Escolar Documentos
Profissional Documentos
Cultura Documentos
CODE : 00ZXEA203VPME
ELECTRONIC
CASH REGISTER
[XE-A203]
XE-A203
MODEL XE-A213
[XE-A213]
(For “V” version)
CONTENTS
Parts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
Bi-Sn-Ag-P p
Bi-Sn-Ag
1. MASTER RESETTING
Master resetting clears the entire memory and resumes initial values.
Procedure :
1) Unplug the AC cord from the wall outlet, or set the mode switch to OFF position.
2) Let the ECR be witout the memory backup battery.
3) Wait over 1 minute for discharging.
4) Set the mode switch to any position except OFF.
5) Plugin the AC cord to the wall outlet, or turn the mode switch from OFF position to another position.
6) Insert batteries before carrying out operation after master resetting.
The master reset can also be accomplished in the following case.
In case power failure occurs when the machine has no battery attached to it, the master reset operation is automatically performed after the power
has been restored.
(This is because if power failure occurs with no battery attached to the machine, all the memories are lost and the machine does not work properly
after power recovery; this requires the master reset operation.)
Note: In case power failure occurs when the machine has no battery attached to it, the master reset operation is automatically performed after the
power has been restored.
1–1
CHAPTER 2. PROGRAM MODE
1. READING STOROGRAMS
The machine allows you to read every program stored in the PGM mode.
■ Key sequence for reading stored program
Report name Key sequence
Programming report 1 TL/NS
(*1) : PLU code range can be specified by entering the start and end numbers according to the following procedure.
When specifying a single time interval, PLU code, the start number has only to be entered.
■ SAMPLE PRINTOUTS
1. Programming report 1 (For example XE-A213V)
:
F 78 BILL
HEADER F 79 EJ FUNCTION NO. /TEXT
F 80 EJ END
05/02/2006 123456#123456 DATE/MACHINE NO./CC-NO. SHARP
12:34PM 01 M.KLERK____ TIME/CLERK NO/CLERK NAME PRESENTS THE
BEST ECR LOGO TEXT
*PGM* MODE TITLE
SHARP (It is according with LOGO FORMAT.)
IS
F01 ( - ) xxxxxx 007 FUNCTION NO./TEXT/PROGRAM (*1)
-1000.00 AMOUNT WITH SIGN THE BEST
F02 % xxxxxxxxxx 000 FUNCTION NO./TEXT /PROGRAM (*1) #5 00000000 (JOB#5) FUNCTION SELECT
L100.00% -10.00% HALO WITHOUT SIGN/RATE WITH SIGN #6 00000000 (JOB#6) PRINT FUNCTION
F04 DIFFERxxxxxx #7 00000000 (JOB#7) RECEIPT PRINT FORMAT
FUNCTION NO. /TEXT
F05 TAX1 STxxxxx #8 0000 (JOB#8) EURO FUNCTIONS
: #10 00000 (JOB#10) POWER SAVING PROGRAMMING
: #11 0 (JOB#11) LOGO FORMAT
: #12 00 (JOB#12) EURO PROGRAMMING
F 31 ***RAxxxxxxx 9 #13 00/00/0000 (JOB#13) EURO CHANGING DATE
FUNCTION NO. /TEXT/HALO (Printed by Date format)
F 32 ***POxxxxxxx 9 #14 00:00
(JOB#14) EURO CHANGING HOUR
F 33 CASH xxxx 008 #15 00000000 (JOB#15) FUNCTION SELECT2
F 34 CHECK1xxxxxx 008 #35 0007 (JOB#35) USB Timeout time
F 35 CHECK2xxxxxx 008 FUNCTION NO. /TEXT/PROGRAM (*2) T1 10.0000% TAX1 RATE
F 36 CREDIT1xxxxx 008 TAX1 STxxxxx 123.45 TEXT/ LOWER TAX LIMI
F 37 CREDIT2xxxxx 008 T2 4.0000% TAX2 RATE
F 38 EXCH1xxxxxxx 002 FUNCTION NO. /TEXT/PROGRAM (*3) TAX2 STxxxxx 0.10 TEXT/ LOWER TAX LIMIT
ABCD 999.999999 CURRENCY SYMBOL/RATE T3 -5.0000% TAX3 RATE
F 39 EXCH2xxxxxxx TAX3 STxxxxx 0.20 TEXT/ LOWER TAX LIMIT
FUNCTION NO. /TEXT
F 40 EX1 CHKxxxxx T4 ------ TAX4 ("------":INHIBIT)
: C #01 M.KLERK____ Clerk No./Clerk name
: C #02 CLERK02xxxxx
: : : VARIOUS PROGRAM
C #25 CLERK25xxxxx Refer to the programming section about
The printing of "reserved" is skippd.
the data of each JOB.
C: LIMITATION DIGITS (for (-) key) C: LIMITATION DIGITS (for (-) key)
(0 FIXED for [%n]) = 0 to 7 LIMITATION DIGITS (0=INHIBIT) = 0 to 8
2–1
(*3) : EXCH PROGRAM 4. Printer density report
A: OPEN RATE ENTRY A
ENABLE 0 HEADER
DISABLE 1
05/02/2006 123456#123456 DATE/MACHINE NO./CC-NO.
B: PRESET RATE ENTRY B 12:34PM 01 M.KLERK TIME/CLERK NO/CLERK NAME
ENABLE 0 *PGM* MODE TITLE
DISABLE 1 #50 50 Thermal printer density
10 : 0123456789AB Printing Sample
20 : 0123456789AB (Light&Shade value between
C: TAB C
30 : 0123456789AB 10 to 90.)
0 0 40 : 0123456789AB
50 : 0123456789AB
0.0 1 60 : 0123456789AB
0.00 2 70 : 0123456789AB
80 : 0123456789AB
0.000 3 90 : 0123456789AB
HEADER
HEADER
05/02/2006 123456#123456 DATE/MACHINE NO./CC-NO.
12:34PM 01 M.KLERK TIME/CLERK NO/CLERK NAME
05/02/2006 123456#123456 DATE/MACHINE NO./CC-NO.
12:34PM 01 M.KLERK TIME/CLERK NO/CLERK NAME *PGM* MODE TITLE
D01 T1234 073 DEPT CODE /TAXABLE /
*PGM* MODE TITLE DPT.01xxxxxx -1234.56 PROGRAM (*1)
D02 T1234 073 TEXT /PRICE WITH SIGN
DPT.02 -1234.56
#61 00000000 (JOB#61) OTHERS1 :
#62 00000000 (JOB#62) OTHERS2 :
#63 00000000 (JOB#63) OTHERS3 D99 T1234 071 (MAX department is decided by
#64 00000000 (JOB#64) OTHERS4 DPT.99 0.00 PGM selection.)
