Escolar Documentos
Profissional Documentos
Cultura Documentos
: UT-102
z OPERATION MANUAL z
AL-2
AL-1
AL-4
AL-3
UNIVERSAL INDICATOR/CONTROLLER
z CONTENTS z
F INTRODUCTION
F FRONT PANEL DESCRIPTION 1
F TECHNICAL SPECIFICATION 2
F INSTALLATION 3
F TERMINAL ARRANGEMENT 3
F PROGRAMMING FLOW CHART 4
F OPERATION 5
F ERROR MESSAGE AND TROUBLESHOOTING 8
F PANEL CUTOUT 9
F REGISTER ADDRESS FOR MODBUS 9
F CALIBRATION VALUES 9
z INTRODUCTION z
Unitech Instrument’s Universal Indicator is designed to
accept thermo-couple or RTD or Linear Input and displays the
process parameter through a 4 Digit Red LED Display.
AL 1 0083 AL 2
4
5
0083
6
AL 3 AL 4 7
8
M 9
10
11
SR NO DISPLAY DESCRIPTION
1 8888 PV Seven Segment LED display
2 PV Actual Process Value
3 SV Set Value
4 AL1 Red LED will glow on Relay 1 activation.
5 AL2 Red LED will glow on Relay 2 activation.
6 AL3 Red LED will glow on Relay 3 activation.
7 AL4 Red LED will glow on Relay 4 activation.
z TECHNICAL SPECIFICATION z
INPUT
TYPE RANGE TYPE RANGE
K-Type T/C -50 to 1200 ºC 4 to 20mA -1999 to 9999
J-Type T/C -50 to 750 ºC 0 to 20mA -1999 to 9999
R-Type T/C 0 to 1750 ºC 0.5 to 2.5V -1999 to 9999
S-Type T/C 0 to 1750 ºC 1 to 5V -1999 to 9999
T-Type T/C 0 to 400 ºC 0 to 10VDC -1999 to 9999
E-Type T/C -50 to 500 ºC SPECIAL -1999 to 9999
RTD PT-100 -50 to 400 ºC Cu 53 -50 to 250 ºC
Technical Specification
T/C
.. K, J, R, S, E, N, T
RTD
.. Pt100, Cu53 ( 2wire & 3 wire)
Currant .. 0 ~ 20mA dc , 4~20mA DC
Input Type
Voltage .. 0-5V/1-5V, 0.5 -2.5V/0- 10 V DC
Special on demand : 0-75/200 mV & 0-1/10V/100/300/V DC,0-75/
Input 200 mV 0-100/300V DC
.
Resistence . 0-500 Ω , 0-1/5/10 KΩ, 1MΩ
Transmitter power supply 24 V DC @ 30 mA max, isolated from I/p & O/P.
Cold junction comp. & Sensor break ind. Software base Automatic.
Range limits As per input range Table.
Accuracy + 0.1 % of span for Linear & RTD , + 0.25 % for T/C
Input impedance >330 KΩ for Voltage ,mV, and T/C, 100 Ω for current.
