO Check IC1551 and their peripheral circuits.
input terminals of IC1551?
YES
Are there signal outputs from IC1551 to IC3301? NO Check peripheral circuits between IC1551 and IC3301.
YES
Are there signal outputs of IC3301? NO Check IC3301 and its peripheral circuits.
YES
Check LVDS cable, LCD controller (incl. panel) and their periph-
eral circuits.
6–4
LC-32M400M-BK/WH/RD
Is the IF output from the tuner pin (10) of TU1101 as specified? NO Check TU1101 and its peripheral circuits.
YES
Is there the I2S signal input at pins (180), (181) of IC3301? NO Check IC3301 and its peripheral circuits.
YES
Is there L-ch audio signal input at pin(3) of IC2701? NO Check connection between IC3301 and IC2701 and its
Is there R-ch audio signal input at pin(7) of IC2701? peripheral circuits.
YES
Is the L-ch audio signal output at pin(27), (28), (29), (30) and (31) of NO Check IC2701 and its peripheral circuits.
IC2701 normal?
Is the R-ch audio signal output at pin(11), (12), (13), (14) and (15) of
IC2701 normal?
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of NO Check circuit between IC2701 & P2701.
P2701 normal?
YES
Check speakers and their peripheral circuits.
6–5
LC-32M400M-BK/WH/RD
YES
Is there the I2S signal input at pin (180), (181) of IC3301? NO Check IC3301 and its peripheral circuits.
YES
Is there L-ch audio signal input at pin(3) of IC2701? NO Check connection between IC3301 and IC2701 and its periph-
Is there R-ch audio signal input at pin(7) of IC2701? eral circuits.
YES
Is the L-ch audio signal output at pin(27), (28), (29), (30) and (31) NO Check IC2701 and its peripheral circuits.
of IC2701 normal?
Is the R-ch audio signal output at pin(11), (12), (13), (14) and (15)
of IC2701 normal?
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of NO Check circuit between IC2701 & P2701.
P2701 normal?
YES
Check speakers and their peripheral circuits.
6–6
LC-32M400M-BK/WH/RD
Does the HDMI image appear onscreen? NO Refer to “<INPUT 1> in No external input video onscreen
(HDMI)”.
YES
No audio output from <INPUT 1>, <INPUT 2>, <INPUT 3>. NO Check the EDID.
YES
Are waveforms input in to the pins of IC3301 normally and I2S out- NO Check peripheral circuits between IC3301 and IC1551.
put from the pins (255), (256) normally?
YES
Is there L-ch audio signal input at pin(3) of IC2701? NO Check connection between IC3301 and IC2701 and its periph-
Is there R-ch audio signal input at pin(7) of IC2701? eral circuits.
YES
Is the L-ch audio signal output at pin(27), (28), (29), (30) and (31) NO Check IC2701 and its peripheral circuits.
of IC2701 normal?
Is the R-ch audio signal output at pin(11), (12), (13), (14) and (15)
of IC2701 normal?
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of NO Check circuit between IC2701 & P2701.
P2701 normal?
YES
Check speakers and their peripheral circuits.
6–7
LC-32M400M-BK/WH/RD
YES
Is there the L-ch audio signal input from pin (2) of external input
terminal J506 (HDMI AUDIO IN) to pin (70) of IC3301?
Is there the R-ch audio signal input from pin (3) of external input
terminal J506 (HDMI AUDIO IN) to pin (71) of IC3301?
YES
Are I2S signal output from the pins (180), (181) of IC3301 nor- NO Check peripheral circuits of IC3301.
mally?
YES
Is there L-ch audio signal input at pin(3) of IC2701? NO Check connection between IC3301 and IC2701 and its periph-
Is there R-ch audio signal input at pin(7) of IC2701? eral circuits.
YES
Is the L-ch audio signal output at pin(27), (28), (29), (30) and (31) NO Check IC2701 and its peripheral circuits.
of IC2701 normal?
Is the R-ch audio signal output at pin(11), (12), (13), (14) and (15)
of IC2701 normal?
