Escolar Documentos
Profissional Documentos
Cultura Documentos
ABC rings
1
Configuration and seal principle /
The ABC seal is a floating type seal
configured of split rings, fitted to the
shaft using garter springs. The ABC
seal follows the runout of the shaft.
The typical configuration of an ABC
seal is one that combines two sets of
ABC rings to make a double seal. The
barrier box between the ABC rings is
pressurized to a pressure approxi-
mately 0.02MpaG higher than the
purge gas induced pressure inside
the device.
This pressure difference prevents
flow material (fluid) leaking out of the
vessel into the atmosphere.
Vessel side
Atmospheric side
Features /
1. Accommodates axial runout
The ABC seal accommodates vessels
with rough accuracy in areas such as
axial runout and locomotion.
2. Maintenance free
The ABC seal is maintenance free be-
cause it has an automatic follow con-
figuration that works even if it becomes
worn.
3. Long lifespan
The ABC seal has an average lifespan
of approximately five years, which
means that it is effective in keeping run-
ning costs low.
4. Replacement possible without
dismantling device
The ABC seal is a split-ring type that
can be replaced without dismantling the
vessel.
2
ABC ring materials /
Material / Application /
Glass Filled PTFE Standard /
Carbon For high-speed applications /
Others (graphite filled PTFE, etc.) Select according to specifications /
This ring has a small gap This ring's bore surface is This ring has an additional
between the bore surface in contact with the shaft, outer ring on the outside
of the ring and the shaft. but has gaps of approxi- of the R-ring to enhance
mately 1mm at the split seal performance.
points.
3
Cartridge type ABC seal unit /
〈Before〉 〈After〉
ABC
F
Seal
Purge gas
Air filter & Regulator
Pressure relation
Vessel pressure < Blow gas pressure < Purge gas pressure
5
【Track record by device】
Representative
Vessel types Applicable device names
diagram numbers
Centrifuge (case seal) T2-07349
Centrifuge
Centrifuge (pipe seal) T3-30971
Extruder T2-05503
Extruder
Twin screw extruder T2-08323
Glass lined vessel mixer T3-31007
Nauta mixer (bottom seal) T3-26304
Mixer Nauta mixer (side chopper) T3-26305
Side-type mixer T2-06525
Upright-type mixer T2-07202
Drier T2-07368
Drier
Upright-type drier (shaft movement possible) T2-04312
Kneader Kneader T2-07367
Screw conveyor (horizontal type) T3-28250
Conveyor
Screw conveyor (inclined) T3-16926
Blower Blower T3-31001
Compressor Screw compressor T3-28816
Expander Expander T3-25427
Grinder mill Grinder mill T3-30371
Rotary valve Rotary valve T3-36649
Fermenter Fermenter T2-07403
Horizontal shaft type mixed flow pump (negative pressure seal section) T3-21558
Pump
Cooling water pump T3-27636
6
Service Network
JAPAN SHANGHAI
Headquarters & Tokyo Sales Office TANKEN SEAL(SHANGHAI) CO.,LTD.
3-14-15,Yaguchi, ota-ku, Tokyo 146-0093 RmA206,No2633 West YanAn Road,Shang-Mira
PHONE +81-3-3750-2151 Commercial Centre ChangNing District,
FAX +81-3-3750-5171 P.R.C. ZIP 200336
E-MAIL eigyoka@tankenseal.co.jp TEL. (021)6210-1731 FAX. ( 021)6210-1751
HP:https://www.tankenseal.co.jp