Escolar Documentos
Profissional Documentos
Cultura Documentos
Load Cell
DESCRIPTION
Model 101 load cells is engineered to measure bending
forces and still achieve an impressive 0.02 % accuracy. Small
dimensions allow easy unit integration into existing systems.
Model 101 uses foil gages and is available for load ranges from
50 grams to 1000 pounds.
FEATURES
• 50 kg to 1000 kg range
• ±0.02 % accuracy
• Integral cable
• Cost efficient
• One-piece, nickel-plated alloy steel construction
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 101
ENVIRONMENTAL SPECIFICATIONS
MOUNTING DIMENSIONS
Characteristic Measure
Temperature, operating -30 °C to 70 °C [-22 °F to 158 °F] Load (kg) H mm [in] Recommended bolt
torque (N-m)
Temperature, compensated -20 °C to 55 °C [-4 °F to 130 °F]
50 to 2250 18 [0.71] 60
Temperature effect, zero 0.02 % full scale/10 °C
500, 1000 24 [0.94] 60
Temperature effect, span 0.02 % full scale/10 °C
ELECTRICAL SPECIFICATIONS
Characteristic Measure
Strain gage type Bonded foil
Excitation (calibration) 10 Vdc to 12 Vdc
Excitation (max.) 15 Vdc
Insulation resistance >5000 mOhm
Bridge resistance (toler- 400 ohm ±10 ohm (nominal)
ance) - input resistance
Bridge resistance (toler- 352 ohm ±2 ohm (nominal)
ance) - output resistance
Zero balance (tolerance) ±1 % full scale
Electrical termination (std) 3 m flying leads
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % full scale1
Material Nickel plated alloy steel
Deflection < 2 mm
WIRING CODES
Cable
Red (+) supply
Black (-) supply
Green (+) output
White (-) output
Large black shield
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 102
Load Cell
DESCRIPTION
The Model 102 load cells combines both a compact form and
high precision to offer a superior tension force transducer. The
one-piece S-shaped design achieves a maximum non-linearity
of 0.02 % full scale for load ranges from 20 kg to 1000 kg.
Additional features include minimal temperature effects on zero
and span of 0.002 %/°C and 0.002 %/°C, respectively.
FEATURES
• 20 kg to 1000 kg range
• ±0.02 % accuracy
• One-piece, nickel-plated alloy steel construction
• Integral cable
• Cost efficient
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 102
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 full scale1
Material Nickel plated alloy steel or stainless
steel
Deflection Less than or equal to 0,5 mm [0.02 in]
WIRING CODES
Cable
Red (+) supply
Black (-) supply
Green (+) output
White (-) output
Large Black Shield
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 102 Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads – maximum load to be applied without
damage.2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. This unit is calibrated to Metric (non-Imperial) units.
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
TYPICAL SYSTEM DIAGRAM of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 103
Load Cell
DESCRIPTION
Model 103 load cell is engineered to measure bending forces
and still achieve an impressive 0.02% full scale accuracy. Small
dimensions allow easy unit integration into existing systems.
Model 103 uses foil gages and is available for load ranges from
100 kg to 10000 kg.
FEATURES
• Low cost
• 100 kg to 10000 kg range
• ±0.02 % accuracy
• Integral cable
• Cost efficient
• One-piece, nickel-plated alloy steel construction
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 103
ELECTRICAL SPECIFICATIONS
Characteristic Measure
Strain gage type Bonded foil
Excitation (calibration) 10 Vdc to 12 Vdc
Excitation (max.) 15 Vdc
Insulation resistance >5000 mOhm
Bridge resistance (toler- 400 ohm ±10 ohm (nominal)
ance) - input resistance
Bridge resistance (toler- 352 ohm ±2 ohm (nominal)
ance) - output resistance
Zero balance (tolerance) ±1 % full scale
Electrical termination (std) 3 m flying leads
100 kg to 300 kg
Electrical termination (std) 5 m flying leads
1000 kg to 5000 kg
Electrical termination (std) 8 m flying leads
10000 kg
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % full scale1
Material Nickel plated alloy steel
Deflection < 1,5 mm
WIRING CODES
Cable
Red (+) supply
Black (-) supply
Green (+) output
White (-) output
Large black shield
MOUNTING DIMENSIONS
Load A mm B mm C mm D mm E mm F mm G mm H mm L mm M mm Recom-
(kg) [in] [in] [in] [in] [in] [in] [in] [in] [in] [in] mended
bolt
torque
(N-m)
100 to 135 [5.31] 36 [1.42] 26 [1.02] 18 [0.71] 75 [2.95] 25 [1.0] 32 [1.26] 58 [2.28] 11,5 11,5 60
300 [0.45] [0.45]
500 to 135 [5.31] 38 [1.5] 30 [1.18] 18 [0.71] 75 [2.95] 25 [1.0] 34 [1.34] 58 [2.28] 13,5 13,5 100
2000 [0.53] [0.53]
300 to 170 [6.69] 48 [1.89] 38 [1.5] 20 [0.79] 85 [3.35] 50 [2.0] 39 [1.54] 79 [3.11] 18 [0.71] 18,5 255
5000 [0.73]
10000 263 60 [2.36] 60 [2.36] 30 [1.18] 118 [4.65] 90 [3.54] 52 [2.05] 134 [5.28] 26 [1.02] 26 [1.02] 860
[10.35]
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 123
Load Cell
DESCRIPTION
The Model 123 load cells combines both a compact form and
high precision to offer a superior tension force transducer. The
one-piece S-shaped design achieves a maximum non-linearity of
0.03 % full scale for load ranges from 1000 kg to 20000 kg.
FEATURES
• 1000 kg to 20000 kg range
• ±0.03 % accuracy
• Built-in overload resistance
• One-piece, nickel-plated alloy steel construction
• Integral cable
• Cost efficient
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 123
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 120 % full scale1
Later load limit 100 % full scale
Material Nickel plated alloy steel
WIRING CODES
Cable
Red (+) supply
Black (-) supply
Green (+) output
White (-) output
Large Black Shield
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 123 Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads – maximum load to be applied without
damage.2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. IP68 rating for load ranges 7500 kg and greater.
4. This unit is calibrated to Metric (non-Imperial) units. or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
TYPICAL SYSTEM DIAGRAM of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 125
Load Cell
DESCRIPTION
The Model 125 load cells combines both a compact form and
high precision to offer a superior tension force transducer. The
one-piece S-shaped design achieves a maximum non-linearity of
0.03 % full scale for load ranges from 100 kg to 500 kg.
FEATURES
• 100 kg to 500 kg range
• ±0.02 % accuracy
• One-piece, nickel-plated alloy steel construction
• Mating connector and 5 m cable included
• Cost efficient
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 125
ENVIRONMENTAL SPECIFICATIONS
Characteristic Measure MOUNTING DIMENSIONS
Temperature, operating -30 °C to 70 °C [-22 °F to 158 °F]
Temperature, compensated -20 °C to 55 °C [-4 °F to 131 °F]
Temperature effect, zero ±0.02 % full scale/10 °C
Temperature effect, span ±0.02 % full scale/10 °C
Protection class IP67
ELECTRICAL SPECIFICATIONS
Characteristic Measure
Strain gage type Bonded foil
Excitation (acceptable) 10 Vdc to 12 Vdc
Excitation (max.) 15 Vdc
Insulation resistance > 5000 mOhm
Bridge resistance (toler- 400 ohm ±10 ohm (nominal)
ance) - Input resistance
Bridge resistance (toler- 352 ohm ±2 ohm (nominal)
ance) - Output resistance
Zero balance (tolerance) ±1 % full scale
Electrical termination (std) Mating connector and 5 m [16.40 ft]
cable (included)
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % FS1
Material Nickel plated alloy steel
WIRING CODES
Cable
Red (+) supply
Black (-) supply
Green (+) output
White (-) output
Large Black Shield
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 125 Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads – maximum load to be applied without
damage.2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. This unit is calibrated to Metric (non-Imperial) units.
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
TYPICAL SYSTEM DIAGRAM of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 127
Load Cell
DESCRIPTION
The Model 127 load cells combines both a compact form and
high precision to offer a superior tension force transducer. The
one-piece S-shaped design achieves a maximum non-linearity of
0.03 % full scale for load ranges of 50 kg and 100 kg.
FEATURES
• 50 kg, 100 kg range
• ±0.03 % FS accuracy
• Built-in overload resistance
• One-piece, nickel-plated alloy steel construction
• Integral cable
• Cost efficient
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 127
ENVIRONMENTAL SPECIFICATIONS
Characteristic Measure
Temperature, operating -30 °C to 70 °C [-22 °F to 158 °F]
Temperature, compensated -20 °C to 55 °C [-4 °F to 131 °F]
Temperature effect, zero ±0.03 % full scale/10 °C
Temperature effect, span ±0.03 % full scale/10 °C
Protection class IP67
ELECTRICAL SPECIFICATIONS
Characteristic Measure
Strain gage type Bonded foil
Excitation (acceptable) 10 Vdc to 12 Vdc
Excitation (max.) 15 Vdc
Insulation resistance > 5000 mOhm
Bridge resistance (toler- 400 ohm ±10 ohm (nominal)
ance) - Input resistance
Bridge resistance (toler- 352 ohm ±2 ohm (nominal)
ance) - Output resistance
Zero balance (tolerance) ±1 % full scale
Electrical termination (std) 5 m [16.40 ft] flying leads
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % full scale1
Material Nickel plated alloy steel
WIRING CODES
Cable
Red (+) supply
Black (-) supply
Green (+) output
White (-) output
Large Black Shield
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 127 Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads – maximum load to be applied without
damage.2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. This unit is calibrated to Metric (non-Imperial) units.
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
TYPICAL SYSTEM DIAGRAM of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 129
Load Cell
DESCRIPTION
The Model 129 load cells combines both a compact form and
high precision to offer a superior tension force transducer. The
one-piece S-shaped design achieves a maximum non-linearity of
0.02 % full scale for load ranges from 1000 kg to 5000 kg.
FEATURES
• 1000 kg to 5000 kg range
• ±0.02 % accuracy
• One-piece, nickel-plated alloy steel construction
• Integral cable
• Cost efficient
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 129
ENVIRONMENTAL SPECIFICATIONS
Characteristic Measure MOUNTING DIMENSIONS
Temperature, operating -30 °C to 70 °C [-22 °F to 158 °F]
Temperature, compensated -20 °C to 55 °C [-4 °F to 131 °F]
Temperature effect, zero ±0.02 % full scale/10 °C
Temperature effect, span ±0.02 % full scale/10 °C
Protection class IP67
ELECTRICAL SPECIFICATIONS
Characteristic Measure
Strain gage type Bonded foil
Excitation (acceptable) 10 Vdc to 12 Vdc
Excitation (max.) 15 Vdc
Insulation resistance > 5000 mOhm
Bridge resistance (toler- 400 ohm ±10 ohm (nominal)
ance) - Input resistance
Bridge resistance (toler- 352 ohm ±2 ohm (nominal)
ance) - Output resistance
Zero balance (tolerance) ±1 % full scale
Electrical termination (std) 5 m [16.40 ft] flying leads
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % FS1
Material Nickel plated alloy steel
WIRING CODES
Cable
Red (+) supply
Black (-) supply
Green (+) output
White (-) output
Large Black Shield
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 129 Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads – maximum load to be applied without
damage.2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. This unit is calibrated to Metric (non-Imperial) units.
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
TYPICAL SYSTEM DIAGRAM of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 53
Low Cost Load Cell
DESCRIPTION
Model 53 load cells are bonded foil strain gage transducers term stability and reliability under severe operating conditions.
designed for cost efficient production and testing applications The Model 53 compression-only load cell has an integral load
(i.e. press calibration). Engineered compression force button machined as part of the load cell. The Model 53 must be
measurements up to 50000 lb., this model achieves a maximum mounted on a smooth flat surface for proper operation. Three
non-linearity of 0.25 % full scale. Precision gaging techniques tapped holes are provided for mounting.
and a stainless steel construction provides excellent long-
FEATURES
• 5 lb to 50000 lb
• Stainless steel
• Mini footprint
• Button-style design
• mV/V output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 53
PERFORMANCE SPECIFICATIONS RANGE CODES
Characteristic Measure Range Available ranges Range Available ranges
Load ranges5 5 lb to 50000 lb Code Code
Linearity (max.) ±0.25 % full scale AT 5 lb DN 3000 lb
WIRING CODES
Cable Unamplified
Red (+) excitation
Black (-) excitation
Green (-) output
White (+) output
3000, 4000, 5000, 38,1 [1.50] 10,16 [0.40] 16,0 [0.63] 2,03 [0.08] #6-32 UNC 6,35 [0.25] 31,75 [1.250]
7500, 10000
15000, 20000, 30000 50,8 [2.00] 15,24 [0.60] 25,4 [1.00] 3,05 [0.12] #6-32 UNC 6,35 [0.25] 41,28 [1.625]
50000 76,2 [3.00] 19,81 [0.78] 38,1 [1.50] 4,57 [0.18] #6-32 UNC 6,35 [0.25] 60,33 [2.375]
OPTION CODES
Many range/option combinations are available in
our quick-ship and fast-track manufacture pro-
grams. Please see http://sensing.honeywell.com/
TMsensor-ship for updated listings.
Load 5, 10, 25, 50, 100, 250, 500, 1000, 2000, 3000, 4000,
ranges 5000, 7500, 10000, 15000, 20000, 30000, 50000 lb
Tempera- 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F
ture com- 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F
pensation 1c. 0 °F to 185 °F 1i. -65 °F to 250 °F
1d. -20 °F to 130 °F 1j. 0 °C to 50 °C
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
1f. 70 °F to 250 °F 1m. -25 °C to 110 °C
Internal 2u. Unamplified, mV/V output
amplifiers
Electrical 6d. Microtec DR-4S-4H 4-pin 6h. Integral cable:
termination 6e. Integral cable: Teflon Silicone
6f. Integral cable: PVC 6i. Integral underwa-
6g. Integral cable: Neoprene ter cable3
6v. Phoenix connector
on end of cable
Special 9a. 10 point (5 up/5 down) 20 % increments @ 68 °F
calibration 9b. 20 point (10 up/10 down) 10 % increments @ 68 °F
Shock and 44a. Shock and vibration resistance
vibration
Interfaces 53e. Signature calibration6
53t. TEDS IEEE 1451.4 module4
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this datasheet is for
reference only. DO NOT USE this document as product
Find out more installation information.
Honeywell serves its customers • Complete installation, operation and maintenance
through a worldwide network of information is provided in the instructions supplied with
each product.
sales offices, representatives
Failure to comply with these instructions could result in
and distributors. For application
death or serious injury.
assistance, current specifica-
tions, pricing or name of the
nearest Authorized Distributor,
contact your local sales office.
To learn more about Honeywell’s
test and measurement products,
call +1-614-850-5000, visit
www.honeywell.com/sensotec,
or e-mail inquiries to
info.tm@honeywell.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 41
Precision Low Profile Load Cell
DESCRIPTION
Model 41 is a low profile “pancake” type load cells. These reduce off-center and side-loading effects. It provides high
bonded foil, strain gage load cells are engineered to measure performance in non-linearity, hysteresis, and repeatability speci-
loads from 5 lb to 500,000 lb. The tension/ compression fications for such applications as tube mills, extruding processes
Model 41 is designed with the threaded hole running completely and weighing. Each unit has a welded construction and can be
through the center of the cell. Model 41 utilizes two stabilizing hermetically sealed for added durability. Model 41 load cells are
diaphragms, which are welded to the sensing member to available with optional 0 Vdc to 5 Vdc or 4 mA to 20 mA output.
FEATURES
• 0.1 % accuracy
• 5 lb to 500000 lb
• mV/V output (standard); 4 mA to 20 mA and 0 Vdc to 5 Vdc
(optional) outputs
• Double diaphragm design
• Intrinsically safe available (2N option only)16
• CE approved17
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 41
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Precision Low Profile Load Cell
iNTERNAL AMPLIFIERS
Current two- Intrinsically
Amplifier Voltage out- Voltage out- Voltage out- Current three-
wire: Option safe amp: Op-
specifications put: Option 2b put: Option 2c put: Option 2t wire: Option 2j
2k tion 2n (2N)***
Output signal ±5 V 0-5 V or ±5 V @ 0-10 V or ±10 V 4 mA to 20 mA 4 mA to 20 mA 4 mA to 20 mA
45 mA @ 45 mA
Input power (voltage) ±15 Vdc or 26-32 11 Vdc to 28 Vdc 15 Vdc to 28 Vdc 22 Vdc to 32 Vdc 15 Vdc to 9 Vdc to
Vdc 40 Vdc 28 Vdc
Input power (current) 45 mA 40 mA 40 mA 65 mA 4 mA to 28 mA 4 mA to 24 mA
Freq. response 3000 Hz 3000 Hz 3000 Hz 2500 Hz 300 Hz 2000 Hz
Power supply rejection 60 db 60 db 60 db 60 db 60 db 60 db
Operating temperature -20 °F to 185 °F -20 °F to 185 °F -20 °F to 185 °F 0 °F to 185 °F 0 °F to 185 °F -20 °F to 185 °F
Reverse volt. protection Yes Yes Yes Yes Yes Yes
Short circuit protection Momentary Momentary Momentary Yes Yes Yes
Wiring code: connector A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply
B Output common B Output common** B Output common** B Output common** B No connection B No connection
C Supply return C Supply return** C Supply return** C Supply return** C No connection C No connection
D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output
E Shunt Cal 1 E Shunt Cal 1 E Shunt Cal 1 E Shunt Cal 1 E Case ground E Case ground
F Shunt Cal 2 F Shunt Cal 2 F Shunt Cal 2 F Shunt Cal 2 F No connection F No connection
Wiring code: cable R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
Bl Output common Bl Output com* Bl Output com* Bl Output com* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt Cal 1 B Shunt Cal 1 B Shunt Cal 1 B Shunt Cal 1
Br Shunt Cal 2 Br Shunt Cal 2 Br Shunt Cal 2 Br Shunt Cal 2
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 41
OPTION CODES
Many range/option combinations are available in our quick-ship and fast-track manufacture programs.
Please see http://sensing.honeywell.com/TMsensor-ship for updated listings.
Load ranges 5, 10, 25, 50, 100, 250, 500, 1000, 2000, 5000, 3000, 4000, 7500, 10000, 15000, 20000, 30000, 50000, 75000, 100000, 150000,
200000, 300000, 400000, 500000 lb
Temperature 1a. 60 °F to 160 °F 1d. -20 °F to 130 °F 1g. 70 °F to 325 °F14 1j. 0 °C to 50 °C
compensation 1b. 30 °F to 130 °F 1e. -20 °F to 200 °F 1h. 70 °F to 400 °F14 1k. -20 °C to 85 °C
1c. 0 °F to 185 °F 1f. 70 °F to 250 °F 1i. -65 °F to 250 °F14 1m. -25 °C to 110 °C
Internal 2b. 4 wire, ±5 Vdc 2j. 4-20 mA (three-wire) 2n (2N) 4 mA to 20 mA (wire) 2u. Unamplified, mV/V output
amplifiers 10 2c. 0-5 Vdc output output intrinsically safe20
2k. 4 mA to 20 mA (two- 2t. 0 Vdc to 10 Vdc
wire)20
Internal ampli- 3a. Input/output isolation19
fier enhance- 3d. Remote buffered shunt calibratrion8
ments
Overload 4a. Overload stops
stops
Electrical 6a. Bendix PTIH-10-6P 6-pin 6f. Integral cable: PVC 6i. Integral underwater 6q. Molded integral cable poly-
termination (ranges to 5000 lb) 6g. Integral cable: Neo- cable9 urethane9
6b. MS3102E-14S-6P (rang- prene9 6j. 1/2-14 conduit fitting with 6v. Phoenix connector on end of
es 7500 lb and up)9 6h. Integral cable: Silicone 5 ft of 4 conductor PVC cable
6e. Integral cable: Teflon cable
Shunt calibra- 8a. Precision internal resistor14
tion
Special cali- 9a. 10 point (5 up/5 down) 20 % increments @ 68 °F
bration 9b. 20 point (10 up/10 down) 10 % increments @ 68 °F
9c. ASTM E-74 calibration
Bridge resist- 12b. 5000 ohm (foil)
ance
Zero and span 14a. No access to pots
adjustment 14b. Top access to pots
Electrical con- 15a. Horizontal electrical exit port orientation 15c. Radial electrical exit port orientation
nector orienta- 15b. Vertical electrical exit port orientation 15d. Connector on end of cable
tion
Special cali- 30a. Compression only calibration, positive in compression
bration 30b. Tension and compression calibration, positive in tension
30c. Compression only calibration, negative in compression
30d. Tension and compression calibration, positive in compression
Bridge type 31a. Dual bridge
Shock and 44a. Shock and vibration resistance
vibration
Interfaces 53e. Signature calibration14
53t. TEDS IEEE 1451.4 module15
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Precision Low Profile Load Cell
MOUNTING DIMENSIONS
Ranges D mm H mm H*** F# ØG ØK mm T A mm A* mm B mm B* mm C mm
lb [in] [in] mm mm [in] [in] [in] [in] [in] [in] [in]
[in] B.C. thru
5, 10, 25 63,5 20,32 44,45 6 50,8 4,83 1/4-28 20,83 63,5 19,05 22,86 31,75
[2.50] [0.80] [1.75] [2.000] [0.19] UNF [0.82] [2.5] [0.75] [0.9] [1.25]
50, 100, 76,2 25,4 44,45 6 57,15 7,11 3/8-24 20,83 63,5 19,05 22,86 31,75
250, 500, [3.00] [1.00] [1.75] [2.250] [0.28] UNF [0.82] [2.5] [0.75] [0.9] [1.25]
1000
2000, 88,9 25,4 44,45 6 66,68 8,64 1/2-20 20,83 63,5 19,05 22,86 31,75
3000, [3.50] [1.00] [1.75] [2.625] [0.34] UNF [0.82] [2.5] [0.75] [0.9] [1.25]
4000,
5000
7500, 139,7 45,7 45,7 8 114,3 10,16 1-14 31,75 58,42 38,1 38,1 50,8
10000, [5.50] [1.80] [1.80] [4.500] [0.40] UNS [1.25] [2.3] [1.50] [1.5] [2.00}
15000
20000, 152,4 45,7 45,7 8 123,83 13,46 1 1/2-12 31,75 58,42 38,1 38,1 50,8
30000, [6.00] [1.80] [1.80] [4.875] [0.53] UNF [1.25] [2.3] [1.50] [1.5] [2.00}
50000
75000, 228,6 63,5 63,5 12 196,85 16,76 2-12 UN 31,75 58,42 38,1 38,1 50,8
100000 [9.00] [2.50] [2.50] [7.750] [0.66] [1.25] [2.3] [1.50] [1.5] [2.00}
150000, 279,4 63,5 63,5 12 241,3 19,81 2 1/2-12 31,75 58,42 38,1 38,1 50,8
200000 [11.00] [2.50] [2.50] [9.500] [0.78] UN [1.25] [2.3] [1.50] [1.5] [2.00}
300000, 355,6 107,95 107,95 12 298,45 26,16 3 1/2-8 31,75 58,42 38,1 38,1 **
400000, [14.00] [4.25] [4.25] [11.750] [1.03] UN [1.25] [2.3] [1.50] [1.5]
500000
* Length of load cell with amplified option (see option codes)
** C dimension varies on high ranges. Consult factory
*** H dimension with 2n(2N) amplifier
TYPICAL SYSTEM DIAGRAM
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 41 Precision Low Profile Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads - maximum load to be applied without
damage.2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed with specific warranty details. If warranted goods are returned to
safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. Interconnecting shunt cal. 1 terminal with shunt cal. 2 terminal pro-
vides 50 % (unamplified units), 75 % (4 mA to 20 mA 3-wire units) or or replace, at its option, without charge those items it finds
80 % (voltage amplified units) of full scale output for quick calibration. defective. The foregoing is buyer’s sole remedy and is in lieu
Shunt calibration comes standard with internal amplifier option 2b, 2c,
2t and 2j. of all warranties, expressed or implied, including those of
4. O=Orange; Y=Yellow; B=Blue; Bl=Black; R=Red; Br=Brown; merchantability and fitness for a particular purpose. In no
W=White; G=Green. Color specifying cable and number or letter
specifying connector.
event shall Honeywell be liable for consequential, special, or
5. No mating connector necessary for cable option. indirect damages.
6. Adding any internal amplifiers on 5 lb to 25 lb ranges will increase
delivery time. While we provide application assistance personally, through our
7. Option 2n (2N) on 5 to 5000 lb. ranges will typically take 12 weeks for literature and the Honeywell web site, it is up to the customer to
delivery.
8. Option 3d is not available with option 2n (2N) or 2k. determine the suitability of the product in the application.
9. Not available with option 1c, 1e, 1f, 1g, 1h or 1i.
10.Consult factory. Specifications may change without notice. The information we
11.Availability varies with range, consult factory. supply is believed to be accurate and reliable as of this printing.
12.Option only pertinent when option 2n (2N) selected. However, we assume no responsibility for its use.
13.Standard calibration for tension/compression load cells is in tension
only. For more information about Sensing and Control products, visit
14.Not available with amplified output.
15.Consult factory for TEDS availability with amplified models. www.honeywell.com/sensing or call +1-815-235-6847
16.Range dependent; consult factory. Termination dependent; consult Email inquiries to info.sc@honeywell.com
factory.
17.Internal amp and termination dependent; consult factory.