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of NO Check circuit between IC2701 & P2701.
P2701 normal?
YES
Check speakers and their peripheral circuits.
6–8
LC-32M400M-BK/WH/RD
No PC audio output
YES
Pin (2) of J506: Is L-ch input into the pin (70) of IC3301?
Pin (3) of J506: Is R-ch input into the pin (71) of IC3301?
YES
Are I2S signal output from the pins (180), (181) of IC3301 normally? NO Check peripheral circuits of IC3301.
YES
Is there L-ch audio signal input at pin(3) of IC2701? NO Check connection between IC3301 and IC2701 and its
Is there R-ch audio signal input at pin(7) of IC2701? peripheral circuits.
YES
Is the L-ch audio signal output at pin(27), (28), (29), (30) and (31) of NO Check IC2701 and its peripheral circuits.
IC2701 normal?
Is the R-ch audio signal output at pin(11), (12), (13), (14) and (15) of
IC2701 normal?
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of NO Check circuit between IC2701 & P2701.
P2701 normal?
YES
Check speakers and their peripheral circuits.
6–9
LC-32M400M-BK/WH/RD
- MEMO -
6 – 10
LC-32M400M-BK/WH/RD
CHAPTER 7. OVERALL WIRING/BLOCK DIAGRAM
LC32M400MBK
Service Manual
7–1
LC-32M400M-BK/WH/RD
[2] SYSTEM BLOCK DIAGRAM
