Escolar Documentos
Profissional Documentos
Cultura Documentos
Check
Valves
MODEL DESCRIPTION FLOW CAVITY PAGE NO.
1 4
PDCV-08 PILOT OPERATED DUAL CHECK 5 GPM C0840 1-151.0
POCD-08 replaced by PDCV-08
POCD-10 10 GPM C1040 1-132.0
2 3
C1 C2
DPOC-08 DUAL PILOT OPERATED CHECK 10 GPM C0825 1-141.0
DPOC-10 18 GPM C1025 1-142.0
DPOC-12 36 GPM C1225 1-143.0
V1 V2
Reference: 520-P-010000-EN-01/02.2016
CVFP-08
TORQUE:
Steel = 35/40 Ft-Lb. [47/54 Nm]
Aluminum = 25/30 Ft-Lb. [34/41 Nm]
.85"
[21,6]
1.88"
[47,8]
1.10" 1
1.88"
[27,9]
[47,8]
CVFP-08-X-X-XXX
L/M (28,5 cSt)
015 = 15 PSI
SEALS 030 = 30 PSI 14
060 = 60 PSI 200
N = BUNA "N"
V = VITON 120 = 120 PSI
150 10,5
PORTS
0 = CARTRIDGE ONLY 7,0
100
02BX = G 1/4" BSPP
06TX = SAE - #6 3,5
50
"A" - ALUM. HOUSING
"S" - STEEL HOUSING 0 BAR
2 4 6 8 10
PSI
G.P.M.(135 SUS)
Reference: 520-P-010110-EN-00/09.2015
CVFP-08
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic check valve, for use as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 1 to port 2 and blocks
flow from port 2 to port 1 or holding a load.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 10.0 GPM [38 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-0821 Buna "N"
SKV-0821 Viton
WEIGHT: .20 lb [.12 kg] cartridge only.
VALVE CAVITY: #C0820, See Page 0-011.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010110-EN-00/09.2015
CVFP-10
TORQUE:
Steel = 55/60 Ft-Lb. [74/81 Nm]
Aluminum = 35/40 Ft-Lb. [47/54 Nm]
.800"
[20,3]
2.00"
[50,8]
1.28"
[32,5]
2
2.00" 1
[50,8]
BASIC
P)
015 = 15 PSI
SEALS 030 = 30 PSI
N = BUNA "N" 060 = 60 PSI
120 = 120 PSI 100
V = VITON 7,0
PORTS
0 = CARTRIDGE ONLY
02BX = G 1/4" BSPP
03BX = G 3/8" BSPP 50 3,5
06TX = SAE - #6
08TX = SAE - #8
Reference: 520-P-010120-EN-00/09.2015
CVFP-10
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic check valve, for use as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 1 to port 2 and blocks
flow from port 2 to port 1 or holding a load.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 18.0 GPM [68 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1021 Buna "N"
SKV-1021 Viton
WEIGHT: .25 lb [.12 kg] cartridge only.
VALVE CAVITY: #C1020, See Page 0-012.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010120-EN-00/09.2015
CVFP-12
TORQUE:
Steel = 70/75 Ft-Lb. [95/102 Nm]
Aluminum = 55/60 Ft-Lb. [74/81 Nm]
1.13"
[28,7]
2.75" 1.75"
[69,9] [44,5]
2
2.75"
[69,9]
BASIC
P)
015 = 15 PSI
SEALS 030 = 30 PSI
N = BUNA "N" 060 = 60 PSI
V = VITON 120 = 120 PSI 100 7,0
PORTS
0 = CARTRIDGE ONLY
04BX = G 1/2" BSPP
06BX = G 3/4" BSPP 50 3,5
10TX = SAE - #10
12TX = SAE - #12
Reference: 520-P-010130-EN-00/09.2015
CVFP-12
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic check valve, for use as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 1 to port 2 and blocks
flow from port 2 to port 1 or holding a load.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 36.0 GPM [136 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1231 Buna "N"
SKV-1231 Viton
WEIGHT: 0.50 lb [0.22 kg] cartridge only.
VALVE CAVITY: #C1220, See Page 0-013.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010130-EN-00/09.2015
CVFP-16
TORQUE:
Steel = 95/100 Ft-Lb. [129/136 Nm]
Aluminum = 70/75 Ft-Lb. [95/102 Nm]
1.35"
[34,3]
3.00"
[76,2]
1.82"
[46,2]
2
3.00"
[76,2]
BASIC
P)
015 = 15 PSI
SEALS 030 = 30 PSI
N = BUNA "N" 060 = 60 PSI
V = VITON 120 = 120 PSI 100 7,0
PORTS
0 = CARTRIDGE ONLY
06BX = G 3/4" BSPP
08BX = G 1.0" BSPP 50 3,5
12TX = SAE - #12
16TX = SAE - #16
Reference: 520-P-010140-EN-00/09.2015
CVFP-16
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic check valve, for use as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 1 to port 2 and blocks
flow from port 2 to port 1 or holding a load.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 60.0 GPM [228 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1621 Buna "N"
SKV-1621 Viton
WEIGHT: 0.86 lb [0.39 kg] cartridge only.
