Escolar Documentos
Profissional Documentos
Cultura Documentos
SEMESTER 2 2017/2018
MINI PROJECT
ID NUMBER : CE097988
SECTION : 02
Structure View
Perspective 3D
27/01/18 18:13
27/01/18 18:13
Loads - Cases
Loads - Values
27/01/18 18:13
27/01/18 18:13
27/01/18 18:14
Member Verification
STEEL DESIGN
----------------------------------------------------------------------------------------------------------------------------- -----------
CODE: BS-EN 1993-1:2005/NA:2008/A1:2014, Eurocode 3: Design of steel structures.
ANALYSIS TYPE: Member Verification
----------------------------------------------------------------------------------------------------------------------------- -----------
CODE GROUP:
MEMBER: 7 Beam_7 POINT: 3 COORDINATE: x = 0.25 L = 1.00 m
----------------------------------------------------------------------------------------------------------------------------------------
LOADS:
Governing Load Case: 3 COMB1 1*1.35+2*1.50
----------------------------------------------------------------------------------------------------------------------------- -----------
MATERIAL:
S275 ( S275 ) fy = 275.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------
LIMIT DISPLACEMENTS
Connection Verification
GENERAL
Connection no.: 2
Structure node: 6
Structure bars: 7, 8
GEOMETRY
Date : 27/01/18 Page : 7
Autodesk Robot Structural Analysis Professional 2018
Author: MOHD SAUFI BIN ALI File: Mini Project Steel Mohd Saufi.rtd
Address: Project: Mini Project Steel Mohd Saufi
LEFT SIDE
BEAM
Section: UB 254x102x28
Bar no.: 7
Material: S275
RIGHT SIDE
BEAM
Section: UB 254x102x28
Bar no.: 8
Material: S275
BOLTS
The shear plane passes through the UNTHREADED portion of the bolt.
h1 = 52 [mm] Distance between first bolt and upper edge of front plate
PLATE
hpr = 279 [mm] Plate height
FILLET WELDS
aw = 5 [mm] Web weld
MATERIAL FACTORS
M0 = 1.00 Partial safety factor [2.2]
LOADS
Ultimate limit state
RESULTS
Date : 27/01/18 Page : 9
Autodesk Robot Structural Analysis Professional 2018
Author: MOHD SAUFI BIN ALI File: Mini Project Steel Mohd Saufi.rtd
Address: Project: Mini Project Steel Mohd Saufi
BEAM RESISTANCES
TENSION
SHEAR
leff,cp – Effective length for a single bolt in the circular failure mode
leff,nc – Effective length for a single bolt in the non-circular failure mode
leff,cp,g – Effective length for a group of bolts in the circular failure mode
leff,nc,g – Effective length for a group of bolts in the non-circular failure mode
Ft,ep,Rd(2 + 1) - ∑11 Ftj,Rd = 226.08 - 113.04 113.04 Front plate - tension - group
Ft,wb,Rd(2 + 1) - ∑11 Ftj,Rd = 211.42 - 113.04 98.38 Beam web - tension - group
Ft,ep,Rd(3 + 2) - ∑22 Ftj,Rd = 178.75 - 98.38 80.37 Front plate - tension - group
Ft,wb,Rd(3 + 2) - ∑22 Ftj,Rd = 138.60 - 98.38 40.22 Beam web - tension - group
Ft,ep,Rd(3 + 2 + 1) - ∑21 Ftj,Rd = 316.82 - 211.42 105.40 Front plate - tension - group
Ft,wb,Rd(3 + 2 + 1) - ∑21 Ftj,Rd = 280.72 - 211.42 69.30 Beam web - tension - group
Ft,ep,Rd(4 + 3) - ∑33 Ftj,Rd = 226.08 - 40.22 185.86 Front plate - tension - group
Ft,wb,Rd(4 + 3) - ∑33 Ftj,Rd = 224.81 - 40.22 184.59 Beam web - tension - group
Ft,ep,Rd(4 + 3 + 2) - ∑32 Ftj,Rd = 325.78 - 138.60 187.18 Front plate - tension - group
Ft,wb,Rd(4 + 3 + 2) - ∑32 Ftj,Rd = 294.11 - 138.60 155.51 Beam web - tension - group
Ft,ep,Rd(4 + 3 + 2 + 1) - ∑31 Ftj,Rd = 452.16 - 251.64 200.52 Front plate - tension - group
Ft,wb,Rd(4 + 3 + 2 + 1) - ∑31 Ftj,Rd = 436.23 - 251.64 184.59 Beam web - tension - group
Nj,Rd = ∑ Ftj,Rd
WELD RESISTANCE
Aw = 4813 [mm2] Area of all welds [4.5.3.2(2)]
Iwy = 50491137 [mm4] Moment of inertia of the weld arrangement with respect to the hor. axis [4.5.3.2(5)]
CONNECTION STIFFNESS
Axial force in the beam exceeds 5% of the Npl,Rd strength. According to point 6.3.1.(4), connection stiffness cannot be
calculated.