#65 00000000 (JOB#65) OTHERS5
#66 00000000 (JOB#66) OTHERS6
(*1) DEPT PROGRAM : ABC
#67 00000000 (JOB#67) OTHERS7
#68 00000000 (JOB#68) OTHERS8 A: REGISTRATION TYPE A
#69 00000000 (JOB#69) OTHERS9
NORMAL 0
#70 00000000 (JOB#70) OTHERS10
#71 SICS 1
GT2 $00000000000.00 GT2
#72
B: LIMITATION DIGITS = 0 to 7
GT3 $00000000000.00 GT3 C: AMOUNT ENTRY TYPE C
#76 Z1 0000 GENERAL Z1 RESET COUNTER
#77 Z2 0000 GENERAL Z2 RESET COUNTER Inhibited 0
#85 ___* DOMESTIC CURRENCY SYMBOL Open 1
#86 00 TRAINING CLERK
#87 **TRAINING** TRAINING MODE TEXT
Preset 2
#88 0 LANGUAGE MODE Open and Preset 3
#90 0 (For the fixed messages)
EJ/PLU MEMORY TYPE 6. PLU data report
(0 : TYPE, 1 : TYPE2)
: OTHERS PROGRAM
Refer to the programming section about the data of each JOB. HEADER
2–2
2. USER PROGRAMMING
1) PROGRAMMING FOR MEDIA KEYS ■ FUNCTION LIST (only for A213V)
([#/TM/ST] (XE-A203V) or [ST] (XE-A213V) key is used for program- DEFAULT TEXT
F-NO. FUNCTION
ming of CASH.) 123456789012
1 (-) (-)
XE-A203V:
0 2 %1 %1
3 Reserved
ABC #/TM/ST TL/NS
(for CASH) 4 DIFFER DIFFER
5 TAXABLE1 ST TAX1 ST
2–3
DEFAULT TEXT DEFAULT TEXT
F-NO. FUNCTION F-NO. FUNCTION
123456789012 123456789012
53 NET 2 (TAXABLE2 -VAT2) NET 2 25 Reserved
54 NET 3 (TAXABLE3 -VAT3) NET 3 26 CUSTOMER (TRANS. COUNT) GUEST
55 NET 4 (TAXABLE4 -VAT4) NET 4 27 Reserved
56 SUBTOTAL SUBTOTAL 28 PAID TOTAL PAID TL
57 MDS SBTL MDSE ST 29 AVERAGE AVE.
58 TOTAL ***TOTAL 30 Reserved
59 CHANGE CHANGE 31 RA ***RA
2–4
3) PROGRAMMING OF LOGO TEXT 5) FOREIGN CURRENCY SYMBOL PROGRAMMING
XE-A203V: XE-A203V:
NO CHANGE
NO CHANGE
#/TM/ST 6 (CHARACTERS) #/TM/ST TL/NS
#/TM/ST 4 X (CHARACTERS)
LINE NO.
#/TM/ST TL/NS XE-A213V:
NO CHANGE
ST 6 (CHARACTERS) ST TL/NS
XE-A213V:
NO CHANGE
(CHARACTERS): CHARACTER (Max. 4 Characters)
ST 4 X (CHARACTERS)
LINE NO. Characters can be entered by using the character layout on keyboard or
ST TL/NS
using numeric keys on keyboard.
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS:
X: LINE NO. (1-6)
YYY3 [00] KEY
(CHARACTERS): CHARACTER (Max. 24 Characters)
YYY : CHARACTER CODE (3 DIGITS)
Characters can be entered by using the character layout on keyboard or ( or [000] KEY ACCORDING TO PGM PRESET)
using numeric keys on keyboard.
MRS = ____ (_: space code)
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS: Note: This symbol is printed as the amount of EXCHANGE for PRESET
RATE only.
YYY3 [00] KEY
The amount symbol of EXCHANGE for OPEN RATE is not printed.
YYY : CHARACTER CODE (3 DIGITS)
( or [000] KEY ACCORDING TO PGM PRESET)
6) TAX RATE PROGRAMMING
(Sample) XE-A203V: (Inhibition programming)
VOID ( )
0
SHARP
PRESEMTS THE #/TM/ST 9 A yxxx.xxxx
TAX No. TAX RATE
MRS = BEST ECR & SIGN
SHARP
0
IS
THE BEST xxxxx
LOWER TAX LIMIT
FOR ADD TAX
4) PROGRAMMING OF CLERK NAME
#/TM/ST TL/NS
XE-A203V:
NO CHANGE
XE-A213V: (Inhibition programming)
#/TM/ST 5 XX (CHARACTERS)
VOID ( )
#/TM/ST TL/NS 0
ST 9 A yxxx.xxxx
XE-A213V:
TAX No. TAX RATE
NO CHANGE & SIGN
ST 5 XX (CHARACTERS)
0
ST TL/NS
xxxxx ST TL/NS
2–5
7) [AUTO] KEY PROGRAMMING 10) VARIOUS PROGRAMMING
There are programmed by depressing [#/TM/ST] (XE-A203V) or [#/ST] (XE-
max 25 A213V) key after a data that want to set.
And it is operated continuously until depressing the [TL/NS] key.
AUTO (Free key) AUTO TL/NS
(Programming Sequence)
Delete XE-A203V:
0
It must be pushed same [AUTO] key as the programming [AUTO] key at
#/TM/ST AB (NK) #/TM/ST TL/NS
the end of any key entry.
Note: [ESC] key cannot be set at [AUTO] key programming. XE-A213V: 0
It acts as a key of ERROR ESCAPE function in this programming.
ST AB (NK) ST TL/NS
< [AUTO] key function >
This machine has [AUTO] key which can be programmed the key- AB : JOB No.
sequence data. NK : PROGRAMMING DATA. (Numeric Keys)
When [AUTO] key is depressed, the machine works as same as the
programmed key-sequence is entered.
[JOB#1] MACHINE No. (6digits) -- XXXXXX --
Executing mode : REG, MGR, OPXZ, X1/Z1, X2/Z2 MRS = 000000
Setting mode : PGM
[JOB#2] CONSECUTIVE No. (6digits) -- XXXXXX --
8) EURO STATUS FUNCTION MRS = 0000
The ECR has a EURO STATUS in the preset memory.