VALVE CAVITY: #C1620, See Page 0-014.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010140-EN-00/09.2015
CVRP-08
TORQUE:
Steel = 35/40 Ft-Lb. [47/54 Nm]
Aluminum = 25/30 Ft-Lb. [34/41 Nm]
.850"
[21,5]
1.88"
[47,62] 1.10"
[27,96]
2
1
.140" .312"
1.88"
[3,5] [7,9]
[47,62]
NOTE: CAVITY BOTTOM HOLE MUST ALLOW FOR POPPET EXTENSION (.438 DIA.)
PORTS 7,0
100
0 = CARTRIDGE ONLY
02BX = G 1/4" BSPP 50 3,5
06TX = SAE - #6
0 BAR
"A" - ALUM. HOUSING
"S" - STEEL HOUSING 2 4 6 8 10
PSI
G.P.M.(135 SUS)
Reference: 520-P-010210-EN-00/09.2015
CVRP-08
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic check valve, for use as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 2 to port 1 and blocks
flow from port 1 to port 2 or holding a load.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 10.0 GPM [38 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-0821 Buna "N"
SKV-0821 Viton
WEIGHT: .20 lb [.12 kg] cartridge only.
VALVE CAVITY: #C0820, See Page 0-011.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010210-EN-00/09.2015
CVRP-10
TORQUE:
Steel = 55/60 Ft-Lb. [74/81 Nm]
Aluminum = 35/40 Ft-Lb. [47/54 Nm]
.80"
[20,3]
2.00"
[50,8]
1.28"
[32,5]
2
2.00" 1
[50,8] .15" [3,8]
NOTE: CAVITY BOTTOM HOLE MUST ALLOW FOR POPPET EXTENSION (.570" DIA.)
FOR ALUMINUM OR STEEL VALVE HOUSING CONFIGURATIONS SEE PAGE 0-012.1
BASIC
P)
015 = 15 PSI
SEALS 030 = 30 PSI
N = BUNA "N" 060 = 60 PSI
V = VITON 120 = 120 PSI 100 7,0
PORTS
0 = CARTRIDGE ONLY
02BX = G 1/4" BSPP
03BX = G 3/4" BSPP 50 3,5
06TX = SAE - #10
08TX = SAE - #12
Reference: 520-P-010220-EN-01/01.2016
CVRP-10
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic check valve, used as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 2 to port 1 and blocks
flow from port 1 to port 2 or holding a load.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 18.0 GPM [68 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1021 Buna "N"
SKV-1021 Viton
WEIGHT: .25 lb [.12 kg] cartridge only.
VALVE CAVITY: #C1020, See Page 0-012.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010220-EN-01/01.2016
CVRP-12
TORQUE:
Steel = 70/75 Ft-Lb. [95/102 Nm]
Aluminum = 55/60 Ft-Lb. [74/81 Nm]
1.13"
[28,7]
2.75"
[69,9]
1.75"
[44,5]
2
2.75" 1
.22" [5,6]
[69,9]
NOTE: CAVITY BOTTOM HOLE MUST ALLOW FOR POPPET EXTENSION (.750" DIA.)
FOR ALUMINUM OR STEEL VALVE HOUSING CONFIGURATIONS SEE PAGE 0-013.1
BASIC
P)
015 = 15 PSI
SEALS 030 = 30 PSI
N = BUNA "N" 060 = 60 PSI
V = VITON 120 = 120 PSI 100 7,0
PORTS
0 = CARTRIDGE ONLY
04BX = G 1/2" BSPP
06BX = G 3/4" BSPP 50 3,5
10TX = SAE - #10
12TX = SAE - #12
Reference: 520-P-010230-EN-00/09.2015
CVRP-12
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic check valve, used as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 2 to port 1 and blocks
flow from port 1 to port 2 or holding a load.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 36.0 GPM [136 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1221 Buna "N"
SKV-1221 Viton
WEIGHT: 0.50 lb [0.22 kg] cartridge only.
VALVE CAVITY: #C1220, See Page 0-013.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010230-EN-00/09.2015
CVRP-16
TORQUE:
Steel = 95/100 Ft-Lb. [129/136 Nm]
Aluminum = 70/75 Ft-Lb. [95/102 Nm]
1.35"
[34,3]
3.00"
[76,2]
1.82"
[46,2]
2
1
3.00"
[76,2] .28" [7,1]
015 = 15 PSI
SEALS 030 = 30 PSI
N = BUNA "N" 060 = 60 PSI
V = VITON 120 = 120 PSI
100 7,0
PORTS
0 = CARTRIDGE ONLY
04BX = G 1/2" BSPP
06BX = G 3/4" BSPP 50 3,5
10TX = SAE - #10
12TX = SAE - #12
Reference: 520-P-010240-EN-00/09.2015
CVRP-16
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic check valve, used as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 2 to port 1 and blocks
flow from port 1 to port 2 or holding a load.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 50.0 GPM [190 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1621 Buna "N"
SKV-1621 Viton
WEIGHT: 0.82 lb [0.37 kg] cartridge only.
VALVE CAVITY: #C1620, See Page 0-014.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010240-EN-00/09.2015
CVFB-04
.56"
[14,2]
.188"
[4,8]
HEX.
