Escolar Documentos
Profissional Documentos
Cultura Documentos
com
PROPRIETARY NOTE
THIS SPECIFICATION IS THE PROPERTY OF BOE HF AND SHALL NOT BE
REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE OT AND
MUST BE RETURNED TO BOE HF UPON ITS REQUEST.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
REVISION HISTORY
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Contents
No ITEM Page
REVISIONS HISTORY 2
CONTENTS 3
1 GENERAL DESCRIPTION 4
1.1 Introduction
1.2 Features
1.3 Applications
1.4 General Specification
2 ABSOLUTE MAXIMUM RATINGS 6
3 ELECTRICAL SPECIFICATIONS 7
4 INTERFACE CONNECTION 9
4.1 Module Input Signal & power
4.2 Back-light Interface Connection
4.3 LVDS Interface
5 SIGNAL TIMING SPECIFICATIONS 12
5.1 Timing Parameter
5.2 Signal Timing Waveform
5.3 Input Signals, Basic Display Colors & Cray Scale Of Colors
5.4 Power Sequence
6 OPTICAL SPECIFICATIONS 16
7 MECHANICAL CHARACTERISTICS 18
8 RELIABLITY 19
9 PRODUCT SERIAL NUMBER 20
10 PACKING INFORMATION 21
11 HANDING & CAUTIONS 23
12 APPENDIX 24
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
1.1 Introduction
HT260WXC-100 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 26.0inch diagonally
measured active area with WXGA resolutions (1366 horizontal by 768 vertical pixel array).
Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and
this module can display 16.7M colors. The TFT-LCD panel used for this module is adapted for a
low reflection and higher color type.
RGB(Mini-LVDS)
Source Driver Circuit
S1 S1366
G1
+12.0V
Gate Driver Circuit
Timing Controller
LVDS CN1
5pair
[LVDS Rx & Mini-LVDS
(30pin) Tx integrated]
Option TFT - LCD Panel
#9 (1366 Ý RGB Ý 768 pixels)
1.2 Features
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
1.3 Application
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
< Table 2. LCD Module Electrical Specifications > [VSS=GND=0V]
Note : 1) Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 ఁ max. and no condensation of water.
ڀڋړ
ڋڑ
ڀڋڑ
ڋڐ ۀۂڼۍۊۏڮ
ڸڣڭڄڀڃڶٻ۔ۏۄڿۄۈېڣ
ڽۇېڝٻۏۀڲ
ڸڞڶٻۀۍېۏڼۍۀۋۈۀگ
ڋڏ
ڀڋڏ
ۉۊۄۏڼۍۀۋڪ
ڋڎ
ڋڍ
ڋڌ
ڋ
ڀڋڌ
ڋڍڈ ڋ ڋڌ ڋڍ ڋڎ ڋڏ ڋڐ ڋڑ ڋڒ ڋړ
¶ڶٻۀۍېۏڼۍۀۋۈۀگٻڽۇېڝٻ۔ۍڟCڸ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
[Ta =25ധ2 ଇ]
< Table 3. LCD Module Electrical Specifications >
Values
Parameter Symbol Unit Notes
Min Typ Max
Power Supply Input Voltage VDD 11.4 12 12.6 V
Power Supply Ripple Voltage VRP 300 mV
Power Supply Current IDD - 170 300 mA 1
Power Consumption of VDD PDD - 2 3.5 Watt
Rush current IRUSH - - 3.0 A 2
Differential Input High
VLVTH +100 mV
Threshold Voltage
LVDS
Interface Differential Input Low VLVTL -100 mV
Threshold Voltage
Common Input Voltage VLVC 1.0 1.2 1.4 V
Input High Threshold
VIH 2.7 - 3.3 V
CMOS Voltage
Interface Input Low Threshold
VIL 0 - 0.7 V
Voltage
Back-light Lamp Voltage VBL 1242 1380 1518 Vrms IBL=7.0 mA
Back-light Lamp Current IBL 6.5 7.0 7.5 mArms
Back-light Lamp operating
FL 40 - 80 KHz 3
Frequency
- - 2200 Vrms 25, 4
Lamp Start Voltage Vs
- - 2400 Vrms 0, 4
Lamp Life 50,000 - - Hrs IBL=7.0mA, 5
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Notes :
1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for VDD=12.0V, Frame rate=60Hz
and Clock frequency = 75.4MHz. Test Pattern of power supply current
a) Typ : Black Pattern
b) Max : Sub Dot Pattern
2. The duration of rush current is about 2ms and rising time of Power Input is 1ms(min)
White : 255Gray
Black : 0Gray
Mosaic Pattern(8 x 6)
3. The frequency range can be keep within ധ10% range of electrical and optical
characteristics. (except the chromaticity)
4. Output voltage of test circuit in order to stabilize discharge in tube. Lamp and
test circuit should be left at the above standard conditions over 1Hr.