18.This unit calibrated to Imperial (non-Metric) units. WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 43
Precision Low Profile Load Cell
DESCRIPTION
Model 43 is a low profile “pancake” type load cells. These bond- applications as tube mills, extruding processes and weighing.
ed foil, strain gage load cells are engineered to measure loads Each unit has a welded construction and can be hermetically
from 5 lb to 500,000 lb. The compression-only Model 43 has a sealed for added durability. Model 43 is available with optional 0
load button which is fixed as an integral part of the load cell and Vdc to 5 Vdc or 4 mA to 20 mA output.
cannot be removed or changed. It provides high performance in
non-linearity, hysteresis, and repeatability specifications for such
Approved Approved Approved
Intrinsically safe amp
FEATURES
• 0.10 % accuracy
• 5 lb to 500000 lb
• mV/V output (standard); 0 Vdc to 5 Vdc or 4 mA to 20 mA
(optional)
• Stainless steel
• Double diaphragm design
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 43
Zero balance (tolerance) ±1 % full scale 7500 to 30000 0.003 9000 2.90 [6.4]
Shunt calibration data Included 50000 to 100000 0.004 13000 2.99 [6.6]
Electrical termination (std) PTIH-10-6P 150000 to 200000 0.004 11000 5.31 [11.7]
5 lb to 5000 lb 300000 0.005 10000 10.8 [23.8]
Electrical termination (std) MS3102E-14S-6P 400000 0.007 8400 12.02
7500 lb to 500000 lb [26.5]
Mating connector PT06A-10-6S or equiv. (AA111) 500000 0.007 4800 41.00
5 lb to 5000 lb (not incl.) [90.4]
Mating connector MS3106A-14S-6S (AA121)
7500 to 500000 lb (not incl.)
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Precision Low Profile Load Cell
INTERNAL AMPLIFIERS
Current two- Intrinsically
Amplifier Voltage out- Voltage out- Voltage out- Current three-
wire: Option safe amp: Op-
specifications put: Option 2a put: Option 2c put: Option 2t wire: Option 2j
2k tion 2n (2N)***
Output signal 0 V to 5 V 0 V to 5 V or ±5 V 0 V to 10 V or 4 mA to 20 mA 4 mA to 20 mA 4 mA to 20 mA
@ 45 mA ±10 V @ 45 mA
Input power (voltage) ±15 V or 26 Vdc 11 Vdc to 28 Vdc 15 Vdc to 28 Vdc 22 Vdc to 32 Vdc 15 Vdc to 9 Vdc to
to 32 Vdc 40 Vdc 28 Vdc
Input power (current) 45 mA 40 mA 40 mA 65 mA 4 mA to 28 mA 4 mA to 24 mA
Freq. resp (amp) 3000 Hz 3000 Hz 3000 Hz 2500 Hz 300 Hz 2000 Hz
Power supply rej. 60 db 60 db 60 db 60 db 60 db 60 db
Operating temp. -20 °F to 185 °F -20 °F to 185 °F -20 °F to 185 °F 0 °F to 185 °F 0 °F to 185 °F -20 °F to 185 °F
Reverse voltage protec- Yes Yes Yes Yes Yes Yes
tion
Short cir. protection Momentary Momentary Momentary Yes Yes Yes
Wiring code: connector A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply
(std)4 B Output common B Output common** B Output common** B Output common** B No connection B No connection
C Supply return C Supply return ** C Supply return** C Supply return** C No connection C No connection
D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output
E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Case ground E Case ground
F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F No connection F No connection
Wiring code: cable4,5,6 R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
* Black and green wires are internally connected.
** Pins B and C are internally connected.
*** See our Web site for the most up-to-date information regarding intrinsically safe approvals, ref. #008-0547-00.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 43
OPTION CODES
Many range/option combinations are available in our quick-ship and fast-track manufacture programs.
Please see http://sensing.honeywell.com/TMsensor-ship for updated listings.
Load ranges 5, 10, 25, 50, 100, 250, 500, 1000, 2000, 3000, 4000, 5000, 7500, 10000, 15000, 20000, 30000, 50000, 75000, 100000,
150000, 200000, 300000, 400000, 500000 lb
Temperature 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F11
compensation 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F11
1c. 0 °F to 185 °F 1i. -65 °F to 250 °F
1d. -20 °F to 130 °F 1j. 0 °C to 50 °C
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
1f. 70 °F to 250 °F 1m. -25 °C to 110 °C
Internal 2a. Four wire, 0 Vdc to 5 Vdc output 2n (2N) 4 mA to 20 mA (two-wire) intrinsically safe10
amplifiers 2c. 0 Vdc to 5 Vdc 2t. 0 Vdc to 10 Vdc output
2j. 4 mA to 20 mA (three-wire) output 2u. Unamplified, mV/V output
2k. 4 mA to 20 mA (two-wire)10
Internal amplifier 3a. Input/output isolation7
enhancements 3d. Remote buffered shunt calibration8
Electrical 6a. Bendix PTIH-10-6P (or equivalent), 6-pin (max. 250 °F) 6f. Integral cable: PVC
termination 6b. MS connector MS3102E-14S-6P (mates with MS3106E- 6g. Integral cable: Neoprene
14S-6S) (max. 160 °F) (ranges above 5000 lb)12 6h. Integral cable: Silicone
6e. Integral cable: Teflon 6i. Integral underwater cable
6j. 1/2-14 conduit fitting with 5 ft of 4 conductor PVC cable
Shunt 8a. Precision internal resistor11
calibration
Special 9a. 10 point (5 up/5 down) 20 % increments @ 70 °F
calibration 9b. 20 point (10 up/10 down) 10 % increments @ 70 °F
9c. ASTM E-74 calibration
Bridge 12. 5000 ohm (foil) (max. 250 °F)
resistance
Bridge type 31a. Dual bridge
Zero and span 14a. No access to pots
adjustment 14b. Top access to pots
Electrical 15a. Horizontal electrical exit port orientation
connector 15b. Vertical electrical exit port orientation
orientation 15c. Radial electrical exit port orientation
15d. Connector on end of cable
Special 30a. Compression only, positive output
calibration
Shock and 44a. Shock and vibration resistance
vibration
Interfaces 53e. Signature calibration11
53t. TEDS IEEE 1451.4 module8
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Precision Low Profile Load Cell
MOUNTING DIMENSIONS
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 43 Precision Low Profile Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. 0.12 mm [3.00 in] diameter has six mounting holes.
2. Allowable maximum loads - maximum load to be applied without Honeywell’s standard product warranty applies unless agreed
damage.3 to otherwise by Honeywell in writing; please refer to your
3. Without damage - loading to this level will not cause excessive zero
shift or performance degradation. The user must consider fatigue order acknowledgement or consult your local sales office for
life for long term use and structural integrity. All structurally critical specific warranty details. If warranted goods are returned to
applications (overhead loading, etc.) should always be designed
with safety redundant load paths. Honeywell during the period of coverage, Honeywell will repair
4. Interconnecting shunt cal. 1 terminal with shunt cal. 2 terminal or replace, at its option, without charge those items it finds
provides 50 % (unamplified units), 75 % (4 mA to 20 mA three-wire
defective. The foregoing is buyer’s sole remedy and is in lieu
units) or 80 % (voltage amplified units) of full scale output for quick
calibration. Shunt calibration comes standard of all warranties, expressed or implied, including those of
with internal amplifier option 2a, 2b, 2c, 2t and 2j. merchantability and fitness for a particular purpose. In no
5. O=Orange; Y=Yellow; B=Blue; Bl=Black; R=Red; Br=Brown;
W=White; G=Green. Color specifying cable and number or letter event shall Honeywell be liable for consequential, special, or
specifying connector indirect damages.
6. No mating connector necessary for cable option.
7. Only available with option 2a or 2c. While we provide application assistance personally, through our
8. Consult factory for TEDS availability with amplified models.
9. This unit calibrated to Imperial (non-Metric) units. literature and the Honeywell web site, it is up to the customer to
10. 5000 ohm bridge required. determine the suitability of the product in the application.
11. Cannot be used with amplified option.
12. Cannot be used with options 1c, 1e, 1f, 1g, 1h, or 1i. Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 75
Precision Low Profile Load Cell
DESCRIPTION
Model 75 fatigue rated load cells are engineered for applications Model 75 measures tension/compression and must be used on a
such as materials or product fatigue testing, which involve an smooth flat surface to achieve rated specifications. The tension/
extremely large number of cycles or occasional overload condi- compression Model 75 is designed with the threaded hole run-
tions. These fatigue rated load cells have load ranges from 50 lb ning completely through the center of the cell. Model 75 utilizes
to 200,000 lbs and achieve a non-linearity of 0.1% full scale. The two stabilizing diaphragms, which are welded to the sensing
superior design of these bonded foil, strain gage compression member to reduce off-center and side-loading effects.
and/or tension load cells permits a fatigue life of 1 billion cycles
(zero to full scale).
FEATURES
• 0.10 % accuracy
• 50 lb to 200000 lb
• mV/V output (standard); 4 mA to 20 mA or 0 Vdc to 5 Vdc
(optional) outputs
• Stainless steel
• Double diaphragm design
• Enhanced overload capacity
• Intrinsically safe available (2N option only)8
• CE approved9
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 75
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 200 % FS 2
Weight See table
Material < 100000 lb 17-4PH stainless steel
Material > 125000 lb Carbon steel
Life cycles (approx.) > 108 cycles fully reversed
Deflection See table
Natural frequency See table
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Precision Low Profile Load Cell
INTERNAL AMPLIFIERS
Current two- Intrinsically
Amplifier Voltage out- Voltage out- Voltage out- Current three-
wire: Option safe amp: Op-
specifications put: Option 2b put: Option 2c put: Option 2t wire: Option 2j
2k tion 2n (2N)***
Output signal ±5 V 0 V to 5 V or ±5 V 0 V to 10 V or 4 mA to 20 mA 4 mA to 20 mA 4 mA to 20 mA
@ 45 mA ±10 V @ 45 mA
Input power (voltage) ±15 V or 26 Vdc 11 Vdc to 28 Vdc 15 Vdc to 28 Vdc 22 Vdc to 32 Vdc 15 Vdc to 9 Vdc to
to 32 Vdc 40 Vdc 28 Vdc
Input power (current) 45 mA 40 mA 40 mA 65 mA 4 mA to 28 mA 4 mA to 24 mA
Freq. resp (amp) 3000 Hz 3000 Hz 3000 Hz 2500 Hz 300 Hz 2000 Hz
Power supply rej. 60 db 60 db 60 db 60 db 60 db 60 db
Operating temp. -20 °F to 185 °F -20 °F to 185 °F -20 °F to 185 °F 0 °F to 185 °F 0 °F to 185 °F -20 °F to 185 °F
Reverse voltage protec- Yes Yes Yes Yes Yes Yes
tion
Short cir. protection Momentary Momentary Momentary Yes Yes Yes
Wiring code: connector A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply
(std)4 B Output common B Output common** B Output common** B Output common** B No connection B No connection
C Supply return C Supply return ** C Supply return** C Supply return** C No connection C No connection
D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output
E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Case ground E Case ground
F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F No connection F No connection
Wiring code: cable4,5,6 R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 75
OPTION CODES
Many range/option combinations are available in our quick-ship and fast-track manufacture programs.
Please see http://sensing.honeywell.com/TMsensor-ship for updated listings.
Load ranges 50, 100, 250, 500, 1000, 2000, 3000, 4000, 5000, 7500, 10000, 15000, 20000, 30000, 50000, 75000, 150000, 200000 lb
Temperature 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F13
compensation 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F13
1c. 0 °F to 185 °F 1i. -65 °F to 250 °F13
1d. -20 °F to 130 °F 1j. 0 °C to 50 °C
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
1f. 70 °F to 250 °F 1m. -25 °C to 110 °C
Internal 2b. Four wire, ±5 Vdc output 2n (2N) 4 mA to 20 mA (two-wire) intrinsically safe12
amplifiers 2c. 0 Vdc to 5 Vdc 2t. 0 Vdc to 10 Vdc output
2j. 4 mA to 20 mA (three-wire) output 2u. Unamplified, mV/V output
2k. 4 mA to 20 mA (two-wire)12
Internal amplifier 3a. Input/output isolation11
enhancements 3d. Remote buffered shunt calibration8
Electrical 6a. Bendix PTIH-10-6P (ranges to 2000 lb) 6g. Integral cable: Neoprene
termination 6b. MS connector MS3102E-14S-6P (mates 6h. Integral cable: Silicone
with MS3106E-14S-6S) (max. 160 °F) 6i. Integral underwater cable
(ranges 2000 lb and above)14 6j. 1/2-14 conduit fitting with 5 ft of 4 conductor PVC cable
6e. Integral cable: Teflon
6f. Integral cable: PVC
Shunt calibration 8a. Precision internal resistor13
Bridge resistance 12b. 5000 ohm (foil) (max. 250 °F)
Bridge type 31a. Dual bridge
Zero and span 14a. No access to pots
adjustment 14b. Top access to pots
Electrical 15a. Horizontal electrical exit port orientation
connector 15b. Vertical electrical exit port orientation
orientation 15c. Radial electrical exit port orientation
15d. Connector on end of cable
Special 30a. Compression only calibration, positive in compression
calibration 30b. Tension and compression calibration, positive in tension
Shock and 44a. Shock and vibration resistance
vibration
Interfaces 53e. Signature calibration13
53t. TEDS IEEE 1451.4 module7
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Precision Low Profile Load Cell
MOUNTING DIMENSIONS
Ranges D mm H mm F# ØG mm ØK mm T A mm A* mm B mm B* mm C mm
lb [in] [in] [in] B.C. [in] thru [in] [in] [in] [in] [in]
50 to 76,2 25,4 6 57,15 7,11 3/8-24 20,83 63,5 [2.5] 19,05 22,86 31,75
500 [3.00] [1.00] [2.250] [0.28] UNF [0.82] [0.75] [0.9] [1.25]
1000 to 88,9 25,4 6 66,68 8.64 1/2-20 20,83 63,5 [2.5] 19,05 22,86 31,75
2000 [3.50] [1.00] [2.625] [0.34] UNF [0.82] [0.75] [0.9] [1.25]
3000 to 139,7 45,72 8 114,3 10,16 1-14 UNS 31,75 58,42 38,1 38,1 [1.5] 50,8
7500 [5.50] [1.80] [4.500] [0.40] [1.25] [2.3] [1.50] [2.00]
10000 to 152,4 45,72 8 123,83 13,46 1 1/2-12 31,75 58,42 38,1 38,1 [1.5] 50,8
20000 [6.00] [1.80] [4.875] [0.53] UN [1.25] [2.3] [1.50] [2.00]
30000 to 190,5 50,8 8 152,4 19,81 2-12 UN 31,75 58,42 38,1 38,1 [1.5] 50,8
50000 [7.50] [2.00] [6.00] [0.78] [1.25] [2.3] [1.50] [2.00]
75000 to 228,6 63,5 12 196,85 16,76 2 1/2-12 31,75 58,42 38,1 38,1 [1.5] 50,8
100000 [9.0] [2.50] [7.75] [0.66] UN [1.25] [2.3] [1.50] [2.00]
150000, 355,6 107,95 12 298,45 26,16 3 1/2-8 31,75 58,42 38,1 38,1 **
200000 [14.00] [4.25] [11.750] [1.03] UN [1.25] [2.3] [1.50] [1.50]
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 75 Precision Low Profile Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. C dimension varies on high ranges. Consult factory.
2. Allowable maximum loads - maximum load to be applied without Honeywell’s standard product warranty applies unless agreed
damage.3 to otherwise by Honeywell in writing; please refer to your
3. Without damage - loading to this level will not cause excessive zero
shift or performance degradation. The user must consider fatigue life order acknowledgement or consult your local sales office for
for long term use and structural integrity. All structurally critical ap- specific warranty details. If warranted goods are returned to
plications (overhead loading, etc.) should always be designed with
safety redundant load paths. Honeywell during the period of coverage, Honeywell will repair
4. Interconnecting shunt cal. 1 terminal with shunt cal. 2 terminal or replace, at its option, without charge those items it finds
provides 50 % (unamplified units), 75 % (4 mA to 20 mA three-wire
defective. The foregoing is buyer’s sole remedy and is in lieu
units) or 80 % (voltage amplified units) of full scale output for quick
calibration. Shunt calibration comes standard with internal amplifier of all warranties, expressed or implied, including those of
option 2a, 2b, 2c, 2t and 2j. merchantability and fitness for a particular purpose. In no
5. O=Orange; Y=Yellow; B=Blue; Bl=Black; R=Red; Br=Brown;
W=White; G=Green. Color specifying cable and number or letter event shall Honeywell be liable for consequential, special, or
specifying connector. indirect damages.
6. No mating connector necessary for cable option.
7. Consult factory for TEDS availability with amplified models. While we provide application assistance personally, through our
8. Range dependent; consult factory. Termination dependent; consult
factory. literature and the Honeywell web site, it is up to the customer to
9. Internal amp and termination dependent; consult factory. determine the suitability of the product in the application.
10. This unit calibrated to Imperial (non-Metric) units.
11. Input/output isolation only available with voltage output (2b or 2c) Specifications may change without notice. The information we
amplifiers.
12. 5000 ohm bridge required. supply is believed to be accurate and reliable as of this printing.
13. Cannot be used with amplified option. However, we assume no responsibility for its use.
14. Cannot be used with options 1c, 1e, 1f, 1g, 1h, or 1i.
For more information about Sensing and Control products, visit
www.honeywell.com/sensing or call +1-815-235-6847
Email inquiries to info.sc@honeywell.com
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model UG
Ultra Precision Universal Canister Load Cell
DESCRIPTION
Model UG Ultra Precision Universal load cell achieves scale on both ends facilitate mounting in any position for tension,
quality and performance standards.The Model UG achieves compression, or universal force measurements. Model UG load
±0.03 % non-linearity with very little deflection (typically .0045 cells can be used in both static and dynamic applications.
in). It utilizes a four arm strain gage bridge which is bonded Stainless steel construction ensures high reliability.
and tested for high precision and dependability. Female threads
FEATURES
• 5 lb to 50000 lb
• 0.03 % non-linearity and hysteresis, respectively
• Stainless steel
• Mini footprint
• Button-style design
• mV/V output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model UG
Characteristic Measure
MOUNTING DIMENSIONS
Temperature, operating -34 °C to 85 °C [-30 °F to 185 °F]5
Rang- H mm ØD1 ØD2 ØD3 A mm T
Temperature, compensated 15 °C to 71 °C [60 °F to 160 °F]5
es lb [in] mm mm mm [in]
Temperature, storage -73 °C to 121 °C [-100 °F to 250 °F] [in] [in] [in]
Temperature effect, zero 0.0015 % full scale/°F 100 69,85 50,8 16,00 48,26 2,29 3/8-24 UNF
Temperature effect, span 0.0008 % full scale/°F [2.75] [2.00] [0.63] [1.9] [0.09] x 7/16 in
250, 69,85 50,8 16,00 48,26 4,57 3/8-24 UNF
500 [2.75] [2.00] [0.63] [1.9] [0.18] x 7/16 in
ELECTRICAL SPECIFICATIONS
1000, 104,90 63,5 19,05 50,8 4,57 1/2-20 UNF
Characteristic Measure 2000, [4.13] [2.50] [0.75] [2.00] [0.18] x 5/8 in
Strain gage type Bonded foil 3000,
4000
Excitation (calibration) 10 Vdc
5000, 149,35 88,9 39,62 76,2 4,83 1-14 UNF x
Insulation resistance 5000 mOhm @ 50 Vdc 7500, [5.88] [3.50] [1.56] [3.00] [0.19] 1 1/8 in
Bridge resistance 350 ohm 10000
Zero balance 1 % of full scale 15000, 215,9 127 60,45 109,22 16,00 1 1/2-12
Electrical termination (std) MS3102E-14S-6P 20000, [8.50] [5.00] [2.38] [4.3] [0.63] UNF x 2 in
30000
Mating connector (not MS3106A-14S-6S (AA121)
included) 50000, 304,8 152,4 92,20 139,7 17,53 2-12 UNF x
75000 [12.00] [6.00] [3.63] [5.5] [0.69] 2 1/2 in
100000, 401,32 190,5 121,92 172,72 17,53 3-8 UNF x 4
MECHANICAL SPECIFICATIONS 150000 [15.80] [7.5] [4.8] [6.8] [0.69] 1/2 in
Characteristic Measure
Maximum allowable load 150 % FS 2
Material Stainless steel
WIRING CODES
Connector Unamplified
A (+) excitation
B (+) excitation
C (-) excitation
D (-) excitation
E (-) output
F (+) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Ultra Precision Universal Canister Load Cell
INTERNAL AMPLIFIERS
Intrinsically
Amplifier Voltage output: Voltage output: Voltage output: Current three- Current two-
safe amp: Op-
specifications Option 2b Option 2c Option 2t wire: Option 2j wire: Option 2k
tion 2n (2N)***
Output signal ±5 V 0 V to 5 V or ±5 V 0 V to 10 V or ±10 4 mA to 20 mA 4 mA to 20 mA 4 mA to 20 mA
@ 45 mA V @ 45 mA
Input power ±15 V or 26 Vdc to 11 Vdc to 28 Vdc 15 Vdc to 28 Vdc 22 Vdc to 32 Vdc 15 Vdc to 9 Vdc to
(voltage) 32 Vdc 40 Vdc 28 Vdc
Input power 45 mA 40 mA 40 mA 65 mA 4 mA to 28 mA 4 mA to 24 mA
(current)
Freq. resp (amp) 3000 Hz 3000 Hz 3000 Hz 2500 Hz 300 Hz 2000 Hz
Power supply 60 db 60 db 60 db 60 db 60 db 60 db
rej.
Operating temp. -20 °F to 185 °F -20 °F to 185 °F -20 °F to 185 °F 0 °F to 185 °F 0 °F to 185 °F -20 °F to 185 °F
Reverse voltage Yes Yes Yes Yes Yes Yes
protection
Short cir. pro- Momentary Momentary Momentary Yes Yes Yes
tection
Wiring code: A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply
connector (std) B Output common B Output common** B Output common** B Output common** B No connection B No connection
C Supply return C Supply return ** C Supply return** C Supply return** C No connection C No connection
D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output
E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Case ground E Case ground
F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F No connection F No connection
Wiring code: R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
cable5,6,7 Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model UG
OPTION CODES
Many range/option combinations are available in
our quick-ship and fast-track manufacture pro-
grams. Please see http://sensing.honeywell.com/
TMsensor-ship for updated listings.
Load 100, 250, 500, 1000, 2000, 3000, 4000, 5000, 7500,
ranges 10000, 15000, 20000, 30000, 50000, 75000, 100000,
150000 lb
Tempera- 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F14
ture com- 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F14
pensation 1c. 0 °F to 185 °F 1i. -65 °F to 250 °F14
1d. -20 °F to 200 °F 1j. 0 °C to 50 °C
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
1f. 70 °F to 250 °F 1m. -25 °C to 110 °C
Internal 2b. ±5 Vdc 2n (2N) 4 mA to 20 mA
amplifiers 2c. 0 Vdc to 5 Vdc (wire) intrinsically safe13
output 2t. 0 Vdc to 10 Vdc
2j. 4 mA to 20 mA (three- 2u. Unamplified, mV/V
wire) out output
2k. 4 mA to 20 mA (two-
wire)13
Electrical 6a. Bendix PTIH-10-6P 6g. Integral cable: Neo-
termination (or equivalent) 6-pin prene
(max. 250 °F) 6i. Submersible cable15
6b. MS connector 6j. 1/2-14 conduit fitting
MS3102E-14S- with 5 ft of 4 conductor
6P (mates with PVC cable
MS3106E-14S-6S) 6q. Integral cable: Poly-
(max 160 °F)16 urethane
6e. Integral cable: Teflon
Shunt cali- 8a. Precision internal resistor14
bration
Bridge 12b. 5000 ohm (foil)
resistance 11a. Square bridge14
11b. Symmetrical bridge14
11c. Square and symmetrical bridge14
Special 30a. Compression only calibration, positive in com-
calibration pression
30b. Tension and compression calibration, positive in
tension
30c. Compression only calibration, negative in com-
pression
Shock and 44a. Shock and vibration resistance
vibration
Interfaces 53e. Signature calibration14
53t. TEDS IEEE 1451.4 module9
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model UG Ultra Precision Universal Canister Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. ±0.05% full scale less than or equal to 250 lb and greater than or
equal to 75000 lb. Honeywell’s standard product warranty applies unless agreed
2. Allowable maximum loads - maximum load to be applied without to otherwise by Honeywell in writing; please refer to your
damage.3
3. Without damage – loading to this level will not cause excessive order acknowledgement or consult your local sales office for
zero shift or performance degradation. The user must consider specific warranty details. If warranted goods are returned to
fatigue life for long term use and structural integrity. All structur-
Honeywell during the period of coverage, Honeywell will repair
ally critical applications (overhead loading, etc.) should always be
designed with safety redundant load paths. or replace, at its option, without charge those items it finds
4. Standard calibration for tension/ compression load cells is in ten- defective. The foregoing is buyer’s sole remedy and is in lieu
sion only.
5. Interconnecting shunt cal. 1 terminal with shunt cal. 2 terminal of all warranties, expressed or implied, including those of
provides 50 % (unamplified units), 75 % (4 mA to 20 mA three-wire merchantability and fitness for a particular purpose. In no
units) or 80 % (voltage amplified units) of full scale output for quick
calibration. Shunt calibration comes standard with internal amplifier event shall Honeywell be liable for consequential, special, or
option 2b, 2c, 2t and 2j. indirect damages.
