Você está na página 1de 45

Cover

HOT ROLLED AND


STRUCTURAL STEEL PRODUCTS
98 Edition

Page 1
Notes:
1. All welds to AS/NZS 1554.1 Category SP (deep penetr
2. Web to flange joints develop the minimum tensile stren
3. Flame cut surfaces not incorporated in the welds have

Depth Depth
Designation kg/m of Flange Flange Web Between
Section Width Thickness Thickness Flanges
d bf tf tw d1
mm mm mm mm mm d1 / tw (bf-tw)/2tf
1200WB455 455 1200 500 40 16 1120 70.00
1200WB423 423 1192 500 36 16 1120 70.00
1200WB392 392 1184 500 32 16 1120 70.00
1200WB342 342 1184 400 32 16 1120 70.00
1200WB317 317 1176 400 28 16 1120 70.00
1200WB278 278 1170 350 25 16 1120 70.00
1200WB249 249 1170 275 25 16 1120 70.00
1000WB322 322 1024 400 32 16 960 60.00
1000WB296 296 1016 400 28 16 960 60.00
1000WB258 258 1010 350 25 16 960 60.00
1000WB215 215 1000 300 20 16 960 60.00
900WB282 282 924 400 32 12 860 71.67
900WB257 257 916 400 28 12 860 71.67
900WB218 218 910 350 25 12 860 71.67
900WB175 175 900 300 20 12 860 71.67
800WB192 192 816 300 28 10 760 76.00
800WB168 168 810 275 25 10 760 76.00
800WB146 146 800 275 20 10 760 76.00
800WB122 122 792 250 16 10 760 76.00
700WB173 173 716 275 28 10 660 66.00
700WB150 150 710 250 25 10 660 66.00
700WB130 130 700 250 20 10 660 66.00
700WB115 115 692 250 16 10 660 66.00
1554.1 Category SP (deep penetration)
develop the minimum tensile strength of the web
ot incorporated in the welds have a minimum surface roughness of class2, as defined in WTIA Technical Note 5.

About x-axis About y-axis

Gross Area of
Cross Section
Ag Ix Zx Sx rx Iy Zy Sy ry
d1 / tw (bf-tw)/2tf mm2 106mm4 103mm3 103mm3 mm 106mm4 103mm3 103mm3 mm
6.05 57900 15300 25600 28200 515 834 3330 5070
6.72 53900 13900 23300 25800 508 750 3000 4570
7.56 49900 12500 21100 23400 500 667 2670 4070
6.00 43500 10400 17500 19800 488 342 1710 2630
6.86 40300 9250 15700 17900 479 299 1500 2310
6.68 35400 7610 13000 15000 464 179 1020 1600
5.18 31700 6380 10900 12900 449 87.0 633 1020
6.00 41000 7480 14600 16400 427 342 1710 2620
6.86 37800 6650 13100 14800 420 299 1490 2300
6.68 32900 5430 10700 12300 406 179 1020 1590
7.10 27400 4060 8120 9570 385 90.3 602 961
6.06 35900 5730 12400 13600 399 341 1710 2590
6.93 32700 5050 11000 12200 393 299 1490 2270
6.76 27800 4060 8930 9960 382 179 1020 1560
7.20 22300 2960 6580 7500 364 90.1 601 931
5.18 24400 2970 7290 8060 349 126 840 1280
5.30 21400 2480 6140 6840 341 86.7 631 964
6.63 18600 2040 5100 5730 331 69.4 505 775
7.50 15600 1570 3970 4550 317 41.7 334 519
4.73 22000 2060 5760 6390 306 97.1 706 1080
4.80 19100 1710 4810 5370 299 65.2 521 798
6.00 16600 1400 3990 4490 290 52.1 417 642
7.50 14600 1150 3330 3790 281 41.7 334 516
y-axis

Torsion Warping
Constant Constant
Sy ry J Iw
103mm3 mm 103mm4 109mm6
120.0 22000 280000
118.0 16500 251000
116.0 12100 221000
88.6 9960 113000
86.1 7230 98500
71.1 5090 58700
52.4 4310 28500
91.3 9740 84100
89.0 7010 73000
73.8 4870 43400
57.5 2890 21700
97.5 8870 67900
95.6 6150 58900
80.2 4020 35000
63.5 2060 17400
71.9 4420 19600
63.7 2990 13400
61.1 1670 10600
51.7 921 6280
66.4 4020 11500
58.4 2690 7640
56.0 1510 6030
53.5 888 4770
WBDES

Welded Beams - Properties for Assessing Section Capacity

Notes:
1. For BHP-300PLUS sections the tensile strength (fu)
2. For Grade 400 sections the tensile strength (fu) is 48
3. C: Compact Section; N: Non-compact Section; S: Sle
4. BHP-300PLUS welded sections are produced to exc

About x-axis About y-axis


BHP-300PLUS

Flange Web Form


Compact- Zex Compact- Zey
Designation fy fy Factor Designation
ness 103 mm3 ness 103 mm3
MPa MPa kf

1200WB455 280 300 0.837 C 28200 C 5000


1200WB423 280 300 0.825 C 25800 C 4500
1200WB392 280 300 0.811 C 23400 N 4000
1200WB342 280 300 0.783 C 19800 C 2560
1200WB317 280 300 0.766 C 17900 C 2240
1200WB278 280 300 0.733 C 15000 C 1530
1200WB249 280 300 0.701 C 12900 C 949
1000WB322 280 300 0.832 C 16400 C 2560
1000WB296 280 300 0.817 C 14800 C 2240
1000WB258 280 300 0.790 C 12300 C 1530
1000WB215 300 300 0.738 C 9570 C 903
900WB282 280 310 0.845 C 13600 C 2560
900WB257 280 310 0.830 C 12200 C 2240
900WB218 280 310 0.800 C 9960 C 1530
900WB175 300 310 0.744 C 7500 C 901
800WB192 280 310 0.824 C 8060 C 1260
800WB168 280 310 0.799 C 6840 C 946
800WB146 300 310 0.763 N 5710 C 757
800WB122 300 310 0.718 N 4530 N 498
700WB173 280 310 0.850 C 6390 C 1060
700WB150 280 310 0.828 C 5370 C 782
700WB130 300 310 0.795 C 4490 C 626
700WB115 300 310 0.767 C 3790 N 498

Page 5
WBDES

tions the tensile strength (fu) is 430 MPa


s the tensile strength (fu) is 480 MPa
: Non-compact Section; S: Slender Section
sections are produced to exceed the minimum requirements of AS/NZS 3679.2-300.

About x-axis About y-axis


AS3679.2-400

Flange Web Form


Compact- Zex Compact- Zey
Designation fy fy Factor
ness 103 mm3 ness 103 mm3
MPa MPa kf

1200WB455 360 380 0.820 N 28100 C 5000


1200WB423 360 380 0.806 N 25700 N 4500
1200WB392 360 380 0.791 N 23300 N 3900
1200WB342 360 380 0.760 N 19600 C 2560
1200WB317 360 380 0.741 N 17700 N 2230
1200WB278 360 380 0.705 N 14900 N 1530
1200WB249 360 380 0.670 N 12800 C 949
1000WB322 360 380 0.807 C 16400 C 2560
1000WB296 360 380 0.791 C 14800 N 2230
1000WB258 360 380 0.760 C 12300 N 1530
1000WB215 380 380 0.704 C 9570 N 887
900WB282 360 400 0.830 N 13500 C 2560
900WB257 360 400 0.813 N 12000 N 2220
900WB218 360 400 0.780 N 9840 N 1530
900WB175 380 400 0.721 N 7320 N 882
800WB192 360 400 0.808 N 7850 C 1260
800WB168 360 400 0.781 N 6640 C 946
800WB146 380 400 0.744 N 5510 N 754
800WB122 380 400 0.695 N 4340 N 486
700WB173 360 400 0.833 C 6390 C 1060
700WB150 360 400 0.807 C 5370 C 782
700WB130 380 400 0.773 C 4490 C 626
700WB115 380 400 0.742 C 3790 N 486

Page 6
WCDIM

Welded Columns - Dimensions and Properties

Notes:
1. All welds to AS/NZS 1554.1 Category SP (deep penetration
2. Web to flange joints develop the minimum tensile strength
3. Flame cut surfaces not incorporated in the welds have a m

Depth Depth
Designation kg/m of Flange Flange Web Between
Section Width Thickness Thickness Flanges
d bf tf tw d1
mm mm mm mm mm d1 / tw (bf-tw)/2tf
500WC440 440 480 500 40 40 400 10.00 5.75
500WC414 414 480 500 40 32 400 12.50 5.85
500WC383 383 472 500 36 32 400 12.50 6.50
500WC340 340 514 500 32 25 450 18.00 7.42
500WC290 290 506 500 28 20 450 22.50 8.57
500WC267 267 500 500 25 20 450 22.50 9.60
500WC228 228 490 500 20 20 450 22.50 12.00
400WC361 361 430 400 40 40 350 8.75 4.50
400WC328 328 430 400 40 28 350 12.50 4.65
400WC303 303 422 400 36 28 350 12.50 5.17
400WC270 270 414 400 32 25 350 14.00 5.86
400WC212 212 400 400 25 20 350 17.50 7.60
400WC181 181 390 400 20 20 350 17.50 9.50
400WC144 144 382 400 16 16 350 21.88 12.00
350WC280 280 355 350 40 28 275 9.82 4.03
350WC258 258 347 350 36 28 275 9.82 4.47
350WC230 230 339 350 32 25 275 11.00 5.08
350WC197 197 331 350 28 20 275 13.75 5.89

Page 7
WCDIM

gory SP (deep penetration)


minimum tensile strength of a 16 mm web only
ted in the welds have a minimum surface roughness of class2, as defined in WTIA Technical Note 5.