5. The lifetime is judged to be over when any situation mentioned below occurs:
When the central lamp luminance decline to 50% of the initial luminance.
When the lamp starting voltage is 10% higher than its specification
6. Calculated value for reference (VBL ശ IBL) ശ4 excluding inverter loss
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Notes : 1. NC(Not Connected) : This pins are only used for BOE internal operations.
2. Input Level of LVDS signal is based on the IEA 664 Standard.
3. LVDS_SEL : This pin is used for selecting LVDS signal data format.
If this Pin : High (3.3V) or Open (NC) Æ Normal NS LVDS format
Otherwise : Low (GND) Æ JEIDA LVDS format
Sequence : On = Vdd ᆚLVDS Option ᆚInterface signal
Off = Interface signal ᆚLVDS Option ᆚ Vdd
1 IS100-L30B-C23 (UJU) 30
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
4 Male connectors
CP042ESFA00 (Cvilux)
Or Equivalent
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Notes: This product is DE only mode. The input of Hsync & Vsync signal does not have an effect on normal operation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
tCLK
DCLK 0.5 VDD
Valid data
First data Invalid data Pixel data Pixel data Invalid data
Valid data
Second data Invalid data Pixel data Pixel data Invalid data
DE(Data Enable)
tHP
HSync
tHV
DE(Data Enable)
tVP
VSync
tVV
DE(Data Enable)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
5.3 Input Signals, Basic Display Colors & Gray Scale Of Colors
< Table 7. Input Signal and Display Color Table >
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence
shall be as shown in below
WU`}kk WU`}kk
wGz WUX}kk WUX}kk
}kk W}
{X
{\ {]
{Y
}
pGz
OGpGkGP W}
{Z {[
is|GvuVvmmG
W}
Values
Parameter Units
Min Typ Max
T1 0.5 - 20 ms
T2 0 - 50 ms
T3 200 - - ms
T4 200 - - ms
T5 0 - 100 ms
T6 1 - - s
Notes:
1. When the power supply VDD is 0V, Keep the level of input signals on
the low or keep high impedance.
2. Do not keep the interface signal high impedance when power is on.
3. Back Light must be turn on after power for logic and interface signal are valid.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Note :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are
determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock
direction with respect to the optical axis which is normal to the LCD surface.
2. Contrast measurements shall be made at viewing angle of T= 0q and at the center of the LCD
surface. Luminance shall be measured with all pixels in the view field set first to white, then
to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio
(CR) is defined mathematically.
3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with
all pixels in the view field set first to white. This measurement shall be taken at the locations
shown in FIGURE 2 for a total of the measurements per display.
4. The White luminance uniformity on LCD surface is then expressed as :
ԩY = ( Minimum Luminance of 5points / Maximum Luminance of 5points ) * 100
(See FIGURE 2 shown in Appendix).
5. The color chromaticity coordinates specified in Table 9. shall be calculated from the spectral
data measured with all pixels first in red, green, blue and white. Measurements shall be made
at the center of the panel.
6. The electro-optical response time measurements shall be made as FIGURE 3 shown in
Appendix by switching the “data” input signal ON and OFF. The times needed for the
luminance to change from 10% to 90% is Td, and 90% to 10% is Tr.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
7.2 Mounting
See FIGURE 5. (shown in Appendix)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
The Reliability test items and its conditions are shown in below.
Period : X, Y, Z 30 min
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
ڋڋڌڈڞڳڲڋڑڍگڣ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
HT260WXC- 100 ]
WWWWWWWWWWWW YWXWUW[UY_U
W
WW W W WW W W WWWWWG
{ GGGnGGGsGGGGGGGGGtGGGGGp{ltTjvklGGGGGz
FG CODE
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
12.0 APPENDIX
ٻڄ ۈ ھ ڋ ڐٻ ژٻ ڧڃ
1/2V
3/4V
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
ۍگ ہگ
ۇڼھۄۏ ۋ ڪ ڈ ۊۍۏھۀۇ ڠ
ۀێۉ ۊ ۋێۀ ڭ
ڀڋڋڌ
ڀڋڔ
ڀڋڌ
ڀڋ
ۀ ۈۄگ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com