Escolar Documentos
Profissional Documentos
Cultura Documentos
Mechanism, Type A2
V01/13 (20/02/13)
02
Contents
Contents
1. Package contents
04
Package contents
1. PACKAGE CONTENTS
Battery
Skate
SILL
Optional: Photocell
Set contents
SET FOR GIBS 2PT & 2PC A2 SET FOR DOOR SUSPENSION 2PT & 2PC A2
PART PCS PART PCS
FLANGE HEX NUT Μ8 DIN 6923 4 FLANGE HEX NUT Μ8 DIN 6923 4
JAM NUT Μ8 DIN 936 4 GALVANISED COACH BOLTS Μ8x13 DIN 603 3,5mm 4
LOCK SPACER Φ8 DIN 6798-AZ 4 PANEL SPACER 4
GALVANISEZ COACK BOLTS Μ8x13 DIN 603 3,5mm 4
GIBS 4
DOOR GIBS AXLE-Α2 4 SET FOR SILL ASSEMBLY 2PT A2
SET FOR CAR DOOR MECHANISM PART PCS
PART PCS SLOTTED FLAT HEAD SCREWS Μ5x10 DIN 963 4
HEX NUT Μ10-1,5 DIN 934 4 FLANGE HEX NUT Μ6 DIN 6923 12
SPACER Φ10 WITH EXTERNAL Φ30 DIN 9021 4 CLIPS FOR BOLTS Μ5 (RAPIDA "U" - TR 521 2B) 4
LOCK SPACER Φ10 DIN 6798-AZ 4 GALVANISED COACH BOLTS Μ6x16 DIN 603 12
SQUARE OF CABIN ROOF 4
MOUNTING BRACKET OF
CAR MECHANISM MAGNET GAP BETWEEN MAGNET & SENSOR
7-12mm
MAGNET
07
SILL Installation
3. Sill Installation
08
SILL Installation
3. SILL INSTALLATION
Step 1: Place the SILL above its base. SILL must be placed as shown in the right picture.
M6 DIN 6923
FLOOR
LEVEL
30mm
09
Car door mechanism installation
Step 1: Place the special square head screws to the roof guide rails
(Set for car door mechanism)
Step 2: Place the car door mechanism above the cabin, so that the zero point of the mechanism will be on the
cabins closing corner panel and across the zero point of the door mechanism (in case of landing door mechanism
pre-installation)
(Set for car door mechanism
Tools: Key Νο 17)
Mechanism
zero point
Zero point
of cabin’s closing
corner panel
11
Car door mechanism installation
By placing the bubble level horizontally on the guides of the car door mechanism, check its flatness and
adjust it if necessary by the screws of the mechanism’s brackets.
Step 4: Leveling of the car door mechanism towards the vertical plane.
(Tools: Bubble level)
Point where spacers
can be placed in order to
adjust the flatness of the
mechanism, if necessary.
By placing the bubble level vertically on the guides of the car door mechanism, check its flatness and adjust it
if necessary, by placing spacer between the bracket and and the guide rail of the cabin.
12
Car door mechanism installation
Step 5: Check if the car door mechanism is parallel to the entrance of the cabin.
d=15,00mm
from the rear side of the
mechanism to the external
side of cabin’s corner panel.
d
When the installation of landing door frame and mechanism is taking place firstly and the installation of the cabin
and the car door mechanism, check the distance between the rear side of the cabin and the landing door
mechanism to be 186mm, for the correct placement of the car door mechanism.
between the rear sides of cabin and
landing door mechanism
d=186,00mm
13
Panels installation
5. Panels installation
14
Panels installation
5. PANELS INSTALLATION
Step 1: First, assemble the suspension bolts of panels with flange hex nut.
(Set for door suspension 2PT & 2PC A2)
Μ8 DIN 936
Car
Plate
15
Panels installation
Step 3: Assemble the door gibs plate and place them to the door panel by using the suspension bolts. This can
be done in the same way as for suspending panels at the mechanism.
(Set for gibs 2PT & 2PC A2
Tools: Spanner Νο 13)
Μ8 DIN 936
Φ8 DIN 6798 ΑΖ
Door gibs
Panel side
reinforcement
6. Panels gap
17
Panels Gap
6. PANELS GAP
a. Between panels
3mm ~ 5mm
L 7mm
Gap between
panels and
header 2~3mm
L
7. Skate installation
19
Skate installation
7. SKATE INSTALLATION
Step 1: Place the skate.
(Tools: Allen Key Νο 4)
Φ6 DIN 6798 AZ