Escolar Documentos
Profissional Documentos
Cultura Documentos
Series
SDS1000X-E Series Digital Oscilloscope
Key Features
200 MHz bandwidth model
Real-time sampling rate up to 1 GSa/s
The newest generation of SPO technology
•Waveform capture rate up to 100,000 wfm/s (normal
mode), and 400,000 wfm/s (sequence mode)
•Supports 256-level intensity grading and color display
modes
•Record length up to 14 Mpts
•Digital trigger system
Product overview
Intelligent triggers: Edge, Slope, Pulse Width, Window,
SIGLENT’s new SDS1000X-E Series Super Phosphor Runt, Interval, Time out (Dropout), Pattern
Oscilloscope is available in one bandwidth, 200 MHz. It has Serial bus triggering and decoding (Standard), supports
a maximum sample rate of 1 GSa/s and a standard record IIC, SPI, UART, RS232, CAN, and LIN
length of 14 Mpts. For ease-of-use, the most commonly Video trigger, supports HDTV
used functions can be accessed with its user-friendly front
panel design.
scales
The SDS1000X-E series employs a new generation of SPO 10 types of one-button shortcuts, supports Auto Setup,
(Super Phosphor Oscilloscope) technology that provides Default, Cursors, Measure, Roll, History, Display/Persist,
Clear Sweep, Zoom and Print
is also lower than similar products in the industry. It comes Segmented acquisition (Sequence) mode, dividing the
with a minimum vertical input range of 500 uV/div, an maximum record length into multiple segments (up to
innovative digital trigger system with high sensitivity and 80,000), according to trigger conditions set by the user,
low jitter, and a waveform capture rate of 400,000 frames/ with a very small dead time segment to capture the
sec (sequence mode). The SDS1000X-E also employs a qualifying event
256-level intensity grading display function and a color
History waveform record (History) function, the maximum
temperature display mode not found in other models in
recorded waveform length is 80,000 frames
this class. Siglent’s latest oscilloscopes offering supports
multiple powerful triggering modes including serial bus Automatic measurement function for 38 parameters,
triggering. Decoding is standard configuration including supports Statist ics, Zoom measurement, Ga ti ng
IIC,SPI,UART,CAN,LIN. History waveform recording and measurement, Math measurement, History measurement
sequential triggering enable extended waveform recording and Ref measurement
and analysis. Another powerful addition is the new 1 million 1 Mpoints FFT
points FFT math function that gives the SDS1000X-E very True measurement and math of all sampled data points (to
high frequency resolution when observing signal spectra. 14M)
The new design also includes a hardware co-processor that
Math functions (FFT, addition, subtraction, multiplication,
delivers measurements quickly and accurately. The features
division, integration, differential, square root)
and performance of Siglent’s new SDS1000X-E cannot be
Preset key can be customized for user settings or factory
matched anywhere else in this price class.
“defaults”
Security Erase mode
High Speed hardware based Pass/Fail function
Large 7 inch TFT-LCD display with 800 * 480 resolution
Multiple interface types: USB Host, USB Device (USB-
TMC), LAN (VXI-11), Pass/Fail, Trigger Out
Supports SCPI remote control commands
Supports Multi-language display and embedded online
help
SDS1000X-E Series Digital Oscilloscope
Model SDS1202X-E
Channels 2+EXT
Waveform Capture Rate (Max.) 100,000 wfm/s (normal mode), 400,000 wfm/s (sequence mode)
Trigger Type Edge, Slope, Pulse Width, Window, Runt, Interval, Dropout, Pattern, Video
• Most commonly used functions are accessible using 10 different one-button operation keys: Auto Setup, Default, Cursor, Measure, Roll, History, Persist, Clear
Using hardware-based Zoom technologies and a record length of up to With a waveform capture rate of up to 400,000 wfm/s (sequence mode),
14 Mpts, users are able to use a higher sampling rate to capture more of the oscilloscope can easily capture the unusual or low-probability events.
the signal and then quickly zoom in to focus on the area of interest.
SPO display technology delivers fast refresh rates. The resulting intensity- The color temperature display is similar to the intensity-graded trace in
graded traces are brighter where events occur more frequently and less function, except that the trace occurrence is represented by different
bright where they occur less often. colors (color “temperature”) as opposed to changes in the intensity of
one color. Red represents the most common occurrences or probabilities,
while blue is used to mark points that occur least frequently.
SDS1000X-E displays the decoding through the events list. Bus protocol At any one timebase, the SDS1000X-E can measure using all 14M sample
information can be quickly and intuitively displayed in a tabular format. points. This ensures the accuracy of measurements while the math co-
processor decreases measurement time and increases ease-of-use.
SDS1000X-E Series Digital Oscilloscope
Playback the latest triggered events using the history function. Through Gate and Zoom measurement, the user can specify an arbitrary
Segmented memory zcquisition will store the waveform into multiple interval of waveform data analysis and statistics. This helps avoid
(up to 80,000) memory segments, each segment will store triggered measurement errors that can be caused by invalid or extraneous data,
waveforms and timestamp each frame.
The new math co-processor enables FFT analysis of incoming signals The SDS1000X-E utilizes a hardware-based Pass/Fail function, performing
using up to 1M samples per waveform. This provides high frequency up to 40,000 Pass / Fail decisions each second. Easily generate user-
resolution with a fast refresh rate. The FFT function also supports a
variety of window functions so that it can adapt to different spectrum for long-term signal monitoring or automated production line testing.
measurement needs.
