Escolar Documentos
Profissional Documentos
Cultura Documentos
AVSpare
Usage:
REBAJAS 2019
3054 CHN 3056 SNX 3054 TCN
ENVÍO GRATIS
Engine:
3054 (S/N: CHN1-UP; TCN1-UP)
Introduction
Note: Within this instruction, the term PC refers to the device on which the utility software is loaded. The term, PC, can be
either a desktop personal computer or else a laptop computer.
This instruction assists in programming the multiline-2 controller, part number 238-4635 using the Cat version NEXG-5078 of
the utility software.
Configuration file changes supplied by the manufacturer cause programming issues. A controller that uses new Cat version
configuration files cannot be programmed using a PC that is loaded with the old (DEIF) utility software.
Set Repostería 34 Piezas Azul
When the incorrect utility software is used in order to program the controller, the controller may not operate correctly. For Bakers Dreams & Beginers.
example, the starter relay may not operate if incompatible software is used. If the Cat version configuration file is downloaded $1.099
to the controller using the latest Cat version NEXG-5078 utility software, then the controller should operate correctly.
$599
This special instruction provides information of how to determine the compatibility of software versions that are loaded in both 45%OFF
the controller and the PC. This special instruction provides information of how to determine if the versions are incompatible
Comprar ahora
and the method for updating the software.
For controllers that are in service and operating correctly, no action is needed. This instruction only applies when
programming or reprogramming is required when connected to a PC.
ReferenceREHS2226 Special Instruction, "Operating controls for the Multiline-2 Controllers" Recent
Optional Tools
This Special Instruction contains references to the optional tools listed in Table 1. 5H0779 Caterpillar
CATERPILLAR GASKET
Optional Tools 5H0779 NEW
2S7472 Caterpillar
Table 1
CATERPILLAR GASKET
(1)
Contains the three items listed below 2S7472 NEW
https://avspare.com/catalog/cat/content/i02437588/ 1/11
28/1/2019 Programming Instructions for the Multiline-2 Controller{7451, 7620} #i02437588 Caterpillar
Each step within the process flow is described in detail in later sections of this Special Instruction. Illustration 17 provides a
single page reference flow chart of the complete process.
3. Referring to Table 2, determine whether an upgrade to either the PC or to the controller is needed in order to ensure
compatibility.
Table 2
(1)
Although there is compatibility between the two devices, an upgrade to both the controller and the PC using the latest
versions of Catsoftware is recommended.
4. If CAT software is installed in both the PC and in the controller, then no further action is required.
5. If DEIF software is installed in both the PC and in the controller, then no further action is required. Although not
required, Caterpillar highly recommends installation of CAT version software in both the PC and in the controller.
Reference""Installing the CAT Utility Software" " and ""Installing the CAT Controller Software" "
6. If CAT software is installed on the controller but not on the PC, then install the CAT utility software on the PC.
Reference""Installing the CAT Utility Software" "
7. If CAT software is installed on the PC but not on the controller, then install CAT software on the controller using the
following procedure.
Reference""Installing the CAT Controller Software" "
a. Create a parameter configuration file by uploading the existing parameters from the controller to the PC.
(optional)
d. If needed, manually set the controller parameters using either the front panel of the controller or else by using
the CAT utility software.(optional)
https://avspare.com/catalog/cat/content/i02437588/ 2/11
28/1/2019 Programming Instructions for the Multiline-2 Controller{7451, 7620} #i02437588 Caterpillar
Illustration 1 g01218667
Logo indicates that CAT software is loaded in the PC
2. Determine which logo is displayed in the top left corner of the window.
If the CAT logo is displayed, then the CAT utility software is installed
If the DEIF logo is displayed, then the DEIF utility software is installed
Illustration 2 g01218669
2. On the controller, press the Left Arrow button (1) three times.
If CAT VER.X.X.X is displayed, then the controller is loaded with CAT software.
If ML2-STD VER.X.X.XX.X is displayed, then the controller is loaded with DEIF software.
1. Obtain the CAT utility software using one of the following methods.
Method 1 Order NEXG-5078 CD ROM (part of 243-3142 Control Module Service GP )
Method 2 Download the zip file from the https://dealer.cat.com website as follows:
b. On right side of screen under "Technical Information", select "Marine Diagnostic Service Software Tool". A new
window will open with the available MCS control panel files.
c. Select MCS0.
https://avspare.com/catalog/cat/content/i02437588/ 3/11
28/1/2019 Programming Instructions for the Multiline-2 Controller{7451, 7620} #i02437588 Caterpillar
a. Using a mouse or touch pad, right-click on My Computer, and then select Properties from the menu. The
"System Properties" window opens.
b. Select the Hardware tab in the "System Properties" window, and then select Device Manager. The "Device
Manager" window opens.
c. Expand the Ports section in the "Device Manager" window by selecting the "+" sign that is to the left of the ports
section. The window expands with ports that are available for configuration.
Illustration 3 g01218653
Device Manager window with available ports expanded
d. Determine to which port the serial communications cable is connected between the PC and the controller.
Double-click this port. A "Communications Port Properties" window opens for the selected port.
Illustration 4 g01219792
f. If the values in the window are the same as the values in Table 3, then select Cancel. If the values are not
correct, then modify the incorrect values. After all modifications are complete, select OK.
Data bits 8
Parity None
Stop bits 1
https://avspare.com/catalog/cat/content/i02437588/ 4/11
28/1/2019 Programming Instructions for the Multiline-2 Controller{7451, 7620} #i02437588 Caterpillar
Table 3
g. Close the Device Manager window and close the System Properties window.
a. Open the CAT utility software. The setup Welcome screen appears
After the Setup program ends, the CAT utility software opens and displays the CAT logo shown in Illustration 5.
