Escolar Documentos
Profissional Documentos
Cultura Documentos
I. PILING ....................................................................................................... 14
II. EXCAVATION............................................................................................ 16
V. ROOFING .................................................................................................. 24
I. PILING
A. TIMBER PILES
1. Bakau Piles
Supply and drive bakau pile
a) 75mm diameter ne 5.00m long No 15.00
b) 75mm diameter 5.00 - 10.00m long, including mild steel
pipe sleeves No 26.15
2. Mattress Piles
Supply and lay bakau roller
a) 75mm diameter m 4.05
B. CONCRETE PILES
C. STEEL PILES
1. Isolated Piles
Supply and drive steel 'H' piles complying with BS EN 10029, with corrosion
protection including extension by weld jointing
a) size 203 x 203mm x 53.57 kg/m m 143.65
b) size 254 x 254mm x 62.50 kg/m m 167.35
c) size 305 x 305mm x 78.87 kg/m m 204.00
d) size 330 x 330mm x 108.63 kg/m m 275.95
e) size 356 x 356mm x 132.44 kg/m m 326.40
D. BORED PILES
3. Steel Casing
a) Supply and drive steel casing to be left in for bored piles kg 2.60
E. MICROPILES
1. Bored Micropiles
Supply and install micropiles
a) 150mm diameter m 226.90
b) 200mm diameter m 257.65
c) 250mm diameter m 280.95
Cutting of pile to the required level including welding of the bearing plate
d) generally No 243.40
2. Driven Micropiles
Supply and drive steel micropiles complete with cement grouting to centre void
a) 114mm diameter (with working capacity of 20 ton each) m 96.45
Cutting of pile to the required level including welding of the bearing plate
b) Generally No 106.80
F. SUNDRIES
1. Pile Tests
Test loading of piles with the Kentledge reaction system including casting and
subsequent removal of temporary pile cap
a) generally t 69.45
II. EXCAVATION
A. SITE CLEARANCE
2. Remove Trees
Cut tree including grubbing up roots, filling voids and disposal of materials off site
a) 600 - 1000mm girth No 347.70
b) 1000 - 1500mm girth No 585.30
c) 1500 - 2000mm girth No 911.65
d) 2000 - 2500mm girth No 1,136.95
3. Oversite Excavation
Excavate over site, commencing from ground level, to reduce level
a) average 100mm deep m2 2.90
b) average 200mm deep m2 3.50
c) average 300mm deep m2 4.05
d) 300 - 1000mm deep m3 10.85
B. GENERAL EXCAVATION
1. Pit/Trench Excavation
Excavate to form trench, commencing from reduced level
a) ne 1.00m deep and cross sectional area ne 0.50m2 m 10.30
Excavate to form pit or trench, commencing from reduced level
b) ne 2.00m deep m3 19.35
c) 2.00 - 4.00m deep m3 28.65
d) 4.00 - 5.00m deep m3 40.95
2. Basement Excavation
Excavate to form basement, commencing from reduced level
a) ne 2.00m deep m3 18.05
b) 2.00 - 4.00m deep m3 25.15
3. Cutting
Excavate to form embankment, commencing from reduced level
a) generally m3 17.60
4. Break Up Obstructions
Extra over excavation for breaking up obstruction using mechanical means
a) brickwork and blockwork m3 30.15
b) mass concrete m3 47.05
c) reinforced concrete m3 96.10
d) rock m3 140.20
Cut surface pavement using pavement diamond cutter to achieve a straight edge
e) ne 150mm deep m 18.75
C. FILLING
1. Backfilling
Backfilling around trench, column base, pile cap, foundation beam and pier hole
a) excavated material obtained within the site m3 6.20
b) earthfilling obtained from contractor's own source m3 18.80
D. DISPOSAL
1. Excavated Material
Remove excavated material off site
a) for suitable excavated material m3 14.60
b) for unsuitable excavated material m3 32.10
1. Lean/Mass Concrete
Lean or Mass concrete complying with BS EN 1992-1-1
a) grade 10 m3 142.65