.100"
[2,54]
.93"
[23,6]
BASIC
PORTS 50 3,5
0 = CARTRIDGE ONLY
(NO HOUSING OFFERED)
25 1,8
PSI BAR
0 0.5 1.0 1.5 2.0 2.5 3.0
G.P.M.(135 SUS)
Reference: 520-P-010300-EN-00/09.2015
CVFB-04
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided ball,
hydraulic check valve, for use as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 1 to port 2 and blocks
flow from port 2 to port 1 or holding a load.
All external carbon steel parts are plated for longer life against the elements.
All cartridge valves are 100% functionally tested.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 2.5 GPM [9,5 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-0421 Buna "N"
SKV-0421 Viton
WEIGHT: .08 lb [.04 kg] cartridge only.
VALVE CAVITY: #C0420.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010300-EN-00/09.2015
CVFB-08
TORQUE:
Steel = 35/40 Ft-Lb. [47/54 Nm]
Aluminum = 25/30 Ft-Lb. [34/41 Nm]
.478
[12,1]
1.88"
[47,8]
1.88" 1.100
1
[47,8] [27,9]
CVFB-08-X-X-XXX
L/M (28,5 cSt)
010 = 10 PSI
SEALS 025 = 25 PSI 14
050 = 50 PSI 160
N = BUNA "N"
V = VITON
120 10,5
PORTS
0 = CARTRIDGE ONLY 7,0
80
02BX = G 1/4" BSPP
06TX = SAE - #6 3,5
40
"A" - ALUM. HOUSING
"S" - STEEL HOUSING 0 BAR
2 4 6 8 10
PSI
G.P.M.(135 SUS)
Reference: 520-P-010310-EN-00/09.2015
CVFB-08
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided ball,
hydraulic check valve, for use as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 1 to port 2 and blocks
flow from port 2 to port 1 or holding a load.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 10.0 GPM [38 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-0821 Buna "N"
SKV-0821 Viton
WEIGHT: .20 lb [.12 kg] cartridge only.
VALVE CAVITY: #C0820, See Page 0-011.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010310-EN-00/09.2015
CVFB-10
TORQUE:
Steel = 55/60 Ft-Lb. [74/81 Nm]
Aluminum = 35/40 Ft-Lb. [47/54 Nm]
.558"
[14,2]
2.00"
[50,8]
1.28"
[32,5]
2
2.00" 1
[50,8]
BASIC
P)
015 = 15 PSI
SEALS 030 = 30 PSI
N = BUNA "N" 060 = 60 PSI
V = VITON 120 = 120 PSI 100 7,0
PORTS
0 = CARTRIDGE ONLY
02BX = G 1/4" BSPP
03BX = G 3/4" BSPP 50 3,5
06TX = SAE - #10
08TX = SAE - #12
Reference: 520-P-010320-EN-01/01.2016
CVFB-10
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided ball,
hydraulic check valve, for use as a blocking or load holding
device for high pressure applications.
OPERATIONS
This valve allows free flow from port 1 to port 2 and blocks
flow from port 2 to port 1 for holding a load.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 18.0 GPM [68 l/m] nominal. See performance chart.
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1021 Buna "N"
SKV-1021 Viton
WEIGHT: .25 lb [.12 kg] cartridge only.
VALVE CAVITY: #C1020, See Page 0-012.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-010320-EN-01/01.2016
POCI-08
PILOT OPERATED CHECK VALVE POPPET TYPE, 2 1
PILOT TO OPEN, 3 TO 1 PILOT RATIO 3
TORQUE:
Steel = 35/40 Ft-Lb. [47/54 Nm]
Aluminum = 25/30 Ft-Lb. [34/41 Nm]
1.00"
[25,4]
HEX
.88"
[22,4]
3
2.50"
[63,5] 1.60"
[40,6]
2
.15"
[3,8] .312"
2.25" [7,9]
[57,2]
NOTE: CAVITY BOTTOM HOLE MUST ALLOW FOR POPPET EXTENSION (.500 DIA.).
FOR ALUMINUM OR STEEL VALVE HOUSING CONFIGURATIONS SEE PAGE 0-021-1.
SIZE
CRACK PRESSURE 60
08 = 3/4"-16 UNF 150 10,5
PRESSURE DROP (
010 = 10 PSI
SEALS 030 = 30 PSI
060 = 60 PSI
N = BUNA "N" 30
V = VITON 100 7,0
ADJUSTMENT
PORTS
10
F = FIXED
50 3,5
0 = CARTRIDGE ONLY
03BX = G 3/8" BSPP
08TX = SAE - #8
0 BAR
"A" - ALUM. HOUSING 2 4 6 8 10
PSI
"S" - STEEL HOUSING
G.P.M.(135 SUS)
Reference: 520-P-011010-EN-00/09.2015
POCI-08
PILOT OPERATED CHECK VALVE POPPET TYPE,
PILOT TO OPEN, 3 TO 1 PILOT RATIO.
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic pilot operated check valve, for use as a blocking
or load holding device for high pressure applications.
OPERATIONS
This valve allows free flow from port 2 to port 1 and blocks
flow from port 1 to port 2 or holding a load. Flow will be allowed
from port 1 to port 2 when pressure is applied to port 3.