㪣㪜㪛 㪠㪩㪶㪦㪧㪚
㪣㪜㪛 㪦㪧㪚 㪠㪩㩷㪩㪼㪺㫀㪼㫍㪼㫉
㪛㪈㪇㪊㪆㪈㪇㪉 㪠㪚㪈㪇㪈 㪩㪤㪚㪈㪇㪈
㪩㪘㩿㪎㪀
㪺㫃㫂㩿㪉㪀
㪟㪧㪛㪇㪶㪠
㪻㪸㫋㪸㩿㪋㪀
㪻㪸㫋㪸㩿㪋㪀
㪺㫃㫂㩿㪉㪀
㪠㪉㪚㩿㪟㪛㪤㪠
㪠㪉㪚㩿㪟㪛㪤㪠
㪻㪸㫋㪸㩿㪋㪀
㪟㪧㪛㪈㪶㪠
㪟㪧㪛㪉㪶㪠
㪠㪉㪚㩿㪟㪛㪤㪠
㪺㫃㫂㩿㪉㪀
㪢㪜㪰
㪠㪝
㪠㪉㪚 㪧㪦㪮㩷㪪㪮
㪜㪜㪧㪩㪦㪤 㪜㪜㪧㪩㪦㪤 㪜㪜㪧㪩㪦㪤 㪪㪐㪇㪎
㪠㪚㪈㪌㪇㪈 㪠㪚㪈㪌㪇㪉 㪠㪚㪈㪌㪇㪊 㪠㪝㩷㪘㪤㪧 㪫㪜㪤㪧㩷㪪㪜㪥㪪㪦㪩
㪭㪟㪠㪪㪉㪋㪚㪪㪇㪉㪡㪄 㪭㪟㪠㪪㪉㪋㪚㪪㪇㪉㪡㪄 㪭㪟㪠㪪㪉㪋㪚㪪㪇㪉㪡㪄 㪫㪟㪊㪊㪇㪈
㪟㪧㪛㪇㪶㪠㪥㪃 㪤㪘㪠㪥㩷㪪㪮
㪈㪰 㪈㪰 㪈㪰 㪩㪟㪄㪟㪯㪘㪇㪋㪎㪮㪡㪨㪱㪰
㪟㪧㪛㪈㪶㪠㪥㪃
㪟㪛㪤㪠㩷㩷㪪㪮 㪟㪧㪛㪉㪶㪠㪥 㵘㵘㵘㵘 㪈 㪚㪦㪥㪫㪩㪦㪣㩷㪪㪮
㪠㪚㪈㪌㪌㪈 㪭㪠㪝 㪪㪠㪝 㪪㪐㪇㪈㪄㪪㪐㪇㪌
㪙㪬㪈㪍㪇㪉㪏㪢 㪙㩷㫋㫆㩷㪙
㪪㪘㪮㩷㪝㫀㫃㫋㪼㫉 㪪㪘㪮㩷㪝㫀㫃㫋㪼㫉 㪢㪜㪰㪉
㪪㪚㪌㪉㪇㪉
㪩㩷㪣㪜㪛
䌇㩷㪣㪜㪛
㪈㪌㫇㫀㫅
㪠㪩㪜㪤
㪪㪠㪝㪂
㪪㪠㪝㪄
㪭㪠㪝㪂
㪭㪠㪝㪄
㪮㪧㪶㪚㪫㪩㪣㩿㪫㫉㫀㪸㫃㩷㫆㫅㫃㫐㪀
㪦㪧㪚
㪠㪩 㪠㪥㪧㪬㪫㪋㪶㪰㪃㪧㪹㪃㪧㫉
㪜㪜㪧㪩㪦㪤 㪟㪛㪤㪠㩷㪠㪥㪈 㪟㪦㪫㪧㪣㪬㪞 㪭㪠㪝㩷㪠㪥 㪪㪠㪝㩷㪠㪥 㪪㪘㪩㩿㪊㪀 㪘㪛㪚㩿㪋㪀 㪘㪛㩿㪇㪀 㪪㪘㪩㩿㪇㪀 㪪㪘㪩㩿㪈㪀 㪚㪦㪤㪧㪶㪇
㪠㫅㫋㪼㫉㪽㪸㪺㪼 㪚㪦㪤㪧㪦㪥㪜㪥㪫㩷㪈㩷㪠㪥
㪠㪚㪌㪇㪏 㪟㪛㪤㪠㩷㪛㪛㪚㪈 㪘㪬㪛㪠㪦㩷㪠㪥
㪭㪟㪠㪪㪉㪋㪚㪪㪇㪉㪡㪄㪈㪰 㪡㪌㪌㪇㪊
㪠㪥㪧㪬㪫㪋㩷㪣㪆㪩
㪣㪆㪩㩷㪠㪥㪈
㪣㪠㪥㪜㪶㪦㪬㪫㩷㪘㪤㪧 㪤㪦㪥㪠㪫㪦㪩㩷㪣㪆㪩㩷㪦㪬㪫
㪧㪚㩷㩷㪛㪪㪬㪙㩷㪈㪌㫇㫀㫅 㪤㪦㪥㪠㪫㪦㪩 㪣㪠㪥㪜㩷㪦㪬㪫㪇㩷㪣㪆㪩 㪡㪌㪌㪇㪋
㪧㪚㩿㪩㪞㪙㪀 㪠㪚㪉㪎㪇㪉
㪪㪚㪌㪇㪉 㪦㪬㪫㪶㪇
㪭㪟㪠㪛㪩㪭㪍㪈㪉㪂㪂㪄㪠㪰
㪪㪘㪥㪡㪠㩷㩿㪛㪪㪄㪇㪈㪙㪄㪇㪈㪤㪀 㪟㪛 㪧㪚㩷㪛㪛㪚
㪭㪛
㪠㪥㪧㪬㪫㪎 㪨㪚㪥㪚㪮㪘㪐㪏㪍㪮㪡㪨㪱㪰 㪫㪜㪩㪤㪠㪥㪘㪣
㪬㪥㪠㪫
㪟㪛㪤㪠㪆㪧㪚㩷㪣㪆㪩
㪠㪥㪧㪬㪫㪌㩷㪚㪭㪙㪪
㪡㩷㪌㪇㪍 㪣㪆㪩㩷㪠㪥㪇 㪚㪭㪙㪪㪈
㪨㪡㪘㪢㪡㪘㪇㪉㪋㪮㪡㪱㪱
㪠㪥㪧㪬㪫㪌㩷㪣㪆㪩
㪠㪥㪧㪬㪫㪈㪆 㪣㪆㪩㩷㪠㪥㪉
㪠㪥㪧㪬㪫㪎
㪚㪭㪙㪪㪈㩷㪠㪥
㪠㪥㪧㪬㪫㪍㩷㪚㪭㪙㪪 㪚㪭㪙㪪㪉㩷㪠㪥
㪯㪫㪘㪣㩿㪈㪋㪅㪊㪈㪏㪤㪟㫑㪀 㪯㪠㪥㪆㪯㪦 㪚㪭㪙㪪㪉 㪡㪌㪌㪇㪉
㪯㪊㪊㪇㪈 㪙㩷㫋㫆㩷㪙
㪩㪚㪩㪪㪚㪘㪉㪋㪐㪮㪡㪨㪱㪰 㪪㪚㪌㪉㪇㪈
㪠㪥㪧㪬㪫㪍㩷㪣㪆㪩 㪈㪌㫇㫀㫅
㪠㪉㪚㩷㪘㪛㪛㪩㪜㪪㪪䋺㪘㪏
㪣㪆㪩㩷㪠㪥㪊
㪜㪜㪧㪩㪦㪤㩿㪟㪛㪚㪧㪀
㪠㪉㪚
㪠㪚㪏㪋㪇㪊 㪠㪥㪧㪬㪫㪌㩷㪪㪰㪆㪪㪚 㪪㪰㪆㪚㩷㪠㪥
㪩㪟㪄㪠㪯㪛㪈㪈㪇㪮㪡㪨㪱㪰 㪰㪆㪚㪇 㪡㪌㪌㪇㪈