Indication 4 Digit 7 Segment display 0.56”
Indication
Status indication LEDs for Relay status & Communications
z INSTALLATION z
INPUT
OUTPUT 1 TEMP.(SELECTABLE) LINEAR 24 V DC
6 7 8 9
+ mA
+V
TPS
OUTPUT 2
+ 19 D 24 + COMMUNICATION
- 20 D 25 - (RS 485-232)
NC 21 UT-102 26 NC
RELAY-3 C 22 27 C RELAY-4
NO 23 28 NO
10 11 12 13 14 15 16 17 18
NO C NC NO C NC E N P
RELAY-2 RELAY-1 POWER SUPPLY
230/110V AC
z TERMINAL ARRANGEMENT z
POWER
POWER SELECTION POWER SUPPLY-AC POWER SUPPLY-DC
JUMPER SELECTION
FOR 230/110 VAC
16 17 18
16 17 18
TPS-
A
6 7
+ +
V TPS+
B T
DC +
mA
DC - mA +
B --
mA -
6-5 : mA DC
RTD PT-100 J/K/R/S/T/E 7-5 : V DC
OUTPUT
RELAY SSR RETRANSMITION RS - 484
NO
13
10
23
28
-
24 25
10 11
+ +
1 2
C 24 V
-485
OUTPUT
14
22
27
11
NC - +
15
12
21
26
Relay : 1 2 3 4
PRESS M KEY
-
MODE -
MODE -
MODE -
MODE
COnf setp CAL CPAS
PASS PASS PASS oPAS
0000 0000 0000 0000
1NP ZERO CALZ nPAS
PT-1 0000 ---- 8888 *
TSP1 span CALS
L oN 1000 ----
*Any New Password
TSP2 SP1 CALL
Password Protected
L oN 0300 STRT
dp Hys1 CALH
0001 0002 STRT
DEAD SP2 CALA
no 0500 0032
CTYP HYS2
LEAN 0002
oFFS N
TMS1
0005 0050
NOTE :
CA1n
V N
TMS2
0006 0050 Default Password will be 0000
Protected Parameter Password will be 1111
nadd oFST
Password Protected
Password Protected
0001 0000
baUd oP-L
9600 0000
Pr1T oP-H
nonE 1000
1. CONFIGURATION MODE
This Mode is used to change Input , Relay and Communication Operation
Configuration
CONFIGURATION MODE PARAMETER CONF
Parameter Description Range Default Value
ON
SV SV+Hyst
PV
H oN : Active in High
H ON : OFF
SV-Hyst
PV
SV
2. SETUP MODE
This Mode is used to Setting the instrument Parameter. To set zero span
value, alarm set points with hysteresis, offset etc.
SETUP MODE PARAMETER sETP
Parameter Description Range Default Value
Hys1 Hysteresis # 2
Values from 000.0 to 999.9 000.2
0002 Increase digit by key, decrease by key
3. CALIBRATION MODE
This Mode is used to Calibration of the Instrument.
CALIBRATION MODE PARAMETER CAL
Parameter Description Range Default Value
OPEn
-Sensor break error -Replace sensor
z PANEL CUTOUT z
AL1 AL2
AL3 AL4
PANEL CUTOUT
Model A B C D E
UT - 96 x 96 96 96 10 80 92 92 +0.5 92 +0.5 120 96
z CALIBRATION VALUES z
INPUT ZERO-VALUE SPAN VALUE
J - T/C 0100-0600 7400-7800
K - T/C 0800-1000 7400-7800
R - T/C 0800-1000 7400-7800
S - T/C 0800-1000 7400-7800
T - T/C 0800-1000 7400-7800
4 - 20 mA 0100-0600 7400-8000
0 - 20 mA 0100-1000 7400-8000
1 - 5 VDC 0100-1000 7000-8000
10 V DC 0100-1000 7000-8000
PT-100 900-1500 2000-3000 *
E - T/C 0800-1000 7000-8000
* Span Calibration at 100ºC
UNITECH
FLOW RATE-122.65
TOT- 12345678.25
SMART CLEAN ROOM INDICATOR
UNITECH
FLOW RATE-122.65
TOT- 12345678.25
AL-1
AL-2
AL-1 AL-2 AL-3 AL-4 COM
COM
t.com
-Www.unitechinstrumen CH-1 CH-1
CH-1
CH-2 CH-2
CH-2
CH-3 CH-3
CH-3
CH-4
CH-4 CH-4
TEMPRETURE+RH FLOW
Temp. Sensor and temp.2 wire transmitter Flow Metering Systems(volume / mass) Flow : Rate/Totlizer/Comuper/Batch
Single channel universal indicator controller
Dual channel universal indicator controller Orifice Flow Meter ((NG) gas / steam) Flow indi.& Cont. (4-20 mA & frequency)
Multy channel temp indicator(4,8,12,16,20) Steam Flow meter Flow indicator & Totalizers (universal-i/p)
PID and PROFILE controller Natural gas & standard gas Flow meter Batch indicator cum controller
Temp. Scanner with software (4,,8,12,16,20) Thermel Dispenser Air Flow Meter Natural Gas flow computer (as per AGA3)
data logger with pc software (4,8,12,16,20) Magnetic Flow Meter (water) - On line temp.& Pressure compensation)
