Escolar Documentos
Profissional Documentos
Cultura Documentos
TITLE:
A/C Reg.:
32-41-12-400-001-A - Installation of the NLG Wheel
** ON A/C 163-163, 170-170
RP-C3272
CARD: ZONE: 711 INTERVAL:
SKILL: ACCESS:
MECH. INSP.
** ON A/C ALL
TASK 32-41-12-400-001-A
Installation of the NLG Wheel
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE
LANDING GEAR. MOVEMENT OF THE LANDING GEAR CAN CAUSE INJURY
TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
REFERENCE QTYDESIGNATION
No specific 1 AIR SOURCE FILTERED, DRY
No specific AR WARNING NOTICE(S)
No specific Torque wrench: range
to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in)
No specific Torque wrench: range
to between 0.4 and 0.51 m.daN (35.40 and 45.13 lbf.in)
No specific Torque wrench: range to 10.8 m.daN (79.65 lbf.ft)
No specific Torque wrench: range to 21.80 m.daN (160.77 lbf.ft)
(1324A) 1 HANDLING TOOL
(J47549) 1 ADAPTOR NLG
B. Consumable Materials
REFERENCE DESIGNATION
(Material No. 03GBB1) Synthetic Oil base Grease-General Purpose Clay
Thickened -
(Material No. 03GCB1) Synthetic Oil base Grease-Landing Gear Wheel Bearing
Lithium Thickened -
(Material No. 06LCG9) Non Hardening Jointing Putty-Medium Temp. Area - -
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 7
JCP Ref: reference DATABASE REV DATE: Aug 01/2017
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Aug 24/2017 18:50
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-12-400-001-A
32-41-12 PB 401
TITLE:
A/C Reg.:
32-41-12-400-001-A - Installation of the NLG Wheel
** ON A/C 163-163, 170-170
RP-C3272
MECH. INSP.
REFERENCE DESIGNATION
(Material No. 08BBB1) Non Aqueous Cleaner-- Petroleum Based -
D. Expendable Parts
E. Referenced Information
REFERENCE DESIGNATION
(Ref. 07-12-00-582-001-A). Jacking of the Nose Landing Gear
(Ref. 12-14-32-614-001-A). Nitrogen Filling of the Tires
(Ref. 32-00-00-081-001-A). Removal of the Safety Devices from the Landing Gears
(Ref. 32-00-00-481-001-A). Installation of the Safety Devices on the Landing Gears
(Ref. 32-41-00-210-003-A). Inspection/Check of the Tire Pressure
(Ref. 32-41-00-910-001-A). Tire Mixability Precautions
(Ref. 12-22-00-00). LUBRICATION - DESCRIPTION AND OPERATION
Nose Gear Wheel SHEET 1
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 7
JCP Ref: reference DATABASE REV DATE: Aug 01/2017
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Aug 24/2017 18:50
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-12-400-001-A
32-41-12 PB 401
TITLE:
A/C Reg.:
32-41-12-400-001-A - Installation of the NLG Wheel
** ON A/C 163-163, 170-170
RP-C3272
MECH. INSP.
A
1
2
3
4 A
2660GM
5 2659GM
A
6
11
10
5
4
3
2
9
8
7
N_MM_324112_4_AAM0_01_00
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 7
JCP Ref: reference DATABASE REV DATE: Aug 01/2017
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Aug 24/2017 18:50
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-12-400-001-A
32-41-12 PB 401
TITLE:
A/C Reg.:
32-41-12-400-001-A - Installation of the NLG Wheel
** ON A/C 163-163, 170-170
RP-C3272
MECH. INSP.
3. Job Set-up
Subtask 32-41-12-865-051-A
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
NOTE: If the wheel has a pressure-sensor seal cap, make sure that the seal cap is
correctly installed and safetied with a nut and a cotter pin.
NOTE: If the wheel has a Tire Pressure Indicating System (TPIS), the tie-bolt balance
weight must be installed 180 degrees from the TPIS sensor holder.