This pilot operated check valve has a 3 to 1 pilot ratio, meaning
that it takes at least one-third of the load pressure held at port 1
that is required at port 3 to open the valve.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 10.0 GPM [38 l/m] nominal. See performance chart.
PILOT RATIO: 3 TO 1
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-0828 Buna "N"
SKV-0828 Viton
WEIGHT: .26 lb [.12 kg] cartridge only.
VALVE CAVITY: #C0825, See Page 0-021.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-011010-EN-00/09.2015
POCI-10
PILOT OPERATED CHECK VALVE POPPET TYPE, 2 1
PILOT TO OPEN, 3 TO 1 PILOT RATIO. 3
TORQUE:
Steel = 55/60 Ft-Lb. [74/81 Nm]
Aluminum = 35/40 Ft-Lb. [47/54 Nm]
1.06"
[27,0]
HEX
"F" FIXED
1.63"
[42,3]
.795"
[20,2]
2.75"
[69,8]
3
1.85"
[46,9]
2
.15" [3,8]
2.50" 1
[63,5]
NOTE: CAVITY BOTTOM HOLE MUST ALLOW FOR POPPET EXTENSIONS (.563 DIA.)
FOR ALUMINUM OR STEEL VALVE HOUSING CONFIGURATIONS SEE PAGE 0-022-1.
L/M (28,5 cSt)
POCI-10-X-X-X-XXX 19 38 57 76
250 17,0
BASIC
200 13,6
P)
SIZE
10 = 7/8"-14 UNF CRACK PRESSURE
010 = 10 PSI
PRESSURE DROP (
Reference: 520-P-011020-EN-00/09.2015
POCI-10
PILOT OPERATED CHECK VALVE
POPPET TYPE, PILOT TO OPEN, 3 TO 1 PILOT RATIO.
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic pilot operated check valve, for use as a blocking
or load holding device for high pressure applications.
OPERATIONS
This valve allows free flow from port 2 to port 1 and blocks
flow from port 1 to port 2 or holding a load. Flow will be allowed
from port 1 to port 2 when pressure is applied to port 3.
This pilot operated check valve has a 3 to 1 pilot ratio, meaning
that it takes at least one-third of the load pressure held at port 1
that is required at port 3 to open the valve.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 18.0 GPM [70 l/m] nominal. See performance chart.
PILOT RATIO: 3 TO 1
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1028 Buna "N"
SKV-1028 Viton
WEIGHT: .39 lb [.18 kg] cartridge only.
VALVE CAVITY: #C1025, See Page 0-022.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-011020-EN-00/09.2015
POCI-12
PILOT OPERATED CHECK VALVE POPPET TYPE, 2 1
"F" FIXED
1.99"
[50,5]
1.13"
[28,6]
3.50"
[88,9]
3
2.45"
[62,2]
2
.19" [4,8]
3.00" 1
[76,2]
NOTE: CAVITY BOTTOM HOLE MUST ALLOW FOR POPPET EXTENSION (.750 DIA.).
FOR ALUMINUM OR STEEL VALVE HOUSING CONFIGURATIONS SEE PAGE 0-023-1.
L/M (28,5 cSt)
POCI-12-X-X-X-XXX
19 38 57 76 94 114 132
250 17,0
BASIC
200 13,6
P)
SIZE
12 = 1.062"-12 UNF CRACK PRESSURE
010 = 10 PSI
PRESSURE DROP (
Reference: 520-P-011030-EN-00/09.2015
POCI-12
PILOT OPERATED CHECK VALVE
POPPET TYPE, PILOT TO OPEN, 3 TO 1 PILOT RATIO.
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic pilot operated check valve, for use as a blocking
or load holding device for high pressure applications.
OPERATIONS
This valve allows free flow from port 2 to port 1 and blocks flow
from port 1 to port 2 or holding a load. Flow will be allowed from
port 1 to port 2 when sufficient pilot pressure is applied to port 3.
This pilot operated check valve has a 3 to 1 pilot ratio, meaning
that it takes at least one-third of the load pressure held at port 1
that is required at port 3 to open the valve.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 35.0 GPM [132.4 l/m] nominal. See performance chart.
PILOT RATIO: 3 TO 1
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1228 Buna "N"
SKV-1228 Viton
WEIGHT: 0.63 lb [0,25 kg] cartridge only.
VALVE CAVITY: #C1225, See Page 0-023.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-011030-EN-00/09.2015
POCX-08
PILOT OPERATED CHECK VALVE POPPET TYPE, 2 1
PILOT TO OPEN, 3 TO 1 PILOT RATIO.
P
TORQUE:
Steel = 35/40 Ft-Lb. [47/54 Nm]
Aluminum = 25/30 Ft-Lb. [34/41 Nm]
1.00"
[25,4]
HEX
1.75"
[44,45]
1.88"
[47,75]
1.10"
[27,94] 2
1.88" .140"
[4,0] .312"
[47,75] [7,9]
NOTE: CAVITY BOTTOM HOLE MUST ALLOW FOR POPPET EXTENSION (.500 DIA.).