It is changed by EURO CHANGING JOB and confirmed by EURO STA- [JOB#5] FUNCTION SELECT -- ABCDEFGH --
TUS READING JOB at Z2 mode. Refer XZ report section. MRS = 00000001
XE-A203V: ENABLE 0 ★
XXXXXXXX DISABLE 1
DATE
#/TM/ST B: RA in REG mode B
HHMM
ENABLE 0 ★
TIME DISABLE 1
XE-A213V:
XXXXXXXX C: SUBTOTAL VOID in REG mode C
DATE
ENABLE 0 ★
ST
DISABLE 1
HHMM
TIME D: INDIRECT VOID in REG mode D
ENABLE 0 ★
DATE) XXXXXXXX: YYYYMMDD or DDMMYYYY or MMDDYYYY DISABLE 1
(YYYY: 2000-2099)
(MM: 01-12) E: DIRECT VOID in REG mode E
(DD: 01-31) ENABLE 0 ★
The date entry format complies with PGM-mode. DISABLE 1
H: FRACTIONAL QUANTITY H
YES (3digits decimal place) 0 ★
NO 1
2–6
[JOB#6] PRINT FORMAT -- ABCDEFGH -- [JOB#8] EURO FUNCTIONS -- ABCD --
MRS = 11000111 MRS = 0000
A: PRINTER FORMAT A
A: Printing of EX amount for Total and Change A
JOURNAL 0
No 0 ★
RECEIPT 1 ★
Yes 1
Note: Case of RECEIPT, ECR is controled the Journal Rewind Motor B: Not used (Fixed at “0”)
as below.
C: CHECK,CREDIT operation for EX1 C
REG/MGR/VOID mode : Journal Rewind Motor is not driven.
PGM/OPXZ/XZ mode : Journal Rewind Motor is driven for rewinding No 0 ★
reports anytime. Yes 1
B: CONTENTS OF RECEIPT B D: EXCHANGE Calculation method D
TOTAL 0 Multiplication 0 ★
DETAIL 1 ★ Division 1
C: TIME PRINTING (for all receipt) C
PRINT 0 ★
[JOB#10] POWER SAVING -- YXXX --
NOT PRINT 1
MRS = 0030
D: DATE PRINTING (for all receipt) D
PRINT 0 ★ Y: POWER SAVING function when a time is displayed Y
NOT PRINT 1 Yes (Enable) 0 ★
No (Disable) 1
E: CONSECUTIVE NO. PRINTING E
PRINT 0 ★ XXX: POWER SAVING TIME to POWER OFF
= 001--254 (minutes)
NOT PRINT 1 or 999 (Inhibit)
F: SEPARATER LINE IN XZ REPORT F
[JOB#11] LOGO PRINTING -- A --
1 LINE FEED 0
SEPARATOR LINE 1 ★ MRS = 5
C: SUBTOTAL PRINT AT [ST] - KEY C A: Automatic converting the unit price at EURO A
NOT PRINT 0 ★ YES 0 ★
PRINT 1 NO 1
D: Not used (Fixed at “0”) B: The EURO CHANGING JOB at the date of exchang- B
ing the currency between LOCAL and EURO.
E: VAT/TAX AMOUNT PRINTING E
Compulsory 0 ★
PRINT 0 ★
Non-compulsory 1
NOT PRINT 1
[JOB#13] THE DATE OF EXCHANGING THE CURRENCY
F: TAXABLE AMOUNT PRINTING F
BETWEEN LOCAL AND EURO -- XXXXXXXX --
PRINT 0 ★
MRS = 00000000 (DD/MM/YYYY)
NOT PRINT 1
DATE) XXXXXXXX :YYYYMMDD or DDMMYYYY or MMDDYYYY
G: NET AMOUNT PRINTING G [YYYY:2000-2099]
PRINT 0 ★ [MM:01-12]
NOT PRINT 1 [DD:01-31]
00000000 = Function Inhibit.
H: PURCHASE NO. PRINTING H
The date entry format complies with the applicable PGM-mode pro-
PRINT 0 ★ gramming.
NOT PRINT 1 In case of date setting is 0, EURO date function is not work.
2–7
[JOB#14] THE TIME (HOUR ONLY) OF EXCHANGING THE [JOB#61] OTHERS1 PROGRAMMING -- ABCDEFGH --
CURRENCY BETWEEN LOCAL AND EURO -- XX -- MRS = 00100112
MRS = 00
A, B: Not used (Fixed at “00”)
XX : Hour (00-23)
C: Programming of MINUS dept/PLU C
[JOB#15] (Only for A213V) Disable 0
FUNCTION SELECT2 -- ABCDEFGH -- Enable 1 ★
MRS = 00011010 D: Fractional treatment D
A: PLU SHIFT LEVEL reset A Round off (4-DOWN, 5-UP) 0 ★
AUTO 0 ★ Raising to unit 1
MANUAL 1 Disregarding 2
No 1 ★ 1 1
2 2 ★
E: Printing of PB/NBAL on G.C.RCPT E 3 3
2–8
[JOB#63] OTHERS3 PROGRAMMING -- ABCDEFGH -- G: Reset GT1,2,3 at the general Z1 report G
MRS = 01000001 No 0 ★
A: Receipting at the time of NO SALE A Yes 1
Yes 0 ★
H: OP X/Z report H
No 1
Enable 0 ★
B: NO SALE after non-add code entry B Disable 1
Disable 0
Enable 1 ★
[JOB#65] OTHERS5 PROGRAMMING -- ABCDEFGH --
C: NON-ADD code entry C MRS = 10000000
Enable 0 ★
A: Printing of balance GT on Z report A
Disable 1
Yes 0
D: Copy Receipt D No 1 ★
No 0 ★ B: Balance GT Resetting at the general Z1 report B
Yes 1 No 0 ★
D: Printing of Training GT on Z report D Note: This selection is valid only when "PRINTING FORMAT" is
set as "JOURNAL".
Yes 0 ★
This selection is not valid for the printing data of EJ report.
No 1
It is provided another selection job for EJ.
