Escolar Documentos
Profissional Documentos
Cultura Documentos
60 mm System
800.426.0279 tgpamerica.com
SteelBuilt Curtainwall® Systems
Envision expansive window openings, with more glass and less frame. Imagine a curtainwall system that only
requires frame profiles one-third the size of traditional aluminum systems.
Now that dream is a reality with the new SteelBuilt Curtainwall® Systems from Technical Glass Products (TGP).
SteelBuilt Curtainwall Systems give you all the advantage of steel: greater strength, superior performance and
improved aesthetics. Utilized throughout Europe for many years, SteelBuilt Curtainwall Systems have been
tested to North American standards and are now available to open tremendous new design opportunities.
Office: 800.426.0279
425.396.8200
Fax: 800.451.9857
425.396.8300
E-mail: sales@tgpamerica.com
Web: tgpamerica.com
CSI-SPECIFICATION
Full copies of our detail drawings and CSI format Specifications can be downloaded from our Web site or
obtained from our office.
This Architectural Specification Manual provides a summary of the specification, design and applications that
can be achieved with SteelBuilt Curtainwall® Systems. Many special finishes and components are available,
please consult Technical Glass Products.
© 2014 Technical Glass Products. SteelBuilt Curtainwall, One Source. Many Solutions., TGP America
and Technical Glass Products are registered trademarks of Technical Glass Products.
800.426.0279 tgpamerica.com
Table of Contents
3
page
Isometric View - 60 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Profile Overview - 60 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Table of Contents
Wind Load Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-35
Thermal Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
contents
LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND
CURTAIN WALL PRODUCTS VARY WIDELY. TGP DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS,
OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR.
Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are
millimeters unless otherwise noted.
03|14
The following metric (SI ) units are found in these details:
m – meter
date
cm – centimeter
mm – millimeter
s – second
Pa – pascal
MPa – megapascal
TGP reserves the right to change configurations without prior notice when deemed necessary for product improvement.
800.426.0279 tgpamerica.com
Introduction
4
page
Features
• Offers all the advantage of steel: greater strength, superior performance and improved aesthetics
• Narrow sight line of 1-3/4” (45 mm) or 2-3/8” (60 mm)
• Variety of system depths
• Infill options up to 2”
• Stainless steel or anodized cover caps available
• Painted finishes in standard and custom choices
• Concealed fastener joinery creates smooth, monolithic appearance
• Shear block fabrication method
• Compatible with SteelBuilt Window & Doors® Systems
• Silicone compatible glazing materials for long-lasting seals
Introduction
Optional Features
• Stainless steel cover caps
• Custom aluminum cover caps available
• Steel reinforcing available
contents
Product Applications
• Ideal for low to mid-rise applications where large glass and narrow sight lines are desired
• Ideal choice for high span applications
• Coastal environments that benefit from the durability of stainless steel
03|14
date
800.426.0279 tgpamerica.com
1
page
60 mm system
60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
2
Isometric View
page
2
3
1
10
5
12
9
7
contents
03|14
date
4
11 13 15
800.426.0279 tgpamerica.com
60 mm System
3
Profile Overview
page
Profile Overview - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
2
1
800.426.0279
System in Curtainwall
Overview SteelBuilt Door
60 mm System
tgpamerica.com
date 03|14 contents Overview
ReferenceSteelBuilt
Details - Door
60 mmSystem
System
- 60 mm System page 4
60 mm System
5
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
6
Reference Details
page
Reference Details - 60 mm System
4
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
7
Reference Details
6 page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
8
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
9
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
10
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
11
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
12
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
13
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
14
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
15
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
16
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
17
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
18
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
19
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
20
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
21
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
22
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
23
Reference Details
page
Reference Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
24
Corner Details
page
Corner Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
25
Corner Details
page
Corner Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
26
Corner Details
page
Corner Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
27
Corner Details
page
Corner Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
28
Corner Details
page
Corner Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
29
Corner Details
page
Corner Details - 60 mm System
contents
03|14
date
800.426.0279 tgpamerica.com
60 mm System
30
Available Frame Profiles
page
Available Frame Profiles - 60 mm System
contents
03|14
date
Snap-on cover caps are interchangeable with 403-560 and 430-060 pressure plates.
