Escolar Documentos
Profissional Documentos
Cultura Documentos
com
( )Preliminary Specifications
Ϡ)Final Specifications
(Ϡ
Kelly Kao
_________________________________ ____________________________________
Eugene CC Chen
____________________________________
Reviewed By Project Leader
Greg Hsiung
____________________________________
Prepared By PM
Hubert Liu
____________________________________
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Contents
No
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
3 ELECTRICAL SPECIFICATION
4 OPTICAL SPECIFICATION
5 MECHANICAL CHARACTERISTICS
7 INTERNATIONAL STANDARD
7-1 SAFETY
7-2 EMC
8 PACKING
9 PRECAUTION
9-5 STORAGE
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Record of Revision
Version Date Page Description
0.1 2011/12/07 First release
0.2 2012/01/12 20 Update Surface Luminance (White)
1.0 2012/02/09 6 Update DC Characteristic
24 Update front view
25 Update back view
1.1 2012/02/16 16 Update Striking Voltage
1.2 2012/03/02 24 Update front view
25 Update back view
1.3 2012/03/07 6 Update BLU power consumption
16 Update BL Total Power Dissipation
16 Update striking voltage
1.4 2012/03/27 16 Update striking voltage
24 Update front view
25 Update back view
1.5 2012/04/19 16 Update PWM Dimming Duty Ratio
19 Update Power Sequence for Backlight
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
1. General Description
This specification applies to the 32.0 inch Color TFT-LCD Module T320XVN02.0. This LCD module has a TFT
active matrix type liquid crystal panel 1,366x768 pixels, and diagonal size of 32.0 inch. This module supports
1,366x768 mode. Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in
horizontal stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for
each dot.
The T320XVN02.0 has been designed to apply the 8-bit 1 channel LVDS interface method. It is intended to
support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very
important.
* General Information
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
3. Electrical Specification
The T320XVN02.0 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT
array and liquid crystal. The other is to power Back Light Unit.
3.1.1: DC Characteristics
Value
Parameter Symbol Unit Note
Min. Typ. Max
LCD
Power Supply Input Voltage VDD 10.8 12 13.2 VDC
Power Supply Input Current IDD -- 0.39 0.44 A 1
Power Consumption PC -- 4.68 5.28 Watt 1
Inrush Current IRUSH -- -- 3 A 2
Permissible Ripple of Power Supply Input Voltage VRP -- -- VDD * 5% mVpk-pk 3
LVDS Differential Input High Threshold Voltage VTH +100 -- +300 mVDC 4
Interface
Differential Input Low Threshold Voltage VTL -300 -- -100 mVDC 4
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
3.1.2: AC Characteristics
Value
Parameter Symbol Unit Note
Min. Typ. Max
Receiver Clock : Spread Spectrum Fclk Fclk
Fclk_ssʳ --ʳ MHzʳ 7
Modulation range ʳ -3%ʳ +3%ʳ
Receiver Clock : Spread Spectrum
LVDS Fssʳ 30ʳ --ʳ 200ʳ KHzʳ 7
Modulation frequencyʳ
Interface
Receiver Data Input Margin
Fclk = 85 MHz tRMGʳ -0.4 --ʳ 0.4 nsʳ 8
Fclk = 65 MHzʳ -0.5ʳ --ʳ 0.5ʳ
Note :
1. Test Condition:
(1) VDD = 12.0V
(2) Fv = 60Hz,
(3) Fclk= Max freq.
(4) Temperature = 25 к
(5) Typ. Input current : White Pattern
Max. Input current: Heavy loading pattern defined by AUO
*1'
μs
3. Test Condition:
(1) The measure point of VRP is in LCM side after connecting the System Board and LCM.
(2) Under Max. Input current spec. condition.
4. VICM = 1.25V
LVDS -
V IC M V TH
|V ID |
V TL
LVDS +
GND
|V ID |
0V
|V ID |
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Note: x = 0, 1, 2, 3, 4
7. LVDS Receiver Clock SSCG (Spread spectrum clock generator) is defined as below figures
)66
)FONB
)FONBVV
VVPD[
PD[
)FON
)FONB
)FONBVV
VVPLQ
PLQ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
W5,3
W5,3
W5,3
W5,3
W5,3
W5,3
W5,3
/9'65[
5[ 5[ 5[ 5[ 5[ 5[ 5[ 5[ 5[ 5[ 5[ 5[
,QSXW'DWD
/9'65[
,QSXW&ORFN 9GLII
9
)FON 7
9. Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting tape,
TFT-LCD Module have a low luminance and the inverter has abnormal action because leakage current
occurs between lamp wire and conducting tape.