2–9
[JOB#67] OTHERS7 PROGRAMMING -- ABCDEFGH -- [JOB#68] OTHERS8 PROGRAMMING -- ABCDEFGH --
MRS = 00000000 MRS = 00100011
MRS = 11821012 (for SCA) A: Not used (Fixed at “0”)
A: Printing of rounding amount (for SCA) A
No 0 (Only for XE-A213V)
B: Guest check No. B
Yes 1
Auto generation 0 ★
B: TOTAL AMOUNT ROUNDING when a transaction is B Manual 1
finalized directly by CHECK or CREDIT key (for SCA)
(This selection is not effective at Manual TAX system)
C: Temporary journal printing function of transaction C
YES (Rounding) 0
Disable 0
NO (Not rounding) 1
Enable 1 ★
C: ROUNDING UP OF THE UNIT DIGIT OF AMOUNT = 0 to 9 Note: It is a function to print one transaction data which is not finalized
(during a transaction) when a transaction is operated at
D: ROUNDING DOWN OF THE UNIT DIGIT OF AMOUNT = 0 to 9 "RECEIPT OFF".
Example) CD= 00: COMMON DESTINATION It is available only at "RECEIPT PRINTER TYPE".
82: SWITZERLAND
54: NORWAY
D: EJ print and clear at general Z1 report D
2 – 10
[JOB#69] OTHERS9 PROGRAMMING -- ABCDEFGH -- [JOB#86] TRAINING CLERK PROGRAMMING -- XX --
MRS = 00001000 MRS = 0
G: TAX PRINTING WHEN TAX IS ZERO G This symbol is printed with (+) amount of domestic currency.
The programmed characters is printed at left side of amount.
Yes 0 ★
Ex) Case of " DM ":
No 1
| DEPT.01 DM1.00 |
H: ROUNDING SYSTEM H 2
Programmed symbol
NORMAL 0 ★
SWEDEN 1 If some space characters are programmed at the left side of symbol
(like " *"), they are not counted as the number of character of the cur-
DENMARK 2
rency symbol. (In case of " DM", the number of character is 2.)
#/TM/ST 87 (CHARACTERS)
[JOB#71] GT2 PROGRAMMING -- XXXXXXXXXXXXX --
#/TM/ST TL/NS
MRS = 0000000000000
XE-A213V:
XXXXXXXXXXXXX : GT (13digits) NO CHANGE
ST 87 (CHARACTERS)
[JOB#72] GT3 PROGRAMMING --- XXXXXXXXXXXXX --
MRS = 0000000000000 ST TL/NS
XXXXXXXXXXXXX : GT (13digits)
(CHARACTERS): CHARACTER (Max. 12 characters)
[JOB#76] GENERAL Z1 RESET REPORT COUNTER Characters can be entered by using the character layout on keyboard or
-- XXXX -- using numeric keys on keyboard.
MRS = 0000 THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
XXXX : RESET COUNTER (4digits) BY NUMERIC KEYS IS AS FOLLOWS:
2 – 11
13) TEXT CHANGING (TO DEFAULT TEXT) 15) CHANGING MEMORY TYPE
(EJ RECORD AND PLU RECORD)
XE-A203V:
0
XE-A203V:
#/TM/ST 88 X TL/NS #/TM/ST 90 X TL/NS
XE-A213V: XE-A213V:
0
ST 90 X TL/NS
ST 88 X TL/NS
XE-A203V:
#/TM/ST 89 XX TL/NS
XE-A213V:
ST 89 XX TL/NS
All counter, totalizer, all GTs, and all Z counter are reset.
(Sample)
HEADER
2 – 12
4. CHARACTER ASSIGNMENT METHOD
xxx [00]
The status of [SHIFT], [NUMBER] and [DC] are keeping until pushing same control key in each text entry. (STAY DOWN type)
And the corresponding indication is lighted up on the display while their status is "on".
(Example)
[SHIFT] 3 [A] [B] [C] 3 [SHIFT] 3 [A] [B] [C] : Text "abcABC".
[NUMBER] 3 [1] [2] [3] 3 [NUMBER] 3 [1] [2] [3] : Text "123" and numeric number
123.
[DC] 3 [A] [B] [C] 3 [DC] 3 [A] [B] [C] : Text "ABCABC".
2 – 13
<Character Code Table for text programming> Printer
CODE CHARACTER CODE CHARACTER CODE CHARACTER CODE CHARACTER CODE CHARACTER
001 á 049 1 098 b 147 ù 196
002 â 050 2 099 c 148 à 197
003 ê 051 3 100 d 149 Æ 198
004 î 052 4 101 e 150 ∅ 199
005 ì 053 5 102 f 151 Å 200
006 í 054 6 103 g 152 ¤ 201
007 ô 055 7 104 h 153 é 202
008 ó 056 8 105 i 154 è 203
009 û 057 9 106 j 155 Pt 204
010 ú 058 : 107 k 156 ¡ 205
011 œ 059 ; 108 l 157 Ñ 206
012 060 < 109 m 158 Õ 207
Note: The character of this table is for reference.Please see actual print out.
(DC): Double Code
: ECR Control Character (Not used for text)
2 – 14
<Character Code Table for text programming> Display
CODE CHARACTER CODE CHARACTER CODE CHARACTER CODE CHARACTER CODE CHARACTER
001 á 049 1 098 b 147 ù 196 (Space)
002 â 050 2 099 c 148 à 197 (Space)
003 ê 051 3 100 d 149 Æ 198 (Space)
004 î 052 4 101 e 150 ∅ 199 (Space)
005 ì 053 5 102 f 151 Å 200 (Space)
006 (Space) 054 6 103 g 152 201 (Space)
007 ô 055 7 104 h 153 é 202
008 ó 056 8 105 i 154 è 203 (Space)
009 û 057 9 106 j 155 Pt 204 (Space)
010 ú 058 : 107 k 156 i 205 (Space)
011 (Space) 059 ; 108 l 157 Ñ 206
012 060 < 109 m 158 Õ 207
Note: The character of this table is for reference.Please see actual print out.
(DC): Double Code
: ECR Control Character (Not used for text)
2 – 15
5. EASY PROGRAMMING
Easy programming roughly consists of the following two types of pro- 1. DIRECT KEY OR CODE ENTRY TYPE
gramming.
1. Direct key or code entry type. <PROGRAMMING METHOD>
2. Guidance message type on usual programming. At PGM mode, it becomes set up mode, as it pushes a key of a direct
Reports that show the contents of individual programming can be key or code entry that it wants to set up.
printed. For example:
Push DEPT1 key, if you want to set up DEPT1 items.
Push %1 key, if you want to set up %1 item.
[PURPOSE] After that, every time it pushes [#/TM/ST](XE-A203V) or [ST](XE-A213V) key,
a set up item changes with price, text, programming ...
It aims to be able to program easily by using the guidance messages by
the easy programming. To change a programming content, it changes it using a numeric key.
