Escolar Documentos
Profissional Documentos
Cultura Documentos
com
menu
Request A Quote
Download
Product Catalog
ASTM A106 seamless pressure pipe (also known as ASME SA106 pipe) is
commonly used in the construction of oil and gas re neries, power plants,
petrochemical plants, boilers, and ships where the piping must transport uids
and gases that exhibit higher temperatures and pressure levels.
Leave a message
American Piping Products stocks a full range of A106
pipe (SA106 Pipe) in:
Grades B and C
NPS ¼” to 30” diameter
Schedules 10 through 160, STD, XH and XXH
Schedules 20 through XXH
Wall Thickness beyond XXH, including:
– Up to 4” wall in 20” through 24” OD
– Up to 3” wall in 10” through 18” OD
– Up to 2” wall in 4” through 8” OD
A/SA 106 Grade B specs are listed below. If you’re looking for Grade B-speci c
product o erings, click here.
Scope
ASTM A106 Seamless Pressure Pipe (also known as ASME SA106 pipe) covers
seamless carbon steel nominal wall pipe for high-temperature service. Suitable
for bending, anging and similar forming operations.
NPS 1-1/2″ and under may be either hot nished or cold drawn. NPS 2″ and
larger shall be hot nished unless otherwise speci ed.
Process
Killed steel, with primary melting process being open-hearth, basic-oxygen, or
electric-furnace, possibly combined with separate degassing or re ning.
Chemical Requirements
Download Chart
Grade A Grade B Grade C
1/8 to 1-1/2 [6 to 40], incl 1/64 (0.015) 0.4 1/64 (0.015) 0.4
Over 1-1/2 to 4 [40 to 100], incl 1/32 (0.031) 0.8 1/32 (0.031) 0.8
Over 4 to 8 [100 to 200], incl 1/16 (0.062) 1.6 1/32 (0.031) 0.8
Over 8 to 18 [200 to 450], incl 3/32 (0.093) 2.4 1/32 (0.031) 0.8
Over 18 to 26 [450 to 650], incl 1/8 (0.125) 3.2 1/32 (0.031) 0.8
Over 26 to 34 [650 to 859], incl 5/32 (0.156) 4.0 1/32 (0.031) 0.8
Over 34 to 48 [850 to 1200], incl 3/16 (0.187) 4.8 1/32 (0.031) 0.8
Tensile Requirements
Seamless
Hydrostatic Testing
Inspection test pressures produce a stress in the pipe wall equal to 60% of
speci ed minimum yield strength (SMYS) at room temperature. Maximum
Pressures are not to exceed 2500 psi for NPS3 and must stay under 2800 psi for
the larger sizes. Pressure is maintained for not less than 5 seconds.
Leave a message
Mechanical Tests Speci ed
Tensile Test — NPS 8 and larger — either transverse or longitudinal acceptable
Smaller than NPS 8 — weighed in lots. Larger sizes — by length. Flattening Test
— NPS 2-1/2 and larger. Bending Test (Cold) — NPS 2 and under.
Lengths
Lengths required shall be speci ed on order. No “jointers” permitted unless
otherwise speci ed. If no de nite lengths required, following practice applies:
Single Random — 17′ ~ 24′ lengths Double Random — 36′ ~ 44′ lengths
Referenced Documents
ASTM A 530/A 530M Speci cation for General Requirements for Specialized
Carbon and Alloy Steel Pipe
ASTM E 213 Practice for Ultrasonic Examination of Metal Pipe and Tubing
ASTM E 309 Practice for Eddy-Current Examination of Steel Tubular
Products Using Magnetic Saturation
Leave a message
ASTM E 381 Method of Macroetch testing Steel Bars, Billets, Blooms, and
Forgings
ASTM E 570 Practice for Flux Leakage Examination of Ferromagnetic Steel
Tubular Products
ASME B36.10M Welded and Seamless Wrought Steel Pipe
General Information
Orders for material under this speci cation should include the following, as
required, to describe the desired material adequately:
Hydrostatic test
Special requirements
© 2018 American Piping Products Inc. | 825 Maryville Centre Drive, Suite 310 | Chester eld, Missouri 63017
Toll Free: 1-800-316-5737 | International: 00-1-636-536-1775 | Fax: 636-536-1363
Leave a message