WEAKEST COMPONENT:
BEAM WEB - TENSION
REMARKS
Distance of bolts from an edge is too small. 16 [mm] < 22 [mm]
Connection Verification
GENERAL
Connection no.: 3
Structure node: 5
Structure bars: 1, 7
GEOMETRY
COLUMN
Section: UC 305x305x97
Bar no.: 1
Material: S275
BEAM
Section: UB 254x102x28
Bar no.: 7
Material: S275
PLATE
Type: bilateral
Material: S275
Material: S275
Material: S275
BOLTS
WELDS
acp = 10 [mm] Fillet welds connecting plate with column
MATERIAL FACTORS
M0 = 1.00 Partial safety factor [2.2]
LOADS
Case: 3: COMB1 1*1.35+2*1.50
RESULTS
Nw,Ed = -123.73 [kN] Axial force in the web Nw,Ed = (Nb,Ed*Aw)/Ab
Nfu,Ed = -80.92 [kN] Axial force in the upper flange Nfu,Ed = (Nb,Ed*Af)/Ab
Nfl,Ed = -80.92 [kN] Axial force in the lower flange Nfl,Ed = (Nb,Ed*Af)/Ab
BOLT CAPACITIES
Fv,Rd = 195.43 [kN] Shear bolt resistance in the unthreaded portion of a bolt Fv,Rd= 0.6*fub*Av*m/M2
Direction x
k1x = 2.50 Coefficient for calculation of Fb,Rd k1x = min[2.8*(e1/d0)-1.7, 1.4*(p1/d0)-1.7, 2.5]
Direction z
Direction x
Direction z
e= 88 [mm] Distance between centroid of a bolt group and center of column flange
FNx = 30.93 [kN] Component force in a bolt due to influence of the longitudinal force FNx=|Nw,Ed|/n
FVz = 0.05 [kN] Component force in a bolt due to influence of the shear force FVz=|Vb,Ed|/n
FMx = 0.08 [kN] Component force in a bolt due to influence of the moment on the x direction FMx=|M0|*zi/∑(xi2+zi2)
FMz = 0.08 [kN] Component force in a bolt due to influence of the moment on the z direction FMz=|M0|*xi/∑(xi2+zi2)
Fx,Ed = 31.01 [kN] Design total force in a bolt on the direction x Fx,Ed = FNx + FMx
Fz,Ed = 0.13 [kN] Design total force in a bolt on the direction z Fz,Ed = FVz + FMz
FEd = 31.01 [kN] Resultant shear force in a bolt FEd = ( Fx,Ed2 + Fz,Ed2 )
FRdx = 56.89 [kN] Effective design capacity of a bolt on the direction x FRdx=min(FbRd1x, FbRd2x)
FRdz = 73.14 [kN] Effective design capacity of a bolt on the direction z FRdz=min(FbRd1z, FbRd2z)
BOLT CAPACITIES
Fv,Rd = 57.91 [kN] Shear resistance of the shank of a single bolt Fv,Rd= 0.6*fub*Av*m/M2
FRd = 45.16 [kN] Effective design capacity of a bolt FRd=min(FvRd, FbRd1, FbRd2)
BOLT CAPACITIES
Fv,Rd = 57.91 [kN] Shear resistance of the shank of a single bolt Fv,Rd= 0.6*fub*Av*m/M2
FRd = 45.16 [kN] Effective design capacity of a bolt FRd=min(FvRd, FbRd1, FbRd2)
PLATE
Ant = 700 [mm2] Net area of the section in tension
VeffRd = 263.29 [kN] Design capacity of a section weakened by openings VeffRd=0.5*fu*Ant/M2 + (1/3)*fy*Anv/M0
BEAM
Ant = 410 [mm2] Net area of the section in tension
VeffRd = 200.67 [kN] Design capacity of a section weakened by openings VeffRd=0.5*fu*Ant/M2 + (1/3)*fy*Anv/M0
Mc,Rdnet = 13.71 [kN*m] Design resistance of the section for bending Mc,Rdnet = W net*fyp/M0
Av,net = 1400 [mm2] Net area of a section effective for shear Avnet=Av-nv*d0
Mc,Rdnet = 19.14 [kN*m] Design resistance of the section for bending Mc,Rdnet = W net*fyp/M0
Av,net = 1389 [mm2] Net area of a section effective for shear Avnet=Av-nv*d0
WELD RESISTANCE