As additional way, [00] key can be used as a incrementer while an indi-
cator lights on.
i.e. By pushing [00] key for a digit of parameters, a figure changes 0 3
[OPERATION] 1 3 2 ...
Perform the programming to enter the parameter according to the guid- The data is changed by pushing [#/TM/ST](XE-A203V) or [ST](XE-A213V)
ance message. key, and the display shows a content of the next item.
The guidance message is displayed on the LCD-display every time. After that, the operator program the next set up item.
It shows the information related the entry data at each step. If a set up ends, it pushes [TL/NS] key.
It shows the list of programmable data by this method ("Direct key entry
Each programming data and the text data is entered by using a key-
type") on the next page.
board.
It shows every set up item and example of display to the following.
It is used some key as special key to enter each data at the Easy Pro-
gramming operation. <KEY SEQUENCE>
There are follows. <DEPT>
<PLU>
Programmable Default
Function key Step Entry type
data (MRS)
PLU PLUn 1 Text (CHARACTER) PLU.xxxx
or 2 Price (NUMERIC) 0
PLU
code + 3 Dept code (NUMERIC) 01
[PLU/SUB] 4 Type (TOGGLE) PLU
2 – 16
<(-)> It shows every set up item and example of display to the following.
Programmable Default <The details of "ENTRY TYPE">
Function key Step Entry type
data (MRS)
As it pushes ST, a set up item advances the next step.
(-) (-) 1 Text (CHARACTER) (*2)
As it pushes TL, and the set up data writes to the memory, and a set up
2 Unit price (NUMERIC) 0 of the function ends.
3 Sign (TOGGLE) (-) Set up as it pushes other DIRECT PLU KEY on the way(exclude text
4 Item (TOGGLE) Enable programming),and the set up data writes to the memory, a set up of the
5 Subtotal (TOGGLE) Enable next setting starts.
6 Limitation digits (NUMERIC) 8 The guidance message is displayed at each programming step.
The following guidance messages are used for easy programming operation.
(*2) Please refer function list. (Programming of function text)
<Programming for DEPT.>
OPERATER
KEY ENTRY NOTE
<%n> 1234567890123456
Programmable Default [DPT1] DEPT . 01 01 DEPT1 TEXT/DEPT1 CODE
Function key Step Entry type
data (MRS) ENTER [ 00 ] KEY A text changes to ENTER [00]-KEY.
%n %n 1 Text (CHARACTER) (*2) ->[00] Message of "ENTER TEXT" is
ENTRY TEXT
2 Rate (NUMERIC) 0.00 displayed.
3 Sign (TOGGLE) (-) Current DEPT1 text is displayed.
DEPT . 01 Then the cursor is blinking.
4 Item (TOGGLE) Enable (*)
5 Subtotal (TOGGLE) Enable ->066 066 Text code is inputted.
6 % RATE halo (NUMERIC) 100.00 ->[00] If [00] key is entered and input-
BEPT . 01 ted text is addressed.
(*2) Please refer function list. (Programming of function text) Then the cursor is blinking.
->EER Text
BEER _
(_ is set space)
<EXCHANGE>
->[ST] PR I CE Guidance message
Programmable Default -> 123 Current setting is displayed.
Function key Step Entry type
data (MRS)
->200 200
EX EX 1 Text (CHARACTER) (*2) ->[ST] DEPT ENTRY TYPE Guidance message
2 Rate (NUMERIC) 0.000000 -> OPEN Current setting is displayed.
OPEN RATE ->[00] PRESET
3 (TOGGLE) Enable
ENTRY ->[00] OPEN & PRESET
PRESET RATE ->[00] I NH I B I TED
4 (TOGGLE) Enable
ENTRY ->[00] OPEN
5 TAB (NUMERIC) 2 ->[ST] SELECT OF TAX1 Guidance message
-> Guidance message
(*2) Please refer function list. (Programming of function text) TAX1 YES
Current setting is displayed.
Guidance message
-> [00] TAX1 NO
<RA, PO, CH1, CH2, CR1, CR2> Current setting is displayed.
->[ST] SELECT OF TAX2 Guidance message
Programmable Default
Function key Step Entry type -> TAX2 NO Guidance message
data (MRS)
->[00] TAX2 YES Guidance message
RA, PO, RA, PO, 1 Text (CHARACTER) (*2)
CH1, CH1, ->[ST] SELECT OF TAX3 Guidance message
CH2, CH2, Footer print on
2 (TOGGLE) NO -> TAX3 NO Guidance message
CR1, CR1, receipt
->[ST] SELECT OF TAX4 Guidance message
CR2 CR2 Entry of amount
3 (TOGGLE) (*3) -> TAX4 NO Guidance message
tendered
->[ST] REG I ST . TYPE Guidance message
4 Limitation digits (NUMERIC) (*4)
-> NORMAL Current setting is displayed.
(*2) Please refer function list. (Programming of function text) ->[00] S I CS
(*3) noncompulsory (check), inhibit (Credit) ->[ST] S I GN Guidance message
-> (+) Current setting is displayed.
(*4) 8 (CH1, CH2, CR1, CR2), 9 (RA, PO)
-> [00] (-)
->[ST] L I M I T D I G I TS Guidance message
-> 8 Current setting is displayed.
-> 7 7 Guidance message
->[ST] DEPT . 02 02 DEPT2 TEXT / DEPT2 CODE
ENTER [ 00 ] KEY RETURN TO 1'st STEP
->[TL] 0 . 00 DEPT1 SET UP TERMINATE
(*) In case of text setting, you can use [X] or [.] key.
If you push [X] key, the cursor moves to the left. And if you push [.]
key, the cursor moves to the right.
2 – 17
<CANCEL OPERATION> PROGRAMMING FOR (-).
OPERATER OPERATER
KEY ENTRY NOTE KEY ENTRY NOTE
1234567890123456 1234567890123456
[PLU5] PLU . 0005 0005 PLU1 TEXT / PLU CODE [(-)] ( - ) PROGRAMM I NG (-) PROGRAMMING
ENTER [00]-KEY TO CHANGE ENTER [ 00 ] KEY
ENTER [ 00 ] KEY
TEXT
->[00] Message of "ENTER TEXT" is
ENTER TEXT
Message of "ENTER TEXT" is displayed.
->[00] ENTER TEXT
displayed. Current (-) text is displayed.
( -)
PLU . 0005 Then the cursor is blinking.
->COFFEE COFFEE _ ->[ST] Message of "ENTER
ENTER AMOUNT
AMOUNT" is displayed.
