Escolar Documentos
Profissional Documentos
Cultura Documentos
Laeraxe Manual
1. Machine assembly and wire connect
2. Software installation and use
3. Question and answer 1ST COPY ALL FILE TO
4. Service and support
YOUR PC
https://www.dropbox.com/sh/07dwg4io1uqdbpa/AAAAQ5oomTeSdMvoEG9AXVSga?dl=0
4.connect the laser head(2.8w and 5.5w and 7w got TTL line, needs connect too)
5.insert the power supply cable to control card and then press the red button
if you read to here you will find insert power cable and press red button is the last step, this
will avoid burn the laser head and driver board.
Remember you must follow this turn, when you don't use it. just press the red button up
and pull out the power cable. then disconnect the USB cable is ok, must follow this turn.
1. Machine assembly and wire connect
1. white aluminum working area:170*200
2. white aluminum working area:300*400
3. white aluminum working area:350*500
Machine assembly(follow this video)http://cloud.video.taobao.com/play/u/2671973884/p/1/e/6/t/1/37645828.mp4
Control card sketch map: Port to insert 2800mw or 5500mw or 7000mw laser
head and insert TTL line to control power. 12V.
Make sure your have pressed down the USB port to connect PC
X Y Z limit port
red button(power button)
Port to insert
Z axis. No driver insert here, you
100mw-
can buy A4988 yourself or you can
2500mw laser
buy from us directly. Same as X
head 12v
and Y axis
X axis rotate this small screw clockwise to Double Y axis rotate this small screw clockwise to
increase current, otherwise reduce current, increase current, otherwise reduce current. This 2
you can set direction in CNCC soft setting area. port give opposite direction. You can set direction
in CNCC soft setting area.
X motor wire(4p wire in the black rubber pipe) Y motor wire(4p wire without black rubber pipe)
2800mw and 5500mw and 7000mw laser head
Machine wire connect sketch map:(2800mw and 5500mw and 700mw)
(1 RED TTL line in the black rubber pipe)
2800mw and 5500mw and 7000mw laser head
X motor wire(4p wire in the black rubber pipe) Y motor wire(4p wire without black rubber pipe)
The right wire connect turn before start: this is very important
As Hbot machine all shipping with assembled, when you get it just insert the 2 motor line. and fasten the laser head
hang plate. then hang on the laser head and fasten the 2 screw on the back.
1.tear off the adhesive tape and insert the 2 sides motor line.
3.fasten the laser head hang plate with 2 screw and nuts.
4.hang on the laser head, fasten the 2 screw. fasten the black rubber pipe with white plastic belt.
The right wire connect turn before start: this is very important
Below is view of New 2800mw and 5500mw laser head. Here add this picture
just let you know we will shipping new laser head in the future.
here is big part of red copper
inside, super cooling. The
continuous working time no
longer than 60 minutes, and
you need stop and Cooling 10-
15 minutes. Or the laser head
will Overheating burned, also
long time working will affect
the life time of laser head.
Here are the files in dropbox, also same in the DVD disk you got. will update in the
http://www.laseraxe-customize.com/
Dropbox:
https://www.dropbox.com/sh/07dwg4io1uqdbpa/AAAAQ5oomTeSdMvoEG9AXVSga?dl=0
4th step open the CNCC operate soft, note just open the
CNCC.exe is ok. there are 4 versions, all same. open the one
1st step assemble the machine can run on your PC is ok. suggest use the latest version.
Follow the steps just like the picture showing to install the driver and software.
open this folder if you cant operate with
CNCC soft, in this folder is Grbl soft. our
control card also support Grbl soft.
6th step open the test file and choose a photo or G code have a test. before
you do this, you need finish the assembling of laseraxe. and adjust the focus
of laser head.
1step assemble machine like below: open the "Laseraxe assemble" folder
follow the video and assemble detail to finish the assemble job, read file carefully.
2nd step install the driver like below:
note: we have 2 driver here(below red box), both are same. you can install any one of them is ok.
4th step open the CNCC folder, suggest use the latest version.
it after select the language, the software will ask you “do you want to
into English)
then re-open the soft, it will show the language you saved.
change language here, select English
Before start engraving, you need adjust the focus(7w-12w laser see below)
1. hang the laser head and make sure the hold frame at the bottom
2. connect you machine with cncc soft on PC
3. Use your finger to rotate the bottom ball under laser head to adjust the focus,
make sure the point on carved material to be a minimum point
CNCC is free of
installation, just select language, then
open and click save and reopen the soft
Auto connect is ok
re scan port
NOTE:IF YOU ONLY BOUGHT OUR CONTROL CARD NEEDS SETTLE THIS,IF YOU
BOUGHT WHOLE SET MACHINE JUST PASS ITEM 3.3
3.4.1 Import photo(from our test file, you can have a try)
engraving dimension
after click gray or outline after adjust well on top,
click create G-code
purple point is the start point, just for start positioning. this is set the engraving cycle times, you can
not where its start engraving, it always start engraving at set the engraving times you want like 2 or 3
the left bottom of the picture. it's hard to understand here maybe more. like more times to cutting.
click this to start the weak laser, then click
"Auxiliary" up down left right to move the
3.4.4 Adjust engraving position
laser to the start point you want
you must note"Primary model"just for gray scale photos,the rest"outline", "black
white" needs Advanced model. Read this carefully, carefully, carefully, carefully, carefully
1.import photos
2.choose space(usually 0.1)
3.photo processing(choose the style you like)
4.zoom(set the engraving dimension you want)
5.adjust burning time and power
6.start engraving grayscale photos
burning time of each pixel(usually set the power( this is just for gray scale setting)
choose 50ms)
note: this power and burning time just for gray scale
engraving photos.
3.6.1 Import photo(make sure your screen same as the below picture)
3.6.2choose spacing (usually0.1) and PR(choose the style you want and wait PC to process)
3.6.3 zoom(set the engraving dimension you want)
3.6.4 adjust burning time and power(depends on your laser head power)
3.6.5 start engraving
3.7Auxiliary(Manual operation)
http://www.laseraxe-customize.com/
Dropbox:
https://www.dropbox.com/sh/07dwg4io1uqdbpa/AAAAQ5oomTeSdMvoEG9AXVSga?dl=0
2
3. Open Region and Language
4
2. if all above 3 item you did and still can’t connect with pc.
1. Change another USB port on your pc.
2. Change another USB line to connect your pc again.
3. Connect US via support@laseraxe-customize.com
3. No lights from Laser head.
1. Insert the power supply directly into your laser head to see if it’s working, like below:
If the lights on from laser head, means the laser head is good. If not, that’s means the laser head
broken( Remember this should be tested after you make sure the power supply is good)
1. Don’t flash the card, because our card can connect with Grbl directly.
2. We have put Grbl soft in disk and our Dropbox link(some old disk may don’t have, please download
below link:
Dropbox:
https://www.dropbox.com/sh/07dwg4io1uqdbpa/AAAAQ5oomTeSdMvoEG9AXVSga?dl=0
3. install the Grbl soft then open and connect, choose the Baud rate 115200. Then will shown as below:
Choose the right port, each PC will be different.
SEE BELOW:
4. If you want move the spindle directly it will shown as below: see left bottom corner
5. Next you want start engraving, then choose file and start ok. Sometimes some .nc file incomplete, so
you need convert your .nc file with our developed “code to laser” soft(also put in our disk and
dropbox:https://www.dropbox.com/sh/07dwg4io1uqdbpa/AAAAQ5oomTeSdMvoEG9AXVSga?dl=0
6. You can open your .nc file with our”code to laser” soft then convert it and save, then input Grbl to
engraving.