FOR ALUMINUM OR STEEL VALVE HOUSING CONFIGURATIONS SEE PAGE 0-011.1
SIZE
PRESSURE DROP (
PORTS
0 = CARTRIDGE ONLY "P" PILOT PORT 3,5
50
02BX = G 1/4" BSPP 4T = SAE - #4
06TX = SAE - #6
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic pilot operated check valve, for use as a blocking
or load holding device for high pressure applications.
OPERATIONS
This valve allows free flow from port 2 to port 1 and blocks
flow from port 1 to port 2 or holding a load. Flow will be allowed
from port 1 to port 2 when pressure is applied to pilot port "P".
This pilot operated check valve has a 3 to 1 pilot ratio, meaning
that it takes at least one-third of the load pressure held at port 1
that is required at pilot port "P" to open the valve.
We recommend to use an orifice to dampen the pilot signal (X) when used
with an on/off (hard shifting) valve.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 10.0 GPM [38,0 l/m] nominal. See performance chart.
PILOT RATIO: 3 TO 1
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-0821 Buna "N"
SKV-0821 Viton
WEIGHT: .34 lb [.15 kg] cartridge only.
VALVE CAVITY: #C0820, See Page 0-011.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
1.06"
[27,0]
1.70"
[43,2]
1.28"
[32,5]
2
NOTE: CAVITY BOTTOM HOLE MUST ALLOW FOR POPPET EXTENSION (.563 DIA.).
FOR ALUMINUM OR STEEL VALVE HOUSING CONFIGURATIONS SEE PAGE 0-012.1
L/M (28,5 cSt)
POCX-10-X-X-XX-XXX 19 38 57 76
200 14,0
120
BASIC
P)
030 = 30 PSI
SEALS 060 = 60 PSI 60
120 = 120 PSI
N = BUNA "N"
100 7,0
V = VITON
30
PORTS
0 = CARTRIDGE ONLY "P" PILOT PORT
02BX = G 1/4" BSPP 2B = G 1/4" BSPP 50 3,5
03BX = G 3/8" BSPP 4T = SAE - #4
06TX = SAE - #6
08TX = SAE - #8
PSI BAR
"A" - ALUM. HOUSING
"S" - STEEL HOUSING 0 5 10 15 20
G.P.M.(135 SUS)
Reference: 520-P-011120-EN-00/09.2015
POCX-10
PILOT OPERATED CHECK VALVE
POPPET TYPE, PILOT TO OPEN, 3 TO 1 PILOT RATIO.
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic pilot operated check valve, for use as a blocking
or load holding device for high pressure applications.
OPERATIONS
This valve allows free flow from port 2 to port 1 and blocks
flow from port 1 to port 2 or holding a load. Flow will be allowed
from port 1 to port 2 when pressure is applied to pilot port "P".
This pilot operated check valve has a 3 to 1 pilot ratio, meaning
that it takes at least one-third of the load pressure held at port 1
that is required at pilot port "P" to open the valve.
We recommend to use an orifice to dampen the pilot signal (X) when used
with an on/off (hard shifting) valve.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-011120-EN-00/09.2015
POCX-12
PILOT OPERATED CHECK VALVE POPPET TYPE, 2 1
PILOT TO OPEN, 3 TO 1 PILOT RATIO.
P
TORQUE:
Steel = 70/75 Ft-Lb. [95/102 Nm]
Aluminum = 55/60 Ft-Lb. [74/81 Nm]
1.31"
[33,4]
HEX
2.15"
[54,6]
2.75"
[69,9]
1.75"
[44,5]
2
NOTE: CAVITY BOTTOM HOLE MUST ALLOW FOR POPPET EXTENSION(.630 DIA.).
FOR ALUMINUM OR STEEL VALVE HOUSING CONFIGURATIONS SEE PAGE 0-013.1
L/M (28,5 cSt)
POCX-12-X-X-XX-XXX 38 76 114 151
200 14,0
BASIC
120
P)
12 = 1.062"-12 UNF
030 = 30 PSI
SEALS 060 = 60 PSI 60
120 = 120 PSI
N = BUNA "N"
100 7,0
V = VITON
30
PORTS
0 = CARTRIDGE ONLY "P" PILOT PORT
04BX = G 1/2" BSPP 2B = G 1/4" BSPP 50 3,5
06BX = G 3/4" BSPP 4T = SAE - #4
10TX = SAE - #10
12TX = SAE - #12
PSI BAR
"A" - ALUM. HOUSING
"S" - STEEL HOUSING 0 10 20 30 40
G.P.M.(135 SUS)
Reference: 520-P-011130-EN-00/09.2015
POCX-12
PILOT OPERATED CHECK VALVE
POPPET TYPE, PILOT TO OPEN, 3 TO 1 PILOT RATIO.
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic pilot operated check valve, for use as a blocking
or load holding device for high pressure applications.
OPERATIONS
This valve allows free flow from port 2 to port 1 and blocks flow
from port 1 to port 2 or holding a load. Flow will be allowed from
port 1 to port 2 when sufficient pilot pressure is applied to port "P".
This pilot operated check valve has a 3 to 1 pilot ratio, meaning
that it takes at least one-third of the load pressure held at port 1
that is required at pilot port "P" to open the valve.