->[ST] PR I CE Guidance message
-> 0
-> 100
->200 200 ->200 200
->[ST] S I GN Guidance message
->[ST] ENTER DEPT# PRICE IS DECIDED
-> (-)
-> 01
->[CL] 01 -> [00] (+)
->[ST] ENTRY FOR I TEM Guidance message
->[CL] 0 . 00 PLU5 SET UP TERMINATE
-> ITEM ENABLE
In this case, price(200) and text (COFFEE) are not written to the preset -> [00] I TEM D I SABLE
memory.
->[ST] ENTRY FOR SBTL Guidance message
-> SBTL D I SABLE
<Programming for PLU.> -> [00] SBTL ENABLE
OPERATER ->[ST] L I M I T D I G I TS Guidance message
KEY ENTRY NOTE
1234567890123456 -> 8 Current setting is displayed.
[PLU1] PLU . 0001 0001 PLU1 TEXT / PLU CODE -> 8 8
ENTER [ 00 ] KEY [ST] ( - ) PROGRAMM I NG (-) PROGRAMMING
->[00] Message of "ENTER TEXT" is ENTER [ 00 ] KEY
ENTER TEXT
displayed.
Current PLU1 text is displayed.
PLU. 0001
Then the cursor is blinking. (*)
PROGRAMMING FOR %.
->066 066 Text code is inputted.
OPERATER
->[00] If [00] key is entered and input- KEY ENTRY NOTE
BLU. 0001 ted text is addressed. 1234567890123456
Then the cursor is blinking. [%] % PROGRAMM I NG % PROGRAMMING
->EER Text ENTER [ 00 ] KEY
BEER
( is set space)
->[00] Message of "ENTER TEXT" is
->[ST] PRI CE Guidance message ENTER TEXT
displayed.
-> 100 Current setting is displayed. Current % text is displayed.
%
->200 200 Guidance message Then the cursor is blinking.
->[ST] ENTER DEPT# Guidance message/PLU code ->[ST] Message of "ENTER RATE" is
ENTER RATE
displayed.
->01 Inputted DEPT no.
01 If you want to set PLU delete. -> 0.00
Please set 0. ->12.34 12.34
->[ST] ENTER PLU TYPE Guidance message ->[ST] S I GN Guidance message
-> PLU Current setting is displayed. -> (-)
-> [00] SUBDEPT Guidance message -> [00] (+)
-> [00] PLU Guidance message ->[ST] ENTRY FOR ITEM Guidance message
->[ST] PLU . 0002 0002 PLU2 TEXT/PLU CODE -> I TEM ENABLE
ENTER [ 00 ] KEY RETURN TO 1'st STEP -> [00] I TEM D I SABLE
->[TL] 0. 00 PLU1 SET UP TERMINATE ->[ST] ENTRY FOR SBTL Guidance message
-> SBTL D I SABLE
(*) In case of text setting, you can use [X] or [.] key.
If you push [X] key, the cursor moves to the left. And if you push [.] -> [00] SBTL ENABLE
key, the cursor moves to the right. ->[ST] % HALO PROG Guidance message
-> 100. 00 Current setting is displayed.
-> 90.00 90. 00
[ST] % PROGRAMM I NG % PROGRAMMING
ENTER [ 00 ] KEY
2 – 18
PROGRAMMING FOR EXCHANGE. 2. GUIDANCE MESSAGE TYPE
OPERATER
KEY ENTRY NOTE
1234567890123456 <SAMPLE OPERATION & DISPLAY>
[ EX ] EXCHANGE PROG. EXCHANGE PROGRAMMING PROGRAMMING OF FUNCTION TEXT
ENTRY FOR I TEM
OPERATER
KEY ENTRY NOTE
->[00] Message of "ENTER TEXT" is 1234567890123456
ENTER TEXT
displayed.
[ST] -> 3 3 Numeric entry.
Current EXCH1 text is dis-
-> [•] FUNCTION TEXT PRO-
EXCH1 played. FUNC. TEXT PROG
GRAMMING TITLE
Then the cursor is blinking.
->[ST] Message of "ENTER EX ENTER FUNC NO. Enter function no.
ENTER EX RATE
RATE" is displayed. -> 4 4 Numeric entry.
-> 0 -> [X] _ Enter next key.
->123.456789 123. 456789 -> DIFFER D I FFER_ Text entry.
->[ST] OPEN RATE ENTRY Guidance message -> [ST] FUNCTION TEXT PRO-
FUNC. TEXT PROG
GRAMMING TITLE
-> OPEN ENABLE
-> [00] OPEN D I SABLE ENTER FUNC NO. Enter function no.
-> [TL] 0.00
->[ST] PRESET RATE Guidance message
-> PRESET ENABLE
-> [00] PRESET D I SABLE PROGRAMMING OF LOGO TEXT
->[ST] TAB Guidance message OPERATER
KEY ENTRY NOTE
-> 2 1234567890123456
-> 3 3 [ST] -> 4 4 Numeric entry.
->[ST] EXCHANGE PROG. Guidance message LOGO TEXT PROGRAM-
-> [•] LOGO TEXT PROG
MING TITLE
-> ENTER [ 00 ] KEY Guidance message
ENTER L I NE NO. Enter line no.
-> 1 1 Numeric entry.
PROGRAMMING FOR MEDIA KEYS & FUNCTION KEYS. -> [X] _ Enter next key.
([RA], [PO], [CH1], [CH2], [CR1], [CR2])
->
=S=H=A=R=P=_ Text entry.
OPERATER S_H_A_R_P_
KEY ENTRY NOTE
1234567890123456
LOGO TEXT PROGRAM-
-> [ST] LOGO TEXT PROG
[ CH1 ] CH1 PROGRAMMING MING TITLE
CH1 PROGRAMMING (Each media or function key
ENTER L I NE NO. Enter line no.
messages is displayed)
-> [TL] 0.00
ENTER [ 00 ] KEY
->[00] Message of "ENTER TEXT" is
ENTER TEXT
displayed.
PROGRAMMING OF CLERK NAME
Current CH1 text is displayed.
CHECK1 OPERATER
Then the cursor is blinking. KEY ENTRY NOTE
1234567890123456
->[ST] In case of RA/PO setting, this
FOOTER PR I NT [ST] -> 5 5 Numeric entry.
setting is skipped.
-> NO CLERK NAME PROGRAM-
-> [•] CLERK NAME PROG
MING TITLE
->[00] YES
ENTER CLERK NO . Enter clerk no.
->[ST] In case of RA/PO setting, this
AMOUNT TENDERED -> 1 1 Numeric entry.
setting is skipped.