Temp.+Rh transmitter (sensor) Ultrasonic Flow Meter Steam flow computer (saturated &superheated)
Temp.+Rh indicator cum controller Low cost ½”& 1” Air/Gas Flow meter - On line temp.& Pressure compensation)
Humidity sensor/ indicator/ controller SCADA software (Online and Offline Report / Trend / part lading ) for flow analysis
SCADA SOFTWARE CLEAN ROOM/HVAC /PHARMA
This software gives you access to real time process Temp. & pressure & vacuum & magnehelic gauge Diffrancial pressure swich and sensor
parameters in numeric and graphical form. It is a Temp.+humidity transmitter
pre-engineered software package that provides all PH sensor indicator(on line & table top )
benefits of on line data logging and trending, the Synchronized Digital Clocks / masters and slaves FLP temp indicator & contr.
software can interface with multiple scanners, FLP temp scanner and data loggers with software AHU control panel with SCADA
indicator.pid,plc,and data acquisitions systems using. Temp.+humidity indicator Controller. Conductivity sensor indicator
multidrop Rs485 communication. With the feature of
historical data logging function the entire precess history can be Temp.+RH +dp clean room indicator with sensor Control valve (on/off & modulating)
recorded for future analysis or validation. We can gives all instruments in SS or flame proof panels and box
LEVEL PRESSURE Isolator /convertor
High pressurizes tank level indication sys. Single/Dual channel indicator contr. Universal input Signal isolator & convertor & multiplexer
Differantial pressure type level indicator. Pressure & vacuum transmitter Multi channel Signal isolator & convertor & multiplexer
Ultrasonic level transmitter & controller Differantial Pressure transmitter Loop powered Signal isolator & square root extractors
Conductivity level transmitter & contr. Hi accurate digital pressure gauge. Equations computation modual & Linearization modual
Water Level Control systems. Loop power indicator (PT/DP) MV to mA AC V to mA
Convertor Load cell to mA
Level Switch/Sensor. I to P / E to P convertor. Ohms to mA/V Amp. to mA DC V to mA
Temprature Pressure Gas Procces value big indicator RPM/MPM indicator controller Vibration sensors indicators
Humidity Vacuum Proxi -Display size : 2”,4”,6”,8”,12” Alarm annunciator(2 to 200 chnl.) Gas starilizers control systems
Photo sensor Thayrister Ssr Clocks with date and years Auto manual station Bagging controller (cements)
Production monitoring systems Manual loaders & celebrators Control valves and positioners
We can provide GSM mobile comm. and modbus RTU 232/485 connectivity with pc software in our entire product range.
We provide SCADA software (Online and Offline Report / Trend / part lading ) for flow analysis and data logging systems.
We can provide our all instruments in MS or SS panel and also provide in flame proof and weather proof housing.
We can accept to make customized instruments & trucky systems (hardware and computer software) as per customers needs.
industrials procces automaton
Total solution provider for Industrials Automaton
PLC and HMI and hi speed communications module.
SCADA system (standard and customized computer software)
Servo Motors & Drives & AC drives / inverter
Unitech Instruments
503/504 Helix Complex.Opp-Surya Hotel,Sayajigunj,
Vadodra-390005,Gujarat ,India
Phone.: 0265-6623551/6553555/2361241 Fax.:265-6623551
E-mail :salse@unitechinstrument.com,kuntal_unitech@yahoo.com
URL :www.unitechinstrument.com, cell no :094273 01436