About x-axis About y-axis

Gross Area of Torsion


Cross Section Constant
Ag Ix Zx Sx rx Iy Zy Sy ry J
(bf-tw)/2tf mm2 106mm4 103mm3 103mm3 mm 106mm4 103mm3 103mm3 mm 103mm4
56000 2150 8980 10400 196 835 3340 5160 122.0
52800 2110 8800 10100 200 834 3340 5100 126.0
48800 1890 7990 9130 197 751 3000 4600 124.0
43200 2050 7980 8980 218 667 2670 4070 124.0
37000 1750 6930 7700 218 584 2330 3540 126.0
34000 1560 6250 6950 214 521 2080 3170 124.0
29000 1260 5130 5710 208 417 1670 2540 120.0
46000 1360 6340 7460 172 429 2140 3340 96.5
41800 1320 6140 7100 178 427 2140 3270 101.0
38600 1180 5570 6420 175 385 1920 2950 99.8
34400 1030 4950 5660 173 342 1710 2610 99.8
27000 776 3880 4360 169 267 1330 2040 99.4
23000 620 3180 3570 164 214 1070 1640 96.4
18400 486 2550 2830 163 171 854 1300 96.3
35700 747 4210 4940 145 286 1640 2500 89.6
32900 661 3810 4450 142 258 1470 2260 88.5
29300 573 3380 3910 140 229 1310 2000 88.4
25100 486 2940 3350 139 200 1140 1740 89.3

Page 8
WCDIM

Torsion Warping
Constant Constant
ry J Iw
mm 103mm4 109mm6
30100 40400
25400 40400
19900 35700
13100 38800
8420 33300
6370 29400
3880 23000
24800 16300
19200 16200
14800 14300
10400 12500
5060 9380
3080 7310
1580 5720
16500 7100
12700 6230
8960 5400
5750 4600

Page 9
WCDES

Welded Columns - Properties for Assessing Section Capacity

Notes:
1. For BHP-300PLUS sections the tensile strength (fu) is 43
2. For Grade 400 sections the tensile strength (fu) is 480 M
3. C: Compact Section; N: Non-compact Section; S: Slende
4. BHP-300PLUS welded sections are produced to exceed

About x-axis About y-axis


BHP-300PLUS

Flange Web Form


Compact- Zex Compact- Zey
Designation fy fy Factor Designation
ness 103 mm3 ness 103 mm3
MPa MPa kf

500WC440 280 280 1.00 C 10400 C 5010


500WC414 280 280 1.00 C 10100 C 5010
500WC383 280 280 1.00 C 9130 C 4510
500WC340 280 280 1.00 C 8980 C 4000
500WC290 280 300 1.00 N 7570 N 3410
500WC267 280 300 1.00 N 6700 N 2970
500WC228 300 300 1.00 N 5210 N 2200
400WC361 280 280 1.00 C 7470 C 3210
400WC328 280 280 1.00 C 7100 C 3200
400WC303 280 280 1.00 C 6420 C 2880
400WC270 280 280 1.00 C 5660 C 2560
400WC212 280 300 1.00 N 4360 N 2000
400WC181 300 300 1.00 N 3410 N 1510
400WC144 300 300 1.00 N 2590 N 1120
350WC280 280 280 1.00 C 4940 C 2450
350WC258 280 280 1.00 C 4450 C 2210
350WC230 280 280 1.00 C 3910 C 1960
350WC197 280 300 1.00 C 3350 C 1720

Page 10
WCDES

ions the tensile strength (fu) is 430 MPa


the tensile strength (fu) is 480 MPa
Non-compact Section; S: Slender Section
sections are produced to exceed the minimum requirements of AS/NZS 3679.2-300.

About x-axis About y-axis


AS3679.2-400

Flange Web Form


Compact- Zex Compact- Zey
Designation fy fy Factor
ness 103 mm3 ness 103 mm3
MPa MPa kf

500WC440 360 360 1.000 C 10400 C 5010


500WC414 360 360 1.000 C 10100 C 5010
500WC383 360 360 1.000 C 9130 C 4510
500WC340 360 360 1.000 N 8830 N 3920
500WC290 360 380 1.000 N 7410 N 3310
500WC267 360 380 1.000 N 6540 N 2860
500WC228 380 380 0.964 S 4860 N 2100
400WC361 360 360 1.000 C 7470 C 3210
400WC328 360 360 1.000 C 7100 C 3200
400WC303 360 360 1.000 C 6420 C 2880
400WC270 360 360 1.000 C 5660 C 2560
400WC212 360 380 1.000 N 4270 N 1950
400WC181 380 380 1.000 N 3330 N 1460
400WC144 380 380 0.964 S 2410 N 1070
350WC280 360 360 1.000 C 4940 C 2450
350WC258 360 360 1.000 C 4450 C 2210
350WC230 360 360 1.000 C 3910 C 1960
350WC197 360 380 1.000 C 3350 C 1720

Page 11
UBDIM

Universal Beams - Dimensions and Properties

About x-axis About y-axis


Gross
Depth Depth Area of
of Flange Flange Web Root Between Cross Torsion Warping
Designation kg/m Section Width ThicknessThickness Radii Flanges Section Constant Constant
d bf tf tw r1 d1 (bf- Ag Ix Zx Sx rx Iy Zy Sy ry J Iw
mm mm mm mm mm mm d1 / tw tw)/2tf mm2 106mm4 103mm3 103mm3 mm 106mm4 103mm3 103mm3 mm 103mm4 109mm6
610UB125 125.0 612 229 19.6 11.9 14.0 572 48.1 5.54 16000 986.00 3230 3680 249.0 39.300 343.0 536.0 49.6 1560.0 3450.00
610UB113 113.0 607 228 17.3 11.2 14.0 572 51.1 6.27 14500 875.00 2880 3290 246.0 34.300 300.0 469.0 48.7 1140.0 2980.00
610UB101 101.0 602 228 14.8 10.6 14.0 572 54 7.34 13000 761.00 2530 2900 242.0 29.300 257.0 402.0 47.5 790.0 2530.00
530UB92.4 92.4 533 209 15.6 10.2 14.0 502 49.2 6.37 11800 554.00 2080 2370 217.0 23.800 228.0 355.0 44.9 775.0 1590.00
530UB82.0 82.0 528 209 13.2 9.6 14.0 502 52.3 7.55 10500 477.00 1810 2070 213.0 20.100 193.0 301.0 43.8 526.0 1330.00
460UB82.1 82.1 460 191 16.0 9.9 11.4 428 43.3 5.66 10500 372.00 1610 1840 188.0 18.600 195.0 303.0 42.2 701.0 919.00
460UB74.6 74.6 457 190 14.5 9.1 11.4 428 47.1 6.24 9520 335.00 1460 1660 188.0 16.600 175.0 271.0 41.8 530.0 815.00
460UB67.1 67.1 454 190 12.7 8.5 11.4 428 50.4 7.15 8580 296.00 1300 1480 186.0 14.500 153.0 238.0 41.2 378.0 708.00
410UB59.7 59.7 406 178 12.8 7.8 11.4 381 48.8 6.65 7640 216.00 1060 1200 168.0 12.100 135.0 209.0 39.7 337.0 467.00
410UB53.7 53.7 403 178 10.9 7.6 11.4 381 50.1 7.82 6890 188.00 933 1060 165.0 10.300 115.0 179.0 38.6 234.0 394.00
360UB56.7 56.7 359 172 13.0 8.0 11.4 333 41.6 6.31 7240 161.00 899 1010 149.0 11.000 128.0 198.0 39.0 338.0 330.00
360UB50.7 50.7 356 171 11.5 7.3 11.4 333 45.6 7.12 6470 142.00 798 897 148.0 9.600 112.0 173.0 38.5 241.0 284.00
360UB44.7 44.7 352 171 9.7 6.9 11.4 333 48.2 8.46 5720 121.00 689 777 146.0 8.100 94.7 146.0 37.6 161.0 237.00
310UB46.2 46.2 307 166 11.8 6.7 11.4 284 42.3 6.75 5930 100.00 654 729 130.0 9.010 109.0 166.0 39.0 233.0 197.00
310UB40.4 40.4 304 165 10.2 6.1 11.4 284 46.5 7.79 5210 86.40 569 633 129.0 7.650 92.7 142.0 38.3 157.0 165.00
310UB32.0 32.0 298 149 8.0 5.5 13.0 282 51.3 8.97 4080 63.20 424 475 124.0 4.420 59.3 91.8 32.9 86.5 92.90
250UB37.3 37.3 256 146 10.9 6.4 8.9 234 36.6 6.40 4750 55.70 435 486 108.0 5.660 77.5 119.0 34.5 158.0 85.20
250UB31.4 31.4 252 146 8.6 6.1 8.9 234 38.4 8.13 4010 44.50 354 397 105.0 4.470 61.2 94.2 33.4 89.3 65.90
250UB25.7 25.7 248 124 8.0 5.0 12.0 232 46.4 7.44 3270 35.40 285 319 104.0 2.550 41.1 63.6 27.9 67.4 36.70
200UB29.8 29.8 207 134 9.6 6.3 8.9 188 29.8 6.65 3820 29.10 281 316 87.3 3.860 57.5 88.4 31.8 105.0 37.60
200UB25.4 25.4 203 133 7.8 5.8 8.9 188 32.3 8.15 3230 23.60 232 260 85.4 3.060 46.1 70.9 30.8 62.7 29.20
200UB22.3 22.3 202 133 7.0 5.0 8.9 188 37.5 9.14 2870 21.00 208 231 85.5 2.750 41.3 63.4 31.0 45.0 26.00
200UB18.2 18.2 198 99 7.0 4.5 11.0 184 40.9 6.75 2320 15.80 160 180 82.6 1.140 23.0 35.7 22.1 38.6 10.40
180UB22.2 22.2 179 90 10.0 6.0 8.9 159 26.5 4.20 2820 15.30 171 195 73.6 1.220 27.1 42.3 20.8 81.6 8.71
180UB18.1 18.1 175 90 8.0 5.0 8.9 159 31.8 5.31 2300 12.10 139 157 72.6 0.975 21.7 33.7 20.6 44.8 6.80
180UB16.1 16.1 173 90 7.0 4.5 8.9 159 35.3 6.11 2040 10.60 123 138 72.0 0.853 19.0 29.4 20.4 31.5 5.88
150UB18.0 18.0 155 75 9.5 6.0 8.0 136 22.7 3.63 2300 9.05 117 135 62.8 0.672 17.9 28.2 17.1 60.5 3.56
150UB14.0 14.0 150 75 7.0 5.0 8.0 136 27.2 5.00 1780 6.66 88.8 102 61.1 0.495 13.2 20.8 16.6 28.1 2.53

Page 12
UBDES

Universal Beams - Properties for Design

Notes:
1. For BHP-300PLUS sections the tensile strength (fu) is 440 MPa
2. For Grade 350 sections the tensile strength (fu) is 480 MPa
3. C: Compact Section; N: Non-compact Section; S: Slender Section
4. BHP-300PLUS hot rolled sections are produced to exceed the minimum requirements of AS/NZS 3679.1-300.
5. BHP-300PLUS replaced Grade 250 as the base grade for these sections in 1994.