b) grade 15 m3 144.80
c) grade 20 m3 150.00
2. Reinforced Concrete
Reinforced concrete complying with BSEN 1992-1-1
a) grade 20 m3 151.35
b) grade 25 m3 154.15
c) grade 30 m3 156.85
d) grade 35 m3 159.00
e) grade 40 m3 162.80
f) grade 45 m3 166.65
g) grade 50 m3 171.35
h) grade 55 m3 178.40
3. Waterproofed Concrete
Waterproofed concrete complying with BSEN 1992-1-1 with approved waterproofing
compound
a) grade 30 m3 217.95
b) grade 35 m3 227.50
B. REINFORCEMENT
1. Bar Reinforcement
Mild steel bar reinforcement complying with SS 560
a) 6mm diameter kg 1.80
b) 10mm diameter kg 1.70
c) 13mm diameter kg 1.70
d) 16mm diameter kg 1.65
e) 20mm diameter kg 1.65
f) 22mm diameter kg 1.65
g) 25mm diameter kg 1.65
h) 28mm diameter kg 1.65
i) 32mm diameter kg 1.65
High tensile steel bar reinforcement complying with SS 560
j) 10mm diameter kg 1.60
k) 13mm diameter kg 1.55
l) 16mm diameter kg 1.55
m) 20mm diameter kg 1.55
n) 22mm diameter kg 1.55
2. Fabric Reinforcement
Welded steel fabric reinforcement complying with SS 561 and well lapped
(measured nett)
a) Reference No A5 m2 5.05
b) Reference No A6 m2 6.15
c) Reference No A7 m2 7.35
d) Reference No A8 m2 9.05
e) Reference No A9 m2 10.90
f) Reference No A10 m2 12.40
g) Reference No B5 m2 7.75
h) Reference No B6 m2 8.60
i) Reference No B7 m2 9.60
j) Reference No B8 m2 12.00
k) Reference No B9 m2 13.80
l) Reference No B10 m2 15.80
m) Reference No B11 m2 18.05
n) Reference No B12 m2 20.60
o) Reference No B13 m2 20.95
p) Reference No D6 m2 9.85
q) Reference No D7 m2 12.20
r) Reference No D8 m2 15.40
s) Reference No D9 m2 18.95
t) Reference No D10 m2 23.05
u) Reference No D11 m2 27.50
v) Reference No D12 m2 32.40
C. PRECAST CONCRETE
1. Kerb or Divider
Precast concrete kerb or divider in Grade 25 concrete including laying in alignment
and finishing fair on all exposed surfaces
a) 125 x 250mm Type K2A Kerb m 17.00
b) 125 x 275mm Type K2B Kerb m 17.25
c) 150 x 300mm Type D1 Divider m 16.45
Extra over Type K2A/B Kerb with slot hole
d) generally No 4.30
2. Cover Slab
Precast concrete Grade 30 cover slab all as detailed in SDRE – Drains & Culverts
a) 640 x 270 x 75mm No 11.45
D. FORMWORK
1. Sawn Formwork
Sawn formwork to in-situ concrete including strutting not exceeding 3.5m high
a) curved surface m2 44.55
b) plain surface m2 38.50
2. Wrought Formwork
Wrought formwork to in-situ concrete including strutting not exceeding 3.5m high
a) curved surface m2 52.90
b) plain surface m2 48.20
3. Strutting
Extra over for strutting exceeding 3.50m high
a) Every 1.50m high m2 5.45
2. Water-stops
PVC water-stop embedded in concrete at interfaces of structural elements
a) 200mm wide m 26.65
b) 250mm wide m 36.85
3. Protection
Polystyrene board fixed to external surface of concrete
a) 25mm thick, 16 kg/m3 grade m2 10.50
F. SUNDRIES
1. Expansion Joints
75mm high bitumen impregnated fibreboard joint filler
a) 12mm thick m 3.15
b) 20mm thick m 3.70
c) 25mm thick m 4.45
Polyethylene bond breaking strip to joint
d) 10mm diameter m 3.05
e) 15mm diameter m 3.40
f) 25mm diameter m 3.75
25mm wide polysulphide sealer to joint
g) 15mm deep m 18.15
h) 25mm deep m 29.30
15mm wide x 50mm deep heavy duty approved sealant
i) generally m 16.50
15mm wide x 175mm deep impregnated flexcell board
j) generally m 12.00
2. Trowelling
Labour trowel top surface of concrete to a smooth finish including additional cement
a) generally m2 7.35
3. Cutting To Concrete
Labour in cutting reinforced concrete to form groove not exceeding 100mm wide
including rendering with cement mortar (1:3)
a) ne 50mm deep m 9.20
b) 50 - 100mm deep m 17.70
4. Demolition
Break up existing concrete structure including cutting and bending reinforcement