-> COMPULSORY -> [X] _ Enter next key.
->[00] In case of CR1/CR2 setting -> CLERK01 CLERK01_ Text entry.
NON COMPULSORY
this message is "inhibit".
CLERK NAME PROGRAM-
-> [ST] CLERK NAME PROG
->[00] COMPULSORY MING TITLE
->[ST] L I M I T D I G I TS Guidance message ENTER CLERK NO . Enter clerk no.
-> 8 -> [TL] 0 . 00
->0 0
->[ST] CH1 PROGRAMMING Guidance message
-> ENTER [ 00 ] KEY Guidance message
2 – 19
FOREIGN CURRENCY SYMBOL PROGRAMMING (*) GUIDANCE TEXT
VARIOUS PROGRAMMING
DOMESTIC CURRENCY SYMBOL PROGRAMMING
OPERATER
KEY ENTRY NOTE OPERATER
1234567890123456 KEY ENTRY NOTE
1234567890123456
[ST] -> AB AB Numeric entry.
[ST] -> 85 85 Numeric entry.
-> [X] GU I DANCE TEXT Guidance text. (*)
DOMESTIC CURRENCY
Programming data. -> [.] DOM. CURRENCY
-> (NK) NK SYMBOL
NK = JOB-NO.
PROGRAMMING TITLE
-> [ST] ENTER TL KEY Enter TL key.
-> 224 -> [00] *_ Guidance text.
-> [TL] 0 . 00
-> [ST] ENTER TL KEY Enter TL key.
-> [TL] 0 . 00
2 – 20
TRAINING MODE TEXT PROGRAMMING
OPERATER
KEY ENTRY NOTE
1234567890123456
[ST] -> 87 87 MODE
TRAINING MODE TEXT PRO-
GRAMMING
-> [.] TRA I N I NG TEXT
In a moment, display for text
programming will change.
-> **TRAIN-
**TRAINING**_ CHARACTER
ING**
-> [ST] ENTER TL KEY Enter TL key.
-> [TL] 0 . 00
OPERATER
KEY ENTRY NOTE
1234567890123456
[ST] -> 88 88 Numeric entry.
-> [X] TEXT CHANGING
LANGUAGE CHANGE
(To default text)
-> 1 1 Text no.
-> [TL] THANK YOU
0 . 00
OPERATER
KEY ENTRY NOTE
1234567890123456
[ST] -> 89 89 Numeric entry.
Resetting of all counter and
-> [X] MEMORY RESETT I NG
totalizer TITLE
-> [TL] 0.00
OPERATER
KEY ENTRY NOTE
1234567890123456
[ST] -> 90 90 Numeric entry.
-> [X] Resetting of all counter and
SELECT MEM . TYPE
totalizer TITLE
-> 1 1 TYPE
-> [TL] TYPE (EJ: 2000 records and
TYPE2
PLU 200 records)
0.00
2 – 21
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE
Roughly speaking, the following sales reports are available: [Purpose]
1) OP X/Z reports (individual cashier reports) The reports are each used to check sales data. The standard purposes
of taking these reports are as follows:
2) X1/Z1 reports (Daily total X and Z reports)
OP X/Z reports: These reports are taken by operators in order to report
3) X2/Z2 reports (Periodic total X and Z reports) their own sales data.
4) Flash-read reports (Display sales amount) X1/Z1 reports: These reports are taken by the supervisor or manager in
order to check and report daily sales totals at that point.
In addition to the above reports that are to be used for program check-
X2/Z2 reports: These reports are taken by the owner or manager in order
ing are also available. to check and report periodic (weekly or monthly) totals.
Flash-read: These reports are taken by the owner or manager in order
to check and display daily sales totals at that point.
[Operation]
In the table below those reports marked with a circle "F " can be printed.
PRINTING REPORT
MODE
KEY
REPORT NAME OPX/Z X1/Z1 X2/Z2 DATA FOR READING
ENTRY
X Z X1 Z1 X2 Z2
GENERAL TL/NS o o o o *1, *6
PLU BY RANGE PLU/SUB o o PLU CODE *1, *2
CLERK (ALL) CLK# o o *1
CLERK (INDIVIDUAL) CLK# o o *1, *3
HOURLY (ALL) #/TM/ST o o *1
GLU GLU o o (only for A213V) *1
GLU (CLERK) CRI o o (only for A213V) *1
BALANCE RA o (only for A213V) *1
OTHERS OPERATION
MODE
JOB# OPX/Z X1/Z1 X2/Z2 DATA FOR READING
X Z X1 Z1 X2 Z2
EJ report (ALL) 700 o o o o *5, *6
EJ report (Latest 10 records) 710 o o *5, *6
EURO CHARGE 800 o o *7
3–1
• Stop of printing reports (Report cancel function): [Action]
This ECR has the function of report stopping for PLU report and EJ
Individual counters for the following Z reports are incremented when
report. those reports are printed.
• Printing of GT on X reports: 1) General daily total report (Z1)
This ECR dose not print any GT on X reports.
2) General periodic total report (Z2)
[Additional function]
*1 To read respective reports, it is necessary to follow the procedure
(1) Overflow mark
below.
If the amount or quantity in any totalizer other than GT to be printed
Reading on X or Z reports exceeds a programmed limit, the indication mark
(X report) (overflow mark) is printed for the totalizer concerned.
KEY The overflow mark may be printed even if a totalizer does not reach
the maximum amount. This occurs, for example, when the amount
Resetting
(Z report) or quantity in the totalizer gets smaller than the maximum amount
due to the entry of a negative amount after the overflowing of the
totalizer. This means that when the totalizer overflows once, the
*2 PLU code range can be specified by entering the start and end overflow mark (for example,"!!") is printed.
numbers according to the following procedure.
When specifying a single PLU code, the start number has only to be (2) MODE TITLE
entered. Each report printed a MODE TITLE at a header of report.
The Report Titles are as follows.
All OPX report *OPX*
Reading
OPZ report *OPZ*
XXXX XXXX PLU/SUB
Start NO. End NO. X1 report *X 1*
Resetting
Z1 report *Z 1*
X2 report *X 2*
*3 The clerk code does not need to enter at the OPX/Z mode.
Z2 report *Z 2*
In OPX/Z mode, it is issued the report of the assigned cashier.
*4 Reading display only. (3) Report cancel function
The displayed amount can be cleared by [CL] key. It can be cancelled by turned the mode switch to MGR position
while the data is printed. (In this case, the contents of memory are
KEY CL not cleared.)