Subtask 32-41-12-210-054-A
A. Tires of different type
(1) Obey the tire mixability precautions (Ref. AMM TASK 32-41-00-910-001) .
Subtask 32-41-12-420-053-A
B. Installation of the NLG Wheel
CAUTION: MAKE SURE THAT THE GREASE USED FOR THE AXLE SLEEVE
IS THE SAME AS THE GREASE USED FOR THE BEARINGS (CONE
AND CAGE). IF YOU USE A DIFFERENT GREASE, YOU CAN CAUSE
DAMAGE TO THE BEARINGS.
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 7
JCP Ref: reference DATABASE REV DATE: Aug 01/2017
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Aug 24/2017 18:50
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-12-400-001-A
32-41-12 PB 401
TITLE:
A/C Reg.:
32-41-12-400-001-A - Installation of the NLG Wheel
** ON A/C 163-163, 170-170
RP-C3272
MECH. INSP.
NOTE: You must make sure that the wheel does not turn when you loosen
the axle nut.
(g) TORQUE the axle nut (10) to 10.8 m.daN (79.65 lbf.ft) with the ADAPTOR
NLG (J47549) and, at the same time, turn the wheel in the same direction.
(h) Tighten the axle nut (10).
1 Tighten the axle nut (10) until one hole is aligned with the first
subsequent hole in the axle.
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 5 of 7
JCP Ref: reference DATABASE REV DATE: Aug 01/2017
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Aug 24/2017 18:50
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-12-400-001-A
32-41-12 PB 401
TITLE:
A/C Reg.:
32-41-12-400-001-A - Installation of the NLG Wheel
** ON A/C 163-163, 170-170
RP-C3272
MECH. INSP.
(i) Turn the wheel and make sure that the wheel is installed correctly.
(j) Install the casing (9).
(k) Installation of the bolts
1 Install the bolts (5), the washers (2) and the new IPC -CSN (32-21-13-
12-070) nuts (3) or IPC -CSN (32-21-13-22-070) nuts (3).
(l) TORQUE the nuts (3)
to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in).
(m) Safety the nuts (3) with the new IPC -CSN (32-21-13-12-060) cotter pins (4)
or IPC -CSN (32-21-13-22-060) cotter pins (4).
Subtask 32-41-12-410-051-A
C. Close access
(1) Put the hubcap (6) in position.
(2) Apply a thin layer of Non Hardening Jointing Putty-Medium Temp. Area -
- (Material No. 06LCG9) to the screws (7).
(3) Install the screws (7) and the washers (8).
(4) TORQUE the screws (7)
to between 0.4 and 0.51 m.daN (35.40 and 45.13 lbf.in).
NOTE: The hubcap attachment holes have screw-lock inserts. It is not necessary
to install lockwire on the screws (7).
Subtask 32-41-12-420-053-B
DELETED
Subtask 32-41-12-410-051-B
DELETED
Subtask 32-41-12-860-051-A
D. Aircraft Maintenance Configuration
(1) Inflate the tire to the unloaded pressure (Ref. AMM TASK 12-14-32-614-001) .
(2) Lower the aircraft on its wheels (Ref. AMM TASK 07-12-00-582-001) .
(3) Make sure that the pressure of the tire is correct (Ref. AMM TASK 32-41-00-210-
003) .
Subtask 32-41-12-865-052-A
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 6 of 7
JCP Ref: reference DATABASE REV DATE: Aug 01/2017
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Aug 24/2017 18:50
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-12-400-001-A
32-41-12 PB 401
TITLE:
A/C Reg.:
32-41-12-400-001-A - Installation of the NLG Wheel
** ON A/C 163-163, 170-170
RP-C3272
MECH. INSP.
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 7 of 7
JCP Ref: reference DATABASE REV DATE: Aug 01/2017
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Aug 24/2017 18:50
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE