Escolar Documentos
Profissional Documentos
Cultura Documentos
C50L ®
B 90° B
ref
min grip
D min grip
E D
E
Truss Head – C50LT Large Truss Head – C50L30
C C
A A
B B
Fastener Dimensions
Round Head Truss Head Truss Head 90°Flush Thread Head
C50LT C50L30 Head C50LH
Dia. A B C B C B C B C B C
1/2 (16) .515 - .493 59/64 5/16 59/64 15/64 1 3/32 17/64 29/32 1/4
5/8 (20) .642 - .617 1 9/64 25/64 1 9/64 19/64 1 3/8 21/64 1 5/32 5/16
3/4 (24) .768 - .741 1 3/8 15/32 1 3/8 23/64 1 3/8 3/8
7/8 (28) .895 - .866 1 19/32 35/64 1 19/32 13/32 1 19/32 7/16
1 (32) 1.022 - .990 1 53/64 39/64 1 53/64 15/32 1 27/32 1/2
1 1/8 (36) 1.149 - 1.098 2 1/16 11/16
1 3/8 1.400-1.350 2-17/32 – * 27/32
version 4.0
58
76 4 3/4 - 5 5.713 7 43/64 5.933 8 5/32 6.018 8 21/32 6.323 9 5/8 6.500 9 13/16
80 5 - 5 1/4 5.963 7 59/64 6.573 9 7/8 6.750 10 1/16
84 5 1/4 - 5 1/2 6.823 10 1/8 7.000 10 5/16
88 5 1/2 - 5 3/4 7.073 10 3/8 7.250 10 9/16
92 5 3/4 - 6 7.323 10 5/8 7.500 10 13/16
version 4.0
59
Inspection Data
A properly installed C50L fastener will posses the dimensional characteristics tabulated below. Should the dimensions ‘A’ or ‘B’ exceed the indi-
cated values, the fastener is being used out-of-grip. A ‘C’ dimension less than the values specified is an indication of incomplete swage. A ‘D’ dimen-
sion exceeding the tabulated values is an indication of an incorrect or worn anvil on the installation tool. The ‘A’ dimension can be increased to 1/8 and
still meet all published values, provided there is no requirement to meet ASTM specifications pertaining to locking grooves (threads) in the shear plane.
5/8 C50L( )-( )20 LC-2R20G 3LC-2R20G 1/16 3/8 5/8 .916
C
3/4 C50L( )-( )24 LC-2R24G 3LC-2R24G 1/16 3/8 21/32 1.110
7/8 C50L( )-( )28 LC-2R28G 3LC-2R28G 1/16 3/8 3/4 1.282
LC collar
1 C50L( )-( )32 LC-2R32G 3LC-2R32G 1/16 3/8 7/8 1.465
3LC flanged collars
1 1/8 C50LR-BR36 LC-2R36G 1/16 3/8 29/32 1.646
1 3/8 C50LR-BR44 LC-2R44G 1/4 11/16 1 1/4 2.020
Collar Dimensions
Collar Diameter F G H J K
LC 1/2 .515 - .540 .800 - .765 .645 - .610
5/8 .650 - .665 1.010 - .970 .875 - .845 3
3/4 .775 - .790 1.180 - 1.165 .960 - .930
7/8 .910 - .935 1.375 - 1.345 1.113 - 1.083
1 1.025 - 1.050 1.575 - 1.535 1.275 - 1.230
C50L®
LC-2R
Installation Tooling
Dia. Installation Tool Nose Assembly Type
1/2 2620 99-5000 Hydraulic
2620PT 99-5002 Hydraulic
5/8 2624 / 2628 99-5008 Hydraulic
586 99-5008 Hydraulic
3/4 2628 99-5010 Hydraulic
586 99-5010 Hydraulic
7/8 506 99-5014 Hydraulic
1 507 99-5016 Hydraulic
1 1/8 507 99-5019 Hydraulic
1 3/8 12142 Integral Hydraulic
version 4.0
60
TM
Hole Data 4 TAB-LOK
1 When using 3LC collars, include J dimension in grip
Dia. Maximum Hole The Tab-Lok feature makes dimension to determine grip number.
1/2 9/16 sure the collar stays on the pin, 2 Optional collar at reduced clamping force and tensile
before installation, in overhead and strength. Contact HUCK for data. When using 8LC
5/8 11/16 down slanted pin placements. To collars, subtract J dimension from grip dimension to
3/4 13/16 order Tab-Lok collars refer to determine grip number.
3 H length for 20(5/8) diameter in F, I or 2CU material
7/8 15/16 ‘Options’ in the ‘How to Order’ is .805 - .770.
1 1 1/16 section of this brochure. 4 Except C50L60
1 1/8 1 3/16
1 3/8 1 1/2
Installation Sequence
Follow the form below to construct a part number for ordering C50L pins. Refer to the Grip Data chart for grip numbers.
1 CRES fasteners are available in 16 through 24 diameters and through 36 grips only.
C50L Collars
Follow the form below to construct a part number for ordering collars for C50L pins.
version 4.0