6. O=Orange; Y=Yellow; B=Blue; Bl=Black; R=Red; Br=Brown;
W=White; G=Green. Color specifying cable and number or letter While we provide application assistance personally, through our
specifying connector.
7. No mating connector necessary for cable option. literature and the Honeywell web site, it is up to the customer to
8. Consult factory for extended temperature ranges. determine the suitability of the product in the application.
9. Consult factory for TEDS availability with amplified models.
10. Range dependent; consult factory. Termination dependent; consult Specifications may change without notice. The information we
factory.
11. Internal amp and termination dependent; consult factory. supply is believed to be accurate and reliable as of this printing.
12. This unit calibrated to Imperial (non-Metric) units. However, we assume no responsibility for its use.
13. 5000 ohm bridge required
14. Not available with amplified options. For more information about Sensing and Control products, visit
15. Temperature 82 °C [180 °F] max., non-shielded standard, shielded
available. www.honeywell.com/sensing or call +1-815-235-6847
16. Cannot be used with options 1c, 1e, 1f, 1g, 1h, or 1i. Email inquiries to info.sc@honeywell.com
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model AL-JP
High Output Load Cell
DESCRIPTION
Model AL-JP is a high output load cell (30 mV/V minimum). performance in non-linearity, hysteresis, and repeatability. Low
These semiconductor strain gage load cells are engineered to mechanical deflection allows for better response capability.
measure loads from 500 lb to 2000 lb. The tension/compression
Model AL-JP is designed with female threads. It provides high
FEATURES
• 500 lb, 1000 lb, and 2000 lb range
• Tension/compression
• High output/low bridge resistance (125 Ohm nominal)
• Drive meters without amplification
• Low mechanical deflection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model AL-JP
PERFORMANCE SPECIFICATIONS WIRING CODES
Characteristic Measure Tension
Load ranges4 500, 1000, 2000 lb A (+) excitation
Accuracy (static error B (+) signal
±0.15 % full scale
band)1 C (-) signal
Non-repeatability ±0.05 % full scale D (-) excitation
Output 30 mV/V minimum E shield
Operation Tension/compression
Resolution Infinite Compression
A (+) excitation
ENVIRONMENTAL SPECIFICATIONS B (-) signal
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model AL-SC
High Output Load Cell
DESCRIPTION
Model AL-SC is high-output load cell. These semiconductor linearity, hysteresis, and repeatability. Low mechanical deflection
strain gage load cells are engineered to measure loads from 500 allows for better response capability.
lb to 2000 lb. The tension/compression Model AL-SC is de-
signed with female threads. It provides high performance in non-
FEATURES
• 500 lb, 1000 lb, and 2000 lb range
• 0.15 % accuracy
• Tension/compression
• High output/low bridge resistance
• Low mechanical deflection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model AL-SC
Electrical termination (std) MS3100A-14S-5P at end of 1 ft cable Load range 500 lb, 1000 lb, 2000 lb
Temperature 10 °F to 120 °F
compensation
MECHANICAL SPECIFICATIONS Internal 2u. Unamplified, mV/V output
Characteristic Measure amplifiers
Maximum allowable load 200 % full scale 2 Electrical 3106B-14S-5P connector mounted at end of 10 ft
termination cable
Side load without damage 25 % full scale
Special 30a. Compression only (+) output
Weight See table
calibration 30b. Tension and compression (+,-) output
Material 17-4 PH stainless steel 30c. Compression only (-) output
Deflection See table
Natural frequency See table
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 31 Low
Low Range Precision Miniature Load Cell
DESCRIPTION
Model 31 low range precision miniature load cells measure term stability for ranges 1000 grams and above.) A modification
both tension and compression load forces of 50 grams to 500 permits this model to be completely welded for underwater
g. These models are our highest accuracy, rugged miniature applications. The Model 31 tension/compression load cell has
load cells. Model 31’s welded, stainless steel construction is male threads attachments. High accuracies of 0.15 % to 0.25 %
designed to eliminate or reduce to a minimum, the effects of full scale are achieved. Each bonded strain gage unit is built of
off-axis loads. (The internal construction assures excellent long- welded 17-4 PH stainless steel for additional ruggedness.
FEATURES
• 50 g to 500 g
• mV/V output
• Stainless steel
• Miniature design
• Double diaphragm construction
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 31 Low
WIRING CODES
Cable
Red (+) excitation
Black (-) excitation
Green (-) output
White (+) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 31 Low Low Range Precision Miniature Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads - maximum load to be applied without
damage. 2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life or long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. Standard calibration for tension/compression load cells is in tension
only. or replace, at its option, without charge those items it finds
4. TEDS available with integral cable units only. defective. The foregoing is buyer’s sole remedy and is in lieu
5. This unit calibrated to Imperial (non-Metric) units.
6. Signature calibration only available as inline module. of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
TYPICAL SYSTEM DIAGRAM event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 31 Mid
Mid Range Precision Miniature Load Cell
DESCRIPTION
Model 31 mid range precision miniature load cells measure both The Model 31 tension/compression load cell has male threads
tension and compression load forces of 1000 g to 1000 lb. These attachments. High accuracies of 0.15 % to 0.25 % full scale are
models are our highest accuracy, rugged miniature load cells. achieved. Each bonded strain gage unit is built of welded 17-4
Model 31’s welded, stainless steel construction is designed to PH stainless steel for additional ruggedness. All load cells with
eliminate or reduce to a minimum, the effects of off-axis loads. ranges from 1 kg to 10 lb have an electrical balance module in
(The internal construction assures excellent long-term stability the lead wire (approximately 1 in x .087 in thick). This balance
for ranges 1000 grams and above.) A modification permits this module does not have to be the same temperature as the
model to be completely welded for underwater applications. transducer.
FEATURES
• 1000 g to 1000 lb
• mV/V output
• Stainless steel
• Miniature design
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 31 Mid
Non-repeatability
±0.05 % full scale
CN 250 lb
5 lb to 1000 lb
CR 500 lb
Tolerance on output 1000 g 1.5 mV/V (nominal)
CV 1000 lb
Tolerance on output
2 mV/V
5 lb to 1000 lb
Operation Tension/compression 3 WIRING CODES
Resolution Infinite Cable Unamplified
Red (+) excitation
Temperature, operating -53 °C to 121 °C [-65 °F to 250 °F] White (+) output
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % FS1
Weight See table
Material 17-4 PH stainless steel
Deflection full scale See table
Natural frequency See table
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Mid Range Precision Miniature Load Cell
MOUNTING DIMENSIONS
Ranges (lb) T H C F A B
1000 g, 5 lb, 10 lb #6-32 UNC 11,43 mm 6,35 mm 1,27 mm 7,87 mm 4,83 mm
[0.45 in] [0.25 in] [0.05 in] [0.31 in] [0.19 in]
25 lb, 50 lb, 100 lb #10-32 UNF 13,21 mm 6,35 mm 0,76 mm 12,7 mm 6,35 mm
[0.52 in] [0.25 in] [0.03 in] [0.50 in] [0.25 in]
250 lb, 500 lb, 1000 lb 1/4-28 UNF 13,21 mm 9,65 mm 0,76 mm 12,7 mm 6,35 mm
[0.52 in] [0.38 in] [0.03 in] [0.50 in] [0.25 in]
OPTION CODES
Many range/option combinations are available
in our quick-ship and fast-track manufacture
programs. Please see http://sensing.honeywell.
com/TMsensor-ship for updated listings.
Load range 1000 g, 5 lb, 10 lb, 25 lb, 50 lb, 100 lb, 250 lb,
500 lb, 1000 lb
Temperature 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F
compensation 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F
1c. 0 °F to 185 °F 1i. -65 °F to 250 °F
1d. -20 °F to 130 °F 1j. 0 °C to 50 °C
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
1f. 70 °F to 250 °F 1m. -25 ° to 110 °C
Internal 2u. Unamplified, mV/V output
amplifiers
Overload 4a. Overload stops
stops
Electrical 6a. Bendix PTIH-10-6P 6h. Integral cable: Sili-
termination - 6 pin (max. 250 °F)5 cone
6d. Microtec DR-4S-4H 6i. Integral underwater
4 pin cable (max. 180 °F)
6e. Integral cable: 6v. Phoenix connector on
Teflon end of cable
6f. Integral cable: PVC 15d. Connector on end
of cable
Special 9a. 10 point (5 up/5 down) 20 % increments
calibration @ 20 °C
9b. 20 point (10 up/10 down) 10 % increments
@ 20 °C
Special 30a. Compression only calibration, positive in
calibration compression
30b. Tension and compression calibration, posi-
tive in tension
30c. Compression only calibration, negative in
compression
Shock and 44a. Shock and vibration resistance
vibration
Interfaces4 53e. Signature calibration7
53t. TEDS IEEE 1451.4 module
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 31 Mid Mid Range Precision Miniature Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads - maximum load to be applied without
damage. 2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. Standard calibration for tension/compression load cells is in tension
only. or replace, at its option, without charge those items it finds
4. TEDS available with integral cable units only. defective. The foregoing is buyer’s sole remedy and is in lieu
5. Availability varies with range.
6. This unit calibrated to Imperial (non-Metric) units. of all warranties, expressed or implied, including those of
7. Signature calibration only available as inline module. merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
TYPICAL SYSTEM DIAGRAM indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 31 High
High Range Precision Miniature Load Cell
DESCRIPTION
Model 31 high range precision miniature load cells measure term stability for ranges 1000 grams and above.) A modification
both tension and compression load forces of 2000 lb to 10000 permits this model to be completely welded for underwater
lb. These models are our highest accuracy, rugged miniature applications. The Model 31 tension/compression load cell has
load cells. Model 31’s welded, stainless steel construction is male threads attachments. High accuracies of 0.15 % to 0.25 %
designed to eliminate or reduce to a minimum, the effects of full scale are achieved. Each bonded strain gage unit is built of
off-axis loads. (The internal construction assures excellent long- welded 17-4 PH stainless steel for additional ruggedness.
FEATURES
• 2000 lb to 10000 lb
• mV/V output
• Stainless steel
• Miniature design
• Stabilized column construction
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 31 High
ELECTRICAL SPECIFICATIONS
Characteristic Measure
Strain gage type Bonded foil
Excitation (calibration) 5 Vdc
Insulation resistance 5000 Mohm @ 50 Vdc
Bridge resistance 350 ohm
Zero balance 1 % max.
Electrical termination (std) Teflon cable (1524 mm [60 in])
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % FS1
Weight See table
Material 17-4 PH stainless steel
Deflection full scale See table
Natural frequency See table
WIRING CODES
Cable Unamplified
Red (+) excitation
Black (-) excitation
Green (-) output
White (+) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
High Range Precision Miniature Load Cell
MOUNTING DIMENSIONS
Ranges (lb) T ØD C H
2000 lb, 3000 lb 3/8-24 UNF 25,4 mm [1.00 in] 12,7 mm [0.50 in] 18,29 mm [0.72 in]
4000 lb, 5000 lb 1/2-20 UNF 31,75 mm [1.25 in] 16 mm [0.63 in] 23,88 mm [0.94 in]
7500 lb, 10000 lb 3/4-16 UNF 35,05 mm [1.38 in] 22,35 mm [0.88 in] 27,94 mm [1.10 in]
OPTION CODES
Many range/option combinations are available
in our quick-ship and fast-track manufacture
programs. Please see http://sensing.honeywell.
com/TMsensor-ship for updated listings.
Load range 2000 lb, 3000 lb, 4000 lb, 5000 lb, 7500 lb,
10000 lb
Temperature 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F
compensation 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F
1c. 0 °F to 185 °F 1i. -65 °F to 250 °F
1d. -20 °F to 130 °F 1j. 0 °C to 50 °C
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
1f. 70 °F to 250 °F 1m. -25 ° to 110 °C
Internal 2u. Unamplified, mV/V output
amplifiers
Electrical 6e. Integral cable: 6h. Integral cable: Sili-
termination Teflon cone
6d. Microtec DR-4S-4H 6i. Integral underwater
4 pin cable (max. 180 °F)
6f. Integral cable: PVC 6v. Phoenix connector on
6g. Integral cable: end of cable
Neoprene (max.
180 °F)
Bridge 12a. 1000 ohm (foil)
resistance 12b. 5000 ohm (foil)
Electrical 15a. Horizontal electrical exit port orientation
connector 15b. Vertical electrical exit port orientation
orientation 15c. Radial electrical exit port orientation
15d. Connector on end of cable
Special 30a. Compression only calibration, positive in
calibration compression
30b. Tension and compression calibration, posi-
tive in tension
30c. Compression only calibration, negative in
compression
30d. Tension and compression calibration, posi-
tive in compression
Shock and 44a. Shock and vibration resistance
vibration
Interfaces 53e. Signature calibration6
53t. TEDS IEEE 1451.4 module4
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 31 High High Range Precision Miniature Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads - maximum load to be applied without
damage. 2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. Standard calibration for tension/compression load cells is in tension
only. or replace, at its option, without charge those items it finds
4. TEDS available with integral cable units only. defective. The foregoing is buyer’s sole remedy and is in lieu
5. This unit calibrated to Imperial (non-Metric) units.
6. Signature calibration only available as inline module. of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
TYPICAL SYSTEM DIAGRAM event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 34
Precision Miniature Load Cell
DESCRIPTION
Model 34 precision miniature load cells measure both tension The Model 34 tension/compression load cell has female threads
and compression load forces of 1000 g to 1000 lb. These attachments. High accuracies of 0.15 % to 0.25 % full scale are
models are our highest accuracy, rugged miniature load cells. achieved. Each bonded strain gage unit is built of welded 17-4
Model 34’s welded, stainless steel construction is designed to PH stainless steel for additional ruggedness. All load cells with
eliminate or reduce to a minimum, the effects of off-axis loads. ranges from 1 kg to 10 lb have an electrical balance module in
(The internal construction assures excellent long-term stability the lead wire (approximately 1 in x .087 in thick). This balance
for ranges 1000 grams and above.) A modification permits this module does not have to be the same temperature as the
model to be completely welded for underwater applications. transducer.
FEATURES
• 1000 g to 1000 lb
• Welded stainless steel
• Rugged, small size
• Tension/compression
• 0.15 %/0.20 % accuracy
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 34
Non-repeatability
±0.05 % full scale
CN 250 lb
5 lb to 1000 lb
CR 500 lb
Tolerance on output 1000 g 1.5 mV/V (nominal)
CV 1000 lb
Tolerance on output
2 mV/V
5 lb to 1000 lb
Operation Tension/compression3 WIRING CODES
Resolution Infinite Cable Unamplified
Red (+) excitation
Temperature, operating -53 °C to 121 °C [-65 °F to 250 °F] White (+) output
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % FS1
Weight See table
Material 17-4 PH stainless steel
Deflection full scale See table
Natural frequency See table
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Precision Miniature Load Cell
MOUNTING DIMENSIONS
Ranges D mm [in] H mm [in] A mm [in] B mm [in] C mm [in] F mm [in] G mm [in] T
1000 g, 5 lb, 10 lb 19,05 [0.75] 44,45 [1.75] 7,87 [0.31] 4,83 [0.19] 4,83 [0.46] 15,24 [0.60] 18,29 [0.72] 1/4-28 UNF
25 lb, 50 lb, 100 lb 25,4 [1.00] 44,45 [1.75] 12,7 [0.50] 6,35 [0.25] 4,83 [0.46] 13,21 [0.52] 18,29 [0.72] 1/4-28 UNF
250 lb, 500 lb, 1000 lb 25,4 [1.00] 50,8 [2.00] 12,7 [0.50] 6,35 [0.25] 4,83 [0.46] 19,05 [0.75] 19,05 [0.75] 1/4-28 UNF
OPTION CODES
Many range/option combinations are available
in our quick-ship and fast-track manufacture
programs. Please see http://sensing.honeywell.
com/TMsensor-ship for updated listings.
Load range 1000 g, 5 lb, 10 lb, 25 lb, 50 lb, 100 lb, 250 lb,
500 lb, 1000 lb
Temperature 1a. 60 °F to 160 °F 1k. -20 °C to 85 °C
compensation 1b. 30 °F to 130 °F 1m. -25 ° to 110 °C7
1c. 0 °F to 185 °F 1f. 70 °F to 250 °F
1d. -20 °F to 130 °F 1g. 70 °F to 325 °F7
1e. -20 °F to 200 °F 1h. 70 °F to 400 °F7
1j. 0 °C to 50 °C 1i. -65 °F to 250 °F7
Internal 2u. Unamplified, mV/V output
amplifiers
Overload 4a. Overload stops
stops
Electrical 6a. Bendix PTIH-10-6P 6h. Integral cable: Sili-
termination - 6 pin (max. 250 °F)5 cone
6d. Microtec DR-4S-4H 6i. Integral underwater
4 pin cable (max. 180 °F)
6e. Integral cable: 6v. Phoenix connector on
Teflon end of cable
6f. Integral cable: PVC 15d. Connector on end
6g. Integral cable: of cable
Neoprene (max. 180 °F)
Special 9a. 10 point (5 up/5 down) 20 % increments
calibration @ 20 °C
9b. 20 point (10 up/10 down) 10 % increments
@ 20 °C
Special 30a. Compression only calibration, positive in
calibration compression
30b. Tension and compression calibration, posi-
tive in tension
30c. Compression only calibration, negative in
compression
Shock and 44a. Shock and vibration resistance
vibration
Interfaces4 53e. Signature calibration7
53t. TEDS IEEE 1451.4 module
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 34 Precision Miniature Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads – maximum load to be applied without
Honeywell’s standard product warranty applies unless agreed
damage.2
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue order acknowledgement or consult your local sales office for
life for long term use and structural integrity. All structurally critical
specific warranty details. If warranted goods are returned to
applications (overhead loading, etc.) should always be designed
with safety redundant load paths. Honeywell during the period of coverage, Honeywell will repair
3. Standard calibration for tension/compression load cells is in tension or replace, at its option, without charge those items it finds
only. defective. The foregoing is buyer’s sole remedy and is in lieu
4. Option 53e and 53t are external in-line interfaces.
5. Availability varies with range. of all warranties, expressed or implied, including those of
6. This unit calibrated to Imperial (non-Metric) units. merchantability and fitness for a particular purpose. In no
7. Not available with 500 g range. event shall Honeywell be liable for consequential, special, or
indirect damages.
TYPICAL SYSTEM DIAGRAM
While we provide application assistance personally, through our
literature and the Honeywell web site, it is up to the customer to
determine the suitability of the product in the application.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 34 Semi Precision Miniature Load Cell
Order Code AL312
n 50 g to 500 g
n mV/V Output
n Stainless Steel
n Miniature Design
n Double Diaphragm Construction
1.75
1-888-282-9891 www.honeywell.com/sensotec
198
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 34 semi
Chart Recorder
Alarm Panel
Data Acquisition
Computer
PLC
Model 34 Semi
In-Line Amplifiers
(Used with unamplified units only)
Amplifier Output
Display Units Universal In-Line Amplifiers
UV +/- 5 VDC
SC500 UV-10 +/- 10 VDC
SC1000 UBP 0 +/- 5 VDC
SC2000 U3W 4-20 mA (3 wire)
SC2001 DIN rail Mount In-Line Amplifiers
SC3004 DV-05 0 +/- 5 VDC (3 wire)
GM DA-05 4-20 mA (3 wire)
NK DV-10 0 +/- 10 VDC (3 wire)
HH
Supplied as standard
Notes
1. Allowable Maximum Loads- Maximum load to be applied without damage (note 2).
2. Without Damage- loading to this level will not cause excessive zero shift or
performance degradation. The user must consider fatigue life for long term use and
structural integrity. All structurally critical applications (overhead loading, etc.)
should always be designed with safety redundant load paths.
How to Order
Combine the order code, the range code and the options code.
Sample Code: AL312 AJ 1b, 30a
Model Code Range Code Options Code
FEATURES
• 150 g to 1000 lb
• mV/V output
• Subminiature design
• Single diaphragm construction
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 11
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load See table1
Weight See table
Material Stainless steel
Deflection @ full scale See table
Natural frequency See table
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Subminiature Load Cell
OPTION CODES
Many range/option combinations are available in
our quick-ship and fast-track manufacture pro-
grams. Please see http://sensing.honeywell.com/
TMsensor-ship for updated listings.
Load 150 g, 250 g, 500 g, 1000 g, 5 lb, 10 lb, 25 lb, 50 lb,
range 100 lb, 250 lb, 500 lb, 1000 lb
Tempera- 1a. 60 °F to 160 °F
ture 1b. 30 °F to 130 °F
compen- 1c. 0 °F to 185 °F
sation 1e. -20 °F to 200 °F5
1f. 70 °F to 250 °F5
Internal 2u. Unamplified, mV/V output
amplifiers
Electrical 5 ft integral cable with balance board4
termina- 6a. Bendix PTIH-10-6P - (or equivalent) 6 pin (max.
tion 120 °C) on end of cable
6e. Integral cable: Teflon
6v. Phoenix connector on end of cable
Electrical 15d. Connector on end of cable
termina-
tion orien-
tation
Special 30a. Compression testing only, positive in compres-
calibration sion
30b. Tension and compression testing only, positive in
tension
30c. Compression testing only, negative in compres-
sion
Shock and 44a. Shock and vibration resistance
vibration
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 11 Subminiature Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads – maximum load to be applied without
damage.2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. Standard calibration for tension/compression load cells is tension
only. or replace, at its option, without charge those items it finds
4. A small, 2 in circuit board is included in the cable, 2 ft from the load defective. The foregoing is buyer’s sole remedy and is in lieu
cell. Do not remove this board.
5. Only for ranges greater-than-or-equal-to 1000 g. of all warranties, expressed or implied, including those of
6. Specifications may vary with this option. merchantability and fitness for a particular purpose. In no
7. This unit calibrated to Imperial (non-Metric) units.
event shall Honeywell be liable for consequential, special, or
indirect damages.
TYPICAL SYSTEM DIAGRAM
While we provide application assistance personally, through our
literature and the Honeywell web site, it is up to the customer to
determine the suitability of the product in the application.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 13
Subminiature Load Cell
DESCRIPTION
Model 13 (compression only) subminiature load cell is designed frequency response and low deflection to achieve a combined
to measure load ranges from 150 g to 1000 lb. With subminiature non-linearity and hysteresis of 0.25 % to 0.5 % full scale. A
dimensions, including diameters from 0.38 in to 0.75 in and balance module is included in the load cell’s lead wire cable for
heights of 0.13 in to 0.25 in, these units are easily incorporated temperature compensation and should not be removed.
into systems having limited space. Model 13 combines high
FEATURES
• 150 g to 1000 lb
• 0.7 % accuracy
• mV/V output
• Subminiature design
• Single diaphragm construction
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 13
PERFORMANCE SPECIFICATIONS RANGE CODES
Characteristic Measure Range codes Range
Load ranges6 150 g, 250 g, 500 g, 1000 g, 5 lb, AL 150 g
10 lb, 25 lb, 50 lb, 100 lb, 250 lb, 500 lb,
1000 lb AN 250 g
CV 1000 lb
ENVIRONMENTAL SPECIFICATIONS
Characteristic Measure WIRING CODES
Temperature, operating -54 °C to 121 °C [-65 °F to 250 °F] Cable Unamplified
Temperature, compensated 15 °C to 71 °C [60 °F to 160 °F] Red (+) excitation
Temperature effect, zero 0.01 % full scale/°F Black (-) excitation
Temperature effect, span 0.02 % reading/°F Green (-) output
White (+) output
ELECTRICAL SPECIFICATIONS
Characteristic Measure DEFLECTIONS AND RINGING FREQUENCIES
Strain gage type Semiconductor Capac- Deflec- Weight Weight with Max. al-
150 g to 500 g ity (lb) tion at cable lowable
Strain gage type Bonded foil
full scale load1 (%
1000 g to 1000 lb
(10-3 in) FS)
150 g 0.06 1 g [0.002 lb] 9 g [0.019 lb] 500
Excitation (calibration) 5 Vdc
250 g 0.06 1 g [0.002 lb] 9 g [0.019 lb] 500
Insulation resistance 5000 mOhm @ 50 Vdc
500 g 0.08 1 g [0.002 lb] 9 g [0.019 lb] 500
Bridge resistance (toler- 500 ohm (nominal)
ance)150 g to 500 g 1000 g 0.05 1 g [0.002 lb] 9 g [0.019 lb] 150
Bridge resistance (toler- 350 ohm (nominal) 5 lb 0.5 1 g [0.002 lb] 9 g [0.019 lb] 150
ance)1000 g to 1000 lb 10 lb 0.4 1 g [0.002 lb] 9 g [0.019 lb] 150
Zero balance (tolerance) ±3 % of full scale (nominal) 25 lb 0.4 1 g [0.002 lb] 9 g [0.019 lb] 150
Shunt calibration data Included 50 lb 0.4 1 g [0.002 lb] 9 g [0.019 lb] 150
Electrical termination (std) 1,83 m [5 ft] integral cable with balance 100 lb 0.4 3 g [0.006 lb] 11 g [0.024 lb] 150
board3
250 lb 0.5 3 g [0.006 lb] 11 g [0.024 lb] 150
MECHANICAL SPECIFICATIONS 500 lb 0.5 10 g [0.022 lb] 18 g [0.039 lb] 150
Characteristic Measure 1000 lb 0.6 10 g [0.022 lb] 18 g [0.039 lb] 150
Maximum allowable load See table
Weight See table
Material Stainless steel
Deflection @ full scale See table
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this datasheet is for
reference only. DO NOT USE this document as product
Find out more installation information.