10. The relative humidity must not exceed 80% non-condensing at temperatures of 40 к or less. At
temperatures greater than 40 к, the wet bulb temperature must not exceed 39к. When operate at low
temperatures, the brightness of CCFL will drop and the life time of CCFL will be reduced.
11. Specified values are for a single lamp only which is aligned horizontally. The lifetime is defined as the time
which luminance of the lamp is 50% compared to its original value.
[Operating condition: Continuous operating at Ta = 25±2 к]
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
ÎNS
LVDS Option = High/OpenÎ
& OR FN
& + [B 5 5 * 5 5 5 5 5 5 *
& + [B
& + [B * * % % * * * * * %
& + [B
& + [B
& + [B % % '( 1$ 1$ % % % % '(
& + [B
& + [B 5 5 1$ % % * * 5 5 1$
Note: x = 1, 2, 3, 4…
ÎJEIDA
LVDS Option = LowÎ
3 UH YLR X V & \F OH & X UUHQ W& \FOH 1 H [ W& \FOH
& OR FN
&+ [B 5 5 * 5 5 5 5 5 5 *
&+ [B
&+ [B * * % % * * * * * %
&+ [B
G7
&+ [B
% % '( 1$ 1$ % % % % '(
&+ [B
&+ [B
&+ [B 5 5 1$ % % * * 5 5 1$
Note: x = 1, 2, 3, 4…
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Notes:
(1) Display position is specific by the rise of DE signal only.
st st
Horizontal display position is specified by the rising edge of 1 DCLK after the rise of 1 DE, is displayed on the
left edge of the screen.
(2)Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight times of
st st
horizontal period. The 1 data corresponding to one horizontal line after the rise of 1 DE is displayed at the top
line of screen.
(3)If a period of DE “High” is less than 1366 DCLK or less than 768 lines, the rest of the screen displays black.
(4)The display position does not fit to the screen if a period of DE “High” and the effective data period do not
synchronize with each other.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
&+
'(
&/.
'(
'DWD
5*%
3L[HO
0
/LQH
3L[HO
0
1
3L[HO
0
7FON
3L[HO
0
,QYDOLG'DWD
7EONY
,QYDOLG'DWD
/LQH
3L[HO
7K
3L[HO
7Y
/LQH
3L[HO
3L[HO
/LQH
7GLVSK
7K
3L[HO
7GLVSY
3L[HO
/LQH
3L[HO
0
3L[HO
0
3L[HO
0
/LQH
1
7EONK
,QYDOLG'DWD
,QYDOLG'DWD
1 / LQ H
0SL[HO
3L[HO
3L[HO
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
W W W W W
W W
%DFNOLJKWRQ RII
FRQWUROVLJQDO
9%/2 1 *1'
&0 2 6,QWHUIDFH6LJQDO W W
/9' 6 B 6( /
* 1'
Values
Parameter Unit
Min. Type. Max.
t1 0.4ʳ ---ʳ 30ʳ ms
t2 0.1ʳ ---ʳ 50ʳʳ ms
t3 450ʳʳ ---ʳ ---ʳ ms
*1
t4 0 ʳ ---ʳ ---ʳ ms
t5 0ʳ ---ʳ ---ʳ ms
*2
t6 ---ʳ ---ʳ --- ʳ ms
t7 500ʳ ---ʳ ---ʳ ms
*3
t8ʳ 10 ʳ ---ʳ 50ʳ msʳ
t9ʳ 0ʳ ---ʳ ---ʳ msʳ
Note:
(1) t4=0 : concern for residual pattern before BLU turn off.
(2) t6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)
(3) When CMOS Interface signal is N.C. (no connection), opened in Transmitted end, t8 timing spec can be
negligible.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
VBL+
Operating Voltage 24 V sine wave Vrms
VBL-
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Input Interface
CN1 : CI0112M1HRL-NH (Cvilux)_Normal
1 +VBL
2 +VBL
AC 24 V
3 +VBL
(According to T-BB Designed output Voltage)
4 -VBL
5 -VBL
6 -VBL
7 S_GND Signal GND
8 VCC Power Supply For Protection Circuit
9 CNT_PRT Open Connector Protection
10 LD Protection Signal (Lamp Detection)
11 FB1 Lamp Current Feedback Signal 1
12 FB2 Lamp Current Feedback Signal 2
Output Interface
CN1~N : Metal Holder_CPLDTD41PP0 (Cvilux)
Pin Symbol Description
N VH High Voltage
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
к
The above characteristics are measured under the conditions:
Ambient temperature: 25±2 , Relative Humidity: 65±20%RH.
Κ Δ
The inverter type of the measurement KODA Frequency 55KHz. Κ
Κ Κ
VL measuring is operated by NF[As-129]. Test mode: C.C.
