Escolar Documentos
Profissional Documentos
Cultura Documentos
FYRHED
HIGH VELOCITY WATER SPRAY NOZZLE
Fyrhed
Standard Nozzle Range
Picture
K–Factor K–Factor Thread Spray
Type No. (Metric) (US)
(Male) Angle
Approval Strainer
Tol. ± 5% Tol. ± 5%
Yes
C 2 26 1.81 1/2" NPT 80° (integral)
No
L 1 40 2.77 1" NPT 55° (optional)
1
No
D 1 49 3.41 1" NPT 65° (optional)
No
E 1 65 4.52 1" NPT 80° (optional)
No
F 1 89 6.15 1" NPT 85° (optional)
No
G 1 104 7.17 1" NPT 90° (optional)
Yes
WM 3 21 1.46 1" NPT 115° (integral) 2 3
No
WF 3 78 5.43 1" NPT 115° (optional)
75 Weight (brass)
58
55 L,D,E,F,G : 440 g
C : 235 g
WM : 232 g
The right is reserved to vary or modify any specifications without prior notice.
The right is reserved to vary or modify any specifications without prior notice.
• Apply a small amount of pipe joint • Care must be taken to ensure that the
compound or tape to the external replacement nozzle has the proper model,
threads of the nozzle, taking care not to style and K-factor. A cabinet should be
allow a build-up of compound on the provided and stocked with a suitable wrench
strainer or inside the inlet. and extra spray nozzles of each variety
• Hand-tighten the nozzle into the fitting. used for replacement purposes.
• Use a suitable wrench to finally install
and tighten the nozzle, applying a min. • The spray nozzle discharge pattern is
to max. torque of 9,5 to 19Nm (1/2” critical for proper fire protection. Hence,
thread) or 26 to 40Nm (1” thread) for a nothing should be hung from, attached to, or
leak tight joint. Higher levels of torque otherwise obstruct the discharge pattern. All
can distort the nozzle inlet with obstructions must be immediately removed
consequent impairment of the nozzle. or, if necessary, additional nozzles installed.
The right is reserved to vary or modify any specifications without prior notice.
Certification: 3.1 cert. to EN 10204 and/or Positive Material Identification (PMI) on request.
Part Numbers
K– K–
Factor Factor Nickel
Type Thread Spray St. Steel St. Steel
(Metric) (US) (Male)
Brass Aluminium Titanium
Angle SS316 SMO
Tol. ± Tol. ± Bronze
5% 5%
1/2"
C 26 1.81 NPT 80° D3102610N D3102616N D3102620N D3102609N D3102617N
G 104 7.17 1" NPT 90° D3110410N D3110416N D3110420N D3110409N D3110417N
The right is reserved to vary or modify any specifications without prior notice.
L / min
Pressure / Flow
250
240
230 K 104
220
210
200 K 89
190
180
K 78
170
160
150
K 65
140
130 K 57
120
K 49
110
100 K 47
90
K 40
80
70
60 K 26
50
K 21
40
30
20
10
0
3,00 3,50 4,00 4,50 5,00 Bar
Q = flow (l/min)
K = nozzle K-factor (discharge coefficient)
P = water pressure at nozzle (Barg)
The right is reserved to vary or modify any specifications without prior notice.
70
60 K 7.17
K 6.15
50
K 5.43
40
K 4.52
K 3.97
30 K 3.41
K 3.27
K 2.77
20
K 1.81
K 1.46
10
0
50,00 55,00 60,00 65,00 70,00 PSI
The right is reserved to vary or modify any specifications without prior notice.
1 1
3,5
2 2
5,0
3 3
4 4
3 2 1m 0
3 2 1m 0
Type D – K49 (3.41 U.S.) Type E – K65 (4.52 U.S)
0 0
D E
1 1
2 2
3 3
4 4
3 2 1m 0 3 2 1m 0
Type F – K89 (6.15 U.S) Type G - K104 (7.17 U.S)
0 0
F G
1 1
2 2
3,5
3 3
5,0
4 4
3 2 1m 0 3 2 1m 0
The right is reserved to vary or modify any specifications without prior notice.
1 1
2 2
3,5
3,5
5,0
3 3
5,0
4 4
3 2 1m 0 3 2 1m 0
Type WD – K47 (3.27 U.S.) Type WE– K57 (3.97 U.S.)
0 0
WD WE
1 1
2 2
3,5 3,5
3 5,0 3 5,0
4 4
3 2 1m 0 3 2 1m 0
Type WF – K78 (5.43 U.S.)
0
WF
2
3,5
3 5,0
4
3 2 1m 0
Horizontal spray profiles: see data sheet: WS 015 1002.1 A
The right is reserved to vary or modify any specifications without prior notice.