Honeywell serves its customers • Complete installation, operation and maintenance
through a worldwide network of information is provided in the instructions supplied with
each product.
sales offices, representatives
Failure to comply with these instructions could result in
and distributors. For application
death or serious injury.
assistance, current specifica-
tions, pricing or name of the
nearest Authorized Distributor,
contact your local sales office.
To learn more about Honeywell’s
test and measurement products,
call +1-614-850-5000, visit
www.honeywell.com/sensotec,
or e-mail inquiries to
info.tm@honeywell.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model LFH-7I
Top Hat Subminiature Load Cell
DESCRIPTION
Model LFH-7I subminiature load cell is a low profile force accuracy of ±0.7 % full scale. The top of the load cell is the area
transducer for applications with minimal space and high where the force is applied and the base ring of the load cell
capacity requirements. This transducer utilizes foil strain gages must be placed on a hard, machine-ground flat surface to obtain
to measure compression loads of up to 10,000 lb and achieves optimum accuracy.
FEATURES
• 250 lb to 10000 lb range
• ±0.7 % accuracy
• Stainless steel
• Column construction
• mV/V output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model LFH-7I
WIRING CODES
Cable Unamplified
Red (+) excitation
Black (-) excitation
Green (-) output
White (+) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Top Hat Subminiature Load Cell
MOUNTING DIMENSIONS
Ranges ØD1 mm [in] ØD2 mm [in] H mm [in] F mm [in] W mm [in]
250 lb 12,7 [0.50] 6,86 [0.27] 9,65 [0.38] 3,3 [0.13] 10,92 [0.43]
500 lb 12,7 [0.50] 7,11 [0.28] 9,65 [0.38] 3,3 [0.13] 10,92 [0.43]
1000 lb 12,7 [0.50] 7,87 [0.31] 9,65 [0.38] 3,3 [0.13] 10,92 [0.43]
2000 lb 12,7 [0.50] 10,41 [0.41] 9,65 [0.38] 3,3 [0.13] 10,92 [0.43]
3000 lb 12,7 [0.50] 11,43 [0.45] 9,65 [0.38] 3,3 [0.13] 11,68 [0.46]
5000 lb 16,00 [0.63] 13,46 [0.53] 15,24 [0.60] 5,84 [0.23] 12,95 [0.51]
7500 lb 22,35 [0.88] 16,00 [0.63] 16,00 [0.63] 13,72 [0.54] 16,00 [0.63]
10000 lb 22,35 [0.88] 16,00 [0.63] 16,00 [0.63] 13,72 [0.54] 16,00 [0.63]
OPTION CODES
Many range/option combinations are available in
our quick-ship and fast-track manufacture pro-
grams. Please see http://sensing.honeywell.com/
TMsensor-ship for updated listings.
Load 250, 500, 1000, 2000, 3000, 4000, 5000, 7500, 10000
range lb
Tempera- 1a. 60 °F to 160 °F
ture 1b. 30 °F to 130 °F
compen- 1c. 0 °F to 185 °F
sation 1d. -20 °F to 130 °F
1e. -20 °F to 200 °F
1f. 70 °F to 250 °F
1j. 0 °C to 50 °C
1k. -20 °C to 85 °C
1m. -25 °C to 110 °C
Internal 2u. Unamplified, mV/V output
amplifiers
Electrical 6e. Integral cable: Teflon
termina- 6h. Integral cable: Silicone
tion 6v. Phoenix connector on end of cable
15d. Connector on end of cable
Special 9a. 10 point (5 up/5 down) 20 % increments @ 70 °F
calibration 9b. 20 point (10 up/10 down) 10 % increments @ 70 °F
Shock and 44a. Shock and vibration resistance
vibration
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model LFH-7I Top Hat Subminiature Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Accuracies stated are expected for best-fit straight line for all errors
including linearity, hysteresis and repeatability through zero. Honeywell’s standard product warranty applies unless agreed
2. Allowable maximum loads – maximum load to be applied without to otherwise by Honeywell in writing; please refer to your
damage.3
3. Without damage - loading to this level will not cause excessive zero order acknowledgement or consult your local sales office for
shift or performance degradation. The user must consider fatigue specific warranty details. If warranted goods are returned to
life for long term use and structural integrity. All structurally critical
Honeywell during the period of coverage, Honeywell will repair
applications (overhead loading, etc.) should always be designed
with safety redundant load paths. or replace, at its option, without charge those items it finds
4. This unit calibrated to Imperial (non-Metric) units. defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
TYPICAL SYSTEM DIAGRAM merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 45
Fatigue Rated Universal Load Cell
DESCRIPTION
Model 45 Ultra Precision Fatigue-Rated Load Cell offers a low Model 45 is available in ranges 250 lb through 100,000 lb. and
profile design for both tension and compression applications. mounting dimensions are universally interchangeable within the
The all-welded stainless steel construction and stabilizing test and measurement industry. Options include hi-level outputs
diaphragms provide the same ruggedness which has made our of 4 mA to 20 mA or 0 Vdc to 5 Vdc as well as weatherproof or
Model 41 and 43 pancake type load cells so successful. The submersible cable configurations.
FEATURES
• Up to 0.04 % accuracy (see specification table for specific
range)
• 250 lb to 100000 lb
• Long fatigue life
• Intrinsically safe available (2N option only)12
• CE approved13
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 45
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Fatigue Rated Universal Load Cell
INTERNAL AMPLIFIERS
Current two- Intrinsically
Amplifier Voltage out- Voltage out- Voltage out- Current three-
wire: Option safe amp: Op-
specifications put: Option 2b put: Option 2c put: Option 2t wire: Option 2j
2k tion 2n (2N)***
Output signal ±5 V 0 V to 5 V or ±5 V 0 V to 10 V or 4 mA to 20 mA 4 mA to 20 mA 4 mA to 20 mA
@ 45 mA ±10 V @ 45 mA
Input power (voltage) ±15 V or 26 Vdc 11 Vdc to 28 Vdc 15 Vdc to 28 Vdc 22 Vdc to 32 Vdc 15 Vdc to 9 Vdc to
to 32 Vdc 40 Vdc 28 Vdc
Input power (current) 45 mA 40 mA 40 mA 65 mA 4 mA to 28 mA 4 mA to 24 mA
Freq. resp (amp) 3000 Hz 3000 Hz 3000 Hz 2500 Hz 300 Hz 2000 Hz
Power supply rej. 60 db 60 db 60 db 60 db 60 db 60 db
Operating temp. -20 °F to 185 °F -20 °F to 185 °F -20 °F to 185 °F 0 °F to 185 °F 0 °F to 185 °F -20 °F to 185 °F
Reverse voltage protec- Yes Yes Yes Yes Yes Yes
tion
Short cir. protection Momentary Momentary Momentary Yes Yes Yes
Wiring code: connector A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply
(std)5 B Output common B Output common** B Output common** B Output common** B No connection B No connection
C Supply return C Supply return ** C Supply return** C Supply return** C No connection C No connection
D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output
E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Case ground E Case ground
F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F No connection F No connection
Wiring code: cable5,6,7 R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 45
OPTION CODES
Many range/option combinations are available
in our quick-ship and fast-track manufacture
programs. Please see http://sensing.honeywell.
com/TMsensor-ship for updated listings.
Load ranges 250, 500, 1000, 2500, 5000, 12500, 2500, 50000,
100000 lb
Temperature 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F16
compensation 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F16
1c. 0 °F to 185 °F 1i. -65 °F to 250 °F16
1d. -20 °F to 130 °F 1j. 0 °C to 50 °C
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
1f. 70 °F to 250 °F 1m. -25 °C to 110 °C
Internal ampli- 2b. ±5 Vdc output 2n (2N) 4 mA to 20 mA
fiers 2c. 0 Vdc to 5 Vdc (two-wire) intrinsically
2j. 4 mA to 20 mA safe15
(three-wire) output 2t. 0 Vdc to 10 Vdc
2k. 4 mA to 20 mA (two- output
wire)15 2u. Unamplified, mV/V
output
Internal 3d. Remote buffered shunt calibration
amplifier
enhancements
Electrical PC02A-10-6P
termination 6a. Bendix PTIH-10-6P (or equivalent), 6-pin (max.
250 °F)
6b. MS connector MS3102E-14S-6P (mates with
MS3106E-14S-6S) (max. 160 °F)17
Shunt 8a. Precision internal resistor16
calibration
Special 9c. ASTM E-74 calibration
calibration 30a. Compression only calibration, positive in
compression
30b. Tension and compression calibration, posi-
tive in tension
30c. Compression only calibration, negative in
compression
30d. Tension and compression calibration, posi-
tive in compression
Bridge type 31a. Dual bridge
11c. Square and symmetrical bridge16
Electrical 15a. Horizontal electrical exit port orientation
connector
orientation
Shock and 44a. Shock and vibration resistance
vibration
Interfaces 53e. Signature calibration16
53t. TEDS IEEE 1451.4 module11
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Fatigue Rated Universal Load Cell
MOUNTING DIMENSIONS
LOAD CELL Ø D1 mm [in] H mm [in] T ØB mm [in] N mm [in] F1
Ranges lb
250, 500, 1000, 104,65 [4.12] 34,8 [1.37] 5/8-18 UNF-3B 34,0 [1.34] 3,05 [0.12] 9/32 in dia.,
2500, 5000 8 holes eq. sp., 3.50 B.C.
12500, 25000 153,92 [6.06] 44,45 [1.75] 1 1/4-12 UNF-3B 67,31 [2.65] 3,05 [0.12] 13/32 in dia., 12 holes eq. sp., 5.125
B.C.
50000 203,2 [8.00] 63,5 [2.50] 1 3/4-12 UNF-3B 95,50 [3.76] 6,35 [0.25] 17/32 in dia.,
16 holes eq. sp., 6.50 B.C.
100000 279,4 [11.00] 88,9 [3.50] 2 3/4-8 UNF-3B 122,17 [4.81] 12,7 [0.50] 11/16 in dia.,
16 holes eq. sp., 9.00 B.C.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 45 Fatigue Rated Universal Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Static error band is the recommended performance specifica-
tion. The static error band is calculated as the best fit straight line Honeywell’s standard product warranty applies unless agreed
through zero, including the effects of non-linearity, hysteresis and to otherwise by Honeywell in writing; please refer to your
non-repeatability.
2. Values noted are typical values but fall within the static error. order acknowledgement or consult your local sales office for
3. Allowable maximum loads – maximum load to be applied without specific warranty details. If warranted goods are returned to
damage.4
4. Without damage - loading to this level will not cause excessive zero Honeywell during the period of coverage, Honeywell will repair
shift or performance degradation. The user must consider fatigue or replace, at its option, without charge those items it finds
life for long term use and structural integrity. All structurally critical
defective. The foregoing is buyer’s sole remedy and is in lieu
applications (overhead loading, etc.) should always be designed
with safety redundant load paths. of all warranties, expressed or implied, including those of
5. Interconnecting shunt cal. 1 terminal with shunt cal. 2 terminal merchantability and fitness for a particular purpose. In no
provides 50 % (unamplified units), 75 % (4 mA to 20 mA three-wire
units) or 80 % (voltage amplified units) of full scale output for quick event shall Honeywell be liable for consequential, special, or
calibration. Shunt calibration comes standard with internal amplifier indirect damages.
option 2c, 2t and 2j.
6. O=Orange; Y=Yellow; B=Blue; Bl=Black; R=Red; Br=Brown; While we provide application assistance personally, through our
W=White; G=Green. Color specifying cable and number or letter
specifying connector. literature and the Honeywell web site, it is up to the customer to
7. No mating connector necessary for cable option. determine the suitability of the product in the application.
8. 250 lb. range has 700 ohm bridge resistance.
9. Off axis loading maximum allowable 50 % full scale. Specifications may change without notice. The information we
10. Internal amplifier for ranges less than 12,500 lb may increase in
height. supply is believed to be accurate and reliable as of this printing.
11. Consult factory for TEDS availability with amplified models. However, we assume no responsibility for its use.
12. Range dependent; consult factory. Termination dependent; consult
factory. For more information about Sensing and Control products, visit
13. Internal amp and termination dependent; consult factory.
14. This unit calibrated to Imperial (non-Metric) units. www.honeywell.com/sensing or call +1-815-235-6847
15. 5000 ohm bridge required. Email inquiries to info.sc@honeywell.com
16. Cannot be used with amplified option.
17. Cannot be used with options 1c, 1e, 1f, 1g, 1h, or 1i.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 47
Fatigue Rated Ultra Precision
Universal Load Cell
DESCRIPTION
Model 47 Ultra Precision Fatigue Rated Load Cell offers a low Model 47 is available in ranges 250 lb through 100,000 lb. and
profile design for both tension and compression applications. mounting dimensions are universally interchangeable within the
The all welded stainless steel construction and stabilizing industry. Options include hi-level outputs of 4 mA to 20 mA or
diaphragms provide the same ruggedness which has made our 0 Vdc to 5 Vdc as well as weatherproof or submersible cable
Model 41 and 43 pancake type load cells so successful. The configurations.
FEATURES
• Accuracy up to 0.02 % (see specification table for specific
range)
• 250 lb to 100000 lb
• Long fatigue life
• Pull plate attached
• Intrinsically safe available (2N option only)12
• CE approved13
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 47
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 200 % FS 3, 9
Weight See table
Case material Stainless steel
Life cycles (approx.) > 108 cycles fully reversed
Deflection See table
Natural frequency See table
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Fatigue Rated Ultra Precision Universal Load Cell
INTERNAL AMPLIFIERS
Current two- Intrinsically
Amplifier Voltage out- Voltage out- Voltage out- Current three-
wire: Option safe amp: Op-
specifications put: Option 2b put: Option 2c put: Option 2t wire: Option 2j
2k tion 2n (2N)***
Output signal ±5 V 0 V to 5 V or ±5 V 0 V to 10 V or 4 mA to 20 mA 4 mA to 20 mA 4 mA to 20 mA
@ 45 mA ±10 V @ 45 mA
Input power (voltage) ±15 V or 26 Vdc 11 Vdc to 28 Vdc 15 Vdc to 28 Vdc 22 Vdc to 32 Vdc 15 Vdc to 9 Vdc to
to 32 Vdc 40 Vdc 28 Vdc
Input power (current) 45 mA 40 mA 40 mA 65 mA 4 mA to 28 mA 4 mA to 24 mA
Freq. resp (amp) 3000 Hz 3000 Hz 3000 Hz 2500 Hz 300 Hz 2000 Hz
Power supply rej. 60 db 60 db 60 db 60 db 60 db 60 db
Operating temp. -20 °F to 185 °F -20 °F to 185 °F -20 °F to 185 °F 0 °F to 185 °F 0 °F to 185 °F -20 °F to 185 °F
Reverse voltage protec- Yes Yes Yes Yes Yes Yes
tion
Short cir. protection Momentary Momentary Momentary Yes Yes Yes
Wiring code: connector A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply
(std)5 B Output common B Output common** B Output common** B Output common** B No connection B No connection
C Supply return C Supply return ** C Supply return** C Supply return** C No connection C No connection
D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output
E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Case ground E Case ground
F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F No connection F No connection
Wiring code: cable5,6,7 R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 47
OPTION CODES
Many range/option combinations are available
in our quick-ship and fast-track manufacture
programs. Please see http://sensing.honey-
well.com/TMsensor-ship for updated listings.
Load ranges 250, 500, 1000, 2500, 5000, 12500, 2500, 50000,
100000 lb
Temperature 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F16
compensation 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F16
1c. 0 °F to 185 °F 1i. -65 °F to 250 °F16
1d. -20 °F to 130 °F 1j. 0 °C to 50 °C
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
1f. 70 °F to 250 °F 1m. -25 °C to 110 °C
Internal ampli- 2b. ±5 Vdc output 2n (2N) 4 mA to 20 mA
fiers 2c. 0 Vdc to 5 Vdc (two-wire) intrinsi-
2j. 4 mA to 20 mA cally safe15
(three-wire) output 2t. 0 Vdc to 10 Vdc
2k. 4 mA to 20 mA (two- output
wire)15 2u. Unamplified, mV/V
output
Electrical 6a. Bendix PTIH-10-6P 6h. Integral cable:
termination (or equivalent) 6-pin Silicone
(max. 250 °F) 6i. Integral underwater
6b. MS connector cable
MS3102E-14S- 6j. 1/2-14 conduit
6P (mates with fitting with 5 ft of
MS3106-14S 6P) 4 conductor PVC
(max. 160 °F)17 cable
6e. Integral cable: 6q. Molded integral ca-
Teflon ble: Polyurethane
6f. Integral cable: PVC 6v. Phoenix connector
6g. Integral cable: on end of cable
Neoprene6 15d. Connector on end
of cable
Shunt 8a. Precision internal resistor16
calibration
Special 9a. 10 point (5 up/5 down) 20 % increments @ 70
calibration °F
9b. 20 point (10 up/10 down) 10 % increments @
70 °F
9c. ASTM E-74 calibration
9e. CE mark
30a. Compression only calibration, positive in com-
pression
30b. Tension and compression calibration, positive
in tension
30c. Compression only calibration, negative in
compression
30d. Tension and compression calibration, positive in
compression
Bridge type 31a. Dual bridge
11a. Square bridge16
11c. Square and symmetrical bridge16
Bridge 12b. 5000 ohm (foil) (max 250 °F)
resistance
Electrical 15a. Horizontal electrical exit port orientation
connector 15b. Vertical electrical exit port orientation
orientation 15c. Radial electrical exit port orientation
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Fatigue Rated Ultra Precision Universal Load Cell
MOUNTING DIMENSIONS
LOAD CELL Ø D1 mm [in] H mm [in] T ØB mm [in] N mm [in] ØG mm [in]
Ranges lb
250, 500, 1000, 104,65 [4.12] 34,8 [1.37] 5/8-18 UNF-3B 34,0 [1.34] 3,05 [0.12] 31,75 [1.25]
2500, 5000
12500, 25000 153,92 [6.06] 44,45 [1.75] 1 1/4-12 UNF-3B 67,31 [2.65] 3,05 [0.12] 57,15 [2.25]
50000 203,2 [8.00] 63,5 [2.50] 1 3/4-12 UNF-3B 95,50 [3.76] 6,35 [0.25] 76,2 [3.00]
100000 279,4 [11.00] 88,9 [3.50] 2 3/4-8 UNF-3B 122,17 [4.81] 12,7 [0.50] 114,3 [4.50]
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 47 Fatigue Rated Ultra Precision Universal Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Static error band is the recommended performance specifica-
tion. The static error band is calculated as the best fit straight line Honeywell’s standard product warranty applies unless agreed
through zero, including the effects of non-linearity, hysteresis and to otherwise by Honeywell in writing; please refer to your
non-repeatability.
2. Values noted are typical values but fall within the static error. order acknowledgement or consult your local sales office for
3. Allowable maximum loads – maximum load to be applied without specific warranty details. If warranted goods are returned to
damage.4
4. Without damage - loading to this level will not cause excessive zero Honeywell during the period of coverage, Honeywell will repair
shift or performance degradation. The user must consider fatigue or replace, at its option, without charge those items it finds
life for long term use and structural integrity. All structurally critical
defective. The foregoing is buyer’s sole remedy and is in lieu
applications (overhead loading, etc.) should always be designed
with safety redundant load paths. of all warranties, expressed or implied, including those of
5. Interconnecting shunt cal. 1 terminal with shunt cal. 2 terminal merchantability and fitness for a particular purpose. In no
provides 50 % (unamplified units), 75 % (4 mA to 20 mA three-wire
units) or 80 % (voltage amplified units) of full scale output for quick event shall Honeywell be liable for consequential, special, or
calibration. Shunt calibration comes standard with internal amplifier indirect damages.
option 2c, 2t and 2j.
6. O=Orange; Y=Yellow; B=Blue; Bl=Black; R=Red; Br=Brown; While we provide application assistance personally, through our
W=White; G=Green. Color specifying cable and number or letter
specifying connector. literature and the Honeywell web site, it is up to the customer to
7. No mating connector necessary for cable option. determine the suitability of the product in the application.
8. 250 lb range has 700 ohm bridge resistance.
9. Off axis loading maximum allowable 50% full scale. Specifications may change without notice. The information we
10. Internal amplifier for ranges less than 12500 lb may increase in
height. supply is believed to be accurate and reliable as of this printing.
11. Consult factory for TEDS availability with amplified models. However, we assume no responsibility for its use.
12. Range dependent; consult factory. Termination dependent; consult
factory. For more information about Sensing and Control products, visit
13. Internal amp and termination dependent; consult factory.
14. This unit calibrated to Imperial (non-Metric) units. www.honeywell.com/sensing or call +1-815-235-6847
15. 5000 ohm bridge required. Email inquiries to info.sc@honeywell.com
16. Cannot be used with amplified option.
17. Cannot be used with options 1c, 1e, 1f, 1g, 1h, or 1i.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 73
Precision Fatigue-Rated Low Profile
Load Cell
DESCRIPTION
Model 73 fatigue-rated load cells are engineered for applications scale). Model 73 measures compression only. It must be used
such as materials or product fatigue testing, which involve an on a smooth flat surface to achieve rated specifications. The
extremely large number of cycles or occasional overload condi- load button on Model 73 is an integral part of the load cell and
tions. These fatigue rated load cells have load ranges from 50 cannot be removed or changed. Model 73 utilizes two stabilizing
lbs to 200,000 lbs and achieve a non-linearity of 0.1% full scale. diaphragms, which are welded to the sensing member to reduce
The superior design of these bonded foil, strain gage compres- off-center and side-loading effects.
sion load cells permits a fatigue life of 1 billion cycles (zero to full
FEATURES
• 0.10 % accuracy
• 50 lb to 200000 lb
• mV/V output (standard); 4 mA to 20 mA or 0 Vdc to 5 Vdc
(optional) output
• Stainless steel
• Double diaphragm design
• Enhanced overload capacity
• Intrinsically safe available (2N option only)7
• CE approved8
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 73
WIRING CODES
Connector Unamplified (Std.)
A (+) excitation
B (+) excitation
C (-) excitation
D (-) excitation
E (-) output
F (+) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Precision Fatigue-Rated Low Profile Load Cell
INTERNAL AMPLIFIERS
Current two- Intrinsically
Amplifier Voltage out- Voltage out- Voltage out- Current three-
wire: Option safe amp: Op-
specifications put: Option 2a put: Option 2c put: Option 2t wire: Option 2j
2k tion 2n (2N)***
Output signal 0 V to 5 V 0 V to 5 V or ±5 V 0 V to 10 V or 4 mA to 20 mA 4 mA to 20 mA 4 mA to 20 mA
@ 45 mA ±10 V @ 45 mA
Input power (voltage) ±15 V or 26 Vdc 11 Vdc to 28 Vdc 15 Vdc to 28 Vdc 22 Vdc to 32 Vdc 15 Vdc to 9 Vdc to
to 32 Vdc 40 Vdc 28 Vdc
Input power (current) 45 mA 40 mA 40 mA 65 mA 4 mA to 28 mA 4 mA to 24 mA
Freq. resp (amp) 3000 Hz 3000 Hz 3000 Hz 2500 Hz 300 Hz 2000 Hz
Power supply rej. 60 db 60 db 60 db 60 db 60 db 60 db
Operating temp. -20 °F to 185 °F -20 °F to 185 °F -20 °F to 185 °F 0 °F to 185 °F 0 °F to 185 °F -20 °F to 185 °F
Reverse voltage protec- Yes Yes Yes Yes Yes Yes
tion
Short cir. protection Momentary Momentary Momentary Yes Yes Yes
Wiring code: connector A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply
(std)4 B Output common B Output common** B Output common** B Output common** B No connection B No connection
C Supply return C Supply return ** C Supply return** C Supply return** C No connection C No connection
D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output
E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Case ground E Case ground
F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F No connection F No connection
Wiring code: cable4,5,6 R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
* Black and green wires are internally connected.
** Pins B and C are internally connected.
*** See our Web site for the most up-to-date information regarding intrinsically safe approvals, ref. #008-0547-00.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 73
OPTION CODES
Many range/option combinations are available in our quick-ship and fast-track manufacture programs. Please
see http://sensing.honeywell.com/TMsensor-ship for updated listings.