and removal of debris off site
a) opening ne 0.10 m3 No 66.55
b) opening 0.10 - 0.20m3 No 91.25
c) opening exceeding 0.20m3 m3 441.95
A. CLAY BRICKS
B. CONCRETE BLOCKS
1. Hollow Blockwork
Hollow concrete block complying with SS271 : 1983 in cement mortar (1:4) with
mortar plasticiser
a) 75mm thick wall m2 23.85
b) 100mm thick wall m2 25.95
c) 150mm thick wall m2 34.35
C. GLASS BLOCKS
1. Walls/Panels
Glass block in wall or panel in cement mortar (1:4) with mortar plasticiser
a) 150 x 150 x 100mm thick m2 403.75
b) 190 x 190 x 100mm thick m2 307.55
V. ROOFING
A. BUILT-UP ROOFING
1. Felt Roofs
Bituminous felt roofing on flat roof including sealing and bonding
a) 1-ply felt; 17.75 kg per 20m2 m2 30.75
b) 2-ply felt; 35.50 kg per 20m2 for each layer m2 55.85
c) 3-ply felt; first and second layers each weighing 27 kg
per 20m2 and third layer weighing 45 kg per 20m2 m2 73.65
1. Steel Deckings
High tensile profile patent Colorbond/colorcote with zincalume coating roof or wall
cladding fixed to steel or timber framing (measured separately) with fixing clips and
self-tapping screws
a) 0.47mm thick sheet m2 41.95
b) 0.53mm thick sheet m2 46.95
A. STRUCTURAL STEELWORK
B. METALWORK
Hot dip galvanised brace support (on one side) including post, spacer, brace with
mild steel plates welded, set in and including concrete foundation, all necessary
excavation, disposal of excavated material as per SDRE – Guardrails
c) 150 × 150 × 6mm SHS Set 453.40
3. End terminal
Design, supply and install end terminal complete with end terminal, post, support,
foundation, cable-anchor assembly, W-beam and all necessary fixings as per SDRE
– Guardrails
a) Type B - 10.1m long cable anchored terminal as per
SDRE – Guardrails Set 11,143.10
b) Thrie-Beam Transition consisting of thrie-beam
transition section, thrie-beam and end piece Set 6,611.10
Design, supply and install crash cushion in compliance with NCHRP 350 Test
complete with end terminal, post, support, foundation, W-beam and all necessary
fixings as per SDRE – Guardrails
b) Crash cushion Set 46,161.00
D. RAILING
E. GRATING
1. Pedestrian Grating
Mild steel grating in panels consisting of 80 x 38 x 4.6mm galvanised steel angle
frame, with 35 x 9mm galvanised mild steel flat all round, in filled with 25 x 5mm
galvanised mild steel flat, all joints and intersections whole welded, drilled and
including painting with one coat of inhibitive primer before delivery and built into
concrete surround including 3mm thick mild steel plate ≤ 3mm thick anti-slip coating,
and mild steel angle frame with 2mm thick polyurethane sound damper as per SDRE
– Gratings & Manhole Covers
a) generally m2 413.35
2. Vehicular Grating
Mild steel grating in panels consisting of 100 x 75 x 9.4mm thick galvanised angle
frame with 65 x 9mm fish-tailed mild steel flat welded at 30mm centres and infilled
with 12mm diameter mild steel bars at 85mm centres, all joints and intersections
whole welded, drilled and including painting with one coat of inhibitive primer before
delivery, built into concrete surround as per SDRE – Gratings & Manhole Covers
a) generally for drains m2 1,284.35
Mild steel grating in panels consisting of 100 x 100 x 10mm thick galvanised mild
steel angle frame with fish-tail mild steel flat welded and infilled with 25 x 6 mild steel
flat at 30mm centres and 90 x 22mm mild steel flat at 85mm centres. The complete
assembly except fishtails are to be hot-dipped galvanised. All the flats and angles
are to be fillet welded throughout and drilled before delivery, built into concrete
surround as per SDRE – Gratings & Manhole Covers.