About x-axis About y-axis About x-axis About y-axis


BHP-300PLUS AS 3679.1-350

Flange Web Form Flange Web Form


Compact- Zex Compact- Zey Compact- Zex Compact- Zey
Designation fy fy Factor Designation fy fy Factor
ness 103 mm3 ness 103 mm3 ness 103 mm3 ness 103 mm3
MPa MPa kf MPa MPa kf
610UB125 280 300 0.950 C 3680 C 515.0 610UB125 340 340 0.916 C 3680 C 515.0
610UB113 280 300 0.926 C 3290 C 451.0 610UB113 340 340 0.891 C 3290 C 451.0
610UB102 300 320 0.888 C 2900 C 386.0 610UB102 340 360 0.867 C 2900 C 386.0
530UB92.4 300 320 0.928 C 2370 C 342.0 530UB92.4 340 360 0.907 C 2370 C 342.0
530UB82.0 300 320 0.902 C 2070 C 289.0 530UB82.0 340 360 0.880 C 2070 C 289.0
460UB82.1 300 320 0.979 C 1840 C 292.0 460UB82.1 340 360 0.956 C 1840 C 292.0
460UB74.6 300 320 0.948 C 1660 C 262.0 460UB74.6 340 360 0.926 C 1660 C 262.0
460UB67.1 300 320 0.922 C 1480 C 230.0 460UB67.1 340 360 0.901 C 1480 C 230.0
410UB59.7 300 320 0.938 C 1200 C 203.0 410UB59.7 340 360 0.918 C 1200 C 203.0
410UB53.7 320 320 0.913 C 1060 C 173.0 410UB53.7 360 360 0.894 N 1050 N 172.0
360UB56.7 300 320 0.996 C 1010 C 193.0 360UB56.7 340 360 0.974 C 1010 C 193.0
360UB50.7 300 320 0.963 C 897 C 168.0 360UB50.7 340 360 0.943 C 897 C 168.0
360UB44.7 320 320 0.930 N 770 N 140.0 360UB44.7 360 360 0.911 N 762 N 139.0
310UB46.2 300 320 0.991 C 729 C 163.0 310UB46.2 340 360 0.972 C 729 C 163.0
310UB40.4 320 320 0.952 C 633 C 139.0 310UB40.4 360 360 0.936 N 629 N 138.0
310UB32.0 320 320 0.915 N 467 N 86.9 310UB32.0 360 360 0.898 N 462 N 85.7
250UB37.3 320 320 1.000 C 486 C 116.0 250UB37.3 360 360 1.000 C 486 C 116.0
250UB31.4 320 320 1.000 N 395 N 91.4 250UB31.4 360 360 0.991 N 392 N 90.3
250UB25.7 320 320 0.949 C 319 C 61.7 250UB25.7 360 360 0.932 C 319 C 61.7
200UB29.8 320 320 1.000 C 316 C 86.3 200UB29.8 360 360 1.000 C 316 C 86.3
200UB25.4 320 320 1.000 N 259 N 68.8 200UB25.4 360 360 1.000 N 257 N 68.0
200UB22.3 320 320 1.000 N 227 N 60.3 200UB22.3 360 360 1.000 N 225 N 59.4
200UB18.2 320 320 0.990 C 180 C 34.4 200UB18.2 360 360 0.970 C 180 C 34.4
180UB22.2 320 320 1.000 C 195 C 40.7 180UB22.2 360 360 1.000 C 195 C 40.7
180UB18.1 320 320 1.000 C 157 C 32.5 180UB18.1 360 360 1.000 C 157 C 32.5
180UB16.1 320 320 1.000 C 138 C 28.4 180UB16.1 360 360 1.000 C 138 C 28.4
150UB18.0 320 320 1.000 C 135 C 26.9 150UB18.0 360 360 1.000 C 135 C 26.9
150UB14.0 320 320 1.000 C 102 C 19.8 150UB14.0 360 360 1.000 C 102 C 19.8

Page 13
UCDIM

Universal Columns - Dimensions and Properties

About x-axis About y-axis


Gross
Depth Depth Area of
of Flange Flange Web Root Between Cross Torsion Warping
Designation kg/m Section Width ThicknessThickness Radii Flanges Section Constant Constant
d bf tf tw r1 d1 (bf- Ag Ix Zx Sx rx Iy Zy Sy ry J Iw
mm mm mm mm mm mm d1 / tw tw)/2tf mm2 106mm4 103mm3 103mm3 mm 106mm4 103mm3 103mm3 mm 103mm4 109mm6
310UC96.8 96.8 308 305 15.4 9.9 16.5 277 28.0 9.58 12400 223.00 1450.0 1600.0 134.0 72.90 478.0 725.0 76.7 928.0 1560.0
310UC158 158.0 327 311 25.0 15.7 16.5 277 17.7 5.91 20100 388.00 2370.0 2680.0 139.0 125.00 807.0 1230.0 78.9 3810.0 2860.0
310UC137 137.0 321 309 21.7 13.8 16.5 277 20.1 6.80 17500 329.00 2050.0 2300.0 137.0 107.00 691.0 1050.0 78.2 2520.0 2390.0
310UC118 118.0 315 307 18.7 11.9 16.5 277 23.3 7.89 15000 277.00 1760.0 1960.0 136.0 90.20 588.0 893.0 77.5 1630.0 1980.0
250UC89.5 89.5 260 256 17.3 10.5 14.0 225 21.5 7.10 11400 143.00 1100.0 1230.0 112.0 48.40 378.0 575.0 65.2 1040.0 713.0
250UC72.9 72.9 254 254 14.2 8.6 14.0 225 26.2 8.64 9320 114.00 897.0 992.0 111.0 38.80 306.0 463.0 64.5 586.0 557.0
200UC59.3 59.3 210 205 14.2 9.3 11.4 181 19.5 6.89 7620 61.30 584.0 656.0 89.7 20.40 199.0 303.0 51.7 477.0 195.0
200UC52.2 52.2 206 204 12.5 8.0 11.4 181 22.7 7.84 6660 52.80 512.0 570.0 89.1 17.70 174.0 264.0 51.5 325.0 166.0
200UC46.2 46.2 203 203 11.0 7.3 11.4 181 24.8 8.90 5900 45.90 451.0 500.0 88.2 15.30 151.0 230.0 51.0 228.0 142.0
150UC37.2 37.2 162 154 11.5 8.1 8.9 139 17.1 6.34 4730 22.20 274.0 310.0 68.4 7.01 91.0 139.0 38.5 197.0 39.6
150UC30.0 30.0 158 153 9.4 6.6 8.9 139 21.0 7.79 3860 17.60 223.0 250.0 67.5 5.62 73.4 112.0 38.1 109.0 30.8
150UC23.4 23.4 152 152 6.8 6.1 8.9 139 22.8 10.70 2980 12.60 166.0 184.0 65.1 3.98 52.4 80.2 36.6 50.2 21.1
100UC14.8 14.8 97 99 7.0 5.0 10.0 83 16.6 6.71 1890 3.18 65.6 74.4 41.1 1.14 22.9 35.2 24.5 34.9 2.3

Page 14
UCDES

Universal Columns - Properties for Design

Notes:
1. For BHP-300PLUS sections the tensile strength (fu) is 440 MPa
2. For Grade 350 sections the tensile strength (fu) is 480 MPa
3. C: Compact Section; N: Non-compact Section; S: Slender Section
4. BHP-300PLUS hot rolled sections are produced to exceed the minimum requirements of AS/NZS 3679.1-300.
5. BHP-300PLUS replaced Grade 250 as the base grade for these sections in 1994.