Load ranges 50, 100, 250, 500, 1000, 2000, 3000, 4000, 5000, 7500, 10000, 15000, 20000, 30000, 50000, 75000, 100000, 150000, 200000 lb
Temperature 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F12
compensa- 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F12
tion 1c. 0 °F to 185 °F 1i. -65 °F to 250 °F12
1d. -20 °F to 130 °F 1j. 0 °F to 50 °C
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
1f. 70 °F to 250 °F 1m. -25 °C to 110 °C
Internal 2b. Four-wire, 0 Vdc to 5 Vdc output 2n (2N) 4 mA to 20 mA (two-wire) intrinsically safe11
amplifiers 2c. 0 Vdc to 5 Vdc 2t. 0 Vdc to 10 Vdc output
2j. 4 mA to 20 mA (three-wire) output 2u. Unamplified, mV/V output
2k. 4 mA to 20 mA (two-wire)11
Internal 3a. Input/output isolation10
amplifier en- 3d. Remote buffered shunt calibration8
hancements
Electrical 6a. Bendix PTIH-10-6P (or equivalent), 6-pin (max. 250 °F) 6f. Integral cable: PVC
termination 6b. MS connector MS3102E-14S-6P (mates with MS3106E-14S- 6g. Integral cable: Neoprene
6S) (max. 160 °F) (ranges 2000 and above)13 6h. Integral cable: Silicone
6e. Integral cable: Teflon 6i. Integral underwater cable
6j. 1/2-14 conduit fitting with 5 ft of 4 conductor PVC cable
Shunt 8a. Precision internal resistor12
calibration
Bridge 12b. 5000 ohm (foil) (max. 250 °F)
resistance
Bridge type 31a. Dual bridge
Zero and 14a. No access to pots
span adjust- 14b. Top access to pots
ment
Electrical 15a. Horizontal electrical exit port orientation
connector 15b. Vertical electrical exit port orientation
orientation 15c. Radial electrical exit port orientation
15d. Connector on end of cable
Special 30a. Compression only, positive output
calibration 9a. 10 point (5 up/5 down) 20 % increments @ 70 °F
9b. 20 point (10 up/10 down) 10 % increments @ 70 °F
9c. ASTM E-74 calibration
Shock and 44a. Shock and vibration resistance
vibration
Interfaces 53e. Signature calibration12
53t. TEDS IEEE 1451.4 module6
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Precision Fatigue-Rated Low Profile Load Cell
MOUNTING DIMENSIONS
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 73 Precision Fatigue-Rate Low Profile Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads - maximum load to be applied without
damage.2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
3. Interconnecting shunt cal. 1 terminal with shunt cal. 2 terminal Honeywell during the period of coverage, Honeywell will repair
provides 50 % (unamplified units), 75 % (4 mA to 20 mA three-wire or replace, at its option, without charge those items it finds
units) or 80 % (voltage amplified units) of full scale output for quick
defective. The foregoing is buyer’s sole remedy and is in lieu
calibration. Shunt calibration comes standard with internal amplifier
option 2a, 2b, 2c, 2t and 2j. of all warranties, expressed or implied, including those of
4. O=Orange; Y=Yellow; B=Blue; Bl=Black; R=Red; Br=Brown; merchantability and fitness for a particular purpose. In no
W=White; G=Green. Color specifying cable and number or letter
specifying connector. event shall Honeywell be liable for consequential, special, or
5. No mating connector necessary for cable option. indirect damages.
6. Consult factory for TEDS availability with amplified models.
7. Range dependent; consult factory. Termination dependent; consult While we provide application assistance personally, through our
factory.
8. Internal amp and termination dependent; consult factory. literature and the Honeywell web site, it is up to the customer to
9. This unit calibrated to Imperial (non-Metric) units. determine the suitability of the product in the application.
10. Input/output isolation only available with voltage output (2b or 2c)
amplifier. Specifications may change without notice. The information we
11. 5000 ohm bridge required.
12. Cannot be used with amplified option. supply is believed to be accurate and reliable as of this printing.
13. Cannot be used with options 1c, 1e, 1f, 1g, 1g, or 1i. However, we assume no responsibility for its use.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Models 3149-FR
Low Capacity Fatigue Load Cell
DESCRIPTION
The 3149-FR tension/compression load cells are designed for The sensors have a nominal bridge resistance of 350 ohm and
demanding applications in automotive, aerospace and military can be powered by up to 15 Vac or Vdc. Safe overload range is
markets. 150% of rated capacity.
This model is offered in capacity ratings of 50, 100 and 300 lb. The load cells are offered with optional dual bridge output to
Standard output is 2.0 mV/V with an overall accuracy of 0.05%. provide force feedback and control or redundancy.
FEATURES
• Fatigue rated
• Compact size
• High accuracy
• Tension and compression
• Dual bridge output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3179-FR
A
Hysteresis ±0.05 % of rated output 2.36
Non-repeatability ±0.01 % of rated output
Static error band ±0.05 % of rated output
Ø2.75
Creep ±0.03 % (reading in 20 minutes)
MECHANICAL SPECIFICATIONS
Display Units
Characteristic Measure
SC500 SC1000 SC2000
Safe overload range 150 % of rated output
SC2001 SC3004
Weight 0.8 lb GM NK HH
7541 7558 7561-PSD
Flexure material Aluminum MODEL 3149FR
WIRING CODES OR
2003.1 lb.
L1 L2 L3 L4
VALUE CLEAR CHAN TARE
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3179-FR Low Capacity Fatigue Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3108
Tension/Compression Pancake Load Cell
DESCRIPTION
These general purpose designs have exceptional structural Available in capacities of five and ten pounds, they offer
capability to withstand extraneous loads, such as torque, maximum performance and enhanced accuracy.
bending moments, and side loads. This low-range cell has built- Minimum deflection and compactness make these general-
in temperature compensation. purpose load cells easy to install and use.
FEATURES
• 5 lb to 10 lb range
• 0.05 % accuracy
• Low sensitivity to extraneous loads
• Low deflection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3108
Honeywell
ENVIRONMENTAL SPECIFICATIONS In-Line Amplifier
Output Input
Serial Number
Characteristic Measure
Temperature, operating -54 °C to 93 °C [-65 °F to 200 °F] Display Units
Temperature, compensated 21 °C to 77 °C [70 °F to 170 °F] SC500 SC1000 SC2000
Temperature effect, zero ±0.002 % of rated output/°F SC2001 SC3004
GM NK HH
Temperature effect, output ±0.002 % of reading/°F 7541 7558 7561-PSD
MODEL 3108
ELECTRICAL SPECIFICATIONS
2003.1 lb.
OR
Characteristic Measure VALUE
L1 L2 L3 L4
CLEAR CHAN TARE
WIRING CODES
Cable
Red (+) excitation
Black (-) excitation
Green (+) output
White (-) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Tension/Compression Pancake Load Cell
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static over- Shear FX or Bending MX Torque MZ Deflection at Ringing fre-
load capacity FY (lb) or MY (lb-in) (lb-in) nominal load quency (Hz)
(% of nominal limit (in)
capacity)
5 20 150 30 30 3 0.005 500
10 50 150 40 40 4 0.005 900
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in]
3108 6,98 [2.75] 0,55 [0.22] 0,32 [0.13] 4,44 [1.75] 5,60 [2.22] - [1/4-28]
A SPANNER WRENCH
HOLE B DIA.
F THD. C DEEP
G DEEP
BOTH ENDS
RECEP.
PTO2E-10-6P
E
DUAL BRIDGE
OPTIONAL
H DIA.
J
C
P
K
L
N DIA.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3108 Tension/Compression Pancake Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3132
Tension/Compression Pancake Load Cell
DESCRIPTION
These general purpose designs have exceptional structural Minimum deflection and compactness make these general-
capability to withstand extraneous loads, such as torque, purpose load cells easy to install and use.
bending moments, and side loads.
FEATURES
• 500 lb to 5000 lb range
• Low sensitivity to extraneous loads
• Low deflection
• Rugged welded construction
• Built-in temperature compensation
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3132
Honeywell
ENVIRONMENTAL SPECIFICATIONS In-Line Amplifier
Output Input
Characteristic Measure
Serial Number
WIRING CODES
Cable
Red (+) excitation
Black (-) excitation
Green (+) output
White (-) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Tension/Compression Pancake Load Cell
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static over- Shear FX or Bending MX Torque MZ Deflection at Ringing fre-
load capacity FY (lb) or MY (lb-in) (lb-in) nominal load quency (Hz)
(% of nominal limit (in)
capacity)
500 2K 150 1400 2800 1100 0.005 1600
1K 5K 150 2000 3900 1100 0.005 2000
2K 10K 150 2800 5000 1100 0.005 3200
3K 15K 150 3400 5500 1100 0.005 4100
5K 20K 150 4200 5500 1100 0.005 5000
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in]
3132 6,65 [2.62] 1,60 [0.63] 8,89 [3.50] 2,54 [1.0] 3,02 [1.19] 4,45 [1.75]
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3132 Tension/Compression Pancake Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Models 3140-CS
Tension/Compression Pancake Load Cell
DESCRIPTION
The Model 3140-CS load cell series has been designed as compression load cells can be used when accuracy is a high
a reference standard for calibration labs in automotive, priority requirement. Some advantages of these load cells are:
aerospace, military or industrial markets. These tension/ compact size, high accuracy and availability.
FEATURES
• Enhanced accuracy, up to 0.02 %
• 300 lb to 100000 lb range
• Universal tension and compression loading
• Low profile
• 150 % full scale safe overload capability
• Available in single or optional dual bridge configuration
• Metric sizes available
• Factory installed calibration adapters
• Eccentric load compensated
• High precision base installed
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3140-CS
Characteristic Measure
Strain gage type Foil 2003.1 lb.
OR L1 L2 L3 L4
Excitation (maximum) 10 Vdc or Vac RMS VALUE CLEAR CHAN TARE
UP DOWN SETUP ENTER EXIT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Tension/Compression Pancake Load Cell
Honeywell Honeywell
In-Line Amplifier
In-Line Amplifier
Output Input
Serial Number Output Input
Serial Number
2003.1 lb.
OR L1 L2 L3 L4 2003.1 lb.
VALUE CLEAR
OR L1 L2 L3 L4
CHAN TARE
UP DOWN SETUP ENTER EXIT VALUE CLEAR CHAN TARE
UP DOWN SETUP ENTER EXIT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3140-CS
MOUNTING DIMENSIONS
Model Capacity ØA B in C in D in E in F in G in Ø H in J Thread Ø K in L Thread M in.
(lb) in
3143-CS-300 300 4.12 0.13 1.25 2.50 3.44 4.18 0.03 1.25 1/2-20 UNF 3A 6.00 1/2-20 UNF 3B 0.88
3143-CS-500 500 4.12 0.13 1.25 2.50 3.44 4.18 0.03 1.25 1/2-20 UNF 3A 6.00 1/2-20 UNF 3B 0.88
3143-CS-1K 1000 4.12 0.13 1.25 2.50 3.44 4.18 0.03 1.25 1/2-20 UNF 3A 6.00 1/2-20 UNF 3B 0.88
3143-CS-2K 2000 4.12 0.13 1.25 2.50 3.44 4.18 0.03 1.25 1/2-20 UNF 3A 6.00 1/2-20 UNF 3B 0.88
3144-CS-5K 5000 4.12 0.13 1.25 2.50 3.44 4.19 0.03 1.25 5/8-18 UNF 3A 6.00 5/8-18 UNF 3B 0.88
3144-CS-10K 10000 4.12 0.13 1.25 2.50 3.44 4.19 0.03 1.25 5/8-18 UNF 3A 6.00 5/8-18 UNF 3B 0.88
3145-CS-25K 25000 6.06 0.13 1.63 3.50 4.94 6.44 0.03 1.25 1¼-12 UNF 3A 6.00 1¼-12 UNF 3B 1.50
3145-CS-50K 50000 6.06 0.13 1.63 3.50 4.94 6.44 0.03 2.25 1¼-12 UNF 3A 6.00 1¼-12 UNF 3B 1.50
3146-CS-100K 100000 8.00 0.25 2.25 4.50 6.13 7.88 0.03 3.00 1¾-12 UNF 3A 12.00 1¾-12 UNF 3B 1.75
RECEP. F
PT02E-10-6P
E
ØK R
ØH
ØA
B L THD.
J THD. C M DEEP
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3140-CS Tension/Compression Pancake Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
TYPICAL SYSTEM DIAGRAM order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
In-Line Amplifiers Customer Supplied
(Used with unamplified units only) Honeywell during the period of coverage, Honeywell will repair
Chart Recorder
Alarm Panel or replace, at its option, without charge those items it finds
Amplifier Output
Universal In-Line Amplifiers Data Acquisition defective. The foregoing is buyer’s sole remedy and is in lieu
UV +/-5 VDC Computer
PLC of all warranties, expressed or implied, including those of
UV-10 +/-10 VDC
UBP 0 +/-5 VDC merchantability and fitness for a particular purpose. In no
U3W 4-20mA (3 wire)
U2W 4-20mA (2 wire) event shall Honeywell be liable for consequential, special, or
DIN rail Mount In-Line Amplifiers indirect damages.
DV-05 0 +/- 5 VDC (3 wire) Power Supply
DA-05 4-20mA (3 wire)
DV10 0 +/- 10 VDC (3 wire)
While we provide application assistance personally, through our
literature and the Honeywell web site, it is up to the customer to
Honeywell determine the suitability of the product in the application.
In-Line Amplifier
Output Input
OR
2003.1 lb.
L1 L2 L3 L4
WARNING
VALUE
UP
CLEAR
DOWN SETUP
CHAN
ENTER
TARE
EXIT PERSONAL INJURY
• DO NOT USE these products as safety or emergency
Mating Connectors & Cables stop devices or in any other application where failure of
the product could result in personal injury.
023-LW181-023-LF Mating Connector
7205-76-XX* Mating connector & 6 conductor cable Failure to comply with these instructions could result in
(unamplified unit with sense leads but not shunt cal) death or serious injury.
7205-75-XX** Mating connector & 4 conductor cable
(unamplified unit without sense leads but not shunt cal)
7205-83-XX* Mating connector & 6 conductor cable
(for connection to instrument 7541) WARNING
7205-82-XX** Mating connector & 4 conductor cable MISUSE OF DOCUMENTATION
(for connection to instrument 7541)
• The information presented in this catalogue is for
* XX represents length in feet 100ft maximum
** XX represents length in feet 20ft maximum reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Models 3140-P
Tension/Compression Pancake Load Cell
DESCRIPTION
Designed for general purpose use in demanding applications in
automotive, aerospace, and military applications. Some advan-
tages of these tension/compression load cells include compact
size, high accuracy, and cost efficiency. The 3140-P has smaller
maximum off-center load and moment error than the standard
3140 Series.
FEATURES
• Static error band 0.02 % to 0.04 %
• English threads
• Enhanced accuracy version of standard 3140 Series
• Low profile
• Low sensitivity to magnetic fields
• Output to 4 mV/V
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3140-P
Characteristic Measure
Display Units
Temperature, operating -54 °C to 93 °C [-65 °F to 200 °F]
Temperature, compensated -9 °C to 46 °C [15 °F to 115 °F] SC500 SC1000 SC2000
SC2001 SC3004
Temperature effect, zero ±0.008 % of rated output/°F GM NK HH
Temperature effect, output ±0.008 % of reading/°F MODEL 3143P 7541 7558 7561-PSD
ELECTRICAL SPECIFICATIONS OR
2003.1 lb.
Characteristic Measure VALUE
L1 L2 L3 L4
CLEAR CHAN TARE
Input resistance (tolerance) 350 ohm +40/-3.5 ohm 023-LW181-023-LF Mating Connector
7205-76-XX* Mating connector & 6 conductor cable
Output resistance 350 ohm ±3.5 ohm (unamplified unit with sense leads but not shunt cal)
(tolerance) 7205-75-XX** Mating connector & 4 conductor cable
Sensitivity 300 lb to 2K lb 2 mV/V of rated output (unamplified unit without sense leads but not shunt cal)
7205-83-XX* Mating connector & 6 conductor cable
Sensitivity 5K lb to 100K lb 4 mV/V of rated output (for connection to instrument 7541)
7205-82-XX** Mating connector & 4 conductor cable
Zero balance (tolerance) ±1.0 %
(for connection to instrument 7541)
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Tension/Compression Pancake Load Cell
MECHANICAL CHARACTERISTICS
Nominal load limit
capacity Fz
Model lb N Static overload Weight (lb) Weight with base Flexure
capacity (% of (lb) material
nominal capacity)
3143-P 300 1K 150 1.0 2.5 Aluminum
3143-P 500 2K 150 1.0 2.5 Aluminum
3143-P 1K 5K 150 1.0 2.5 Aluminum
3143-P 2K 10K 150 1.0 2.5 Aluminum
3144-P 5K 22K 150 2.9 6.5 Steel
3144-P 10K 45K 150 2.9 6.5 Steel
3145-P 25K 110K 150 9.1 21.5 Steel
3145-P 50K 200K 150 9.1 21.5 Steel
3146-P 100K 500K 150 23.5 52.5 Steel
Honeywell Honeywell
In-Line Amplifier In-Line Amplifier
Output Input Output Input
Serial Number Serial Number
* XX represents length in feet 100ft maximum * XX represents length in feet 100ft maximum
** XX represents length in feet 20ft maximum ** XX represents length in feet 20ft maximum
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3140-P
MOUNTING DIMENSIONS
Model Capac- Ø A in Ø B in C in D in E F in G in ØH J in K L in
ity (lb) Thread Thread
3143-P-300 300 4.12 1.29 0.13 2.50 1/2-20 1.12 1.25 1.25 0.03 1/2-20 0.88
UNF 3B UNF 3B
3143-P-500 500 4.12 1.29 0.13 2.50 1/2-20 1.12 1.25 1.25 0.03 1/2-20 0.88
UNF 3B UNF 3B
3143-P-1K 1000 4.12 1.29 0.13 2.50 1/2-20 1.12 1.25 1.25 0.03 1/2-20 0.88
UNF 3B UNF 3B
3143-P-2K 2000 4.12 1.29 0.13 2.50 1/2-20 1.12 1.25 1.25 0.03 1/2-20 0.88
UNF 3B UNF 3B
3144-P-5K 5000 4.12 1.29 0.13 2.50 5/8-18 1.12 1.25 1.25 0.03 5/8-18 0.88
UNF 3B UNF 3B
3144-P-10K 10000 4.12 1.29 0.13 2.50 5/8-18 1.12 1.25 1.25 0.03 5/8-18 0.88
UNF 3B UNF 3B
3145-P-25K 25000 6.06 2.34 0.13 3.50 1¼-12 1.50 1.63 1.25 0.03 1¼-12 1.50
UNF 3B UNF 3B
3145-P-50K 50000 6.06 2.58 0.13 3.50 1¼-12 1.50 1.63 2.25 0.03 1¼-12 1.50
UNF 3B UNF 3B
3146-P- 100000 8.00 3.76 0.25 4.50 1¾-12 2.25 2.25 3.00 0.03 1¾-12 1.75
100K UNF 3B UNF 3B
PT02E-10-6P CONNECTOR
ØB ØH
ØA
C
E THD. K THD.
F DEEP G L DEEP
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3140-P Tension/Compression Pancake Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
TYPICAL SYSTEM DIAGRAM order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
In-Line Amplifiers Customer Supplied
(Used with unamplified units only) Chart Recorder Honeywell during the period of coverage, Honeywell will repair
Alarm Panel or replace, at its option, without charge those items it finds
Amplifier Output
Universal In-Line Amplifiers Data Acquisition defective. The foregoing is buyer’s sole remedy and is in lieu
UV +/-5 VDC Computer
of all warranties, expressed or implied, including those of
UV-10 +/-10 VDC PLC
UBP 0 +/-5 VDC merchantability and fitness for a particular purpose. In no
U3W 4-20mA (3 wire)
4-20mA (2 wire)
event shall Honeywell be liable for consequential, special, or
U2W
DIN rail Mount In-Line Amplifiers indirect damages.
DV-05 0 +/- 5 VDC (3 wire) Power Supply
DA-05 4-20mA (3 wire) While we provide application assistance personally, through our
DV10 0 +/- 10 VDC (3 wire)
literature and the Honeywell web site, it is up to the customer to
Honeywell determine the suitability of the product in the application.
In-Line Amplifier
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3167
Tension/Compression Pancake Load Cell
DESCRIPTION
These general purpose designs have exceptional structural Minimum deflection and compactness make these general-
capability to withstand extraneous loads, such as torque, purpose load cells easy to install and use.
bending moments, and side loads.
FEATURES
• Up to 0.05 % accuracy
• 25 lb to 300 lb range
• Integral cable (standard)
• Low sensitivity to extraneous loads
• Low deflection
• Built-in temperature compensation
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3167
MECHANICAL SPECIFICATIONS
Characteristic Measure
Static overload capacity 150 % of nominal capacity
Material Carbon steel
Natural frequency See table
WIRING CODES
Cable
Red (+) excitation
Black (-) excitation
Green (+) output
White (-) output
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static over- Shear FX or Bending MX Torque MZ Deflection at Ringing fre-
load capacity FY (lb) or MY (lb-in) (lb-in) nominal load quency (Hz)
(% of nominal limit (in)
capacity)
25 125 150 150 150 40 0.003 2100
50 200 150 150 150 40 0.003 2800
100 500 150 250 180 40 0.003 3800
200 1K 150 250 180 40 0.003 5400
300 1.5K 150 250 180 40 0.003 7000
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in]
3167 5,72 [2.25] - [1/4-28] 0,95 [0.38] 1,10 [0.44] 1,10 [0.44]
B UNF THD.
C DEEP BOTH ENDS
A +/- H
E
F
D G
J DIA. H
K DIA.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3173
Tension/Compression Pancake Load Cell
DESCRIPTION
The Model 3173 covers the lower capacity ranges of 200 load cells are well suited to materials testing machines and other
pounds force to 3000 pounds force, while exhibiting the high applications requiring a rugged load sensor. Often ideal for high
performance characteristics of stiffness and accuracy. These cycle count applications.
FEATURES
• English threads
• Enhanced accuracy, 0.07 %
• Low deflection
• Fatigue-resistant design and enhanced performance
• Low full-scale capacity
• Low profile
• Decreased sensitivity to extraneous loading
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3173
ENVIRONMENTAL SPECIFICATIONS
Honeywell
Characteristic Measure In-Line Amplifier
Output
Serial Number
Input
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static overload Shear FX or FY Bending MX or Torque MZ Deflection at Ringing fre-
capacity (% of (lb) MY (lb-in) (lb-in) nominal load quency (Hz)
nominal capac- limit (in)
ity)
200 1K 150 100 4471 185 0.003 1500
500 2K 150 100 15625 466 0.003 2440
1K 5K 150 100 15500 911 0.003 3900
2K 10K 150 100 4000 2133 0.001 5500
3K 15K 150 100 5166 2818 0.001 7200
MOUNTING DIMENSIONS
G threads
M cm [in]
screws K
O cm [in]
Q cm [in]
A cm [in]
B cm [in]
C cm [in]
D cm [in]
H cm [in]
N cm [in]
E cm [in]
P cm [in]
Capacity
F cm [in]
L cm [in]
I cm [in]
English
holes J
Bolting
Model
No. of
N [lb]
3173 10,47 7,24 3,23 3,48 0,31 0,15 8.89 0,71 8 3,18 1,27 0,08 2,87 2,21 0,64
900-13.5K
[200-3K]
5/8-18 UNF-3B
1/4-28 hexhead*
[4.12] [2.85] [1.27] [1.37] [0.12] [0.06] [3.5] [0.28] [1.25] [0.50] [0.03] [1.13] [0.87] [0.25]
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Models 3174-3176
Model 3174
DESCRIPTION
Models 3174, 3175, and 3176 are fatigue-resistant, low-profile These load cells are extremely resistant to extraneous bending
tension and compression load cells that are well suited to and side-loading forces. The structure virtually eliminates
materials testing machines and other applications requiring bending strains at the strain gage, minimizing the primary cause
a rugged load sensor, while exhibiting the high performance of load cell failures.
characteristics of stiffness and accuracy.
FEATURES
• English threads
• Enhanced accuracy, up to 0.07 %
• Low deflection
• Fatigue-resistant design and enhanced performance
• Tension/compression capacity
• Low profile
• Low sensitivity to extraneous loading
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3174-3176
ELECTRICAL SPECIFICATIONS
Serial Number
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
Model lb N Static Fatigue Shear FX or Bending MX Torque MZ Deflection Ringing
overload capacity (% FY (lb) or MY (lb-in) (lb-in) at nominal frequency
capacity (% of nominal load limit (Hz)
of nominal capacity) (in)
capacity)
3174 5K 20K 150 100 11K 9K 12K 0.001 6500
3174 10K 50K 150 100 25K 27K 24K 0.001 7200
3174 20K 100K 150 100 55K 58K 35K 0.001 8600
3175 50K 200K 150 100 32K 33K 67K 0.001 12000
3176 100K 500K 150 100 78K 147K 196K 0.001 15000
Honeywell
In-Line Amplifier Honeywell
Output
Serial Number
Input
In-Line Amplifier
Output Input
Serial Number
Display Units
Display Units
Recommended Tension Base
SC500 SC1000 SC2000 Recommended Tension Base
SC2001 SC3004 SC500 SC1000 SC2000
064-LW31496-1
GM NK HH 064-LW31496-2 SC2001 SC3004
7541 7558 7561-PSD GM NK HH
MODEL 3175 7541 7558 7561-PSD
MODEL 3176
2003.1 lb.
OR L1 L2 L3 L4
2003.1 lb.
VALUE CLEAR CHAN TARE OR L1 L2 L3 L4
UP DOWN SETUP ENTER EXIT
VALUE CLEAR CHAN TARE
UP DOWN SETUP ENTER EXIT
RECEP.
PT02E-10-6P (MATING
CONNECTOR FURNISHED)
16
45
MODEL
3174
ONLY
2.25 INCH
A G
5.12 CM
K DIA. THRU
I TAP THRU L NUMBER OF HOLES
EQUALLY SPACED M RECOMMENDED
BOLTING SCREWS
C DIA. I TAP THRU
H
E F
D
Tension bases are recommended for all model 3174, 3175 and 3176 applications.
D When mounting without the tension base, attention must be given to the mating
surface with regard to flatness, hardness and stiffness.
F B DIA.
A DIA.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3397
Tension/Compression Pancake Load Cell
DESCRIPTION
These general purpose designs have exceptional structural Minimum deflection and compactness make these general-
capability to withstand extraneous loads, such as torque, purpose load cells easy to install and use.
bending moments, and side loads.