We recommend to use an orifice to dampen the pilot signal (X) when used
with an on/off (hard shifting) valve.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-011130-EN-00/09.2015
Dual P.O. Check Valve Cartridges, SAE 08 / NG 5
Qmax = 5 gpm (19 l/min),pmax = 3600psi (250 bar)
Pilot Operated
Series PDCV-08…
1 Description
The PDCV08… series dual pilot operated check valve sensed at port 3 or flow is allowed from port 4 to port 3 when
cartridges are SAE 08 / NG 5, high performance screwin pilot pressure is sensed at port 2. In order to pilot the valve
valves with a 3/416 UNF mounting thread. This unit is a opens, the pressure at port 2 or port 3 needs to exceed one-
cartridge type, high strength steel guided poppet for third of the load pressure from port 1 or port 4. All external
realizable low leakage performance, dual hydraulic pilot parts are zinc plated and chromited (CrVI-free) and are thus
operated check valve, for use as a blocking or load holding suitable for use in the harshest operating environments. If
device at high pressure applications.This valve allows free you intend to manufacture your own cavities or are desi
flow from port 2 to port 1 and from port 3 to port 4 and it gning a line-mounting installation, please refer to the sec
blocks flow from port 1 to port 2 and from port 4 to port 3. tion “Related data sheets”.
Flow is allowed from port 1 to port 2 when pilot pressure is
2 Symbol
1 4
2 3
3 Technical data
Reference: 520-P-011510-EN-00
Issue: 11.2015 1/4
Hydraulic characteristics Description, value, unit
Maximum operating pressure 3600 psi (250bar)
Maximum flow rate 5 gpm (19l/min)
Pilot Ratio 3.0 to 1
Leakage flow rate 5 drops/min @ 3500 psi (5 drops/min @ 240 bar)
Flow direction see symbol
Hydraulic fluid HL and HLP mineral oil to DIN 51 524;
for other fluids, please contact BUCHER
Hydraulic fluid temperature range -40°F…+250°F (-40°C…+120°C)
Viscosity range 15…380mm2/s (cSt), recommended 20...130mm2/s (cSt)
Minimum fluid cleanliness class 18/16/13
Cleanliness class to ISO 4406:1999
4 Performance graphs
measured with oil viscosity 33mm2/s (cSt)
p = f (Q) Pressure drop - Flow rate characteristic p = f (Q) Pressure drop - Flow rate characteristic
“free flow 2 1“ “free flow 3 4“
p [psi (bar)] p [psi (bar)]
EL_P0022.ai EL_P0023.ai
250 (17.2) 250 (17.2)
50 (3.5) 50 (3.5)
0 (0) 0 (0)
0 1 2 3 4 5 0 1 2 3 4 5
(0) (3.8) (7.8) (11.4) (15) (19) (0) (3.8) (7.8) (11.4) (15) (19)
Q [gpm (l/min)] Q [gpm (l/min)]
Attention:
When flow passes through the check valve and
there is a large pressure difference, the poppet in
the main stage can be damaged.
Q = f (p; I) Flow rate adjustment characteristic Q = f (I; p) Flow rate adjustment characteristic
“pilot 3 flow 1 2“ “pilot 2 flow 4 3“
p [psi (bar)] p [psi (bar)]
EL_P0024.ai EL_P0025.ai
250 (17.2) 250 (17.2)
50 (3.5) 50 (3.5)
0 (0) 0 (0)
0 1 2 3 4 5 0 1 2 3 4 5
(0) (3.8) (7.8) (11.4) (15) (19) (0) (3.8) (7.8) (11.4) (15) (19)
Q [gpm (l/min)] Q [gpm (l/min)]
2/4 520-P-011510-EN-00/11.2015
Series PDCV-08…
5 Dimensions & sectional view
Dimensions in inches (millimeters)
1.00 HEX
[25.4]
Tightening torque MA 2) ±10%
MA= 2)
.85
4
3/4−16 UNF
4
[76.2]
3.00
2
6
[54.6]
2.15
3 2
1
5
2 1
3
7
3
1
6 Installation information
Important: ATTENTION!
When fitting the cartridges, use the specified Only qualified personnel with mechanical skills
tightening torque. No adjustments are necessary, may carry out any maintenance work. Generally,
since the cartriges are set in the factory. the only work that should ever be undertaken is to
check, and possibly replace, the seals. When
changing seals, oil or grease the new seals tho
roughly before fitting them.
520-P-011510-EN-00/11.2015 3/4
Series PDCV-08…
7 Ordering code
PDCV - 08 - N - C - O
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
E 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense. The
information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to continual
improvement, we reserve the right to amend the product specifications contained in this catalogue.