About x-axis About y-axis About x-axis About y-axis


BHP-300PLUS AS 3679.1-350

Flange Web Form Flange Web Form


Compact- Zex Compact- Zey Compact- Zex Compact- Zey
Designation fy fy Factor Designation fy fy Factor
ness 103 mm3 ness 103 mm3 ness 103 mm3 ness 103 mm3
MPa MPa kf MPa MPa kf
310UC158 280 300 1 C 2680.0 C 1210.0 310UC158 340 340 1 C 2680.0 C 1210.0
310UC137 280 300 1 C 2300.0 C 1040.0 310UC137 340 340 1 C 2300.0 C 1040.0
310UC118 280 300 1 C 1960.0 C 882.0 310UC118 340 340 1 N 1950.0 N 878.0
310UC96.8 300 320 1 N 1560.0 N 694.0 310UC96.8 340 360 1 N 1550.0 N 684.0
250UC89.5 280 320 1 C 1230.0 C 567.0 250UC89.5 340 360 1 C 1230.0 C 567.0
250UC72.9 300 320 1 N 986.0 N 454.0 250UC72.9 340 360 1 N 977.0 N 448.0
200UC59.5 300 320 1 C 656.0 C 299.0 200UC59.5 340 360 1 C 656.0 C 299.0
200UC52.2 300 320 1 C 570.0 C 260.0 200UC52.2 340 360 1 N 569.0 N 260.0
200UC46.2 300 320 1 N 494.0 N 223.0 200UC46.2 340 360 1 N 490.0 N 220.0
150UC37.2 300 320 1 C 310.0 C 137.0 150UC37.2 340 360 1 C 310.0 C 137.0
150UC30.0 320 320 1 C 250.0 C 110.0 150UC30.0 360 360 1 N 248.0 N 109.0
150UC23.4 320 320 1 N 176.0 N 73.5 150UC23.4 360 360 1 N 174.0 N 72.3
100UC14.8 320 320 1 C 74.4 C 34.4 100UC14.8 360 360 1 C 74.4 C 34.4

Page 15
TFBDIM

Taper Flange Beams - Dimensions and Properties

Depth Depth
Designation kg/m of Flange Flange Web Between
Section Width Thickness Thickness Root Radii Toe Radii Flanges
d bf tf tw r1 r2 d1
mm mm mm mm mm mm mm
125TFB 13.1 125 65 8.5 5.0 8.0 4.0
100TFB 7.2 100 45 6.0 4.0 7.0 3.0

Page 16
TFBDIM

About x-axis About y

Depth
Between Gross Area of
Toe Radii Flanges Cross Section
r2 d1 Ag Ix Zx Sx rx Iy Zy
mm mm d1 / tw (bf-tw)/2tf mm2 106mm4 103mm3 103mm3 mm 106mm4 103mm3
108 21.6 3.53 1670 4.34 69.4 80.3 50.9 0.337
88 22.0 3.42 917 1.46 29.2 34.1 39.9 0.0795

Page 17
TFBDIM

About y-axis

Torsion Warping
Constant Constant
Iy Zy Sy ry J Iw
106mm4 103mm3 103mm3 mm 103mm4 109mm6
10.4 17.2 14.2 40.2 1.14
3.53 6.0 9.31 11.6 0.0176

Page 18
TFBDES

Taper Flange Channels - Properties for Assessing Section Capacity

Notes:
1. For BHP-300PLUS sections the tensile strength (fu) is
2. For Grade 350 sections the tensile strength (fu) is 480
3. C: Compact Section; N: Non-compact Section; S: Slen
4. BHP-300PLUS hot rolled sections are produced to exc
5. BHP-300PLUS replaced Grade 250 as the base grade

About x-axis About y-axis


BHP-300PLUS

Flange Web Form


Compact- Zex Compact- Zey
Designation fy fy Factor Designation
ness 103 mm3 ness 103 mm3
MPa MPa kf

125TFB 320 320 1 C 80.3 C 15.6


100TFB 320 320 1 C 34.1 C 5.3

Page 19
TFBDES

ons the tensile strength (fu) is 440 MPa


he tensile strength (fu) is 480 MPa
Non-compact Section; S: Slender Section
sections are produced to exceed the minimum requirements of AS/NZS 3679.1-300.
Grade 250 as the base grade for these sections in 1994.

About x-axis About y-axis


AS 3679.1-350

Flange Web Form


Compact- Zex Compact- Zey
Designation fy fy Factor
ness 103 mm3 ness 103 mm3
MPa MPa kf

125TFB 360 360 1 C 80.3 C 15.6


100TFB 360 360 1 C 34.1 C 5.3

Page 20
PFCDIM

Parallel Flange Channels - Dimensions and Properties

Depth Depth
Designation kg/m of Flange Flange Web Between
Section Width Thickness Thickness Root Radii Flanges
d bf tf tw r1 d1
mm mm mm mm mm mm d1 / tw
380PFC 55.2 380 100 17.5 10.0 14 345
300PFC 40.1 300 90 16.0 8.0 14 268
250PFC 35.5 250 90 15.0 8.0 12 220
230PFC 25.1 230 75 12.0 6.5 12 206
200PFC 22.9 200 75 12.0 6.0 12 176
180PFC 20.9 180 75 11.0 6.0 12 158
150PFC 17.7 150 75 9.5 6.0 10 131
125PFC 11.9 125 65 7.5 4.7 8 110
100PFC 8.31 100 50 6.7 4.2 8 86.6
75PFC 5.92 75 40 6.1 3.8 8 62.8

Page 21
PFCDIM

About x-axis

Depth
Between Gross Area of Coordinate of Coordinate of
Flanges Cross Section Centroid Shear Centre
d1 Ag XL X0 Ix Zx Sx rx Iy
mm d1 / tw (bf-tw)/2tf mm2 mm mm 106mm4 103mm3 103mm3 mm 106mm4
34.5 5.14 7030 27.5 56.7 152 798 946 147.0
33.5 5.13 5110 27.2 56.1 72.4 483 564 119.0
27.5 5.47 4520 28.6 58.5 45.1 361 421 99.9
31.7 5.71 3200 22.6 46.7 26.8 233 271 91.4
29.3 5.75 2920 24.4 50.5 19.1 191 221 80.9
26.3 6.27 2660 24.5 50.3 14.1 157 182 72.9
21.8 7.26 2250 24.9 51.0 8.34 111 129 60.8
23.4 8.04 1520 21.8 45.0 3.97 63.5 73 51.1
20.6 6.84 1060 16.7 33.9 1.74 34.7 40.3 40.4
16.5 5.94 754 13.7 27.2 0.683 18.2 21.4 30.1

Page 22
PFCDIM

About y-axis

Torsion Warping
Constant Constant
rx Iy ZyR ZyL Sy ry J Iw
mm 106mm4 103mm3 103mm3 103mm3 mm 103mm4 109mm6
6.48 89.4 236.0 161.0 30.4 472.0 151.00
4.04 64.4 148.0 117.0 28.1 290.0 58.20
3.64 59.3 127.0 107.0 28.4 238.0 35.90
1.76 33.6 77.8 61.0 23.5 108.0 15.00
1.65 32.7 67.8 58.9 23.8 101.0 10.60
1.51 29.9 61.5 53.8 23.8 81.4 7.82
1.29 25.7 51.6 46.0 23.9 54.9 4.59
0.658 15.2 30.2 27.2 20.8 23.1 1.64
0.267 8.01 16.0 14.4 15.9 13.2 0.424
0.12 4.56 8.71 8.2 12.6 8.13 0.106

Page 23
PFCDES

Parallel Flange Channels - Properties for Assessing Section Capacity

Notes:
1. For BHP-300PLUS sections the tensile strength (fu) is
2. For Grade 350 sections the tensile strength (fu) is 480
3. BHP-300PLUS hot rolled sections are produced to exc
4. BHP-300PLUS replaced Grade 250 as the base grade

About x-axis About y-axis


BHP-300PLUS

Flange Web Form


Designation fy fy Factor Load A Load B
MPa MPa kf Zex Zey Zey
103 mm3 103 mm3 103 mm3
380PFC 280 320 1 946 115 134
300PFC 300 320 1 564 82.3 96.6
250PFC 300 320 1 421 88.7 89.0
230PFC 300 320 1 271 45.1 50.4
200PFC 300 320 1 221 46.7 49.1
180PFC 300 320 1 182 44.8 44.8
150PFC 320 320 1 129 38.5 38.5
125PFC 320 320 1 72.8 22.8 22.8
100PFC 320 320 1 40.3 12.0 12.0
75PFC 320 320 1 21.4 6.84 6.84

Page 24
PFCDES

0PLUS sections the tensile strength (fu) is 440 MPa


50 sections the tensile strength (fu) is 480 MPa
US hot rolled sections are produced to exceed the minimum requirements of AS/NZS 3679.1-300.
US replaced Grade 250 as the base grade for these sections in 1994.

About x-axis About y-axis


AS 3679.1-350

Flange Web Form


Designation fy fy Factor Load A Load B
MPa MPa kf Zex Zey Zey
103 mm3 103 mm3 103 mm3
380PFC 340 360 1 946 104 134
300PFC 340 360 1 564 77.2 96.6
250PFC 340 360 1 421 84.9 89.0
230PFC 340 360 1 271 42.6 50.4
200PFC 340 360 1 221 44.5 49.1
180PFC 340 360 1 182 44.1 44.8
150PFC 360 360 1 129 38.5 38.5
125PFC 360 360 1 72 22.5 22.8
100PFC 360 360 1 40.3 12.0 12.0
75PFC 360 360 1 21.4 6.84 6.84

Page 25
UBPDIM

Universal Bearing Piles - Dimensions and Properties

About x-axis About y-axis


Gross
Depth Depth Area of
of Flange Flange Web Root Between Cross Torsion Warping
Designation kg/m Section Width ThicknessThickness Radii Flanges Section Constant Constant
d bf tf tw r1 d1 (bf- Ag Ix Zx Sx rx Iy Zy Sy ry J Iw
mm mm mm mm mm mm d1 / tw tw)/2tf mm2 106mm4 103mm3 103mm3 mm 106mm4 103mm3 103mm3 mm 103mm4 109mm6
310UBP78.8 78.8 299 306 11.1 11.1 16.5 277 24.9 13.30 10100 165.0 1100 1220 128.0 53.1 347 530 72.5 484 1100
310UBP149 149.0 318 316 20.7 20.5 16.5 277 13.5 7.14 19000 330.0 2080 2370 132.0 109.0 691 1070 75.8 2970 2410
310UBP110 110.0 308 310 15.4 15.3 16.5 277 18.1 9.57 14000 236.0 1530 1720 130.0 76.6 494 759 73.9 1240 1640
250UBP84.9 84.9 254 260 14.3 14.3 14.0 225 15.8 8.59 10800 123.0 965 1090 106.0 42.0 323 497 62.3 827 603
250UBP62.6 62.6 247 256 10.6 10.6 14.0 226 21.3 11.60 7990 88.1 713 795 105.0 29.7 232 355 60.9 345 415
200UBP146 146.0 245 218 32.0 25.0 11.4 181 7.2 3.02 18600 173.0 1410 1700 96.4 55.5 509 790 54.6 5980 630
200UBP122 122.0 230 220 25.0 25.0 11.4 180 7.2 3.90 15600 129.0 1120 1340 91.0 44.6 406 635 53.5 3540 469