The current parameters of oscilloscope can be preset to Default Key SDS1000X-E supports USB Host, USB Device (USB-TMC), LAN (VXI-11),
through the Save menu. Pass/Fail and Trigger Out
SDS1000X-E Series Digital Oscilloscope
Acquire System
Sampling Rate 1 GSa/s (Single - Channel), 500 MSa/s (Dual - Channel)
Input
Channels 2 Analog
Impedance
Probe attenuator 0.1X, 0.2X, 0.5X, 1X, 2X, 5X, 10X…… 1000X, 2000X, 5000X, 10000X
Vertical System
Bandwidth Limit
Bandwidth Flatness
(AC -3dB)
Noise
DC Gain Accuracy
Offset Accuracy
Horizontal System
Timebase Scale 1.0 ns/div - 100 s/div
Channel Skew
Waveform Capture Rate Up to 100,000 wfm/s (normal mode), 400,000 wfm/s (sequence mode)
Timebase Accuracy
Trigger System
Trigger Level
AC
DC
Trigger Coupling LFRJ
HFRJ
Noise RJ (CH1 - CH2)
Trigger Jitter
Trigger Displacement
Delay Trigger: 0 to 10,000 div
Edge Trigger
Slope Trigger
Limit Range , , ,
Source CH1/CH2
Resolution 1 ns
SDS1000X-E Series Digital Oscilloscope
Pulse Trigger
Limit Range , , ,
Resolution 1 ns
Video Trigger
1080i/60 Custom
Window Trigger
Interval Trigger
Limit Range , , ,
Source CH1/CH2
Resolution 1ns
Dropout Trigger
Resolution 1 ns
Runt Trigger
Limit Range , , ,
Resolution 1 ns
Pattern Trigger
Limit Range , , ,
Resolution 1 ns
SDS1000X-E Series Digital Oscilloscope
Serial Trigger
I2C Trigger
Condition Start, Stop, Restart, No Ack, EEPROM, 7 bits Address & Data, 10 bits Address & Data, Data Length
Limit Range
EEPROM: 1 byte
Data Length Addr & Data: 1 - 2 byte
Data Length: 1 - 12 byte
SPI Trigger
Condition Data
Bit Value 0, 1, X
Limit Range
CAN Trigger
Source CH 1, CH 2
LIN Trigger
ID 1 byte
Serial Decoder
I2C Decoder
List 1 - 7 lines
SPI Decoder
List 1 - 7 lines
Signal RX, TX
List 1 - 7 lines
CAN Decoder
List 1 - 7 lines
LIN Decoder
Ver1.3, Ver2.0
List 1 - 7 lines
SDS1000X-E Series Digital Oscilloscope
Measurement
Ampl Difference between top and base in a bimodal signal, or between max and min in an unimodal signal
Cmean
Cstd
Crms
Period
Freq
+Wid
-Wid
Rise Time
Fall Time
Horizontal Time
Bwid
crossing
Delay
Time@Level
FRR
FRF
FFR
FFF
LRR
LRF
LFR
LFF
Cursors
Track: Time X1, X2, (X1-X2)
Math Function
Operation
Number of Decoders 2
I/O
Standard USB Host, USB Device, LAN, Pass/Fail, Trigger Out
Display (Screen)
Display Type 7-inch TFT LCD
Range 8 x 14 divisions
Display (Waveform)
Display Mode Dot, Vector
Persist Time
Language
Environments
Temperature Operating: 10 - +40
Humidity , 24 hours
, 24 hours
Height
Safety 2006 / 95 / EC
Power Supply
Input Voltage 100 - 240 VAC, CAT II, Auto selection
Frequency 50 / 60 / 400 Hz
Power 25 W Max
Mechanical
Length: 312 mm
Height: 150 mm
battery source
Bandwidth: 150 KHz, Max. continuous current: 70 Arms, Peak current: 200 A
CP4070
CP4070A Bandwidth: 300 KHz, Max. continuous current: 70 Arms, Peak current: 200 A
Current Probe
CP5030
Bandwidth: 50 MHz, Max. continuous current: 30 Arms, Peak current: 50 A
Bandwidth: 12 MHz, Max. continuous current: 150 Arms, Peak current: 300 A
CP5150
Bandwidth: 5 MHz, Max. continuous current: 500 Arms, Peak current: 750A
CP5500
Differential Probe
Bandwidth: 40 MHz
HPB4010 Differential Range: DC 10 KV, AC (rms): 7 KV (sine), AC (Vpp): 20 KV (Pulse)
High Voltage
1000 X
The USB Device interface allows a connection into the GPIB interface. USB-
GPIB adapter allows the oscilloscope to easily send and receive commands
Isolated front end ISFE
IEEE488.2 standard.
Output signals include square waves, sine, AM, fast edge , pulse, PWM, I2C,
Demo Board STB-3
CAN, LIN etc. Used in teaching and demonstrations.
SDS1000X-E Series Digital Oscilloscope
Ordering information
SDS1000X-E Series Digital Oscilloscope
Product Name
SDS1202X-E 200 MHz Two Channels
USB Cable -1
Quick Start -1
Passive Probe -2
Standard Accessories
Power Cord -1
DPB4080/DPB5150/DPB5150A
Differential Probe
/DPB5700/DPB5700A