Classification: 430.315.345.305.305
4/4 520-P-011510-EN-00/11.2015
Series PDCV-08…
POCD-10
1 4 1 4
PILOT OPERATED DUAL CHECK VALVE
WITH OPTIONAL THERMAL RELIEF 2 3 2 3
TORQUE:
Steel = 55/60 Ft-Lb. [74/81 Nm]
Aluminum = 35/40 Ft-Lb. [47/54 Nm]
1.06"
[27,0]
HEX
1.00
[25,4]
3.50"
[88,9]
2.49"
[63,2] 3
2
2.50"
[63,5]
1
POCD-10-X-X-X
L/M (28,5 cSt)
0 7,6 15,1 22,7 30,3 37,9
PORTS 200 13,8
BASIC 0 = CARTRIDGE ONLY
02BX = G 1/4" BSPP 175 D
SIZE
03BX = G 3/8" BSPP TE
150 LO 10,3
PRESSURE PSI
Reference: 520-P-011320-EN-00/09.2015
POCD-10
PILOT OPERATED DUAL CHECK VALVE
WITH OPTIONAL THERMAL RELIEF
DESCRIPTION
This unit is a SCREW IN, cartridge type, guided poppet,
hydraulic pilot operated dual check valve, for use as a blocking
or load holding device for high pressure applications.
Thermal relief option available in one direction.
OPERATIONS
This check valve allows free flow from port 2 to port 1 and
from port 3 to port 4. It blocks flow from port 1 to port 2
and from port 4 to port 3 or holds a load. Flow will be allowed
from port 1 to port 2 when pilot pressure is applied to port 3
that is higher than one-third of the load pressure at port 1.
Flow will be allowed from port 4 to port 3 when pilot pressure
is applied to port 2 that is higher than one-third of the load
pressure at port 4.
This pilot operated check valve has a 3 to 1 pilot ratio.
Port 4 can be equipped with a thermal relief. The relief is set to
open when the pressure in port 4 exceeds the relief setting.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 10.0 GPM [37.9 l/m] nominal. See performance chart.
PILOT RATIO: 3 TO 1
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1042 Buna "N"
SKV-1042 Viton
WEIGHT: .40 lb. [.19 kg] cartridge only.
VALVE CAVITY: #C1040, See Page 0-042.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-011320-EN-00/09.2015
DPOC-08
C1 C2
DUAL PILOT OPERATED CHECK VALVE POPPET
TYPE, PILOT TO OPEN, 3 TO 1 PILOT RATIO. V1 V2
"F" FIXED
0.85
[21,6]
V2
Elgin, Illinois
MODEL NUMBER
DPOC-08-X-F-X-XX
2.50
1.12 V1 V2 [63,5]
[28,5]
C1 C2
1.37 0.60
[34,8] [15,2]
3.37 1.20
[85,6] [30,5]
3.75
[95,3]
SIZE
08 = 3/4"-16 UNF CRACK PRESSURE
010 = 10 PSI 60
PRESSURE DROP (
150 10,5
030 = 30 PSI
SEALS
060 = 60 PSI
N = BUNA "N"
V = VITON 30
100 7,0
ADJUSTMENT
F = FIXED PORTS
10
03BX = G 3/8" BSPP 3,5
50
04BX = G 1/2" BSPP
08TX = SAE - #8
Reference: 520-P-011410-EN-00/09.2015
DPOC-08
DUAL PILOT OPERATED CHECK VALVE
POPPET TYPE, PILOT TO OPEN, 3 TO 1 PILOT RATIO.
DESCRIPTION
This unit is a cartridge type, guided poppet, with cross line
pilot, dual hydraulic pilot operated check valve, for use as a blocking
or load holding device for high pressure applications.
OPERATIONS
This valve allows free flow from port V1 to port C1 and V2 to C2
then blocks reverse flow until a pilot pressure is sensed at pilot
ports which are connected to ports V1 and V2 therefore opening flow
from port C1 or port C2.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 10.0 GPM [38 l/m] nominal. See performance chart.
PILOT RATIO: 3 TO 1
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-0828 Buna "N"
SKV-0828 Viton
WEIGHT: 1.70 lb [.77 kg].
VALVE CAVITIES: #C0825, See Page 0-021.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-011410-EN-00/09.2015
DPOC-10
C1 C2
DUAL PILOT OPERATED CHECK VALVE POPPET
TYPE, PILOT TO OPEN, 3 TO 1 PILOT RATIO. V1 V2
1.63"
[42,3]
.795"
[20,1]
V2
1.30"
[33,0]
V2
V1
3.00"
[76,2]
C1 C2
1.50"
[38,1]
3.63" .63"
[15,9]
[92,1]
1.25"
4.00"
[31,8]
[101,6]
BASIC
200 13,6
P)
SIZE
10 = 7/8"-14 UNF CRACK PRESSURE
010 = 10 PSI 60
PRESSURE DROP (
Reference: 520-P-011420-EN-00/09.2015
DPOC-10
DUAL PILOT OPERATED CHECK VALVE
POPPET TYPE, PILOT TO OPEN, 3 TO 1 PILOT RATIO.
DESCRIPTION
This unit is a cartridge type, guided poppet, with cross line
pilot, dual hydraulic pilot operated check valve, for use as a blocking
or load holding device for high pressure applications.
OPERATIONS
This valve allows free flow from port V1 to port C1 and V2 to C2
then blocks reverse flow until a pilot pressure is sensed at pilot
ports which are connected to ports V1 and V2 therefore opening flow
from port C1 or port C2.
This pilot operated check valve has a 3 to 1 pilot ratio, meaning
that it takes at least one-third of the load pressure held at port 1
that is required at port 3 to open the valve.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 18.0 GPM [70 l/m] nominal. See performance chart.