b) generally for manholes m2 1,256.60
3. Aluminium Rung
300 x 230mm aluminium rung as per SDRE – Drains & Culverts fixed to concrete
wall in drain including drilling and grouting with cement mortar (1:3)
a) 25mm diameter No 22.75
F. SURFACE TREATMENT
2. Plain Paving
Cement and sand (1:3) paving including trowelling smooth
a) average 20mm thick m2 15.00
b) average 25mm thick m2 17.40
c) average 32mm thick m2 18.55
20mm thick cement and sand (1:3) skirting with splayed or rounded top edge and
coved bottom including trowelling smooth
d) 100mm high m 7.00
e) 150mm high m 7.75
3. Hardened Paving
25mm thick cement and sand (1:3) paving mixed with hardener including trowelling
smooth
a) light duty non-metallic hardener (3kg per m2) m2 25.55
b) heavy duty non-metallic hardener (7kg per m2) m2 33.95
4. Granolithic Paving
Granolithic aggregate paving consisting of cement, sand and granite chippings of
5mm gauge (2:1:5) set out in panels with 15 x 15mm deep recessed joints laterally
at 1.20m centres including scrubbing to produce exposed aggregate finish
a) 25mm thick m2 40.00
5. Screed Bed
Cement and sand (1:3) screed to receive floor finishes
a) 20mm thick m2 16.00
b) 25mm thick m2 16.80
c) 32mm thick m2 17.50
VIII. PAINTING
A. PAINTING
2. Timber Surfaces
Painting timber surface
a) two coats of aluminium wood primer m2 6.45
b) two coats of stain and two coats of wax polish m2 9.20
c) two coats of varnish m2 10.00
d) one coat of aluminium wood primer, one undercoat and
two finishing coats of enamel paint m2 12.40
3. Metal Surfaces
Painting metal surface
a) one coat anti-rust paint, one undercoat and two coats of
aluminium paint m2 15.45
b) one coat of zinc chromate primer, one undercoat and
two finishing coats of synthetic enamel paint m2 15.25
4. Road Marking
One coat of 1.5mm thick thermoplastic paint on road pavement as per SDRE –
Road Markings & Signs
a) 100mm wide line m 6.15
b) 150mm wide line m 9.20
c) 200mm wide line m 12.45
d) 300mm wide line m 17.10
A. DRAINAGE WORK
1. Drain Excavation
Excavate trench minimum 340mm wide for 100mm diameter pipe, not exceeding
2.00m deep including backfilling and disposal of surplus excavated material
a) average 600mm deep m 17.05
b) average 1000mm deep m 24.25
c) average 1500mm deep m 50.70
Excavate trench minimum 490mm wide for 150mm diameter pipe including
temporary supports, backfilling and disposal of surplus excavated material
d) ne 2.00m deep, average 1.50m deep m 49.60
e) 2.00 - 4.00m deep, average 3.00m deep m 72.90
1. UPVC Pipes
Heavy duty unplasticised polyvinyl chloride Class C subsoil pipes 3/4 perforated
a) 100mm diameter m 31.85
b) 150mm diameter m 52.15
2. Filling Materials
a) Graded stone 20mm size m3 126.00
3. Drainage Layer
a) Geocomposite drainage layer as per SDRE – Drains &
Culverts m2 10.65
1. Pipe Culverts
Precast concrete pipe culverts Class 'L' complying with SS 183 butt jointed with
cement and sand (1:1) mortar
a) 300mm diameter m 50.35
b) 450mm diameter m 92.80
c) 600mm diameter m 138.95
d) 750mm diameter m 210.25
e) 900mm diameter m 264.20
f) 1,050mm diameter m 309.75
g) 1,200mm diameter m 376.75
h) 1,350mm diameter m 460.50
i) 1,500mm diameter m 577.20
Precast concrete pipe culverts Class 'M' complying with SS 183 butt jointed with
cement and sand (1:1) mortar
j) 300mm diameter m 75.55
k) 450mm diameter m 107.45
l) 600mm diameter m 151.75
m) 750mm diameter m 242.30
n) 900mm diameter m 314.75
o) 1,050mm diameter m 409.50
p) 1,200mm diameter m 438.50
q) 1,350mm diameter m 548.25
r) 1,500mm diameter m 699.20
2. Composite Channels
Precast concrete composite channel or block drains laid to even falls and jointed in
cement and sand (1:3) mortar
a) Type C1 m 7.95
b) Type C2 m 8.55
c) Type C3 m 10.70
d) Type C4 m 11.75
e) Type C5 m 12.70
f) Type C5A m 13.40
g) Type C6 m 19.15
h) Type C7R m 31.45
i) Type C7R1 m 33.30
j) Type C7A m 19.50
k) Type C7B m 19.35
l) Type C8 m 84.85
m) Type C8A m 63.55
n) Type C8B m 67.60
o) Type B1 m 22.80
p) Type B2 m 25.20
q) Type B3 m 67.55
Precast concrete channel laid in precast 'U' drain base sections or precast concrete
culverts including concrete grade 20 benching
r) Type C3 m 20.00
4. Weepholes