800.426.0279 tgpamerica.com
Wind Load/Dead Load Charts
31
page
WIND LOAD CHARTS
Mullions are designed for deflection limitations in accordance with AAMA TIR-A11 of L/175 up to 13’-
6” and L/240 +1/4” above 13’-6”. These curves are for mullions WITH HORIZONTALS and are based on
precise engineering calculations for stress and deflection. Allowable wind load stress for STEEL 30,000
p.s.i. (207MPa.). Charted curves, in all cases are for the limiting value. A 4/3 increase in allowable
stress has not been used to develop these curves. For special situations not covered by these curves,
contact your TGP representative for additional information.
contents
pressure based on either a ½” or ¾” weather joint between lites of glass, and the shortest dimension
of the individual lite of glass. This chart is not meant to dictate final silicone bond line or loading
requirements. While TGP can assist in determining the bond line dimension, the silicone sealant
manufacturers must review and approve the final details, typically done during the shop drawing
phase of most projects.
THERMAL CHART
03|14
Thermal transmittance (U-Value) is a measure of the rate of heat loss of a building component. The
test method measures the thermal characteristics of the system under steady-state conditions.
date
800.426.0279 tgpamerica.com
Wind Load Charts
32
page
Single Span Twin Span
0.61 1.22 1.83 2.44 3.05 0.61 1.22 1.83 2.44 3.05
25 7.62 25 7.62
MODULE (M) MODULE (M)
6.10 6.10
20 20
A A
1.831" [46.50]
15 4.57 15 4.57
SPAN (M)
SPAN (M)
SPAN (FT)
SPAN (FT)
B B
3.05 10 3.05
10
D RP-1800 D
1.52 5 1.52
5 E
E
0
0 0 0
0 2 4 6 8 10 0 2 4 6 8 10
contents
CURVE 'A' - 10 PSF
CURVE 'B' - 20 PSF
CURVE 'C' - 30 PSF
CURVE 'D' - 40 PSF
CURVE 'E' - 50 PSF
Single Span Reinforced Twin Span Reinforced
0.61 1.22 1.83 2.44 3.05 0.61 1.22 1.83 2.44 3.05
25 7.62 25 7.62
MODULE (M) MODULE (M)
03|14
6.10 20 6.10
20
date
A A
0.500" [12.70]
15 4.57
15 4.57
1.831" [46.50]
B SPAN (M)
SPAN (FT)
SPAN (M)
SPAN (FT)
B
1.000" [25.40]
C
10 3.05
10 3.05
C
2.362" [60.00] D
D E
5 E 1.52
RP-1800 5 1.52
800.426.0279 tgpamerica.com
Wind Load Charts
33
page
Single Span Twin Span
0.61 1.22 1.83 2.44 3.05 0.61 1.22 1.83 2.44 3.05
25
25 7.62 7.62
MODULE (M) MODULE (M)
A
6.10 20 6.10
20
3.602" [91.50]
B
15 4.57
15 4.57
SPAN (M)
SPAN (M)
SPAN (FT)
SPAN (FT)
C 10 3.05
10 3.05
E
E RP-1802
5 1.52
5 1.52
0
0 0
0 0 2 4 6 8 10
0 2 4 6 8 10
MODULE (FT)
MODULE (FT)
contents
CURVE 'A' - 20 PSF
CURVE 'B' - 30 PSF
CURVE 'C' - 40 PSF
CURVE 'D' - 50 PSF