PILOT RATIO: 3 TO 1
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
SEAL KIT: SKN-1028 Buna "N"
SKV-1028 Viton
WEIGHT: 1.85 lb [.92 kg].
VALVE CAVITIES: #C1025, See Page 0-022.0.
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-011420-EN-00/09.2015
DPOC-12
C1 C2
DUAL PILOT OPERATED CHECK VALVE POPPET
TYPE, PILOT TO OPEN, 3 TO 1 PILOT RATIO. V1 V2
1.99"
[50,5]
1.13"
[28,6]
1.67" V2
[42,4]
V1
V2
3.50"
[88,9]
C1 C2
1.90" .81"
[48,3] [20,7]
4.50"
[114,3] 1.63"
[41,3]
5.00"
[127]
BASIC
200 13,6
P)
SIZE
12 = 1.062"-12 UNF CRACK PRESSURE
010 = 10 PSI 60
PRESSURE DROP (
Reference: 520-P-011430-EN-00/09.2015
DPOC-12
DUAL PILOT OPERATED CHECK VALVE
POPPET TYPE, PILOT TO OPEN, 3 TO 1 PILOT RATIO.
DESCRIPTION
This unit is a cartridge type, guided poppet, with cross line
pilot, dual hydraulic pilot operated check valve, for use as a blocking
or load holding device for high pressure applications.
OPERATIONS
This valve allows free flow from port V1 to port C1 and V2 to C2
then blocks reverse flow until a pilot pressure is sensed at pilot
ports which are connected to ports V1 and V2 therefore opening flow
from port C1 or port C2.
This pilot operated check valve has a 3 to 1 pilot ratio, meaning
that it takes at least one-third of the load pressure held at port 1
that is required at port 3 to open the valve.
SPECIFICATIONS
OPERATING PRESSURE: 5,000 PSI [350 Bar]
PROOF PRESSURE: 10,000 PSI [700 Bar]
FLOW: 36.0 GPM [136.3 l/m] nominal. See performance chart.
PILOT RATIO: 3 TO 1
INTERNAL LEAKAGE: 5 drops per minute maximum @ 5,000 PSI [350 Bar]
VALVE HOUSINGS: 2500 PSI [175 Bar] = Aluminum - Anodized.
5000 PSI [350 Bar] = Steel - Unplated.
OPERATING TEMPERATURE: -40° to +250° F. [-40° to +120° C.]
OPERATING MEDIA: All general purpose hydraulic fluids such as
MIL-H-5606, SAE-#10, SAE-#20, etc.
INSTALLATION: No restrictions.
FILTRATION: 25 microns or better.
SEAL KIT: SKN-1228 Buna "N"
SKV-1228 Viton
WEIGHT: 2.65 lb [1.21 kg] Aluminium. 5.25 lbs [2.38] Steel.
VALVE CAVITIES: #C1225
info.el@bucherhydraulics.com www.bucherhydraulics.com/commoncavity
© 2015 by Bucher Hydraulics, Inc., 2545 Northwest Parkway, Elgin, Illinois 60124, USA
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
Reference: 520-P-011430-EN-00/09.2015
PTCC-10
PILOT OPERATED CHECK VALVE POPPET TYPE, 1 2
PILOT TO CLOSE, PILOT RATIO. 3
TORQUE:
Steel = 55/60 Ft-Lb. [74/81 Nm]
Aluminum = 35/40 Ft-Lb. [47/54 Nm]
1.06"
[27,0]
HEX
"F" FIXED
1.63"
[42,3]
.847"
[21,5]
2.75"
[69,8]
3
1.85"
[46,9]
2
2.50" 1
[63,5]
NOTE: FOR ALUMINUM OR STEEL VALVE HOUSING CONFIGURATIONS SEE PAGE 0-022.1.
100 6,8
P)
SIZE
10 = 7/8"-14 UNF PILOT RATIO
2 = 2 TO 1
PRESSURE DROP (
3 = 3 TO 1
SEALS 75 5,2
N = BUNA "N" 3 TO 1 RATIO
V = VITON 2 TO 1 RATIO
PORTS
ADJUSTMENT 0 = CARTRIDGE ONLY 50 3,4
F = FIXED 06TX = SAE - #6
M = MANUAL RELEASE 08TX = SAE - #8
02BX = 1/4" BSPP
25 1,7
03BX = 3/8" BSPP
Reference: 520-P-012020-EN-00/09.2015
PTCC-10
PILOT OPERATED CHECK VALVE
POPPET TYPE, PILOT TO CLOSE, PILOT RATIO.
DESCRIPTION
This unit is a SCREW-IN cartridge type, guided poppet,
hydraulic pilot operated check valve, for use as a blocking
or load holding device for high pressure applications.
OPERATIONS
This valve allows free flow from port 1 to port 2 and blocks
flow from port 2 to port 1 for holding a load. Flow will not be
allowed from port 2 to port 1 when pressure is applied to port 3.
This pilot operated check valve has a 3 to 1 or 2 to 1 pilot ratio,
meaning that port 3 requires at least one-third or half of the load
pressure held at port 2 to close the valve.
Reference: 520-P-012020-EN-00/09.2015