FEATURES
• Up to 0.05 % accuracy
• 25 lb to 300 lb range
• Low sensitivity to extraneous loads
• Low deflection
• Built-in temperature compensation
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3397
Honeywell
In-Line Amplifier
ENVIRONMENTAL SPECIFICATIONS Output
Serial Number
Input
Characteristic Measure
Display Units
Temperature, operating -54 °C to 93 °C [-65 °F to 200 °F]
SC500 SC1000 SC2000
Temperature, compensated 21 °C to 77 °C [70 °F to 170 °F]
SC2001 SC3004
Temperature effect, zero ±0.002 % of rated output/°F GM NK HH
7541 7558 7561-PSD
Temperature effect, output ±0.002 % of reading/°F MODEL 3397
ELECTRICAL SPECIFICATIONS OR
2003.1 lb.
L1 L2 L3 L4
WIRING CODES
Cable
Red (+) excitation
Black (-) excitation
Green (+) output
White (-) output
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static over- Shear FX or Bending MX Torque MZ Deflection at Ringing fre-
load capacity FY (lb) or MY (lb-in) (lb-in) nominal load quency (Hz)
(% of nominal limit (in)
capacity)
25 125 150 150 150 40 0.003 2100
50 200 150 150 150 40 0.003 2800
100 500 150 250 180 40 0.003 3800
200 1K 150 250 180 40 0.003 5400
300 1.5K 150 250 180 40 0.003 7000
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in]
3397 6,98 [2.75] 0,55 [0.22] 0,32 [0.13] 4,44 [1.75] 5,60 [2.22] - [1/4-28]
A
SPANNER WRENCH
HOLE B DIA.
F THD. C DEEP
G DEEP
BOTH ENDS
RECEP.
PTO2E-10-6P
E
DUAL BRIDGE
OPTIONAL
H DIA.
C J
P
K
L
N DIA.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3127
Tension/Compression Canister Load Cell
DESCRIPTION
The Model 3127 fatigue-resistant load cells are extremely minimizing the primary cause of load cell failure. Dual bridge
resistant to extraneous bending and side loading forces. The option available for feedback control and redundancy.
structure virtually eliminates bending strains at the strain gage,
FEATURES
• Optional dual bridge not shown
• English threads (metric threads available: 3127-118)
• Resist fatigue failure
• Low failure rate
• Multi-beam structure design
• 10000000 N capacity
• Bending moment resistance of 7500000 lb inches
• 450000 lb of shear resistance
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3127
Honeywell
ENVIRONMENTAL SPECIFICATIONS In-Line Amplifier
Output Input
ELECTRICAL SPECIFICATIONS
Characteristic Measure
2003.1 lb.
OR L1 L2 L3 L4
Strain gage type Foil
VALUE CLEAR CHAN TARE
WIRING CODES
Wire
Red (+) excitation
Black (-) excitation
Green (+) output
White (-) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Tension/Compression Canister Load Cell
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static Fatigue Shear FX or Bending MX Torque MZ Deflection Ringing
overload capacity (% FY (lb) or MY (lb-in) (lb-in) at nominal frequency
capacity (% of nominal load limit (Hz)
of nominal capacity) (in)
capacity)
2000K 10M 100 50 450K 7500K 1500K 0.007 1900
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in] G cm [in] H cm [in] J cm [in]
3127 57,15 20,32 [8.0] 16,51 [6.50] 6,35 [2.50] 44,78 43,18 [17] 28,58 16,51 [6.50] 24,77 [9.75]
[22.50] [17.63] [11.25]
K cm [in] L cm [in] M cm [in] N cm [in] P cm [in] Q cm [in] R cm [in] S cm [in] *T cm [in] *U cm [in]
7,62 [3] 30,48 [12] 3,81 [1.50] 6,35 [2.50] 8,89 [3.50] 20,96 [8.25] 1,03 [0.41] 1,27 [0.50] M150-4 M42-3
[6-8] [1.75-12]
J C
G
B A
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3127 Tension/Compression Canister Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3129-121
Tension/Compression Canister Load Cell
DESCRIPTION
The Model 3129-121 fatigue-resistant load cells are extremely minimizing the primary cause of load cell failure. Dual bridge
resistant to extraneous bending and side loading forces. The option available for feedback control and redundancy.
structure virtually eliminates bending strains at the strain gage,
FEATURES
• Optional dual bridge (not shown)
• Metric threads (English threads availble: 3129-112)
• Resist fatigue failure
• Multi-beam structure design
• 1500000 N capacity
• Bending moment resistance of 840000 lb inches
• 65000 lb of shear resistance
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3129-121
WIRING CODES
Wire
Red (+) excitation
Black (-) excitation
Green (+) output
White (-) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Tension/Compression Canister Load Cell
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static Fatigue Shear FX or Bending MX Torque MZ Deflection Ringing
overload capacity (% FY (lb) or MY (lb-in) (lb-in) at nominal frequency
capacity (% of nominal load limit (Hz)
of nominal capacity) (in)
capacity)
150K 750K 150 75 40K 625K 150K 0.004 3000
200K 1M 150 75 55K 730K 260K 0.004 3400
300K 1.5M 150 75 65K 840K 236K 0.004 4100
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in]
3129 25,4 [10] 17,78 [7] 3,81 [1.50] 10,8 [4.25] 19,05 [7.50] 12,70 [5]
J
N THD.
3.0 DEEP M THD. 1/2 DEEP
BOTH ENDS 8 HOLES EQUALLY SPACED
ON H DIA. D
C A
RECEP.
MS-3102E-14S-5P
SPANNER WRENCH HOLES
L DIA.
13/32 DIA. 3/8 DEEP
G 6 HOLES EQUALLY SPACED
B DIA. AT BOTH ENDS
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3129-121 Tension/Compression Canister Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3130-131
Tension/Compression Canister Load Cell
DESCRIPTION
The Model 3130-131 fatigue-resistant load cells are extremely minimizing the primary cause of load cell failure. Dual bridge
resistant to extraneous bending and side loading forces. The option available for feedback control and redundancy.
structure virtually eliminates bending strains at the strain gage,
FEATURES
• Optional dual bridge (not shown)
• Metric threads
• Resist fatigue failure
• Multi-beam structure design
• Capacities to 5000000 N
• Bending moment resistance up to 6110000 lb inches
• Up to 180000 lb of shear resistance
• Flexible mounting configurations
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3130-131
Standard calibration Tension (+) and compression (-) DA-05 4-20mA (3 wire)
DV10 0 +/- 10 VDC (3 wire)
Characteristic Measure
Output Input
Serial Number
ELECTRICAL SPECIFICATIONS
Characteristic Measure
2003.1 lb.
Strain gage type Foil OR L1 L2 L3 L4
VALUE CLEAR CHAN TARE
Static overload capacity 150 % of nominal capacity * XX represents length in feet 100ft maximum
** XX represents length in feet 20ft maximum
Material Carbon steel
Fatigue life (0 to full fatigue 100 x 106 cycles
load)
Fatigue life (full fatigue ten- 50 x 106 cycles
sion to compression)
Natural frequency See table
WIRING CODES
Wire
Red (+) excitation
Black (-) excitation
Green (+) output
White (-) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Tension/Compression Canister Load Cell
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static Fatigue Shear FX or Bending MX Torque MZ Deflection Ringing
overload capacity (% FY (lb) or MY (lb-in) (lb-in) at nominal frequency
capacity (% of nominal load limit (Hz)
of nominal capacity) (in)
capacity)
500K 2M 150 50 94K 4530K 820K 0.006 2500
800K 3.5M 150 50 180K 5450K 1050K 0.006 3100
1000K 5M 150 50 180K 6110K 1100K 0.006 3600
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in] G cm [in]
3130 31,75 [12.50] 3,81 [1.50] 17,78 [7.0] 5,08 [2.0] 1,91 [0.75] 32,29 [12.75] 31,12 [12.25]
C A
L
Q THD. 2.0 DEEP
8 HOLES EQUALLY SPACED
ON N DIA. BOTH ENDS SPANNER WRENCH HOLES
G DIA. BOTH ENDS
RECEP. 13/32 DIA. 3/8 DEEP 4 HOLES
M F DIA. EQUALLY SPACED BOTH ENDS
MS-3102E-14S-5P
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3130-131 Tension/Compression Canister Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3156
Tension/Compression Canister Load Cell
DESCRIPTION
The Model 3156 fatigue-resistant load cells are extremely minimizing the primary cause of load cell failure. Dual bridge
resistant to extraneous bending and side loading forces. The option available for feedback control and redundancy.
structure virtually eliminates bending strains at the strain gage,
FEATURES
• English threads (metric configuration available: 3156-133)
• Resist fatigue failure
• Minimize bending strains
• Dual bridges available on all models
• Multi-beam structure design
• Enhanced resistance to side loads and bending moments
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3156
Honeywell
ENVIRONMENTAL SPECIFICATIONS In-Line Amplifier
Output Input
Serial Number
Characteristic Measure
Temperature, operating -54 °C to 93 °C [-65 °F to 200 °F] Display Units
Temperature, compensated 21 °C to 77 °C [70 °F to 170 °F]
SC500 SC1000 SC2000
Temperature effect, zero ±0.003 % of rated output/°F SC2001 SC3004
GM NK HH
Temperature effect, output ±0.003 % of reading/°F MODEL 3156 7541 7558 7561-PSD
ELECTRICAL SPECIFICATIONS
Characteristic Measure OR
2003.1 lb.
L1 L2 L3 L4
Strain gage type Foil VALUE
UP
CLEAR
DOWN SETUP
CHAN
ENTER
TARE
EXIT
WIRING CODES
Wire
Red (+) excitation
Black (-) excitation
Green (+) output
White (-) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Tension/Compression Canister Load Cell
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static Fatigue Shear FX or Bending MX Torque MZ Deflection Ringing
overload capacity (% FY (lb) or MY (lb-in) (lb-in) at nominal frequency
capacity (% of nominal load limit (Hz)
of nominal capacity) (in)
capacity)
25K 100K 150 100 2K 68K 10K 0.003 2100
50K 200K 150 100 6K 130K 20K 0.003 3000
100K 500K 150 100 10K 220K 85K 0.003 4200
150K 750K 150 100 20K 220K 85K 0.003 4800
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in] G cm [in]
3156 17,78 [7] 13,97 [5.50] 8,89 [3.50] 5,41 [2.13] 12,07 [4.75] 2,87 [1.13] 13,84 [5.45]
R THD.
M DEEP
BOTH ENDS P THD. N DEEP 6 HOLES
EQUALLY SPACED ON J DIA.
BOTH ENDS
A
E
C
F
D
DIA.
B
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3156 Tension/Compression Canister Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RF
Rod End In-line Tension Load Cell
DESCRIPTION
Model RF, with female threads, is a high output rod end load cell The optional high output signal offers resistance to electrical
designed to be mounted inline to the load axis to measure ten- noise as well as additional signal resolution. Additional options
sion. The outputs for these load cells are ±5 Vdc or 10 Vdc, or include an internal buffered shunt calibration circuit for ease of
4 mA to 20 mA (two wire) all calibrated in tension. The mount- setup with an associated indicator, and a variety of thread selec-
ing thread configurations and the all welded stainless steel tions, including metric sizes.
construction make these tension load cells ideal for a variety of
rugged field applications as well as in the laboratory.
FEATURES
• 2000 lb to 200000 lb range
• Female/female threads
• Stainless steel, all-welded construction
• 0 Vdc to 5 Vdc or 4 mA to 20 mA outputs
• Up to 0.15 % linearity
• CE approved10
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RF
PERFORMANCE SPECIFICATIONS MECHANICAL SPECIFICATIONS
Characteristic Measure Characteristic Measure
Load ranges12 2000 lb to 200000 lb Maximum allowable load 150 % FS1
Linearity Weight See table
±0.2 % full scale
100 lb to 1000 lb
Material Stainless steel
Linearity
±0.15 % full scale Deflection full scale See table
2000 lb to 50000 lb
Natural frequency See table
Linearity
±0.2 % full scale
75000 lb to 20000 lb
Hysteresis RANGE CODES
±0.2 % full scale
100 lb to 1000 lb Range Available ranges Range Available ranges
Hysteresis Code Code
±0.15 % full scale
2000 lb to 50000 lb DL 2000 lb EL 20000 lb
Hysteresis DN 3000 lb EN 30000 lb
±0.2 % full scale
75000 lb to 20000 lb
DP 4000 lb EP 50000 lb
Non-repeatability ± 0.05 % full scale
DR 5000 lb ER 75000 lb
Output 2 mV/V
DT 75000 lb ET 100000 lb
Operation Tension
DV 10000 lb FJ 150000 lb
Resolution Infinite
EJ 15000 lb FL 200000 lb
ENVIRONMENTAL SPECIFICATIONS
WIRING CODES
Characteristic Measure
Connector Unamplified (Std.)
Temperature, operating -54 °C to 121 °C [-65 °F to 250 °F]
A (+) excitation
Temperature, compensated 15 °C to 71 °C [60 °F to 160 °F]
B (+) excitation
Temperature effect, zero 0.005 % full scale/°F
C (-) excitation
Temperature effect, span 0.005 % full scale/°F
D (-) excitation
E (-) output
ELECTRICAL SPECIFICATIONS
F (+) output
Characteristic Measure
Strain gage type Bonded foil DEFLECTIONS AND RINGING FREQUENCIES
Excitation (calibration) 10 Vdc
Capacity (lb) Deflection at Ringing fre- Weight kg
Excitation (acceptable) Up to 15 Vdc or Vac full scale mm quency (Hz) [lb]
Insulation resistance 5000 mOhm @ 50 Vdc [in]
Bridge resistance (toler- 350 ohm 2000 0,076 [0.003] 5000 0,58 [1.3]
ance) 3000 0,076 [0.003] 5000 0,58 [1.3]
Zero balance (tolerance) ±1% full scale 4000 0,076 [0.003] 5100 0,58 [1.3]
Shunt calibration data Included 5000 0,076 [0.003] 5200 0,58 [1.3]
Electrical termination (std) PTIH-10-6P or equivalent (hermetic 7500 0,076 [0.003] 8000 0,72 [1.6]
2000 lb to 50000 lb stainless)
10000 0,076 [0.003] 8500 0,72 [1.6]
Electrical termination (std) MS3102E-14S-6P or equivalent
15000 0,076 [0.003] 9000 0,72 [1.6]
75000 lb to 200000 lb
20000 0,102 [0.004] 9000 0,77 [1.7]
Mating connector (not in- PT06A-10-6S or equivalent (AA111)
cluded) 2000 lb to 50000 lb 30000 0,102 [0.004] 8000 1,58 [3.5]
Mating connector (not MS3106A-14S-6S or equivalent (AA121) 50000 0,127 [0.005] 8000 1,67 [3.7]
included) 75000 lb to 75000 to 0,152 [0.006] 3500 18,00 [39.7]
200000 lb 100000
150000 to 0,178 [0.007] 3000 33,02 [72.8]
200000
Wiring code: R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
cable5,6,7 Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RH
Rod End In-line Tension Load Cell
DESCRIPTION
Model RH, with male and female threads, is a high output rod The optional high output signal offers resistance to electrical
end load cell designed to be mounted inline to the load axis to noise as well as additional signal resolution. Additional options
measure tension. The outputs for these load cells are ±5 Vdc or include an internal buffered shunt calibration circuit for ease of
10 Vdc, or 4 mA to 20 mA (two wire) all calibrated in tension. The setup with an associated indicator, and a variety of thread selec-
mounting thread configurations and the all welded stainless steel tions, including metric sizes.
construction make these tension load cells ideal for a variety of
rugged field applications as well as in the laboratory.
FEATURES
• 2000 lb to 200000 lb range
• Male/female threads
• Stainless steel, all-welded construction
• 0 Vdc to 5 Vdc or 4 mA to 20 mA outputs
• Up to 0.15 % linearity
• CE approved10
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RH
PERFORMANCE SPECIFICATIONS MECHANICAL SPECIFICATIONS
Characteristic Measure Characteristic Measure
Load ranges12 2000 lb to 200000 lb Maximum allowable load 150 % FS1
Linearity Weight See table
±0.2 % full scale
100 lb to 1000 lb
Material Stainless steel
Linearity
±0.15 % full scale Deflection full scale See table
2000 lb to 50000 lb
Natural frequency See table
Linearity
±0.2 % full scale
75000 lb to 20000 lb
Hysteresis RANGE CODES
±0.2 % full scale
100 lb to 1000 lb Range Available ranges Range Available ranges
Hysteresis Code Code
±0.15 % full scale
2000 lb to 50000 lb DL 2000 lb EL 20000 lb
Hysteresis DN 3000 lb EN 30000 lb
±0.2 % full scale
75000 lb to 20000 lb
DP 4000 lb EP 50000 lb
Non-repeatability ± 0.05 % full scale
DR 5000 lb ER 75000 lb
Output 2 mV/V
DT 75000 lb ET 100000 lb
Operation Tension
DV 10000 lb FJ 150000 lb
Resolution Infinite
EJ 15000 lb FL 200000 lb
ENVIRONMENTAL SPECIFICATIONS
WIRING CODES
Characteristic Measure
Connector Unamplified (Std.)
Temperature, operating -54 °C to 121 °C [-65 °F to 250 °F]
A (+) excitation
Temperature, compensated 15 °C to 71 °C [60 °F to 160 °F]
B (+) excitation
Temperature effect, zero 0.005 % full scale/°F
C (-) excitation
Temperature effect, span 0.005 % full scale/°F
D (-) excitation
E (-) output
ELECTRICAL SPECIFICATIONS
F (+) output
Characteristic Measure
Strain gage type Bonded foil DEFLECTIONS AND RINGING FREQUENCIES
Excitation (calibration) 10 Vdc
Capacity (lb) Deflection at Ringing fre- Weight kg
Excitation (acceptable) Up to 15 Vdc or Vac full scale mm quency (Hz) [lb]
Insulation resistance 5000 mOhm @ 50 Vdc [in]
Bridge resistance (toler- 350 ohm 2000 0,076 [0.003] 5000 0,49 [1.1]
ance) 3000 0,076 [0.003] 5000 0,49 [1.1]
Zero balance (tolerance) ±1% full scale 4000 0,076 [0.003] 5100 0,49 [1.1]
Shunt calibration data Included 5000 0,076 [0.003] 5200 0,49 [1.1]
Electrical termination (std) PTIH-10-6P or equivalent (hermetic 7500 0,102 [0.004] 7500 0,81 [1.8]
2000 lb to 50000 lb stainless)
10000 0,102 [0.004] 7600 0,81 [1.8]
Electrical termination (std) MS3102E-14S-6P or equivalent
15000 0,127 [0.005] 8000 0,81 [1.8]
75000 lb to 200000 lb
20000 0,127 [0.005] 9800 0,81 [1.8]
Mating connector (not in- PT06A-10-6S or equivalent (AA111)
cluded) 2000 lb to 50000 lb 30000 0,127 [0.005] 8000 1,99 [4.4]
Mating connector (not MS3106A-14S-6S or equivalent (AA121) 50000 0,127 [0.005] 8200 1,99 [4.4]
included) 75000 lb to 75000 to 0,152 [0.006] 5000 16,01 [35.3]
200000 lb 100000
150000 to 0,178 [0.007] 4200 18,00 [39.7]
200000
Wiring code: R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
cable5,6,7 Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RM
Rod End In-line Tension Load Cell
DESCRIPTION
Model RM, with male threads, is a high output rod end load cell The optional high output signal offers resistance to electrical
designed to be mounted inline to the load axis to measure ten- noise as well as additional signal resolution. Additional options
sion. The outputs for these load cells are ±5 Vdc or 10 Vdc, or include an internal buffered shunt calibration circuit for ease of
4 mA to 20 mA (two wire) all calibrated in tension. The mount- setup with an associated indicator, and a variety of thread selec-
ing thread configurations and the all welded stainless steel tions, including metric sizes.
construction make these tension load cells ideal for a variety of
rugged field applications as well as in the laboratory.
FEATURES
• 2000 lb to 200000 lb range
• Male/male threads
• Stainless steel, all-welded construction
• 0 Vdc to 5 Vdc or 4 mA to 20 mA outputs
• Up to 0.15 % linearity
• CE approved10
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RM
PERFORMANCE SPECIFICATIONS MECHANICAL SPECIFICATIONS
Characteristic Measure Characteristic Measure
Load ranges11 2000 lb to 200000 lb1 Maximum allowable load 150 % FS1
Linearity Weight See table
±0.2 % full scale
100 lb to 1000 lb
Material Stainless steel
Linearity
±0.15 % full scale Deflection full scale See table
2000 lb to 50000 lb
Natural frequency See table
Linearity
±0.2 % full scale
75000 lb to 20000 lb
Hysteresis RANGE CODES
±0.2 % full scale
100 lb to 1000 lb Range Available ranges Range Available ranges
Hysteresis Code Code
±0.15 % full scale
2000 lb to 50000 lb DL 2000 lb EL 20000 lb
Hysteresis DN 3000 lb EN 30000 lb
±0.2 % full scale
75000 lb to 20000 lb
DP 4000 lb EP 50000 lb
Non-repeatability ± 0.05 % full scale
DR 5000 lb ER 75000 lb
Output (tolerance) 2 mV/V
DT 75000 lb ET 100000 lb
Operation Tension
DV 10000 lb FJ 150000 lb
Resolution Infinite
EJ 15000 lb FL 200000 lb
ENVIRONMENTAL SPECIFICATIONS
WIRING CODES
Characteristic Measure
Connector Unamplified (Std.)
Temperature, operating -54 °C to 121 °C [-65 °F to 250 °F]
A (+) excitation
Temperature, compensated 15 °C to 71 °C [60 °F to 160 °F]
B (+) excitation
Temperature effect, zero 0.005 % full scale/°F
C (-) excitation
Temperature effect, span 0.005 % full scale/°F
D (-) excitation
E (-) output
ELECTRICAL SPECIFICATIONS
F (+) output
Characteristic Measure
Strain gage type Bonded foil DEFLECTIONS AND RINGING FREQUENCIES
Excitation (calibration) 10 Vdc
Capacity (lb) Deflection at Ringing fre- Weight kg
Excitation (acceptable) Up to 15 Vdc or Vac full scale mm quency (Hz) [lb]
Insulation resistance 5000 mOhm @ 50 Vdc [in]
Bridge resistance (toler- 350 ohm 2000 0,076 [0.003] 5000 0,45 [1.0]
ance) 3000 0,076 [0.003] 5000 0,45 [1.0]
Zero balance (tolerance) ±1% full scale 4000 0,076 [0.003] 5100 0,45 [1.0]
Shunt calibration data Included 5000 0,076 [0.003] 5200 0,45 [1.0]
Electrical termination (std) PTIH-10-6P or equivalent (hermetic 7500 0,102 [0.004] 7500 0,68 [1.5]
2000 lb to 50000 lb stainless)
10000 0,102 [0.004] 7600 0,68 [1.5]
Electrical termination (std) MS3102E-14S-6P or equivalent
15000 0,127 [0.005] 8000 0,68 [1.5]
75000 lb to 200000 lb
20000 0,127 [0.005] 9800 0,68 [1.5]
Mating connector (not in- PT06A-10-6S or equivalent (AA111)
cluded) 2000 lb to 50000 lb 30000 0,127 [0.005] 8000 1,90 [4.2]
Mating connector (not MS3106A-14S-6S or equivalent (AA121) 50000 0,127 [0.005] 8200 1,90 [4.2]
included) 75000 lb to 75000 to 0,152 [0.006] 5000 7,34 [16.5]
200000 lb 100000
150000 to 0,178 [0.007] 4200 16,01 [35.3]
200000
Wiring code: R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
cable5,6,7 Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RGF
Rod End In-line Compression/Tension Load Cell
DESCRIPTION
The Model RGF In-Line load cells are high quality, stainless steel completely controlled. The flexible mounting options make appli-
rugged load cells capable of withstanding significant off-axis cations easier to implement, and the all stainless steel, hermetic
loads, making them an ideal choice for in-line compression mea- construction is well suited to corrosive and very high humidity
surement or tension measurement where side loading cannot be environments.
FEATURES
• 2000 lb to 50000 lb range
• Female/female threads
• Stainless steel, all-welded construction
• 1 mV/V nominal (standard); 0 Vdc to 5 Vdc or 4 mA to 20
mA outputs (optional)
• Compression/tension
• 0.25 % accuracy
• CE approved10
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RGF
PERFORMANCE SPECIFICATIONS RANGE CODES
Characteristic Measure Range Code Available ranges
Load ranges11 2000, 3000, 5000, 10000, 15000, 25000, DL 2000 lb
50000 lb
DN 3000 lb
Accuracy ±0.25 % full scale1
DR 5000 lb
Linearity ±0.25 % full scale
DV 10000 lb
Hysteresis ±0.25 % full scale
EJ 15000 lb
Non-repeatability ± 0.05 % full scale
EM 25000 lb
Output (tolerance) 1 mV/V (nominal)
EP 50000 lb
Operation Tension/compression
Resolution Infinite
WIRING CODES
Connector Unamplified (Std.)