㪠㪥㪧㪬㪫㪌㪶㪪㩷㪻㪼㫋㪼㪺㫋
㪠㪉㪚㩷㪘㪛㪛㪩㪜㪪㪪䋺㪘㪋
㪜㪜㪧㪩㪦㪤㩿㪛㪘㪫㪘㪀 㪠㪉
㪠㪚㪏㪋㪇㪉
㪭㪟㪠㪩㪉㪋㪇㪍㪋㪘㪪㪄㪈㪰
㪍㪋㪢㪹㫀㫋
㪤㪪㪫㪐㪘㪏㪏㪋㪡㪣㩿㪮㪯㪞㪘㩷㪤㪦㪛㪜㪣㪀 㪙㪣㪶㪦㪥
AC
IN
㪏㪄㪹㫀㫋㩷㪮㪯㪞㪘㩷㪘㫅㪸㫃㫆㪾 㪦㪝㪣
㪩㪼㪽㩷㪥㫆㪅㪠㪚㪊㪊㪇㪈 㪣㪘㪤㪧㩷㪜㪩㪩
㪩㪟㪄㪠㪯㪛㪇㪈㪏㪮㪡㪱㪱
㪘㪚㪶㪛㪜㪫
㪧㪪㪶㪦㪥 㪧㪦㪮㪜㪩
㪬㪥㪠㪫
㪎㪅㪌㹢㪈㪊㪅㪌㪭
㪪㪫㪙
㪂㪌㪭
㪪㪫㪙
㪂㪊㪅㪊㪭
㪛㪉㪅㪍㪭
㪙㪌㪭
㪛㪊㪅㪊㪭
㪈㪅㪉㪍㪭
㪨㪚㪥㪚㪮㪙㪇㪈㪐㪮㪡㪨㪱㪰
㪧㪥㪣㪈㪉㪭
㪛㪘㪫㪘㩷㪘㩿㪈㪇㪀 㪣㪮
㪛㪘㪫㪘㩷㪘㩿㪈㪇㪀 㪧㪘㪥㪜㪣
㪣㪭㪛㪪㩷㩿㪏㩷㪙㫀㫋㪀 㪚㪣㪢㩷㪘㩿㪉㪀 㪪㪚㪉㪍㪇㪈 㪚㪣㪢㩷㪘㩿㪉㪀 㪊㪉㩹㪮㪯㪞㪘
㪋㪈㫇㫀㫅
㪌㪇㪆㪍㪇㪟㫑
㪠㪥㪭㪜㪩㪫㪜㪩
㪬㪘㪩㪫 㪬㪪㪙㩷㪠㪝 㪛㪩㪘㪤㩷㪠㪝 㪘㪬㪛㪠㪦㪶㪦㪬㪫 㪪㪧㪠㩷㪠㪝 㪣㪢㪊㪈㪌㪫㪊㪣㪘㪎㪎㩿㪫㪼㫄㫇㫆㫉㪸 㪬㪥㪠㪫
㫉㫐㪀
㪟㪆㪮㩷㪩㪜㪪㪜㪫
㪪㪧㪠
㪪㪧㩷㪤㪬㪫㪜
㪪㪧㪶㪣
㪪㪧㪶㪩
IR 㪪㪧㪠㩷㪝㪣㪘㪪㪟
㪩㪜㪪㪜㪫 㪛㪛㪩㪉㩿㪈㪉㪏㪤㪹㪀 㪪㪧㪠㩷㪝㪣㪘㪪㪟 㪮㪩㪠㪫㪜
㪠㪚㪊㪊㪇㪉 㪠㪚㪊㪌㪇㪈 㪠㪚㪏㪋㪇㪈 㪚㪟㪜㪢㪜㪩㩷㪣㪘㪥㪛
㵘㵘㵘 㪩㪟㪄㪠㪯㪚㪐㪐㪋㪮㪡㪨㪱㪨 㪩㪟㪄
㪭㪟㪠㪧㪪㪫㪏㪋㪉㪐㪬㪄㪈㪰
㪠㪚㪌㪇㪊 㪩㪪㪉㪊㪉㪚㩷㪙㫌㪽㪽㪼㫉 㪠㪯㪛㪊㪍㪏㪮㪡㪨㪱㪨
㪭㪟㪠㪘㪟㪫㪈㪞㪇㪏㪮㪄 㪠㪚㪌㪇㪈 㪋㪤㪙
㪈㪰 㪭㪟㪠㪤㪊㪉㪉㪈㪜㪠㪧㪄㪈㪰
㪬㪪㪙㩷㪌㪭
㪘㪬㪛㪠㪦㩷㪘㪤㪧
㪠㪚㪌㪇㪐
㪠㪚㪉㪎㪇㪈
㪤㪘㪠㪥 IR PASS
㪭㪟㪠㪪㪈㪎㪇㪙㪌㪇㪬㪄㪈㪰
㪭㪟㪠㪰㪛㪘㪈㪋㪏㪨㪱㪄㪈㪰
㪪㪧㪶㪣
㪪㪧㪶㪩
THROUGH
PIN 9
㪩㪪㪄㪉㪊㪉㪚 㪬㪪㪙
㪪㪚㪌㪇㪈 㪡㪌㪇㪉 㪪㪧
㪪㪘㪥㪡㪠㩷㩿㪛㪧㪄㪇㪊㪄㪇㪈㪤㪱㪈㪀 㪨㪪㪦㪚㪱㪘㪉㪏㪋㪮㪡㪨㪱 㪧㪉㪎㪇㪈
㪨㪧㪣㪞㪥㪘㪐㪍㪈㪮㪡㪱㪱㪰
㪪㪧㪶㪣
㪪㪧㪶㪩
㵘㵘㵘㵘㵘㵘㵘
㪪㪧 㪣 㪪㪧 㪩
㪏㱅㩷㪌㪮 㪏㱅㪌㪮
7–2
LC-32M400M-BK/WH/RD
CHAPTER 8. PRINTED WIRING BOARD ASSEMBLIES
LC32M400MBK
Service Manual
MAIN Unit
(Side-A)
8–1
LC-32M400M-BK/WH/RD
MAIN Unit
(Chip Parts Side-A)
8–2
LC-32M400M-BK/WH/RD
MAIN Unit
(Side-B)
8–3
LC-32M400M-BK/WH/RD
[2] IR OPC Unit
8–4
LC-32M400M-BK/WH/RD
[3] TERMINAL Unit
Terminal Unit
8–5
LC-32M400M-BK/WH/RD