Page 26
UBPDES

Universal Bearing Piles - Properties for Design

Notes:
1. For Grade 300PLUS sections the tensile stre
2. For Grade 350 sections the tensile strength
3. C: Compact Section; N: Non-compact Sectio
4. These sections are generally not stocked an
5. BHP-300PLUS hot rolled sections are produ
6. BHP-300PLUS replaced Grade 250 as the b

About x-axis About y-axis


BHP-300PLUS

Flange Web Form


Compact- Zex Compact- Zey
Designation fy fy Factor
ness 103 mm3 ness 103 mm3
MPa MPa kf

310UBP78.8 300 300 1 N 1130 N 460


310UBP149 280 280 1 C 2370 C 1040
310UBP110 300 300 1 N 1680 N 718
250UBP84.9 300 300 1 N 1080 N 480
250UBP62.6 320 320 1 N 747 N 318
200UBP146 280 280 1 C 1700 C 764
200UBP122 280 280 1 C 1340 C 609

Page 27
UBPDES

00PLUS sections the tensile strength (fu) is 440 MPa


50 sections the tensile strength (fu) is 480 MPa
Section; N: Non-compact Section; S: Slender Section
ons are generally not stocked and are available for project orders only subject to enquiry from your nearest BHP Steel Sales Office
US hot rolled sections are produced to exceed the minimum requirements of AS/NZS 3679.1-300.
US replaced Grade 250 as the base grade for these sections in 1994.

About x-axis About y-axis


AS 3679.1-350

Flange Web Form


Compact- Zex Compact- Zey
Designation fy fy Factor
ness 103 mm3 ness 103 mm3
MPa MPa kf

310UBP78.8 340 340 1 N 1110 N 450


310UBP149 340 340 1 C 2370 C 1040
310UBP110 340 340 1 N 1660 N 708
250UBP84.9 340 340 1 N 1070 N 474
250UBP62.6 360 360 1 N 738 N 312
200UBP146 340 340 1 C 1700 C 764
200UBP122 340 340 1 C 1340 C 609

Page 28
UBPDES

BHP Steel Sales Office

Page 29
EADIMXY

Equal Angles - x-axis and y-axis - Dimensions and Properties

Gross Coordinate of Centroid About x-axis About y-axis Torsion


Actual Area of Zx1=Zx Constan
Thickne Root Toe Cross Ix 4 Sx Iy Zy5 Zy3 Sy t
Designatio ss Radii Radii Section nL=pB nR=pT y1=y4 rx x5 x3 ry J
kg/m (b1-t)/t
n t r1 r2 Ag 106mm 103mm 103mm 106mm 103mm 103mm 103mm 103mm
mm mm mm mm2 mm mm 4 mm 4 3 mm 4 mm 3 mm 3 3 mm 4
200x200x26 76.80 26.0 18 5 6.69 9780 59.30 141.0 56.8000 141.0 402.000 643.00 76.20 14.90000 83.80 178.000 73.90 202.000 329.000 39.00 2250.000
200x200x20 60.10 20.0 18 5 9.00 7660 57.00 143.0 45.7000 141.0 323.000 511.00 77.20 11.80000 80.60 147.000 72.90 162.000 260.000 39.30 1060.000
200x200x18 54.40 18.0 18 5 10.10 6930 56.20 144.0 41.7000 141.0 295.000 464.00 77.60 10.80000 79.50 136.000 72.60 149.000 236.000 39.40 778.000
200x200x16 48.70 16.0 18 5 11.50 6200 55.40 145.0 37.6000 141.0 266.000 417.00 77.90 9.72000 78.40 124.000 72.30 135.000 212.000 39.60 554.000
200x200x13 40.00 13.0 18 5 14.40 5090 54.20 146.0 31.2000 141.0 221.000 344.00 78.30 8.08000 76.60 105.000 71.90 112.000 176.000 39.80 304.000
150x150x19 42.10 19.0 13 5 6.89 5360 44.20 106.0 17.6000 106.0 166.000 265.00 57.20 4.60000 62.60 73.500 54.90 83.800 135.000 29.30 657.000
150x150x16 35.40 15.8 13 5 8.49 4520 43.00 107.0 15.1000 106.0 142.000 225.00 57.80 3.91000 60.80 64.200 54.30 71.900 115.000 29.40 386.000
150x150x12 27.30 12.0 13 5 11.50 3480 41.50 108.0 11.9000 106.0 112.000 175.00 58.40 3.06000 58.70 52.100 53.70 56.900 89.300 29.60 174.000
150x150x10 21.90 9.5 13 5 14.80 2790 40.50 109.0 9.6100 106.0 90.600 141.00 58.70 2.48000 57.30 43.300 53.40 46.400 72.000 29.80 88.900
125x125x16 29.10 15.8 10 5 6.91 3710 36.80 88.2 8.4300 88.4 95.400 153.00 47.70 2.20000 52.10 42.300 45.40 48.500 77.800 24.40 313.000
125x125x12 22.50 12.0 10 5 9.42 2870 35.40 89.6 6.6900 88.4 75.700 120.00 48.30 1.73000 50.10 34.500 44.70 38.600 60.800 24.50 141.000
125x125x10 18.00 9.5 10 5 12.20 2300 34.40 90.6 5.4400 88.4 61.600 96.50 48.70 1.40000 48.70 28.800 44.40 31.500 49.000 24.70 71.900
125x125x8 14.90 7.8 10 5 15.00 1900 33.70 91.3 4.5500 88.4 51.500 80.20 48.90 1.17000 47.70 24.500 44.20 26.500 40.800 24.80 40.600
100x100x12 17.70 12.0 8 5 7.33 2260 29.20 70.8 3.2900 70.7 46.600 74.50 38.20 0.85700 41.30 20.800 35.80 23.900 37.900 19.50 110.000
100x100x10 14.20 9.5 8 5 9.53 1810 28.20 71.8 2.7000 70.7 38.200 60.40 38.60 0.69500 39.90 17.400 35.40 19.600 30.700 19.60 56.200
100x100x8 11.80 7.8 8 5 11.80 1500 27.50 72.5 2.2700 70.7 32.000 50.30 38.80 0.58200 38.90 14.900 35.20 16.500 25.600 19.70 31.700
100x100x6 9.16 6.0 8 5 15.70 1170 26.80 73.2 1.7800 70.7 25.200 39.30 39.10 0.45800 37.90 12.100 35.00 13.100 20.000 19.80 14.800
90x90x10 12.70 9.5 8 5 8.47 1620 25.70 64.3 1.9300 63.6 30.400 48.30 34.50 0.50000 36.40 13.800 31.90 15.700 24.600 17.60 50.500
90x90x8 10.60 7.8 8 5 10.50 1350 25.00 65.0 1.6300 63.6 25.600 40.40 34.80 0.41900 35.40 11.800 31.70 13.200 20.500 17.60 28.600
90x90x6 8.22 6.0 8 5 14.00 1050 24.30 65.7 1.2800 63.6 20.100 31.60 35.00 0.33000 34.30 9.620 31.50 10.500 16.100 17.80 13.400
75x75x10 10.50 9.5 8 5 6.89 1340 22.00 53.0 1.0800 53.0 20.400 32.80 28.40 0.28200 31.10 9.090 26.60 10.600 16.800 14.50 41.900
75x75x8 8.73 7.8 8 5 8.62 1110 21.30 53.7 0.9130 53.0 17.200 27.50 28.70 0.23700 30.10 7.870 26.40 8.990 14.000 14.60 23.800
75x75x6 6.81 6.0 8 5 11.50 867 20.50 54.5 0.7220 53.0 13.600 21.60 28.90 0.18700 29.00 6.440 26.20 7.150 11.000 14.70 11.200
75x75x5 5.27 4.6 8 5 15.30 672 19.90 55.1 0.5630 53.0 10.600 16.70 29.00 0.14700 28.10 5.220 26.10 5.620 8.610 14.80 5.280
65x65x10 9.02 9.5 6 3 5.84 1150 19.60 45.4 0.6910 46.0 15.000 24.30 24.50 0.18300 27.70 6.600 23.70 7.710 12.500 12.60 35.100
65x65x8 7.51 7.8 6 3 7.33 957 19.00 46.0 0.5890 46.0 12.800 20.50 24.80 0.15400 26.80 5.730 23.40 6.560 10.500 12.70 20.000
65x65x6 5.87 6.0 6 3 9.83 748 18.30 46.7 0.4710 46.0 10.200 16.20 25.10 0.12200 25.80 4.710 23.10 5.260 8.250 12.80 9.370
65x65x5 4.56 4.6 6 3 13.10 581 17.70 47.3 0.3710 46.0 8.080 12.70 25.30 0.09590 25.00 3.830 23.00 4.180 6.460 12.90 4.360
55x55x6 4.93 6.0 6 3 8.17 628 15.80 39.2 0.2780 38.9 7.140 11.40 21.00 0.07230 22.30 3.240 19.60 3.690 5.820 10.70 7.930
55x55x5 3.84 4.6 6 3 11.00 489 15.20 39.8 0.2200 38.9 5.660 8.93 21.20 0.05710 21.50 2.660 19.40 2.940 4.570 10.80 3.710
50x50x8 5.68 7.8 6 3 5.41 723 15.20 34.8 0.2530 35.4 7.160 11.70 18.70 0.06750 21.50 3.140 18.10 3.730 6.000 9.66 15.200
50x50x6 4.46 6.0 6 3 7.33 568 14.50 35.5 0.2050 35.4 5.790 9.30 19.00 0.05360 20.50 2.610 17.80 3.010 4.760 9.71 7.210
50x50x5 3.48 4.6 6 3 9.87 443 13.90 36.1 0.1630 35.4 4.610 7.32 19.20 0.04240 19.70 2.150 17.60 2.400 3.750 9.78 3.380
50x50x3 2.31 3.0 6 3 15.70 295 13.20 36.8 0.1100 35.4 3.110 4.90 19.30 0.02890 18.70 1.550 17.60 1.650 2.530 9.90 1.010
45x45x6 3.97 6.0 5 3 6.50 506 13.30 31.7 0.1460 31.8 4.590 7.41 17.00 0.03830 18.80 2.040 16.00 2.390 3.790 8.71 6.320
45x45x5 3.10 4.6 5 3 8.78 394 12.70 32.3 0.1170 31.8 3.660 5.84 17.20 0.03030 18.00 1.680 15.80 1.910 2.990 8.76 2.960
45x45x3 2.06 3.0 5 3 14.00 263 12.00 33.0 0.0790 31.8 2.480 3.92 17.30 0.02060 17.00 1.210 15.70 1.310 2.020 8.85 0.875
40x40x6 3.50 6.0 5 3 5.67 446 12.00 28.0 0.0997 28.3 3.530 5.75 15.00 0.02650 17.00 1.550 14.30 1.860 2.950 7.71 5.600
40x40x5 2.73 4.6 5 3 7.70 348 11.50 28.5 0.0801 28.3 2.830 4.55 15.20 0.02090 16.20 1.290 14.00 1.490 2.330 7.75 2.630
40x40x3 1.83 3.0 5 3 12.30 233 10.80 29.2 0.0545 28.3 1.930 3.06 15.30 0.01420 15.30 0.933 13.90 1.020 1.580 7.82 0.785
30x30x6 2.56 6.0 5 3 4.00 326 9.53 20.5 0.0387 21.2 1.830 3.06 10.90 0.01070 13.50 0.790 10.70 0.993 1.590 5.72 4.160
30x30x5 2.01 4.6 5 3 5.52 256 8.99 21.0 0.0316 21.2 1.490 2.45 11.10 0.00839 12.70 0.660 10.50 0.799 1.260 5.72 1.980
30x30x3 1.35 3.0 5 3 9.00 173 8.30 21.7 0.0218 21.2 1.030 1.67 11.20 0.00573 11.70 0.488 10.30 0.554 0.862 5.76 0.605
25x25x6 2.08 6.0 5 3 3.17 266 8.28 16.7 0.0210 17.7 1.190 2.03 8.89 0.00600 11.70 0.513 8.97 0.669 1.070 4.75 3.440
25x25x5 1.65 4.6 5 3 4.43 210 7.75 17.3 0.0173 17.7 0.980 1.65 9.07 0.00469 11.00 0.428 8.73 0.537 0.849 4.72 1.660
25x25x3 1.12 3.0 5 3 7.33 143 7.07 17.9 0.0121 17.7 0.685 1.13 9.22 0.00319 9.99 0.319 8.56 0.373 0.583 4.73 0.515