Illustration 5 g01218667
Illustration 6 g01218717
c. Select the Application Settings icon (3) that is located in the tool bar at the top of the window. The "Settings"
window for the application opens.
Illustration 7 g01219461
d. Select the Communication setting. The "Communcation-related settings (modbus and port)" window opens.
e. Modify any values in the window that are not the same as the values specified in Table 4.
Communication Port 1
https://avspare.com/catalog/cat/content/i02437588/ 5/11
28/1/2019 Programming Instructions for the Multiline-2 Controller{7451, 7620} #i02437588 Caterpillar
Device modbus ID 2
Max attempts 3
Deselected
Use modbus ASCII (default is modbus RTU)
(Checkbox empty)
Table 4
Uploading the parameters from the controller in order to create a parameter file [OPTIONAL]
Adjusting the parameters that were optionally downloaded to the controller as required [OPTIONAL]
1. On the toolbar at the left of the window, select Parameters. The device icon toolbar opens.
Illustration 8 g01218713
2. On the device icon toolbar, select the Upload parameters icon (4). The system begins transferring file data from the
controller.
3. After the data transfer is complete, select File and then select Save.
5. Select Save in order to save the new parameters to the designated file.
Connect to the controller and then download the CAT configuration file from the PC to the controller. The following sections
discuss this process.
2. Perform the following in order to upload the information from the controller. Connect a null modem cable from the
communication port in the PC to the service port on the controller.
Note: A null modem cable can be ordered. Use part number 243-3143 (part of 243-3142 Controller Service GP ).
Note: If a cable is not available, a cable can be built according to the wiring diagram in Illustration 9.
https://avspare.com/catalog/cat/content/i02437588/ 6/11
28/1/2019 Programming Instructions for the Multiline-2 Controller{7451, 7620} #i02437588 Caterpillar
Illustration 9 g01218992
Attach the shield (5) of the null modem cable to the metallic casing of the plugs. If the plugs have non-metallic casings, then
leave the shield unconnected.
Note: There is no need to connect the front cover in order to communicate with the PC. However, the front cover must
be connected in order to operate the controller. Operation of the controller is accomplished while connected to the PC.
Connection to the PC requires a 1U-9484 Cable Harness from the controller to the front cover. The 1U-9484 Cable
Harness is part of the 243-3142 Controller Service GP .
Illustration 10 g01219478
3. Press the Connect icon (6) in the tool bar at the top of the window. The information uploads from the controller and a
screen similar to the one shown in Illustration 11 appears.
Illustration 11 g01219479
Illustration 12 g01219481
1. Press the Flash icon (7) on the tool bar at the top of the window in order to download the configuration file to the
device. Click OK.
2. If prompted for a password, enter the value 2000 and then select OK.
4. When prompted, click Yes in order to erase the existing program and download (flash) the selected program.
5. After the selected program has been successfully flashed, then select OK in order to reboot the controller.
After the CAT configuration file has been loaded into the controller, then the optionally created parameter file may be
downloaded to the controller.
Note: Prior to completing the following procedure, ensure that the CAT utility software has been installed.
1. Select Parameters in the tool bar that is located to the left of the main window. The "Parameters" window opens.
Illustration 13 g01218781
3. Select the required Parameter file and then select Open. A screen similar to the one shown in Illustration 13 appears.
This screen lists parameter information such as the category, the channel, a textual description, and other values
associated with the parameter.
Illustration 14 g01218782
4. Select the Start communication (8) icon in the tool bar that is located at the top of the main window.
5. If prompted for a password, enter a value of 2000 and then select OK.
https://avspare.com/catalog/cat/content/i02437588/ 8/11
28/1/2019 Programming Instructions for the Multiline-2 Controller{7451, 7620} #i02437588 Caterpillar
If needed, the parameters can be adjusted by using either the front panel of the controller, or else by using the Utility
software.
3. Select the required Parameter file and then select Open. A screen appears listing parameter information such as the
category, the channel, a textual description, and other values associated with the parameter.
Note: When adjusting a parameter, be aware that related parameters may also need to be adjusted, for example,
Nominal Voltage and Power Output.Max.
5. Modify the values of the parameter as required by selecting the value and entering the new setting in the field.
Illustration 15 g01219809
6. Select or deselect the check box fields in order to enable or disable the function. A function that is enabled will display
a check mark (9) in the check box.
7. After all changes are complete, select Write and then select OK.
https://avspare.com/catalog/cat/content/i02437588/ 9/11
28/1/2019 Programming Instructions for the Multiline-2 Controller{7451, 7620} #i02437588 Caterpillar
Illustration 16 g01219637
The flow chart in Illustration 16 shows the steps for adjusting the parameters using the front control panel.
Note: If prompted for a password during this procedure, then enter a value of 2000.
Illustration 17 g01219648
Note: Dotted boxes contain optional steps.
https://avspare.com/catalog/cat/content/i02437588/ 10/11
28/1/2019 Programming Instructions for the Multiline-2 Controller{7451, 7620} #i02437588 Caterpillar
Use the process flow chart in Illustration 17 as a reference. The process needs to be used in order to ensure that both the PC
utility software and the controller software are compatible with each other.
$52.15
29-01-2019
5I7579
$52.15
29-01-2019
5I7579
$52.15
29-01-2019
5I7579
Contacts The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment
Request list manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions,
numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and
descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.
https://avspare.com/catalog/cat/content/i02437588/ 11/11