Terminal Unit
(Chip Parts)
8–6
LC-32M400M-BK/WH/RD
CHAPTER 9. SCHEMATIC DIAGRAM
LC32M400MBK
Service Manual
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
9–1
LC-32M400M-BK/WH/RD
[2] MAIN Unit
• MAIN Unit-1/11
9–2
LC-32M400M-BK/WH/RD
• MAIN Unit-2/11
9–3
LC-32M400M-BK/WH/RD
• MAIN Unit-3/11
9–4
LC-32M400M-BK/WH/RD
• MAIN Unit-4/11
9–5
LC-32M400M-BK/WH/RD
• MAIN Unit-5/11
9–6
LC-32M400M-BK/WH/RD
• MAIN Unit-6/11
9–7
LC-32M400M-BK/WH/RD
• MAIN Unit-7/11
9–8
LC-32M400M-BK/WH/RD
• MAIN Unit-8/11
9–9
LC-32M400M-BK/WH/RD
• MAIN Unit-9/11
9 – 10
LC-32M400M-BK/WH/RD
• MAIN Unit-10/11
9 – 11
LC-32M400M-BK/WH/RD
• MAIN Unit-11/11
9 – 12
LC-32M400M-BK/WH/RD
[3] IR OPC Unit
9 – 13
LC-32M400M-BK/WH/RD
[4] TERMINAL Unit
• TERMINAL Unit 1
9 – 14
LC-32M400M-BK/WH/RD
• TERMINAL Unit 2
9 – 15
LC-32M400M-BK/WH/RD
• TERMINAL Unit 3
9 – 16
PartsGuide
LC-32M400M-BK/WH/RD
PARTS GUIDE
No. S51Q1LC32M40M
CONTENTS
[1] PRINTED WIRING BOARD [6] CABINET AND MECHANICAL
ASSEMBLIES PARTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
2
LC-32M400M-BK/WH/RD
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
3
LC-32M400M-BK/WH/RD
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
4
LC-32M400M-BK/WH/RD
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
5
LC-32M400M-BK/WH/RD
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
6
LC-32M400M-BK/WH/RD
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
7
LC-32M400M-BK/WH/RD
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
8
LC-32M400M-BK/WH/RD
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
9
LC-32M400M-BK/WH/RD
[6] CABINET AND MECHANICAL PARTS
H
1
A
IR/OPC Unit
19
1-7
9
G 13
B
1-6 19
1-1
1-5 B
1-2
9
1-3 1-8
1-7
B 2 24
1-6 22
16
2-1 23
24
B
18 A
M 2-6
6
A
17
2-2 2-6
1-4
24
26
3 2-4
14 2-7
J
3-2 2-5
2-4
25 2-7
20
4
3-1 12 7
2-3 2-5
E H A
I
MAIN Unit D 24
25
F
TERMINAL Unit
I
G 11
POWER Unit
25
LCD Panel Module Unit 15
20
5
29
20 L 15 K
5
J 27
E
F 10
7
L
K
D
8
21
24 8
28 M
10
LC-32M400M-BK/WH/RD
11
LC-32M400M-BK/WH/RD
[7] SUPPLIED ACCESSORIES
12
LC-32M400M-BK/WH/RD
[8] PACKING PARTS (NOT REPLACEMENT ITEM)
S5
S6
X2
X1
X3
X5
X7
S3
S3
X4
S2
S10
S4
S4
S7
S8
S9
S1
13
LC-32M400M-BK/WH/RD
NO. PARTS CODE PRICE NEW PART
DESCRIPTION
RANK MARK DELIVERY
14
LC-32M400M-BK/WH/RD
LC-32M400M-BK/WH/RD
SHARP CORPORATION
AV Systems Group
May. 2011 CS Promotion Center
SY. KY Yaita, Tochigi, 329-2193, Japan