Supply and fix UPVC pipe to SS141 as weephole
a) 65mm diameter ne 300mm long No 2.95
b) 65mm diameter exc 300mm long m 4.50
c) 75mm diameter ne 300mm long No 3.20
d) 75mm diameter exc 300mm long m 5.20
E. SUNDRIES
2. Sump
Precast concrete sump for sub-soil drain including proper connections, concrete
benching and precast concrete cover slabs, internal size
a) 550 x 550 x 1300mm No 523.25
A. PAVEMENT
1. Sub-base
Supply and lay Sub-base material
a) generally m3 70.45
2. Base Course
Supply and lay Coarse granite aggregate (crusher-run) base course and blinded with
fine aggregate
a) generally m3 116.85
Supply and lay Graded granite aggregate base course
b) generally m3 93.55
Supply and lay Recycled concrete aggregate base (RCA) base
c) generally m3 50.00
3. Asphalt Concrete
Supply and lay hot-mix asphalt concrete base, binder or wearing course including
soluble bitumen
a) mix-specification type B1 ton 116.25
b) mix-specification type B1G ton 121.25
c) mix-specification type W1 ton 118.00
d) mix-specification type W3 ton 118.00
e) mix-specification type W3B ton 116.25
f) mix-specification type Open-graded ton 141.20
4. Sundries
Brush, sweep and thoroughly clean to remove all loose and superfluous materials
and ensure a perfectly dry surface prior to the application of the tack coat and
asphalt concrete
a) existing bitumen or concrete surfaces m2 0.35
Supply and lay tack coat of bitumen emulsion sprayed at a rate of 0.54 litre per m2
b) existing bitumen or concrete surfaces m2 0.95
A. STREET FURNITURE
1. Directional Signs
Single-face directional signs comprising aluminium sheeting 14SWG laminated with
approved reflective sheeting including all the required size of letters, numbers, logo(s)
and all necessary backings, welding and other types of connections as per SDRE –
Supports for Road Signs (supports to be measured separately)
a) Micro Prismatic Reflective Grade m2 1,061.35
Supports including foundation, excavation and disposal as per SDRE – Supports for
Road Signs
b) 75mm diameter cantilever supports (Type A) No 649.75
c) a pair of 100 x 100 x 6mm SHS supports (Type B) No 3,952.65
d) a pair of 120 x 120 x 8mm SHS supports (Type C) No 7,682.50
e) a pair of 150 x 150 x 6mm SHS supports (Type D) No 8,171.00
2. Traffic Signs
Single-faced silk screen traffic signs as regulatory signs, warning signs and
informative signs comprising 2mm thick aluminium sheets, approved Micro Prismatic
Grade reflective sheetings including appropriate diagrams, alphabets and numerals
(supports to be measured separately)
a) size 600 x 450mm No 214.00
b) size 600 x 600mm No 266.00
c) size 900 x 900mm No 411.05
d) other sizes m2 503.70
Supports for traffic signs
e) Supply and install 50 x 50 x 2.3mm thick galvanised square
hollow section vertical supports of traffic signs to all details as
shown in SDRE – Supports for Road Signs including excavation,
if any, and disposal of excavated materials from site, fixing and
fastening of maximum three traffic signs on any one face per
support, using 400 x 400 x 400mm concrete foundation with
built in expansion bolts No 133.15
Curved alignment marker comprising of 2mm thick aluminium sheets and approved
Mirco Prismatic Fluorescent Yellow reflective sheetings as per SDRE – Road
Markings and Signs
a) size 600 x 750mm (for arterial road) No 317.50
b) size 750 x 900mm (for expressway) No 510.00
B. SUNDRIES
1. Turfing
Turfing consisting of grass, size 300 x 300mm not less than 50mm thick, including
50mm thick topsoil and sludge (3:1) top dressing
a) spot turf on horizontal surface m2 8.30
b) close turf on embankment exceeding 15º from the
horizontal m2 9.90
3. Geotextile Membrane
Approved synthetic geotextile fabric membrane to pavement, troughs, french drains
etc. well lapped at joint (measured nett)
a) Type Class A m2 4.00
b) Type Class B m2 2.80
5. Paving Slabs
Precast concrete (grade 20) paving slab jointed and pointed in cement and sand (1:3)
including 50mm thick sand bed
a) size 300 x 300 x 50mm thick m2 55.65
6. Aeration Slabs
Precast concrete aeration slab of any pattern with top soil and turfing in voids
including 50mm thick sand bed
a) 65mm thick m2 46.50
b) 100mm thick m2 52.05