(Display amount) (Display initialize) <Print sample of Report cancel>
:
*5 To read respective contents, it is necessary to follow the procedure below. :
3–2
CHANGING EURO FUNCTION (Z2 MODE JOB)
This job is own to be able to be changed easily from local currency sys- [Action]
tem to EURO currency system in X2/Z2 mode. It is executed some of below JOBs which is needed for each status.
(Reading the current EURO status) 1) Issue General Z1 report.
2) Issue General Z2 report.
(X2/Z2 mode) 800 TL/NS 3) Clear GT1/2/3 and Training GT.
4) Convert the unit price of DEPT/PLU from LOCAL currency to EURO.
(Changing EURO Function) If new unit price is over the max digits, its price is set as "0.00".
5) Convert the HALO amount and HALO digits from LOCAL currency
(X2/Z2 mode) 800 Y TL/NS
to EURO.
If new HALO amount is over the max digits, its price is set as "0.00".
Y: 1 = EURO STATUS (B) 6) Change PGM function "EX1 AMOUNT PRINTING FOR TOTAL
AND CHANGE YES/NO".
2 = EURO STATUS (C)
7) Change PGM function "EX1 CALCULATTION METHOD
3 = EURO STATUS (D) DIVISION/MULTIPLICATION".
8) Set "Domestic currency symbol" as EURO SYMBOL.
About EURO STATUS are shown the following pages.
It is executing automatically to change from status (A) to status (B), (C), (D). 9) Set "Domestic TAB" as "2".
Selectable type is one of below 4 types. 10) Set "EX1 currency symbol" as the suitable data.
And the selectable type is decided as below for each status. 11) Set "EX1 TAB" as the suitable data.
12) Set "Rounding SYSTEM (Denmark/Sweden/Normal)" as "Normal".
CURRENT STATUS Selectable STATUS 13) Set "Rounding up/down of the unit digits of AMOUNT" as "No".
4 (A) (B) (C) (D) 14) Set "Lowest digit entering limitation of item" as "Arbitrary".
(A) ------ u u u 15) Set "Lowest digit entering limitation of payment" as "Arbitrary".
(B) ------ ------ u u 16) Set "Difference memory" as "No".
17) Set "Rounding of foreign currency for EX" as "Round off (4-DOWN,
(C) ------ ------ ------ u
5-UP)". (EURO Regulation)
(D) ------ ------ ------ ------ Note:
Marked "u " is selectable a) This JOB cannot set below additional EURO function auto-
matically.
Below items must be set by each PGM JOB after this job.
(1) EX1 RATE
(2) "CHECK, CREDIT operation for EX1 Yes/No "
b) When the unit price is converted, the rounding method of EURO
currency is fixed as "Round off (4-DOWN, 5-UP)".
[EURO Regulation]
Selected STATUS
CURRENT STATUS (A)
(B) (C) (D)
1) General Z1 report ISSUE ISSUE ISSUE
2) General Z2 report ISSUE ISSUE ISSUE
3) GT1/2/3 ------ CLEAR CLAER
4) Convert the unit price of DEPT/PLU ------ CONVERTING CONVERTING
5) Convert the HALO amount and HALO digits ------ CONVERTING CONVERTING
6) EX1 AMOUNT PRINTING FOR TOTAL AND CHANGE "YES" "YES" "NO"
7) EX1 CALCULATTION METHOD "DIVISION" "MULTI." "MULTI."
8) Domestic currency symbol ------ [EURO] [EURO]
9) Domestic TAB ------ "2" "2"
10) EX1 currency symbol [EURO] The Current "Domestic
------
currency symbol"
11) EX1 TAB "2" The Current "Domestic TAB" ------
12) Rounding SYSTEM (Denmark/Sweden/Normal) ------ "Normal" "Normal"
13) Rounding up/down of the unit digits of AMOUNT ------ "No" "No"
14) Lowest digit entering limitation of item ------ "Arbitrary" "Arbitrary"
15) Lowest digit entering limitation of payment ------ "Arbitrary" "Arbitrary"
16) Difference memory ------ "No" "No"
17) Rounding of foreign currency for EX "ROUND OFF (4DOWN-5UP)" "ROUND OFF (4DOWN-5UP)" "ROUND OFF (4DOWN-5UP)"
Marked "------" is remaining the current data.
3–3
Current status (B):
Selected STATUS
CURRENT STATUS (B)
(C) (D)
1) General Z1 report ISSUE ISSUE
2) General Z2 report ISSUE ISSUE
3) GT1/2/3 CLEAR CLAER
4) Convert the unit price of DEPT/PLU CONVERTING CONVERTING
5) Convert the HALO amount and HALO digits CONVERTING CONVERTING
6) EX1 AMOUNT PRINTING FOR TOTAL AND CHANGE "YES" "NO"
7) EX1 CALCULATTION METHOD "MULTI." "MULTI."
8) Domestic currency symbol [EURO] [EURO]
9) Domestic TAB "2" "2"
10) EX1 currency symbol The Current "Domestic [SPACE]
currency symbol"
11) EX1 TAB The Current "Domestic TAB" ------
12) Rounding SYSTEM (Denmark/Sweden/Normal) "Normal" "Normal"
13) Rounding up/down of the unit digits of AMOUNT "No" "No"
14) Lowest digit entering limitation of item "Arbitrary" "Arbitrary"
15) Lowest digit entering limitation of payment "Arbitrary" "Arbitrary"
16) Difference memory "No" "No"
17) Rounding of foreign currency for EX "ROUND OFF (4DOWN-5UP)" "ROUND OFF (4DOWN-5UP)"
Marked "------" is remaining the current data.
3–4
ELECTRONIC JOURNAL REPORT
This job is own to print and clear EJ memory in X1/Z1 mode and OPXZ mode.
[Key sequence]
1) Reading and resetting of all records :
[OPXZ, X1/Z1 mode]
(Reading)
700 TL/NS
(Reseting)
710
[ACTION]
It prints all or parts of printing data in EJ memory.
The printing format is same as each operation.
It is able to print and clear the EJ memory at general Z1 report by PGM
mode programming.
In that case, the contents of EJ memory is printed just after issued gen-
eral Z1 report.
(Issuing general Z1 report 3 Clear daily DEPT & TRANS memory 3
Issuing EJ memory 3 Clear EJ memory)
3–5
COPYRIGHT 2006 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted.
In any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
SHARP CORPORATION
Information and Communication Systems Group
Products Quality Assurance Department
Yamatokoriyama, Nara 639-1186, Japan
2006 May Printed in Japan t