Page 30
EADIMNP

Equal Angles - n - axis and p - axis - Dimensions and Properties

About n-axis and p-axis

Designation Product of
2nd Moment
In=Ip nL=pB ZnB=ZpL nR=pT ZnT=ZpR Sn=Sp rn=rp of Area
Inp
106mm4 mm 103mm3 mm 103mm3 103mm3 mm 106mm4
200x200x26 35.80000 59.30 605.00 141.0 255.000 460.000 60.50 -20.90000
200x200x20 28.80000 57.00 505.00 143.0 201.000 363.000 61.30 -16.90000
200x200x18 26.30000 56.20 467.00 144.0 183.000 330.000 61.50 -15.50000
200x200x16 23.70000 55.40 427.00 145.0 164.000 296.000 61.80 -14.00000
200x200x13 19.70000 54.20 363.00 146.0 135.000 243.000 62.20 -11.60000
150x150x19 11.10000 44.20 250.00 106.0 105.000 189.000 45.40 -6.48000
150x150x16 9.48000 43.00 220.00 107.0 88.700 160.000 45.80 -5.58000
150x150x12 7.46000 41.50 180.00 108.0 68.800 124.000 46.30 -4.40000
150x150x10 6.04000 40.50 149.00 109.0 55.200 99.900 46.60 -3.56000
125x125x16 5.32000 36.80 144.00 88.2 60.300 109.000 37.90 -3.11000
125x125x12 4.21000 35.40 119.00 89.6 47.000 85.000 38.30 -2.48000
125x125x10 3.42000 34.40 99.40 90.6 37.800 68.400 38.60 -2.02000
125x125x8 2.86000 33.70 84.90 91.3 31.300 56.800 38.80 -1.69000
100x100x12 2.08000 29.20 71.10 70.8 29.300 53.200 30.30 -1.22000
100x100x10 1.70000 28.20 60.10 71.8 23.600 42.900 30.60 -1.00000
100x100x8 1.42000 27.50 51.70 72.5 19.600 35.700 30.80 -0.84200
100x100x6 1.12000 26.80 41.80 73.2 15.300 27.800 31.00 -0.66100
90x90x10 1.22000 25.70 47.30 64.3 18.900 34.400 27.40 -0.71600
90x90x8 1.02000 25.00 40.90 65.0 15.700 28.700 27.60 -0.60400
90x90x6 0.80500 24.30 33.20 65.7 12.300 22.400 27.70 -0.47500
75x75x10 0.68100 22.00 31.00 53.0 12.800 23.400 22.60 -0.39900
75x75x8 0.57500 21.30 27.00 53.7 10.700 19.600 22.70 -0.33800
75x75x6 0.45500 20.50 22.10 54.5 8.350 15.300 22.90 -0.26800
75x75x5 0.35500 19.90 17.90 55.1 6.440 11.800 23.00 -0.20800
65x65x10 0.43700 19.60 22.30 45.4 9.620 17.400 19.50 -0.25400
65x65x8 0.37100 19.00 19.60 46.0 8.070 14.600 19.70 -0.21800
65x65x6 0.29600 18.30 16.20 46.7 6.340 11.500 19.90 -0.17500
65x65x5 0.23400 17.70 13.20 47.3 4.940 8.970 20.10 -0.13800
55x55x6 0.17500 15.80 11.10 39.2 4.460 8.110 16.70 -0.10300

Page 31
EADIMNP

55x55x5 0.13900 15.20 9.12 39.8 3.480 6.340 16.80 -0.08140


50x50x8 0.16000 15.20 10.50 34.8 4.610 8.380 14.90 -0.09280
50x50x6 0.12900 14.50 8.90 35.5 3.640 6.630 15.10 -0.07560
50x50x5 0.10300 13.90 7.36 36.1 2.850 5.190 15.20 -0.06020
50x50x3 0.06940 13.20 5.25 36.8 1.890 3.460 15.30 -0.04050
45x45x6 0.09220 13.30 6.93 31.7 2.910 5.300 13.50 -0.05380
45x45x5 0.07340 12.70 5.76 32.3 2.280 4.160 13.60 -0.04310
45x45x3 0.04980 12.00 4.14 33.0 1.510 2.770 13.80 -0.02920
40x40x6 0.06310 12.00 5.24 28.0 2.260 4.120 11.90 -0.03660
40x40x5 0.05050 11.50 4.39 28.5 1.770 3.240 12.00 -0.02960
40x40x3 0.03440 10.80 3.19 29.2 1.180 2.170 12.20 -0.02010
30x30x6 0.02470 9.53 2.59 20.5 1.210 2.220 8.71 -0.01400
30x30x5 0.02000 8.99 2.22 21.0 0.951 1.760 8.83 -0.01160
30x30x3 0.01380 8.30 1.66 21.7 0.635 1.180 8.93 -0.00804
25x25x6 0.01350 8.28 1.63 16.7 0.807 1.490 7.13 -0.00750
25x25x5 0.01100 7.75 1.42 17.3 0.638 1.190 7.23 -0.00632
25x25x3 0.00765 7.07 1.08 17.9 0.426 0.802 7.33 -0.00445

Page 32
EADIMNP

Product of
2nd Moment
of Area
Inp
106mm4

Page 33
EADES

Equal Angles - x-axis and y-axis - Properties for Assessing Section Capacity

Notes:
1. For Grade 300PLUS sections the tensile strength (fu) is 440 MPa
2. For Grade 350 sections the tensile strength (fu) is 480 MPa
3. BHP-300PLUS hot rolled sections are produced to exceed the minimum requirem
4. BHP-300PLUS replaced Grade 250 as the base grade for these sections in 1994

About x-axis About y-axis


BHP-300PLUS AS 3679.1-350

fy Form
Designation Factor Load A or C Load B Load D Designation
MPa kf Zex Zey Zey
103 mm3 103 mm3 103 mm3
200x200x26 280 1.000 602.00 267.000 267.000 200x200x26
200x200x20 280 1.000 479.00 218.000 220.000 200x200x20
200x200x18 280 1.000 427.00 196.000 204.000 200x200x18
200x200x16 300 1.000 369.00 172.000 186.000 200x200x16
200x200x13 300 1.000 285.00 136.000 158.000 200x200x13
150x150x19 280 1.000 248.00 110.000 110.000 150x150x19
150x150x16 300 1.000 212.00 95.700 96.300 150x150x16
150x150x12 300 1.000 155.00 72.300 78.100 150x150x12
150x150x10 320 0.958 114.00 54.500 64.900 150x150x10
125x125x16 300 1.000 143.00 63.400 63.400 125x125x16
125x125x12 300 1.000 110.00 50.300 51.700 125x125x12
125x125x10 320 1.000 83.20 38.900 43.100 125x125x10
125x125x8 320 0.943 64.30 30.700 36.800 125x125x8
100x100x12 300 1.000 69.90 31.100 31.100 100x100x12
100x100x10 320 1.000 55.10 25.200 26.100 100x100x10
100x100x8 320 1.000 43.70 20.400 22.400 100x100x8
100x100x6 320 0.906 30.90 14.800 18.100 100x100x6
90x90x10 320 1.000 45.00 20.400 20.600 90x90x10
90x90x8 320 1.000 36.00 16.700 17.800 90x90x8
90x90x6 320 1.000 25.90 12.400 14.400 90x90x6
75x75x10 320 1.000 30.50 13.600 13.600 75x75x10
75x75x8 320 1.000 25.40 11.600 11.800 75x75x8
75x75x6 320 1.000 18.70 8.850 9.660 75x75x6
75x75x5 320 0.927 13.20 6.470 7.820 75x75x5
65x65x10 320 1.000 22.50 9.900 9.900 65x65x10
65x65x8 320 1.000 19.20 8.590 8.590 65x65x8
65x65x6 320 1.000 14.70 6.760 7.070 65x65x6
65x65x5 320 1.000 10.60 5.050 5.750 65x65x5
55x55x6 320 1.000 10.70 4.840 4.860 55x55x6
55x55x5 320 1.000 7.88 3.700 3.980 55x55x5
50x50x8 320 1.000 10.70 4.710 4.710 50x50x8
50x50x6 320 1.000 8.69 3.920 3.920 50x50x6

Page 34
EADES

50x50x5 320 1.000 6.60 3.080 3.220 50x50x5


50x50x3 320 0.907 3.82 1.900 2.320 50x50x3
45x45x6 320 1.000 6.88 3.060 3.060 45x45x6
45x45x5 320 1.000 5.39 2.470 2.520 45x45x5
45x45x3 320 1.000 3.19 1.550 1.810 45x45x3
40x40x6 320 1.000 5.29 2.330 2.330 40x40x6
40x40x5 320 1.000 4.25 1.930 1.930 40x40x5
40x40x3 320 1.000 2.59 1.250 1.400 40x40x3
30x30x6 320 1.000 2.74 1.190 1.190 30x30x6
30x30x5 320 1.000 2.23 0.990 0.990 30x30x5
30x30x3 320 1.000 1.50 0.714 0.732 30x30x3
25x25x6 320 1.000 1.78 0.769 0.769 25x25x6
25x25x5 320 1.000 1.47 0.642 0.642 25x25x5
25x25x3 320 1.000 1.03 0.479 0.479 25x25x3

Page 35
EADES

ngth (fu) is 440 MPa


u) is 480 MPa
ed to exceed the minimum requirements of AS/NZS 3679.1-300.
ase grade for these sections in 1994.

About x-axis About y-axis

fy Form
esignation Factor Load A or C Load B Load D
MPa kf Zex Zey Zey
103 mm3 103 mm3 103 mm3
340 1.000 602.00 267.000 267.000
340 1.000 469.00 214.000 220.000
340 1.000 417.00 192.000 204.000
340 1.000 362.00 169.000 186.000
340 0.956 278.00 132.000 158.000
340 1.000 248.00 110.000 110.000
340 1.000 209.00 94.500 96.300
340 1.000 152.00 70.900 78.100
360 0.906 111.00 53.100 64.900
340 1.000 143.00 63.400 63.400
340 1.000 109.00 49.600 51.700
360 1.000 81.60 38.100 43.100
360 0.892 62.70 29.900 36.800
340 1.000 69.90 31.100 31.100
360 1.000 54.40 24.800 26.100
360 1.000 42.90 20.000 22.400
360 0.856 30.00 14.400 18.100
360 1.000 44.50 20.100 20.600
360 1.000 35.40 16.400 17.800
360 0.954 25.30 12.100 14.400
360 1.000 30.50 13.600 13.600
360 1.000 25.10 11.500 11.800
360 1.000 18.40 8.700 9.660
360 0.876 12.80 6.300 7.820
360 1.000 22.50 9.900 9.900
360 1.000 19.20 8.590 8.590
360 1.000 14.50 6.660 7.070
360 1.000 10.40 4.940 5.750
360 1.000 10.50 4.780 4.860
360 1.000 7.75 3.640 3.980
360 1.000 10.70 4.710 4.710
360 1.000 8.69 3.920 3.920

Page 36
EADES

360 1.000 6.50 3.030 3.220


360 0.858 3.71 1.850 2.320
360 1.000 6.88 3.060 3.060
360 1.000 5.32 2.440 2.520
360 0.954 3.12 1.520 1.810
360 1.000 5.29 2.330 2.330
360 1.000 4.22 1.920 1.930
360 1.000 2.54 1.230 1.400
360 1.000 2.74 1.190 1.190
360 1.000 2.23 0.990 0.990
360 1.000 1.48 0.705 0.732
360 1.000 1.78 0.769 0.769
360 1.000 1.47 0.642 0.642
360 1.000 1.03 0.479 0.479

Page 37
UADIMXY

Unequal Angles - x-axis and y-axis - Dimensions and Properties

Gross
Area
of
Actual Cross Coordinate of Centroid About x-axis About y-axis

Thickn Root Toe Sectio Ix Zx1 Zx4 Zx5 Sx Iy Zy5 Zy3 Zy2 Sy J
Designati ess Radii Radii (b1- (b2- n pB nL y1 y4 y5 rx x5 x3 x2 ry
kg/m t r1 r2 Ag 106m 103m 103m 103m 103m 106m 103m 103m 103m 103m 103m Tan
on t)/t t)/t
mm mm mm mm2 mm mm m4 mm m3 mm m3 mm m3 m3 mm m4 mm m3 mm m3 mm m3 m3 mm m4 Alpha
150x100x12 22.50 12.0 10.0 5.0 11.50 7.33 2870 49.1 24.3 7.510 102.0 73.50 75.3 99.70 35.2 213.0 127.0 51.2 1.3500 42.0 32.10 52.9 25.50 27.6 48.80 51.70 21.7 141.00 0.438
150x100x10 18.00 9.5 10.0 5.0 14.80 9.53 2300 48.1 23.3 6.110 103.0 59.50 74.9 81.50 34.6 177.0 102.0 51.6 1.0900 40.7 26.90 53.0 20.60 26.9 40.70 41.80 21.8 71.90 0.441
150x90x16 27.90 15.8 10.0 5.0 8.49 4.70 3550 52.5 22.7 8.800 99.5 88.40 71.9 122.00 41.9 210.0 154.0 49.8 1.3200 38.9 34.00 49.9 26.50 24.6 53.80 55.90 19.3 300.00 0.353
150x90x12 21.60 12.0 10.0 5.0 11.50 6.50 2750 51.0 21.2 6.970 100.0 69.40 71.3 97.80 40.8 171.0 120.0 50.4 1.0400 37.2 28.00 50.1 20.80 23.4 44.50 43.80 19.5 136.00 0.360
150x90x10 17.30 9.5 10.0 5.0 14.80 8.47 2200 50.0 20.2 5.660 101.0 56.10 70.7 80.10 40.1 141.0 96.6 50.7 0.8470 36.1 23.50 50.4 16.80 22.6 37.40 35.40 19.6 69.00 0.363
150x90x8 14.30 7.8 10.0 5.0 18.20 10.50 1820 49.2 19.6 4.730 101.0 46.70 70.3 67.30 39.5 120.0 80.1 51.0 0.7100 35.2 20.20 50.6 14.00 22.1 32.20 29.50 19.7 39.00 0.364
125x75x12 17.70 12.0 8.0 5.0 9.42 5.25 2260 43.3 18.4 3.910 83.2 47.00 59.7 65.50 34.6 113.0 81.4 41.6 0.5850 31.9 18.40 41.4 14.10 19.9 29.30 29.70 16.1 110.00 0.356
125x75x10 14.20 9.5 8.0 5.0 12.20 6.89 1810 42.3 17.5 3.200 83.8 38.20 59.3 53.90 33.9 94.4 65.8 42.0 0.4760 30.7 15.50 41.6 11.40 19.2 24.90 24.10 16.2 56.20 0.360
125x75x8 11.80 7.8 8.0 5.0 15.00 8.62 1500 41.5 16.8 2.680 84.2 31.80 58.9 45.50 33.3 80.4 54.6 42.2 0.3990 29.9 13.30 41.8 9.55 18.6 21.50 20.10 16.3 31.70 0.363
125x75x6 9.16 6.0 8.0 5.0 19.80 11.50 1170 40.7 16.0 2.100 84.7 24.80 58.5 36.00 32.8 64.1 42.4 42.5 0.3150 29.0 10.80 42.1 7.47 18.0 17.50 15.70 16.4 14.80 0.364
100x75x10 12.40 9.5 8.0 5.0 9.53 6.89 1580 31.8 19.4 1.890 69.2 27.30 54.5 34.60 18.6 101.0 46.5 34.6 0.4010 32.2 12.50 36.4 11.00 22.3 18.00 21.20 16.0 49.10 0.546
100x75x8 10.30 7.8 8.0 5.0 11.80 8.62 1310 31.1 18.7 1.590 69.4 22.90 54.3 29.20 18.2 87.0 38.7 34.8 0.3370 31.3 10.70 36.4 9.26 21.8 15.40 17.80 16.0 27.80 0.549
100x75x6 7.98 6.0 8.0 5.0 15.70 11.50 1020 30.3 17.9 1.250 69.7 17.90 54.0 23.10 17.9 70.0 30.1 35.1 0.2650 30.3 8.75 36.5 7.27 21.4 12.40 13.90 16.2 13.00 0.551
75x50x8 7.23 7.8 7.0 3.0 8.62 5.41 921 25.2 12.8 0.586 50.8 11.50 37.8 15.50 18.0 32.5 20.0 25.2 0.1060 21.7 4.88 26.4 4.01 14.2 7.46 8.19 10.7 19.50 0.430
75x50x6 5.66 6.0 7.0 3.0 11.50 7.33 721 24.4 12.1 0.468 51.2 9.15 37.5 12.50 17.6 26.7 15.8 25.5 0.0842 20.8 4.04 26.5 3.18 13.6 6.17 6.48 10.8 9.21 0.435
75x50x5 4.40 4.6 7.0 3.0 15.30 9.87 560 23.8 11.5 0.370 51.5 7.17 37.2 9.93 17.2 21.5 12.3 25.7 0.0666 20.1 3.32 26.6 2.50 13.2 5.03 5.09 10.9 4.32 0.437
65x50x8 6.59 7.8 6.0 3.0 7.33 5.41 840 21.1 13.6 0.421 44.9 9.37 36.3 11.60 11.6 36.4 16.1 22.4 0.0936 22.3 4.20 23.9 3.91 15.6 6.00 7.49 10.6 17.60 0.570
65x50x6 5.16 6.0 6.0 3.0 9.83 7.33 658 20.4 12.9 0.338 45.2 7.48 36.1 9.35 11.2 30.2 12.7 22.7 0.0743 21.4 3.48 23.9 3.11 15.1 4.91 5.93 10.6 8.29 0.575
65x50x5 4.02 4.6 6.0 3.0 13.10 9.87 512 19.8 12.4 0.267 45.4 5.89 35.9 7.43 10.9 24.5 9.92 22.8 0.0587 20.6 2.85 23.9 2.46 14.8 3.97 4.66 10.7 3.87 0.577