CURVE 'E' - 60 PSF
Single Span Reinforced Twin Span Reinforced
0.61 1.22 1.83 2.44 3.05 0.61 1.22 1.83 2.44 3.05
25 25
7.62 7.62
MODULE (M) MODULE (M)
0.500" [12.70]
03|14
A
A 6.10 20 6.10
20
date
B
3.602" [91.50]
B
2.750" [69.85]
15 4.57
15 4.57
C
SPAN (M)
SPAN (FT)
SPAN (M)
SPAN (FT)
D 3.05
10
10 3.05
E
E 2.362" [60.00]
1.52
RP-1802 5 1.52
5
w/ (2) 2-3/4" x 1/2"
Steel Bars
0
0
0
0 0 2 4 6 8 10
0 2 4 6 8 10 MODULE (FT)
MODULE (FT)
800.426.0279 tgpamerica.com
Wind Load Charts
34
page
Single Span Twin Span
0.61 1.22 1.83 2.44 3.05 0.61 1.22 1.83 2.44 3.05
25 7.62 25 7.62
MODULE (M) MODULE (M)
A
A
6.10 6.10
20 20
B B
5.374" [136.50]
15 4.57 15 4.57
C C
SPAN (M)
SPAN (M)
SPAN (FT)
SPAN (FT)
D D
3.05 10 3.05
10
E E
1.52 5 1.52
5
RP-1804
0 0 0
0
0 2 4 6 8 10
0 2 4 6 8 10
MODULE (FT)
MODULE (FT)
contents
CURVE 'A' - 20 PSF
CURVE 'B' - 30 PSF
CURVE 'C' - 40 PSF
CURVE 'D' - 50 PSF
CURVE 'E' - 60 PSF
Single Span Reinforced Twin Span Reinforced
0.61 1.22 1.83 2.44 3.05 1.22 2.44 3.66 4.88 6.10
25 7.62 25 7.62
MODULE (M) MODULE (M)
A A
03|14
0.500" [12.70]
6.10
B 6.10 20
20
B
date
C
C
5.374" [136.50]
D 15 4.57
15 4.57
4.500" [114.30]
SPAN (M)
SPAN (FT)
E
SPAN (M)
SPAN (FT)
10 3.05
E
10 3.05
2.362" [60.00]
5 1.52
5 1.52
RP-1804
w/ (2) 4-1/2" x 1/2" 0 0
0
0 Steel Bars 0 4 8
MODULE (FT)
12 16 20
0 2 4 6 8 10
MODULE (FT)
800.426.0279 tgpamerica.com
Wind Load Charts
35
page
Single Span Twin Span
0.61 1.22 1.83 2.44 3.05 0.61 1.22 1.83 2.44 3.05
25 7.62 25 7.62
MODULE (M) MODULE (M)
A
A
6.10 6.10
20 20
B
7.146" [181.50]
C
15 4.57 15 4.57
D
D
SPAN (M)
SPAN (M)
SPAN (FT)
SPAN (FT)
E
E
10 3.05 10 3.05
RP-1806
0 0 0 0
0 2 4 6 8 10 0 2 4 6 8 10
MODULE (FT) MODULE (FT)
contents
CURVE 'A' - 20 PSF
CURVE 'B' - 30 PSF
CURVE 'C' - 40 PSF
CURVE 'D' - 50 PSF
CURVE 'E' - 60 PSF
Single Span Reinforced Twin Span Reinforced
0.61 1.22 1.83 2.44 3.05 1.22 2.44 3.66 4.88 6.10
25 7.62 25 7.62
MODULE (M) MODULE (M)
B A
0.500" [12.70]
03|14
A
B
C
6.10 6.10
20 20
D C
date
E
D
7.146" [181.50]
15 4.57 15 4.57
6.250" [158.75]
E SPAN (M)
SPAN (M)
SPAN (FT)
SPAN (FT)
10 3.05
10 3.05
RP-1806
w/ (2) 6-1/4" x 1/2" 0 0
0
0
0 2 4 6 8 10 Steel Bars 0 4 8
MODULE (FT)
12 16 20
MODULE (FT)
800.426.0279 tgpamerica.com
Dead Load Charts (Tubular)
36
page
1/4" Glass 1" Glass
0.61 1.22 1.83 2.44 3.05 0.61 1.22 1.83 2.44 3.05
25.00 7.62 25.00 7.62
MODULE (M) MODULE (M)
1.831" [46.50]
15.00 4.57 15.00 4.57
B
SPAN (M)
SPAN (M)
B
A
RP-1800
5.00 1.52 5.00 1.52
0.00 0 0.00 0
0 2 4 6 8 10 0 2 4 6 8 10
HORIZONTAL SPAN (FT) HORIZONTAL SPAN (FT)