ENVIRONMENTAL SPECIFICATIONS A (+) excitation
Characteristic Measure B (+) excitation
Temperature, operating -54 °C to 121 °C [-65 °F to 250 °F] C (-) excitation
Temperature, compensated 15 °C to 71 °C [60 °F to 160 °F] D (-) excitation
Temperature effect, zero 0.005 % full scale/°F E (-) output
Temperature effect, span 0.005 % full scale/°F F (+) output
ELECTRICAL SPECIFICATIONS
Characteristic Measure
DEFLECTIONS AND RINGING FREQUENCIES
Strain gage type Bonded foil Capacity (lb) Deflection at Ringing fre- Weight kg
full scale mm quency (Hz) [lb]
Excitation (calibration) 10 Vdc [in]
Excitation (acceptable) Up to 15 Vdc or Vac 2000 0,025 [0.001] 10000 0,55 [1.2]
Insulation resistance 5000 mOhm @ 50 Vdc 3000 0,025 [0.001] 12000 0,55 [1.2]
Bridge resistance (toler- 700 ohm 5000 0,050 [0.002] 15000 0,63 [1.4]
ance)
10000 0,050 [0.002] 10000 1,3 [2.9]
Shunt calibration data Included
15000 0,050 [0.002] 10000 1,3 [2.9]
Electrical termination (std) PTIH-10-6P or equivalent (hermetic
stainless) 25000 0,050 [0.002] 6500 4,3 [9.5]
50000 0,076 [0.003] 7000 4,49 [9.9]
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % FS1
Case material Stainless steel
Life cycles (approx) >10 million cycles
Deflection full scale 0,076 mm [0.003 in]
Wiring code: R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
cable4,5,6 Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RGH
Rod End In-line Compression/Tension Load Cell
DESCRIPTION
The Model RGH In-Line load cells are high quality, stainless cannot be completely controlled. The flexible mounting options
steel, rugged load cells capable of withstanding significant make applications easier to implement, and the all stainless
off-axis loads, making them an ideal choice for in-line compres- steel, hermetic construction is well suited to corrosive and very
sion measurement or tension measurement where side loading high humidity environments.
FEATURES
• 2000 lb to 50000 lb range
• Male/female threads
• Stainless steel, all-welded construction
• 1 mV/V nominal (standard); 0 Vdc to 5 Vdc or 4 mA to 20
mA outputs (optional)
• Compression/tension
• 0.25 % accuracy
• CE approved10
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RGH
PERFORMANCE SPECIFICATIONS RANGE CODES
Characteristic Measure Range Code Available ranges
Load ranges 11
2000, 3000, 4000, 5000, 10000, 15000, DL 2000 lb
25000, 50000 lb
DN 3000 lb
Accuracy ±0.25 % full scale1
DP 4000 lb
Linearity ±0.25 % full scale
DR 5000 lb
Hysteresis ±0.25 % full scale
DV 10000 lb
Non-repeatability ± 0.05 % full scale
EJ 15000 lb
Output (tolerance) 1 mV/V (nominal)
EM 25000 lb
Operation Tension/compression
EP 50000 lb
Resolution Infinite
WIRING CODES
ENVIRONMENTAL SPECIFICATIONS Connector Unamplified (Std.)
Characteristic Measure A (+) excitation
Temperature, operating -54 °C to 121 °C [-65 °F to 250 °F] B (+) excitation
Temperature, compensated 15 °C to 71 °C [60 °F to 160 °F] C (-) excitation
Temperature effect, zero 0.005 % full scale/°F D (-) excitation
Temperature effect, span 0.005 % full scale/°F E (-) output
F (+) output
ELECTRICAL SPECIFICATIONS
Characteristic Measure
Strain gage type Bonded foil
DEFLECTIONS AND RINGING FREQUENCIES
Excitation (calibration) 10 Vdc Capacity (lb) Deflection at Ringing fre- Weight kg
full scale mm quency (Hz) [lb]
Excitation (acceptable) Up to 15 Vdc or Vac [in]
Insulation resistance 5000 mOhm @ 50 Vdc 2000 0,025 [0.001] 10000 0,55 [1.2]
Bridge resistance (toler- 700 ohm 3000 0,025 [0.001] 12000 0,55 [1.2]
ance)
4000 0.038 [0.0015] 13000 0,59 [1.3]
Shunt calibration data Included
5000 0,050 [0.002] 15000 0,63 [1.4]
Electrical termination (std) PTIH-10-6P or equivalent (hermetic
stainless) 10000 0,050 [0.002] 10000 1,3 [2.9]
15000 0,050 [0.002] 10000 1,3 [2.9]
25000 0,050 [0.002] 6500 4,3 [9.5]
50000 0,076 [0.003] 7000 4,3 [9.5]
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % FS1
Case material Stainless steel
Life cycles (approx) >10 million cycles
Deflection full scale 0,076 mm [0.003 in]
Wiring code: R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
cable4,5,6 Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this datasheet is for
reference only. DO NOT USE this document as product
Find out more installation information.
Honeywell serves its customers • Complete installation, operation and maintenance
through a worldwide network of information is provided in the instructions supplied with
each product.
sales offices, representatives
Failure to comply with these instructions could result in
and distributors. For application
death or serious injury.
assistance, current specifica-
tions, pricing or name of the
nearest Authorized Distributor,
contact your local sales office.
To learn more about Honeywell’s
test and measurement products,
call +1-614-850-5000, visit
www.honeywell.com/sensotec,
or e-mail inquiries to
info.tm@honeywell.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RGM
Rod End In-line Tension/Compression Load Cell
DESCRIPTION
The Model RGM In-Line load cells are high quality, stainless cannot be completely controlled. The flexible mounting options
steel, rugged load cells capable of withstanding significant make applications easier to implement, and the all stainless
off-axis loads, making them an ideal choice for in-line compres- steel, hermetic construction is well suited to corrosive and very
sion measurement or tension measurement where side loading high humidity environments.
FEATURES
• 2000 lb to 50000 lb range
• Male/male threads
• Stainless steel, all-welded construction
• 1 mV/V nominal (standard); 0 Vdc to 5 Vdc or 4 mA to 20
mA outputs (optional)
• Compression/tension
• 0.25 % accuracy
• CE approved10
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model RGM
PERFORMANCE SPECIFICATIONS RANGE CODES
Characteristic Measure Range Code Available ranges
Load ranges 11
2000, 3000, 4000, 5000, 10000, 15000, DL 2000 lb
25000, 50000 lb
DN 3000 lb
Accuracy ±0.25 % full scale
DP 4000 lb
Linearity ±0.25 % full scale
DR 5000 lb
Hysteresis ±0.25 % full scale
DV 10000 lb
Non-repeatability ± 0.05 % full scale
EJ 15000 lb
Output (tolerance) 1 mV/V (nominal)
EM 25000 lb
Operation Tension/compression
EP 50000 lb
Resolution Infinite
WIRING CODES
ENVIRONMENTAL SPECIFICATIONS Connector Unamplified (Std.)
Characteristic Measure A (+) excitation
Temperature, operating -54 °C to 121 °C [-65 °F to 250 °F] B (+) excitation
Temperature, compensated 15 °C to 71 °C [60 °F to 160 °F] C (-) excitation
Temperature effect, zero 0.005 % full scale/°F D (-) excitation
Temperature effect, span 0.005 % full scale/°F E (-) output
F (+) output
ELECTRICAL SPECIFICATIONS
Characteristic Measure
Strain gage type Bonded foil
DEFLECTIONS AND RINGING FREQUENCIES
Excitation (calibration) 10 Vdc Capacity (lb) Deflection at Ringing fre- Weight kg
full scale mm quency (Hz) [lb]
Excitation (acceptable) Up to 15 Vdc or Vac [in]
Insulation resistance 5000 mOhm @ 50 Vdc 2000 0,025 [0.001] 10000 0,55 [1.2]
Bridge resistance (toler- 700 ohm 3000 0,025 [0.001] 12000 0,55 [1.2]
ance)
4000 0.038 [0.0015] 13000 0,59 [1.3]
Zero balance (tolerance) ±3 % full scale
5000 0,050 [0.002] 15000 0,63 [1.4]
Shunt calibration data Included
10000 0,050 [0.002] 10000 1,3 [2.9]
Electrical termination (std) PTIH-10-6P or equivalent (hermetic
stainless) 15000 0,050 [0.002] 10000 1,3 [2.9]
25000 0,050 [0.002] 6500 4,3 [9.5]
50000 0,076 [0.003] 7000 4,3 [9.5]
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % FS1
Weight See table
Material Stainless steel
Life cycles (approx) >10 million cycles
Deflection full scale See table
Natural frequency See table
Wiring code: R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
cable4,5,6 Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3124
Tension/Compression In-Line Load Cell
DESCRIPTION
The small-diameter, cost-efficient load cells are designed to They may be directly attached to the piston rod of a hydraulic
be used in applications that require an ability to mount in an cylinder. Side-mounted cable connectors allow cable assemblies
existing system with restricted working area. They are commonly to be supported without affecting movement of the cell during
used in fluid power transfer systems. Their low cost and ease of tension or compression loading.
mounting allow simultaneous testing of multi-element systems.
FEATURES
• 5000 lb to 25000 lb range
• 0.25 % non-linearity
• 0.15 % hysteresis
• Adapts directly to hydraulic cylinder
• Small diameter allows mounting in restricted areas
• Low deflection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3124
2003.1 lb.
MECHANICAL SPECIFICATIONS OR L1 L2 L3 L4
VALUE CLEAR CHAN TARE
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Tension/Compression In-Line Load Cell
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static Fatigue Shear FX or Bending MX Torque MZ Deflection Ringing
overload capacity (% FY (lb) or MY (lb-in) (lb-in) at nominal frequency
capacity (% of nominal load limit (Hz)
of nominal capacity) (in)
capacity)
5K 20K 150 n/a 250 750 15000 0.005 4600
10K 50K 150 n/a 250 700 1100 0.005 6400
15K 75K 150 n/a 450 1300 2100 0.005 7700
20K 100K 150 n/a 650 2000 3000 0.005 8800
25K 125K 150 n/a 950 2700 4500 0.005 9600
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in] G cm [in] H cm [in]
3124 11,43 [4.50] 2,54 [1.0] 0,97 [0.38] 2,06 [0.81] 3,81 [1.50] 3,51 [1.38] 6,20 [2.44] 4,37 [1.72]
RECEP.
MS-3102E-14S-5P
E
HEX
1.0-14 THD. H
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3124 Tension/Compression In-Line Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3161
Tension/Compression In-Line Load Cell
DESCRIPTION
The small-diameter, cost-efficient, fatigue-resistant load cells They may be directly attached to the piston rod of a hydraulic
are designed to be used in applications that require an ability to cylinder. Side-mounted cable connectors allow cable assemblies
mount in an existing system with restricted working area. They to be supported without affecting movement of the cell during
are commonly used in fluid power transfer systems. Their low tension or compression loading.
cost and ease of mounting allow simultaneous testing of multi-
element systems.
FEATURES
• 2000 lb to 25000 lb range
• 0.15 % linearity
• 0.1 % hysteresis
• Fatigue resistant
• Adapts directly to hydraulic cylinder
• Small diameter allows mounting in restricted areas
• Low deflection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3161
Characteristic Measure
Output Input
Serial Number
Number of bridges 1 or 2
Zero balance ±1.0 %
2003.1 lb.
OR L1 L2 L3 L4
VALUE CLEAR CHAN TARE
Characteristic Measure
Static overload capacity 150 % of nominal capacity Mating Connectors & Cables
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Tension/Compression In-Line Load Cell
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static Fatigue Shear FX or Bending MX Torque MZ Deflection Ringing
overload capacity (% FY (lb) or MY (lb-in) (lb-in) at nominal frequency
capacity (% of nominal load limit (Hz)
of nominal capacity) (in)
capacity)
2K 10K 150 100 850 3800 3500 0.003 5000
5K 20K 150 100 850 3800 3500 0.003 6200
10K 50K 150 100 850 3800 3500 0.003 7100
25K 125K 150 100 2040 6750 9600 0.003 11000
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in] G cm [in] H cm [in]
3161 17,48 [6.88] 2,54 [1.0] 11,28 [4.44] 4,29 [1.69] 6,05 [2.38] 1,27 [0.50] 4,14 [1.63] 0,64 [0.25]
RECEP.
PT02E-10-6P
1.0-14 THD.
OPTIONAL B DEEP
DUAL BRIDGE
D 1.0-14 THD.
C OPTIONAL
DUAL BRIDGE
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3161 Tension/Compression In-Line Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3336
Tension/Compression Donut Load Cell
DESCRIPTION
Model 3336 Tension/Compression Donut Load Cell features a The precision design and manufacture of this versatile
smooth thru-hole design for use in applications which require the transducer style is the result of our experience in the metal
load structure to pass through the cell. The hollow load cells are working industry and automotive applications.
available for tension-compression loads in capacities of 5K, 10K
and 20K lbs.
FEATURES
• 5000 lb to 5000 lb range
• Thru-hole design
• Compact column construction
• mV/V output
• 0.25 % linearity
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3336
Honeywell
ENVIRONMENTAL SPECIFICATIONS In-Line Amplifier
Output Input
Serial Number
Characteristic Measure
Temperature, operating -54 °C to 93 °C [-65 °F to 200 °F] Display Units
Temperature, compensated 21 °C to 77 °C [70 °F to 170 °F] SC500 SC1000 SC2000
Temperature effect, zero ±0.002 % of rated output/°F SC2001 SC3004
GM NK HH
Temperature effect, output ±0.002 % of reading/°F 7541 7558 7561-PSD
MODEL 3336
ELECTRICAL SPECIFICATIONS
2003.1 lb.
Characteristic Measure OR L1 L2 L3 L4
WIRING CODES
Cable
Red (+) excitation
Black (-) excitation
Green (+) output
White (-) output
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static over- Shear FX or Bending MX Torque MZ Deflection at Ringing fre-
load capacity FY (lb) or MY (lb-in) (lb-in) nominal load quency (Hz)
(% of nominal limit (in)
capacity)
5K 20K 150 550 12K 1850 0.005 1100
10K 50K 150 1400 31K 3750 0.005 1500
20K 100K 150 2650 62K 14K 0.005 2200
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in]
3336 22,86 [9] 12,70 [5] 8,26 [3.25] 1,91 [0.75] 12,40 [4.88] 17,78 [7]
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3632
Compression Donut Load Cell
DESCRIPTION
Model 3632 Compression Donut Load Cell features a smooth available for compression only loads in capacities of 25K, 50K
thru-hole design for use in applications which require the load and 100K lbs. For optimum performance, this load cell must be
structure to pass through the cell. The hollow load cells are mounted between load surfaces which are flat and parallel.
FEATURES
• 25000 lb to 100000 lb range
• Thru-hole design
• Compact column construction
• mV/V output
• 0.15 % linearity
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3632
Honeywell
ENVIRONMENTAL SPECIFICATIONS In-Line Amplifier
Output
Serial Number
Input
Characteristic Measure
Temperature, operating -54 °C to 93 °C [-65 °F to 200 °F] Display Units
Temperature, compensated 21 °C to 77 °C [70 °F to 170 °F] SC500 SC1000 SC2000
Temperature effect, zero ±0.002 % of rated output/°F SC2001 SC3004
GM NK HH
Temperature effect, output ±0.002 % of reading/°F 7541 7558 7561-PSD
MODEL 3632
ELECTRICAL SPECIFICATIONS
2003.1 lb.
Characteristic Measure OR L1 L2 L3 L4
VALUE CLEAR CHAN TARE
WIRING CODES
Cable
Red (+) excitation
Black (-) excitation
Green (+) output
White (-) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Compression Donut Load Cell
NATURAL FREQUENCY
Nominal load limit Static extraneous load limits
capacity Fz
lb N Static over- Shear FX or Bending MX Torque MZ Deflection at Ringing fre-
load capacity FY (lb) or MY (lb-in) (lb-in) nominal load quency (Hz)
(% of nominal limit (in)
capacity)
25K 125K 150 2750 18K 3K 0.005 5000
50K 200K 150 5500 36K 13K 0.005 7000
100K 500K 150 13K 91K 27K 0.005 10000
MOUNTING DIMENSIONS
Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in] G cm [in] H cm [in]
3632 10,16 [4] 5,08 [2] 7,62 [3] 5,08 [2] 2,54 [1] 8,26 [3.25] 0,15 [0.06] 4,78 [1.88]
A DIA.
B DIA.
RECEP.
PT02E-10-6P
F
E G
D H
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3632 Compression Donut Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. This unit calibrated to Imperial (non-Metric) units.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model MPB
High Capacity Compact Compression Load Cell
DESCRIPTION
The compact Model MPB Load Cells are designed for Applications include impact testing and mine shaft roof
applications requiring high capacity yet where space restrictions simulations. The diameter of these load cells range between
require that the cell be small in size. The Model MPB will 1.25 in and 10 in while the height ranges between approximately
measure compression load forces in ranges between 15,000 to 0.63 in and 14 in depending on the load range desired.
2,000,000 pounds.
FEATURES
• 8 ton to 1000 ton range
• Stainless steel
• mV/V output
• 0.25 % accuracy
• CE approved
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model MPB
ELECTRICAL SPECIFICATIONS
Wire
Characteristic Measure
Red (+) excitation
Strain gage type Bonded foil
Black (-) excitation
Excitation (calibration) 10 Vdc
Green (-) output
Insulation resistance 5,000 mOhm @ 50 Vdc
White (+) output
Bridge resistance (toler- 350 ohm (nominal)
ance)
Zero balance (tolerance) ± 1% of full scale TYPICAL SYSTEM DIAGRAM
Shunt calibration data Included
Electrical termination (std) Cable
1 ton to 5 ton
Electrical termination (std) Connector
10 ton to 1000 ton
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % FS3
Material All welded stainless steel
Life cycles (approx.) 1 million cycles
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
High Capacity Compact Compression Load Cell
INTERNAL AMPLIFIERS
Amplifier Voltage out- Voltage out- Vehicle volt- Vehicle volt- Current three- Current two- Intrinsically
specifica- put: put: age output: age output: wire: wire: safe amp: Op-
tions Option 2a Option 2b Option 2c Option 2t Option 2j Option 2k tion 2n (2N)***
Output 0 V to 5 V ±5 V 0 V to 5 V or ±5 0 V to 10 V or 4 mA to 20 mA 4 mA to 20 mA 4 mA to 20 mA
signal V @ 45 mA ±10 V @ 45 mA
Input power ±15 V or 26 Vdc ±15 V or 26 Vdc 18 Vdc to 28 15 Vdc to 28 22 Vdc to 32 9 Vdc to 32 Vdc 9 Vdc to
(voltage) to 32 Vdc to 32 Vdc Vdc Vdc Vdc 28 Vdc
Input power 45 mA 45 mA 40 mA 40 mA 65 mA 4 mA to 28 mA 4 mA to 24 mA
(current)
Freq. resp 3000 Hz 3000 Hz 3000 Hz 3000 Hz 2500 Hz 300 Hz 2000 Hz
(amp)
Power sup- 60 db 60 db 60 db 60 db 60 db 60 db 60 db
ply rej.
Operating -20 °F to 185 °F -20 °F to 185 °F -20 °F to 185 °F -20 °F to 185 °F 0 °F to 185 °F 0 °F to 185 °F -20 °F to 185 °F
temp.
Reverse Yes Yes Yes Yes Yes Yes Yes
voltage
protection
Short cir. Momentary Momentary Momentary Momentary Yes Yes Yes
protection
Wiring A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply
code: B (-)Output/supply B (-)Output/supply B Output com- B (-) output B Output com- B No connection B No connection
connector C (-)Supply C (-)Supply mon** C Supply return mon** C No connection C No connection
(std) D (+) Output D (+) Output C Supply return ** D (+) Output C Supply return** D (+) Output D (+) Output
E Shunt cal 1 E Shunt cal 1 D (+) Output E Shunt cal 1 D (+) Output E Case ground E Case ground
F Shunt cal 2 F Shunt cal 2 E Shunt cal 1 F Shunt cal 2 E Shunt cal 1 F No connection F No connection
F Shunt cal 2 F Shunt cal 2
Wiring R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
code: Br (-) Supply Br (-) Supply Bl Output com- Bl Supply return Bl Output com- Bl (+) Output Bl (+) Output
cable4,5,6 O (-)Output/supply O (-)Output/supply mon* G (+) Output mon* W Case ground W Case ground
G (+) Output G (+) Output G Supply return* W (+) Output G Supply return*
B Shunt cal 1 B Shunt cal 1 W (+) Output B Shunt cal 1 W (+) Output
Y Shunt cal 2 Y Shunt cal 2 B Shunt cal 1 Br Shunt cal 2 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model MPB
OPTION CODES NOTES
Many range/option combinations are available in 1. For standard configuration with spherical radius, a hardened
our quick-ship and fast-track manufacture pro- surface is recommended to maintain the best loading conditions.
grams. Please see http://sensing.honeywell.com/ RC42 is recommended minimum hardness. Bearing lubricant at
TMsensor-ship for updated listings. loading interface recommended for maximum life.
2. Accuracies stated are expected for best-fit, straight-line for all er-
Load ranges 1, 2.5, 5, 10, 25, 50, 100, 250, 500, 1000 ton
rors including linearity, hysteresis and non-repeatability thru zero.
Temperature 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F10 3. Allowable maximum loads – Maximum load to be applied without
compensa- 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F10 damage.4
tion 1c. 0 °F to 185 °F 1i. -65 °F to 250 °F10 4. Without damage – loading to this level will not cause excessive
1d. -20 °F to 130 °F 1j. 0 °C to 50 °C zero shift or performance degradation. The user must consider
fatigue life for long term use and structural integrity. All structur-
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
ally critical applications (overhead loading, etc.) should always be
1f. 70 °F to 250 °F 1m. -25 °C to 110 °C designed with safety redundant load paths.
Internal 2a. Four-wire, 0 Vdc to 5 2n (2N) 4 mA to 20 mA 5. Special wiring code.
amplifiers6, 7 Vdc output (two-wire) intrinsically 6. Not available with option 1e, 1f, 1g, 1h, or 1i.
2c. 0 Vdc to 5 Vdc safe11 7. Amplifier option not available with low ranges. Consult factory.
8. Consult factory for TEDS availability with amplified models.
2j. 4 mA to 20 mA (three- 2t. 0 Vdc to 10 Vdc
9. This unit calibrated to Imperial (non-Metric) units.
wire) output output 10. Non-amplified only.
2k. 4 mA to 20 mA (two- 2u. Unamplified, mV/V 11. 5000 ohm bridge required.
wire)11 output
Electrical 6a. Bendix PTIH-10-6P 6g. Integral cable:
termination (or equivalent), 6-pin Neoprene (0 °F to
(max. 250 °F) 180 °F)6
6b. MS3102E-14S-6P 6i. Integral underwater
connector (10 ton to cable (max. 180 °F)6
1000 ton range)5 6j. 1/2-14 conduit fitting
6e. Integral cable: Teflon 6q. Integral cable: Poly-
(1 ton to 5 ton range) urethane
6f. Integral cable: PVC 6v. Phoenix connector
(-20 °F to 160 °F) on end of cable
Electrical 15a. Horizontal electrical exit port orientation
connector 15b. Vertical electrical exit port orientation
orientation 15c. Radial electrical exit port orientation
Shunt cali- 8a. Precision internal resistor (max. 250 °F)10
bration
Bridge type 11a. Square bridge10
11b. Symmetrical bridge10
11c. Square and symmetrical bridge10
31a. Dual bridge
Bridge resist- 12b. 5000 ohm (foil) (max. 250 °F)
ance
Special cali- 30a. Positive in compression, compression testing
bration only
9a. 10 point (5 up/5 down) 20 % increments @ 70 °F
9b. 20 point (10 up/10 down) 10 % increments @
70 °F
9c. ASTM E-74 calibration
9e. CE mark
30c. Negative in compression, compression testing
only
Shock and 44a. Shock and vibration resistance
vibration
Interfaces 53e. Signature calibration5
53t. TEDS IEEE 1451.4 module8
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model MPB High Capacity Compact Compression Load Cell
MOUNTING DIMENSIONS
Capaci- D0 mm [in] D1 mm [in] D2 mm [in] L1 mm [in] L2 mm [in] L3 mm [in] H mm [in] Thread Optional
ty (tons) lifting eye bottom
(v.s.) thread
1 6,6 [0.26] 22,1 [0.87] 9,4 [0.37] 19,05 [0.75] 0,51 [0.02] 1,52 [0.06] 9,53 [0.375] NA 8-32 UNC x
0.18 in deep
2.5 6,6 [0.26] 22,1 [0.87] 9,4 [0.37] 19,05 [0.75] 0,51 [0.02] 1,52 [0.06] 9,53 [0.375] NA 8-32 UNC x
0.18 in deep
5 10,41 [0.41] 24,89 [0.98] 13,46 [0.53] 22,35 [0.88] 1,02 [0.04] 1,52 [0.06] 9,53 [0.375] NA 8-32 UNC x
0.18 in deep
10 19,05 [0.75] 37,85 [1.49] 19,05 [0.75] 28,45 [1.12] 1,52 [0.06] 4,06 [0.16] 9,53 [0.375] NA 1/4-28 UNF x
0.25 in deep
25 29,97 [1.18] 49,78 [1.96] 29,97 [1.18] 44,96 [1.77] 3,05 [0.12] 7,62 [0.30] 19,05 [0.75] NA 1/4-28 UNF x
0.25 in deep
50 40,39 [1.59] 61,98 [2.44] 40,39 [1.59] 64,0 [2.52] 4,57 [0.18] 4,83 [0.19] 38,1 [1.5] NA 3/8-24 UNF x
0.38 in deep
100 57,15 [2.25] 81,03 [3.19] 57,15 [2.25] 85,85 [3.38] 6,35 [0.25] 17,53 [0.69] 38,1 [1.5] NA 3/8-24 UNF x
0.38 in deep
250 90,68 [3.57] 112,78 [4.44] 90,68 [3.57] 135,89 [5.35] 6,35 [0.25] 43,18 [1.7] 38,1 [1.5] 1/4-28 3/4-16 UNF x
0.75 in deep
500 128,27 [5.05] 163,58 [6.44] 128,27 [5.05] 192,28 [7.57] 6,35 [0.25] 66,04 [2.6] 38,1 [1.5] 1/4-28 3/4-16 UNF x
0.75 in deep
1000 181,36 [7.14] 214,38 [8.44] 181,36 [7.14] 264,41 6,35 [0.25] 101,6 [4.0] 38,1 [1.5] 3/8-16 1-12 UNF x
[10.41] 1.0 in deep
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model D
Thru-Hole Load Cell
DESCRIPTION
The Model D Donut Shaped Load Cell features a smooth thru- scale non-linearity and hysteresis of ±0.5 % F.S., respectively.
hole design often ideal for applications which require the load These models are used in compression applications and
structure to pass directly through the cell. Such applications are available in multiple hole and frame sizes. For optimum
include bolt force measurements, clamping forces, and performance, these cells must be mounted between load
monitoring overloads. Load ranges as low as 150 grams and as surfaces which are flat and parallel. The Model D miniature load
great as 30,000 pounds can be measured within a maximum full cell is designed to have a minimum thickness.