Page 38
UADIMNP

Unequal Angles - n-axis and p-axis - Dimensions and Properties

About n-axis

150x100x12 6.520 49.1 133.0 101.0 64.60 117.0 47.7


150x100x10 5.290 48.1 110.0 102.0 51.90 94.0 48.0
150x90x16 7.970 52.5 152.0 97.5 81.70 145.0 47.4
150x90x12 6.290 51.0 123.0 99.0 63.50 114.0 47.8
150x90x10 5.100 50.0 102.0 100.0 51.00 91.5 48.2
150x90x8 4.260 49.2 86.6 101.0 42.30 76.0 48.4
125x75x12 3.540 43.3 81.8 81.7 43.30 77.3 39.6
125x75x10 2.880 42.3 68.2 82.7 34.90 62.5 39.9
125x75x8 2.410 41.5 58.1 83.5 28.90 52.0 40.1
125x75x6 1.890 40.7 46.5 84.3 22.50 40.6 40.3
100x75x10 1.550 31.8 48.6 68.2 22.60 41.3 31.3
100x75x8 1.300 31.1 41.8 68.9 18.80 34.4 31.5
100x75x6 1.020 30.3 33.7 69.7 14.60 26.9 31.7
75x50x8 0.511 25.2 20.3 49.8 10.30 18.5 23.6
75x50x6 0.407 24.4 16.7 50.6 8.05 14.6 23.8
75x50x5 0.321 23.8 13.5 51.2 6.27 11.4 23.9
65x50x8 0.341 21.1 16.2 43.9 7.75 14.1 20.1
65x50x6 0.272 20.4 13.4 44.6 6.10 11.1 20.3
65x50x5 0.215 19.8 10.9 45.2 4.75 8.7 20.5

Page 39
UADIMNP

About p-axis

2.340 24.3 96.20 75.7 30.90 56.00 28.6 -2.270


1.910 23.3 81.90 76.7 24.90 44.70 28.8 -1.850
2.150 22.7 94.90 67.3 32.00 59.50 24.6 -2.350
1.720 21.2 81.00 68.8 25.00 45.70 25.0 -1.890
1.410 20.2 69.50 69.8 20.20 36.50 25.3 -1.540
1.180 19.6 60.40 70.4 16.80 30.10 25.5 -1.300
0.958 18.4 52.00 56.6 16.90 31.40 20.6 -1.050
0.789 17.5 45.20 57.5 13.70 25.10 20.9 -0.867
0.664 16.8 39.60 58.2 11.40 20.70 21.0 -0.730
0.524 16.0 32.70 59.0 8.89 16.00 21.2 -0.575
0.743 19.4 38.30 55.6 13.40 24.30 21.7 -0.625
0.626 18.7 33.50 56.3 11.10 20.20 21.9 -0.527
0.494 17.9 27.50 57.1 8.67 15.70 22.0 -0.416
0.181 12.8 14.10 37.2 4.86 8.96 14.0 -0.174
0.145 12.1 12.00 37.9 3.84 6.98 14.2 -0.140
0.115 11.5 10.00 38.5 3.00 5.41 14.3 -0.111
0.174 13.6 12.70 36.4 4.78 8.74 14.4 -0.141
0.140 12.9 10.80 37.1 3.77 6.85 14.6 -0.114
0.111 12.4 8.96 37.6 2.95 5.32 14.7 -0.090

Page 40
UADES

Unequal Angles - Properties for Assessing Section Capacity

Notes:
1. For Grade 300PLUS sections the tensile strength (fu) is 440 MPa
2. For Grade 350 sections the tensile strength (fu) is 480 MPa
3. BHP-300PLUS hot rolled sections are produced to exceed the minimum requirem

About x-axis About y-axis


BHP-300PLUS AS 3679.1-350

150x100x12 300 1.000 102.00 110.00 35.30 38.20 150x100x12


150x100x10 320 0.975 74.80 81.70 26.00 30.90 150x100x10
150x90x16 300 1.000 132.00 133.00 39.50 39.80 150x90x16
150x90x12 300 1.000 96.30 104.00 28.80 31.10 150x90x12
150x90x10 320 0.973 70.60 81.80 21.20 25.20 150x90x10
150x90x8 320 0.863 53.10 60.30 15.90 21.00 150x90x8
125x75x12 300 1.000 68.60 70.50 20.60 21.20 125x75x12
125x75x10 320 1.000 51.60 57.20 15.50 17.20 125x75x10
125x75x8 320 0.964 39.80 46.00 11.90 14.30 125x75x8
125x75x6 320 0.824 26.80 30.10 8.07 11.20 125x75x6
100x75x10 320 1.000 39.40 40.90 15.90 16.60 100x75x10
100x75x8 320 1.000 31.20 33.10 12.60 13.90 100x75x8
100x75x6 320 0.946 22.00 21.80 8.93 10.90 100x75x6
75x50x8 320 1.000 17.00 17.30 5.93 6.02 75x50x8
75x50x6 320 1.000 12.60 13.70 4.37 4.77 75x50x6
75x50x5 320 0.956 8.89 9.65 3.10 3.75 75x50x5
65x50x8 320 1.000 14.10 14.10 5.86 5.86 65x50x8
65x50x6 320 1.000 10.70 11.20 4.46 4.67 65x50x6
65x50x5 320 1.000 7.76 7.92 3.23 3.68 65x50x5

Page 41
UADES

eed the minimum requirements of AS/NZS 3679.1-300.

About x-axis About y-axis

340 1.000 100.00 110.00 34.70 38.20


360 0.943 73.00 78.90 25.30 30.90
340 1.000 130.00 133.00 39.00 39.80
340 1.000 94.60 104.00 28.30 31.10
360 0.940 68.80 79.50 20.60 25.20
360 0.836 51.20 57.90 15.40 21.00
340 1.000 67.60 70.50 20.30 21.20
360 1.000 50.60 57.20 15.20 17.20
360 0.931 38.80 44.70 11.60 14.30
360 0.799 25.80 28.70 7.75 11.20
360 1.000 38.80 40.90 15.70 16.60
360 1.000 30.60 32.10 12.40 13.90
360 0.917 21.40 20.70 8.68 10.90
360 1.000 16.80 17.30 5.85 6.02
360 1.000 12.40 13.70 4.30 4.77
360 0.926 8.66 9.30 3.02 3.75
360 1.000 14.10 14.10 5.86 5.86
360 1.000 10.60 11.20 4.40 4.67
360 1.000 7.59 7.64 3.17 3.68

Page 42
RAILSDIM

Rails - Dimensions and Properties

RE 68 67.6 74.6 185.7 49.2 106.3 30.2 152.4 78.6


AS 60 61.0 70.0 170.0 49.0 93.0 28.0 146.0 74.5
AS 50 50.8 70.0 154.0 45.0 84.0 25.0 127.0 67.0
AS 41 40.7 63.5 136.5 40.5 74.6 21.4 127.0 60.3

Page 43
RAILSDIM

19.1 14.3 356.0 19.1 40 17.5 4 98.4 8614


20.0 15.0 300.0 20.0 20 16.5 4 79.1 7770
15.0 15.0 300.0 15.0 20 15.0 4 74.8 6470
9.5 11.0 305.0 19.5 INF 13.1 5 67.5 5187

Page 44
RAILSDIM

About x-axis

3136 2336 3142 39.5 391.7 463.8


2960 2040 2770 29.4 323.2 371.4
2680 1640 2150 20.1 254.1 269.3
2148 1110 1929 13.2 184.4 204.5

Page 45

Você também pode gostar