Test conditions Frequency 55KHz
Κ
IL Basis of the setting lamp current of the above characteristics.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Value
Parameter Units
Min Typ Max
T1 0 - - ms
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a
dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface at a
viewing angle of ij and ș equal to 0°.
Fig.1 presents additional information concerning the measurement equipment and method.
SR3 or equivalent
Values
Parameter Symbol Unit Notes
Min. Typ. Max
Contrast Ratio CR 2400 3000 -- 1
2
Surface Luminance (White) LWH 280 350 -- cd/m 2
Luminance Variation įWHITE(9P) -- -- 1.33 3
Response Time (G to G) TȖ -- 6.5 -- ms 4
Color Gamut NTSC 72 %
Color Coordinates
Red RX 0.640
RY 0.330
Green GX 0.290
GY 0.600
Typ.-0.03 Typ.+0.03
Blue BX 0.150
BY 0.060
White WX 0.280
WY 0.290
Viewing Angle 5
x axis, right(ij=0°) șr -- 89 -- degree
x axis, left(ij=180°) șl -- 89 -- degree
y axis, up(ij=90°) șu -- 89 -- degree
y axis, down (ij=270°) șd -- 89 -- degree
Note:
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
2. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels
displaying white. From more information see FIG 2. When lamp current IH = 15mA. LWH=Lon5 where Lon5 is
the luminance with all pixels displaying white at center 5 location.
3. The variation in surface luminance, įWHITE is defined (center of Screen) as:
įWHITE(9P)= Maximum(Lon1, Lon2,…,Lon9)/ Minimum(Lon1, Lon2,…Lon9)
4. Response time 7 ӫʳ is the average time required for display transition by switching the input signal for five
luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on Fv=60Hz to optimize.
Measured Target
Response Time 0% 25% 50% 75% 100%
0% 0% to 25% 0% to 50% 0% to 75% 0% to 100%
25% 25% to 0% 25% to 50% 25% to 75% 25% to 100%
Start 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100%
75% 75% to 0% 75% to 25% 75% to 50% 75% to 100%
100% 100% to 0% 100% to 25% 100% to 50% 100% to 75%
ӫ
7 is determined by 10% to 90% brightness difference of rising or falling period. (As illustrated)
The response time is defined as the following figure and shall be measured by switching the input signal for
“any level of grey(bright) “ and “any level of gray(dark)”.
Any level of gray (Bright) Any level of gray (Dark) Any level of gray (Bright)
0%, 25%, 50%, 75%, 100% 0%, 25%, 50%, 75%, 100%
Photodetector
Output
T ӫ (F) T ӫ (R)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
FIG. 2 Luminance
H/2 1 2 3
4 5 6 H
7 8
H/6
V/6 V/2
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For
more information see FIG3.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T320XVN02.0. In addition the figures in the
next page are detailed mechanical drawing of the LCD.
Horizontal 760.0 mm
Vertical 450.0 mm
Weight 5,000 g
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Front View
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Back View
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
7. International Standard
7.1 Safety
(1) UL 60950-1, UL 60065; Standard for Safety of Information Technology Equipment Including
electrical Business Equipment.
(2) IEC 60950-1 : 2001, IEC 60065:2001 ; Standard for Safety of International Electrotechnical
Commission
(3) EN 60950 : 2001+A11, EN 60065:2002+A1:2006; European Committee for Electrotechnical
Standardization (CENELEC), EUROPEAN STANDARD for Safety of Information Technology
Equipment Including Electrical Business Equipment.
7.2 EMC
(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),
1992
(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC),
1998
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
8. Packing
8-1 DEFINITION OF LABEL:
A. Panel Label:
*xxxxxxxxxxxx-xxxx*
AU Optronics
(2) For RoHs compatible products, AUO will add RoHS for identification.
Note: The green Mark will be present only when the green documents have been ready by AUO internal green
team. (definition of green design follows the AUO green design checklist.)
B. Carton Label:
QTY : 4
7;91
;;;;;;;;;;
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Protect Film
Creped Paper Tape Anti-Static Bag (Blue)
Panel placement
direction in carton.
( 4 ) Pcs Modules
Cushion Set
"H" Tape
( 4 ) Pcs / 1 Carton
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Specification
Item Packing Remark
Qty. Dimension Total Weight (kg)
Box = 1.85kg
Packing BOX 4pcs/box 834(L)*374(W)*548(H) 22.61kg
Cushion = 0.76kg
Stretch film
Corner angle
Pallet
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
12. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
(2) You should consider the mounting structure so that uneven force (ex. twisted stress) is not applied
to module. And the case on which a module is mounted should have sufficient strength so that
external force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit
broken by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the
surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials
like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the
adhesives used to attach front/ rear polarizer. Do not use acetone, toluene and alcohol because
they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5 к and 35к at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they
be stored in the container in which they were shipped.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com