contents
A = 1/4 POINT LOADING
B = 1/8 POINT LOADING
03|14
20.00 6.10 20.00 6.10
date
3.602" [91.50]
B
15.00 4.57 15.00 4.57
HEIGHT OF GLASS (FT)
SPAN (M)
B
10.00 3.05 10.00 3.05
2.362" [60.00]
A
RP-1802
5.00 1.52 5.00 1.52
0.00 0 0
0.00
0 2 4 6 8 10 0 2 4 6 8 10
HORIZONTAL SPAN (FT) HORIZONTAL SPAN (FT)
800.426.0279 tgpamerica.com
Dead Load Charts (Tubular)
37
page
1/4" Glass 1" Glass
0.61 1.22 1.83 2.44 3.05 0.61 1.22 1.83 2.44 3.05
25.00 7.62 25.00 7.62
MODULE (M) MODULE (M)
5.374" [136.50]
15.00 4.57 15.00 4.57
HEIGHT OF GLASS (FT)
SPAN (M)
SPAN (M)
A
A
10.00 3.05 10.00 3.05
2.362" [60.00]
RP-1804
5.00 1.52 5.00 1.52
0.00 0 0.00 0
0 2 4 6 8 10 0 2 4 6 8 10
HORIZONTAL SPAN (FT) HORIZONTAL SPAN (FT)
contents
A = 1/4 POINT LOADING
B = 1/8 POINT LOADING
03|14
B
date
7.146" [181.50]
A B
15.00 4.57 15.00 4.57
HEIGHT OF GLASS (FT)
HEIGHT OF GLASS (FT)
SPAN (M)
SPAN (M)
2.362" [60.00]
5.00
RP-1806 5.00
1.52 1.52
0.00 0 0.00 0
0 2 4 6 8 10 0 2 4 6 8 10
HORIZONTAL SPAN (FT) HORIZONTAL SPAN (FT)
800.426.0279 tgpamerica.com
Silicone Glazing Charts
38
page
DIMENSION
A B C D E
Exterior
Gasket Sealant
Mullion Weather Total
Tape Contact
Width Joint B+C NARROWEST GLASS DIMENSION IN FT (Top Line of Chart)
Width Width
Width
1’ 2’ 3’ 4’ 5’ 6’ 7’ 8’ 9’ 10’
WIDE DIM.
follow this row further to the right until you reach
the appropriate narrowest glass dimension
contents
column (top row)
03|14
1. For 60 mm mullion width system, select the 19
mm weather joint width (column B, row 2)
date
2. Follow row to sealant contact bond width column
“E” (14.5 mm/ 9/16”)
3. The largest lite on the project is 68” x 120”. The
narrowest dimension is 68”, round up to 72” (6’)
4. Continue across the row to the right and look up
to the narrowest glass dimension in feet until
you get to the 6‘ column. 46 psf is the maximum
wind load
800.426.0279 tgpamerica.com
Thermal Charts
39
page
Thermal Transmittance1 (btu/hr + ft2 + °F)
Glass U-Factor3 Overall U-Factor2 NOTE: For glass values that are not listed, linear
interpolation is permitted.
Stainless Steel Aluminum
Cover Cap Cover Cap
1. U-Factors are determined in accordance with NFRC 100.
0.48 .51 .51 2. Glass properties are based on center of glass values
0.44 .49 .49 and are obtained from your glass supplier.
0.30 .35 .36 3. Overall U-Factor is based on the standard NFRC
0.247 .31 .32 specimen size of matrix 2000 mm wide by 2000 mm
high (78-3/4” by 78-3/4”).
0.123 .19 .20
Thermal Charts
contents
03|14
date
800.426.0279 tgpamerica.com