FEATURES
• 150 g to 30000 lb
• Thru-hole design
• Flexible configuration
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model D
MOUNTING DIMENSIONS
Ranges Order code ØOD mm ØID mm [in] H1 mm [in] H2 mm [in] H3 mm [in] ØD1 mm ØD2 mm
[in] [in] [in]
150, 250, BL912 12,7 [0.50] 2,54 [0.10] 3,81 [0.15] 0,51 [0.02] 0,25 5,08 [0.20] 11,43 [0.45]
500, 1000 g [0.01]
5, 10 lb BL912 25,4 [1.00] 5,08 [0.20] 7,11 [0.28] 0,76 [0.03] 0,51 [0.02] 6,60 [0.26] 21,59 [0.85]
25, 50, 100 BL912 25,4 [1.00] 5,08 [0.20] 7,11 [0.28] 0,76 [0.03] 0,51 [0.02] 9,14 [0.36] 21,59 [0.85]
lb
Frame A BL913 38,1 [1.50] See below 12,7 [0.50] 1,27 [0.05] 0,76 [0.03] 12,7 [0.50] 30,73 [1.21]
(100 to 2000
lb)
Frame B BL914 50,8 [2.00] See below 16,00 [0.63] 1,52 [0.06] 0,76 [0.03] 22,53 42,67 [1.68]
(250 to [0.88]
10000 lb)
Frame C BL915 76,2 [3.00] See below 25,4 [1.0] 2,03 [0.08] 0,76 [0.03] 43,18 [1.70] 62,48 [2.46]
(2000 to
30000 lb)
Listed above are four different order codes; BL912, BL913, BL914, BL915. The frame size selection guide below indicates that with a single shell size
(outside diameter), different thru holes are available for order codes BL913, BL914 and BL915 (frames A, B, and C, respectively). To choose a product,
first select the desired load capacity. Then, if applicable, choose the desired inner diameter and an appropriate frame size. For example, a 250 lb load
cell is available in the small frame size (A) with a nominal thru hole size of 1/8 in (P), 3/16 in (Q), 1/4 in (R) or 3/8 in (S) diameter, or in the medium frame
size (B) with thru hole sizes up to 5/8 in (V). We manufacture the actual hole dimensions to provide some clearance; for example the 1/8 in (P) dimen-
sion, the actual dimension is 0.128 in.
Hole letters P Q R S T V W Y Z
ØID (nom) 1/8 in 3/16 in 1/4 in 3/8 in 1/2 in 5/8 in 3/4 in 1 in 1 1/4 in
ØID (act) 0.128 in 0.193 in 0.266 in 0.391 in 0.532 in 0.656 in 0.781 in 1.032 in 1.281 in
100 lb A A A A NA NA NA NA NA
250 lb A or B A or B A or B A or B B B NA NA NA
500 lb A or B A or B A or B A or B B B NA NA NA
1000 lb A or B A or B A or B B B B NA NA NA
2000 lb A, B, or C A, B, or C A, B, or C B or C B or C B or C C C C
3000 lb B or C B or C B or C B or C B or C C C C C
5000 lb B or C B or C B or C B or C B or C C C C C
7500 lb B or C B or C B or C B or C B or C C C C C
10000 lb B or C B or C B or C B or C B or C C C C C
15000 lb C C C C C C C C C
20000 lb C C C C C C C C C
30000 lb C C C C C C C C C
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model TH
Thru-Hole Load Cell
DESCRIPTION
Model TH Donut Shaped Load Cell features a smooth thru- applications. For optimum performance, this load cell must be
hole design for use in applications which require the load mounted between load surfaces which are flat and parallel. The
structure to pass through the cell. Such applications include Model TH Donut Shaped Load Cell is designed to provide the
bolt force measurement, post or leg mount, and rolling mill customer with an internal hole diameter which is large relative
systems. Load ranges as low as 15,000 pounds and as great to the outside diameter. The Model TH is a small size, high
as 200,000 pounds can be measured within a maximum full capacity load cell.
scale non-linearity of ±0.25. This model is used in compression
FEATURES
• 15000 lb to 200000 lb range
• Thru-hole design
• Compact column construction
• mV/V output
• 0.25 % linearity
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model TH
ENVIRONMENTAL SPECIFICATIONS
DEFLECTIONS AND RINGING FREQUENCIES
Characteristic Measure
Temperature, operating -54 °C to 121 °C [-65 °F to 250 °F] Capacity (lb) Deflection at Ringing fre- Weight kg
full scale mm quency (kHz) [lb]
Temperature, compensated 15 °C to 71 °C [60 °F to 160 °F] [in]
Temperature effect, zero 0.005 % full scale/°F 15000 0,025 [0.001] 35 0,18 [0.4]
Temperature effect, span 0.005 % full scale/°F 20000 0,025 [0.001] 35 0,18 [0.4]
30000 0,051 [0.002] 17 0,45 [1.0]
50000 0,051 [0.002] 17 0,45 [1.0]
ELECTRICAL SPECIFICATIONS
75000 0,076 [0.003] 14 0,90 [2.0]
Characteristic Measure
100000 0,076 [0.003] 14 0,90 [2.0]
Strain gage type Bonded foil
150000 0,152 [0.006] 12 1,13 [2.5]
Excitation (calibration) 10 Vdc
200000 0,102 [0.004] 10 2,72 [6]
Insulation resistance 5,000 mOhm @ 50 Vdc
Bridge resistance 350 ohm
Zero balance ±1 % full scale
Electrical termination (std) Teflon cable (5 ft)
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 150 % FS1
Weight See table
Case material Stainless steel
Deflection full scale See table
Natural frequency See table
WIRING CODES
Cable Unamplified
Red (+) excitation
Black (-) excitation
Green (-) output
White (+) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Thru-Hole Load Cell
MOUNTING DIMENSIONS
Ranges (lb) H mm [in] OD mm [in] ID mm [in] D2 mm [in] D3 mm [in]
15000, 20000 38,1 [1.50] 38,1 [1.50] 19,3 [0.76] 26,92 [1.06] 29,21 [1.15]
30000, 50000 50,8 [ [2.00] 50,8 [ [2.00] 25,65 [1.01] 38,1 [1.50] 38,1 [1.50]
75000, 100000 63,5 [2.50] 63,5 [2.50] 32,60 [1.26] 47,75 [1.88] 47,75 [1.88]
150000 76,2 [3.00] 76,2 [3.00] 38,35 [1.51] 58,67 [2.31] 61,97 [2.44]
200000 88,9 [3.50] 88,9 [3.50] 44,70 [1.76] 69,85 [2.75] 88,9 [3.50]
OPTION CODES
Many range/option combinations are available in
our quick-ship and fast-track manufacture pro-
grams. Please see http://sensing.honeywell.com/
TMsensor-ship for updated listings.
Load ranges 15K, 20K, 30K, 50K, 75K, 100K, 150K, 200K
Temperature 1a. 60 °F to 160 °F 1g. 70 °F to 325 °F
compensa- 1b. 30 °F to 130 °F 1h. 70 °F to 400 °F
tion 1c. 0 °F to 185 °F 1i. -65 °F to 250 °F
1d. -20 °F to 130 °F 1j. 0 °C to 50 °C
1e. -20 °F to 200 °F 1k. -20 °C to 85 °C
1f. 70 °F to 250 °F 1m. -25 °C to 110 °C
Internal am- 2u. Unamplified, mV/V output
plifiers
Electrical 6a. Bendix PTIH-10-6P 6h. Integral cable:
termination (or equivalent), 6-pin Silicone
(max. 250 °F) 6i. Integral underwater
6b. MS connector cable
MS3102E-14S- 6j. 1/2-14 conduit fitting
6P (mates with with 5 ft of 4 conduc-
MS3106E-14S-6S) tor PVC cable
(max. 160 °F)4 6q. Integral cable: Poly-
6e. Integral cable: Teflon urethane
(5 ft range) 6v. Phoenix connector
6f. Integral cable: PVC on end of cable
6g. Integral cable: Neo- 15d. Connector on end
prene of cable
Shunt 8a. Precision internal resistor
calibration
Special 9a. 10 point (5 up/5 down) 20 % increments @ 70 °F
calibration 9b. 20 point (10 up/10 down) 10 % increments
@ 70 °F
9c. ASTM E-74 calibration
30a. Positive in compression, compression testing
only
30c. Negative in compression, compression testing
only
Bridge type 31a. Dual bridge
Bridge 12b. 5000 ohm (foil)
resistance
Electrical 15a. Horizontal electrical exit port orientation
connector 15b. Vertical electrical exit port orientation
orientation 15c. Radial electrical exit port orientation
15d. Connector on end of cable
Shock and 44a. Shock and vibration resistance
vibration
Interfaces 53e. Signature calibration
53t. TEDS IEEE 1451.4 module
Honeywell • Sensing and Control 3
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model TH Thru-Hole Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Allowable maximum loads – maximum load to be applied without
damage.2 Honeywell’s standard product warranty applies unless agreed
2. Without damage - loading to this level will not cause excessive zero to otherwise by Honeywell in writing; please refer to your
shift or performance degradation. The user must consider fatigue
life for long-term use and structural integrity. All structurally critical order acknowledgement or consult your local sales office for
applications (overhead loading, etc.) should always be designed specific warranty details. If warranted goods are returned to
with safety redundant load paths.
Honeywell during the period of coverage, Honeywell will repair
3. This unit calibrated to Imperial (non-Metric) units.
4. Cannot be used with options 1c, 1e, 1f, 1g, 1h, or 1i. or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
TYPICAL SYSTEM DIAGRAM of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3719
Bolt and Engine Mount Force Sensor
DESCRIPTION
The bolt force sensor is a unique transducer which is essentially The beveled hole in this washer, which always faces away from
a hollow-compression strain gage load cell. It is designed to be the sensor, provides clearance for the bolt head radius. When
used with most strain gage indicators. The bolt force sensor is a torque wrench is used, a torque vs. clamp force curve can be
a three-piece assembly consisting of: 1. a large hardened and generated. The 3719 bolt force sensor is designed for use in
ground flat washer with one side beveled, 2. the sensor, and 3. a fastener testing where the compression loading of the sensor
small hardened and ground washer. is induced by the tensile loading of the fastener. The bolt force
sensor must be used with the size fastener for which it was
The three pieces are assembled for various applications. The
designed.
large washer isolates the sensor from the force application tool.
FEATURES
• Compact
• High output
• Standard models for bolts size no. 6 thru 2 in and
up to 20 mm
• Sensor and washers - carpenter 440C stainless steel
• Sensitive to neither bolt nor nut-applied torque
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3719
PERFORMANCE SPECIFICATIONS TYPICAL SYSTEM DIAGRAM
Characteristic Measure
Load range 1
1200 lb to 300000 lb
Non-linearity - ranges up to
±3.0 % of rated output
25K lb (67K N)
Non-linearity - ranges 30K
±4.0 % of rated output
lb and up (102K N)
Hysteresis
±5.0 % of rated output
ranges up to 25K lb (67K N)
Hysteresis - ranges 30K lb
±7.0 % of rated output
and up (102K N)
Repeatability ±0.10 % of rated output
±2 mV/V to 3.5 mV/V depending on size
Output @ rated capacity
(nominal)
Resolution Infinite
Standard calibration Compression
ENVIRONMENTAL SPECIFICATIONS
Characteristic Measure
Temperature, operating -54 °C to 93 °C [-65 °F to 200 °F]
Temperature, compensated 21 °C to 77 °C [70 °F to 170 °F]
Temperature effect, zero ±0.01 % of full scale/°F
ranges up to 12K lb
Temperature effect, zero ±0.007 % of full scale/°F
ranges 18K lb and up
Temperature effect, output ±0.02 % of reading/°F
ranges up to 12K lb
Temperature effect, output ±0.0035 % of reading/°F
ranges 18K lb and up
ELECTRICAL SPECIFICATIONS
Characteristic Measure
Excitation (maximum) 10 Vdc or Vac RMS
Insulation resistance, > 5000 mOhm @ 50 Vdc
bridge case
Bridge resistance 350 ohm
(tolerance)
Number of bridges 1
Zero balance ±1.0
MECHANICAL SPECIFICATIONS
Characteristic Measure
Static overload capacity 150 % of nominal capacity
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3663
Pedal Pressure Load Cell
DESCRIPTION
The pedal pressure sensor mounts directly to the brake pedal force measurements by the automotive industry, finds many
with its own mounting clamp. Load applied up to 1/2 inch off production applications. It adapts to any of the pedal or bar
center, produces less than a 0.5% error. Standard capacity operated devices used in all production facilities.
is 300 lbs. This load cell, which is used for brake pedal
FEATURES
• 50 lb, 100 lb, 200 lb, and 300 lb load capacity
• Low off-center loading error
• Easy mounting
• Rugged load surface
• Integral cable
• Compact size
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3663
2.0 DIA.
Honeywell
MECHANICAL SPECIFICATIONS In-Line Amplifier
Output Input
Serial Number
Characteristic Measure
Static overload capacity 150 % of nominal capacity Display Units
Safe overload rating 150 % of nominal capacity SC500 SC1000 SC2000
SC2001 SC3004
GM NK HH
7541 7558 7561-PSD
MODEL 3663
2003.1 lb.
L1 L2 L3 L4
VALUE CLEAR CHAN TARE
UP DOWN SETUP ENTER EXIT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3663 Pedal Pressure Load Cell
Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3419
Seat Belt Load Cell
DESCRIPTION
The seat belt sensor’s design and calibration method essentially
make it independent of belt thickness, which may change under
load. It provides excellent repeatability without the need for the
extensive belt wrap.
FEATURES
• Up to .1 in of belt thickness
• Small size
• Installs without “threading”
• Low sensitivity to belt thickness change
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 3419
Display Units
MECHANICAL SPECIFICATIONS
SC500 SC1000 SC2000
Characteristic Measure SC2001 SC3004
Static overload capacity 150 % of nominal capacity GM NK HH
MODEL 3419 7541 7558 7561-PSD
Weight 8 oz
Band thickness 2,54 mm [0.10 in]
2003.1 lb.
Band width 50,8 mm [2.0 in] L1 L2 L3 L4
VALUE CLEAR CHAN TARE
UP DOWN SETUP ENTER EXIT
RANGE CODES
Mating Connectors & Cables
Wire
023-LW181-023-LF Mating Connector
Red (+) excitation 7205-76-XX* Mating connector & 6 conductor cable
(unamplified unit with sense leads but not shunt cal)
Black (-) excitation 7205-75-XX** Mating connector & 4 conductor cable
(unamplified unit without sense leads but not shunt cal)
Green (+) output 7205-83-XX* Mating connector & 6 conductor cable
(for connection to instrument 7541)
White (-) output 7205-82-XX** Mating connector & 4 conductor cable
(for connection to instrument 7541)
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Models 3419 Seat Belt Load Cell
Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 6443
X-Y Force Sensor
DESCRIPTION
The X-Y force sensor is constructed of two strain gage bridges, strength and to minimize crosstalk between the two transducers.
mounted at 90º, isolated by a flexure system. The complete This unique sensor has excellent linearity characteristics and
two-component system, including flexures, is machined from maximum structure life.
one specially prepared metal billet to provide unusual structure
FEATURES
• Compact size
• 0.1 % linearity and hysteresis, respectively
• Simultaneous dual-axis readings
• Minimal crosstalk
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model 6443
MECHANICAL SPECIFICATIONS
Mating Connectors & Cables
Characteristic Measure
064-LW13621 Mating connector
Safe overload capacity 150 % of rated capacity
7200-76-XX* Mating connector and six conductor cable
Material Carbon steel (unamplified unit with sense leads but not shunt cal)
7200-75-XX** Mating connector (MS - 5 pin) and four conductor cable
(unamplified sensor without sense leads)
RANGE CODES 7200-111-XX** Mating connector ( MS – 5 pin ) & 6 conductor cable
for connection to 7541
Wire 7200-110-XX** Mating connector ( MS – 5 pin ) & 4 conductor cable
for connection to 7541
Red (+) excitation
* XX represents length in feet 100ft maximum
Black (-) excitation ** XX represents length in feet 20ft maximum
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Models 6443 X-Y Force Sensor
NOTES Warranty. Honeywell warrants goods of its manufacture as
1. Standard calibration for tension/compression load cells is in ten- being free of defective materials and faulty workmanship.
sion only.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model MBH
Minigram Beam Load Cell
DESCRIPTION
Models MBH Minigram Beam Load Cells are engineered to dimensions allow easy unit integration into existing systems.
measure very low bending forces and still achieve an impressive Model MBH uses foil gages and is available for load ranges from
0.1% full scale non-linearity and hysteresis. Built-in overload 150 grams to 10 pounds.
stops are incorporated to provide additional reliability. Miniature
FEATURES
• 150 g to 10 lb range
• Miniature size
• 0.1 % linearity
• Small diameter
• Integral cable
• Calibrated in compression only
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model MBH
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 400 % full scale or 20 lb, whichever is
less2
Weight 50 g
Material Aluminum
WIRING CODES
Cable Unamplified
Red (+) excitation
Black (-) excitation
Green (-) output
White (+) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model MBH Minigram Beam Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Positive in compression; calibrated in compression only.
2. Allowable maximum loads – maximum load to be applied without Honeywell’s standard product warranty applies unless agreed
damage.3 to otherwise by Honeywell in writing; please refer to your
3. Without damage - loading to this level will not cause excessive zero
shift or performance degradation. The user must consider fatigue order acknowledgement or consult your local sales office for
life for long term use and structural integrity. All structurally critical specific warranty details. If warranted goods are returned to
applications (overhead loading, etc.) should always be designed
Honeywell during the period of coverage, Honeywell will repair
with safety redundant load paths.
4. This unit calibrated to Imperial (non-Metric) units. or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
TYPICAL SYSTEM DIAGRAM of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model MBL
Minigram Beam Load Cell
DESCRIPTION
Models MBL Minigram Beam Load Cells are engineered to dimensions allow easy unit integration into existing systems.
measure very low bending forces and still achieve an impressive Model MBL uses semiconductor gages and is available for load
0.1 % full scale non-linearity and hysteresis. Built-in overload ranges from 25 to 1000 grams.
stops are incorporated to provide additional reliability. Miniature
FEATURES
• 25 g to 1000 g
• Miniature size
• 0.1 % linearity
• Small diameter
• Integral cable
• Calibrated in compression only
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model MBL
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 400 % FS2
Weight 50 g
Material Aluminum
WIRING CODES
Cable Unamplified
Red (+) excitation
Black (-) excitation
Green (-) output
White (+) output
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model MBL Minigram Beam Load Cell
NOTES Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
1. Positive in compression; calibrated in compression only.
2. Allowable maximum loads – maximum load to be applied without Honeywell’s standard product warranty applies unless agreed
damage.3 to otherwise by Honeywell in writing; please refer to your
3. Without damage - loading to this level will not cause excessive zero
shift or performance degradation. The user must consider fatigue order acknowledgement or consult your local sales office for
life for long term use and structural integrity. All structurally critical specific warranty details. If warranted goods are returned to
applications (overhead loading, etc.) should always be designed
Honeywell during the period of coverage, Honeywell will repair
with safety redundant load paths.
4. This unit calibrated to Imperial (non-Metric) units. or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
TYPICAL SYSTEM DIAGRAM of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model LP
Force Sensing Clevis Pin
DESCRIPTION
Model LP load pins are designed to be installed where pins or less steel construction and is available with a standard PTIH-10-
bolts are carrying a load. Applications which involve the use of 6P connector or an optional submersible cable. These
shackle pins, clevis pins and pully shafts are prime examples of rugged clevis pins provide excellent long term stability and reli-
where force sensing clevis pins can provide accurate, real time able operation under severe operating conditions.
monitoring of load forces. The Model LP features welded stain-
FEATURES
• 2000 lb to 200000 lb range
• Up to 1 % accuracy
• All welded stainless steel construction
• Amplified output available
• Intrinsically safe available (2N option only)8
• CE approved9
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Model LP
ELECTRICAL SPECIFICATIONS
Characteristic Measure
Strain gage type Foil
Excitation (calibration) 10 Vdc
Bridge resistance 5000 ohm
Electrical termination (std) PTIH-10-6P
Mating connector (not incl.) PT06A-10-6S or equivalent (AA111)
MECHANICAL SPECIFICATIONS
Characteristic Measure
Maximum allowable load 200 % FS1
Case material 17-4 PH stainless steel
WIRING CODES
Connector Unamplified (Std.)
A (+) excitation
B (+) excitation
C (-) excitation
D (-) excitation
E (-) output
F (+) output
INTERNAL AMPLIFIERS
Current two- Intrinsically
Amplifier Voltage out- Voltage out- Voltage out- Current three-
wire: Option safe amp: Op-
specifications put: Option 2a put: Option 2c put: Option 2t wire: Option 2j
2k tion 2n (2N)***
Output signal 0 V to 5 V 0 V to 5 V or ±5 V 0 V to 10 V or 4 mA to 20 mA 4 mA to 20 mA 4 mA to 20 mA
@ 45 mA ±10 V @ 45 mA
Input power (voltage) ±15 V or 26 Vdc 11 Vdc to 28 Vdc 15 Vdc to 28 Vdc 22 Vdc to 32 Vdc 15 Vdc to 9 Vdc to
to 32 Vdc 40 Vdc 28 Vdc
Input power (current) 45 mA 40 mA 40 mA 65 mA 4 mA to 28 mA 4 mA to 24 mA
Freq. resp (amp) 3000 Hz 3000 Hz 3000 Hz 2500 Hz 300 Hz 2000 Hz
Power supply rej. 60 db 60 db 60 db 60 db 60 db 60 db
Operating temp. -20 °F to 185 °F -20 °F to 185 °F -20 °F to 185 °F 0 °F to 185 °F 0 °F to 185 °F -20 °F to 185 °F
Reverse voltage protec- Yes Yes Yes Yes Yes Yes
tion
Short cir. protection Momentary Momentary Momentary Yes Yes Yes
Wiring code: connector A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply A (+) Supply
(std)4 B Output common B Output common** B Output common** B Output common** B No connection B No connection
C Supply return C Supply return ** C Supply return** C Supply return** C No connection C No connection
D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output D (+) Output
E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Shunt cal 1 E Case ground E Case ground
F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F Shunt cal 2 F No connection F No connection
Wiring code: cable4,5,6 R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply R (+) Supply
Bl Output common Bl Output common* Bl Output common* Bl Output common* Bl (+) Output Bl (+) Output
G Supply return G Supply return* G Supply return* G Supply return* W Case ground W Case ground
W (+) Output W (+) Output W (+) Output W (+) Output
B Shunt cal 1 B Shunt cal 1 B Shunt cal 1 B Shunt cal 1
Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2 Br Shunt cal 2
* Black and green wires are internally connected.
** Pins B and C are internally connected.
*** See our Web site for the most up-to-date information regarding intrinsically safe approvals, ref. #008-0547-00.
MOUNTING DIMENSIONS
Capac- A mm [in]** B mm [in] C mm [in] D mm [in] F mm [in] G mm [in] H mm [in] J mm [in] Key mm [in]
ity lb
50000 50,8 [2.000] 25,4 [1.00] 50,8 [2.00] 38,1 [1.50] 167,89 [6.61] 19,05 [0.75] 6,76 [0.266] 9,65 [0.38] 7,14 [0.281]
75000 63,5 [2.500] 31,75 [1.25] 63,5 [2.50] 50,8 [2.00] 193,29 [7.61] 19,05 [0.75] 6,76 [0.266] 12,7 [0.50] 7,14 [0.281]
100000 69,85 [2.750] 37,34 [1.47] 69,85 [2.69] 50,8 [2.00] 219,20 [8.63] 25,4 [1.00] 10,31 [0.406] 12,7 [0.50] 10,31 [0.406]
125000 76,2 [3.000] 36,58 [1.44] 76,2 [3.00] 50,8 [2.00] 225,55 [8.88] 25,4 [1.00] 10,31 [0.406] 16 [0.63] 10,31 [0.406]
150000 88,9 [3.500] 44,45 [1.75] 88,9 [3.50] 50,8 [2.00] 263,65 [10.38] 31,75 [1.25] 13,49 [0.531] 16 [0.63] 13,49 [0.531]
200000 101,6 [4.000] 57,15 [2.25] 101,6 [4.00] 50,8 [2.00] 301,75 [11.88] 31,75 [1.25] 13,49 [0.531] 19,05 [0.75] 13,49 [0.531]
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this catalogue is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com