Escolar Documentos
Profissional Documentos
Cultura Documentos
5. Noise performance of conventional AM, when compared with that of suppressed carrier systems
is
a. Superior
b. Inferior
c. Same
d. Can t be compared
2
c. 2 Kf
2
d. Kf
d. 1
12. In PM, the power spectral density of the O/P noise, varies with frequency as
a. Parabola
b. Hyperbola
c. Uniform
d. circle
13. In order to realize an improvement in S/N ration in FM over AM, we must have the FM modulation
index greater than
a. 1/ v3
3
b. v
3
c. 2/v
3
d. v /2
14. For a modulation index β > 0.5 the noise performance of FM when compared to AM is
a. Better
b. Same
c. worst
d. Can't be compared
16. The transition point between NBFM and WBFM is for the value of modulation index
a. 0.5
b. 0.6
c. 0.4
d. 0.7
18. In FM, the power spectral density of the O/P noise, varies with frequency as
a. Parabola
b. Hyperbola
c. Uniform
d. circle
b. HPF
c. BPF
d. BEF
32. A Collector modulated transmitter has supply voltage of 12 Volts and collector current of 1 A. The
modulated power for 100 % modulation is
a. 6W
b. 12 W
c. 18W
d. 24W
33. While switching on the transmitter anode voltages should not be applied with out
a. Staff on duty
b. Charging feeder lines
c. switching on the cooling system
d. signal from studio
36. A device that reduces the gain of A. F. amplifier when the input exceeds predetermined value is
called
a. Peak clipper
b. Detector
c. echo suppressor
d. Discriminator
38. A class C amplifier has supply voltage of 12 V and collector current of 1A. Its efficiency is 80 %.
The RF output power is
a. 9.6W
b. 12W
c. 15W
d. 24W
39. The final carrier frequency of an amplitude modulated transmitter is obtained by the use of
a. Crystal Oscillator
b. L C Oscillator
c. Harmonic generators
d. Frequency dividers
42. In AM modulator circuits, the carrier and the modulating signal are
a. Multiplied
b. Added
c. Subtracted
d. Mixed
43. An AM transmitter shall produce 1KW of carrier power with 200V supply. The load seen by the
amplifier is
a. 5?
b. 10?
c. 20?
d. 40?
44. The frequency drift allowed for shoth wave and UHF transmitters is
a. +0.02%
b. -0.1 %
c. +0.05%
d. 0.002 %
46. A push pull power amplifier that is used for carrier suppression is called
a. Hormonic generator
b. Balanced modulator
c. Frequency multiplier
d. Frequency mixer
49. A PLL FM generator has Kf = 100 KHz/V and peak deviation of 75 KHz. The RMS modulating
voltage required is around
a. 0.25V
b. 0.5V
c. 0.75V
d. 1.3V
54. Straight receiver with only crystal detector and head phone will work
a. Any where
b. 10 Km from Tx
c. areas of local Tx
d. 50 Km from
56. The ability of a receiver to distinguish the wanted and unwanted signals is
a. Sensitivity
b. selectivity
c. S/N ratio
d. efficiency
59. The output from radio receiver varies abruptly many times with out notice. This is called
a. Hum
b. Motor boating
c. fading
d. noise
c. 4 places
d. doesnot
71. The following is not one of the common stage for AM & FM receivers
a. IF amplifier
b. limiter
c. ratio detector
d. mixe
72. Indicate which one of the following blocks is used in both communication receivers and broadcast
receivers
a. Squelch
b. beat frequency oscillator
c. mixer
d. Limiter
76. Superheterodyne receiver is tuned to a frequency 540 KHz, the IF is 455 KHz. The image signal is
a. 1295 KHz
b. 385 KHz
c. 1750 KHz
d. 420 KHz
78. Adjusting all the RF circuits to suit the calibrating of wave length frequency of dial is called
a. tuning
b. adjusting
c. tracking
d. misalignment
79. The local oscillator of a broadcast receiver is tuned to s frequency higher than the incoming
frequency
a. to allow adequate frequency coverage without switching
b. to allow the image frequency rejection
c. to permit easier tracking
d. otherwise intermediate frequency cannot be produced
81. The minimum channel band width required for transmitting 3 baseband signals, each is band
limited to 3 KHz
a. 6 KHz
b. 3 KHz
c. 9 KHz
d. 1.5 KH
82. A base band signal band limited to 5KHz is to be reconstructed from its samples. The minimum
pass bandwidth of the reconstruction filter should be
a. 10 KHz
b. 2.5 KHz
c. 5 KHz
d. 20 KHz
83. The circuit that reduces the gain of RF amplifiers when the input signal increases beyond a
predetermined value is
a. Crystal filter
b. differentiation
c. delayed AVC
d. Simple AVC
87. From the point of view, the main difference between tube and transistor receivers is that the
latter
a. require AGC power rather than the voltage
b. do not really need AGC because overloading causes limiting
c. have troubles because AGC is not very effective in them
d. must have IF stages even more stabilized than they are normally
92. The effect of delayed AGC is to increase the following characteristics of a receiver
a. Sensitivity
b. Selectivity
c. Image rejection
d. thresho
93. The following circuit in a receiver compensates for a wide range of input signal levels
a. Amplitude limiter
b. AGC
c. AFC
d. noise limiter
97. Indicate which one of the following frequencies in not usually used as IF
a. 10.7MHz
b. 455 KHz
c. 36 MHz
d. 26 MHz
102. AGC filter uses normally the values of R = 500 K and C equal to
a. 1µF
b. 2µF
c. 10µF
d. 20µF
103. The width (τ ) of a sample of a base band signal of band limited frequency fm can have a value
a. τ ? 1/ fm
b. τ ? 1/ fm
c. τ =1/ fm
d. τ ? 1/ fm
105. With correct three point tracking a maximum tracking error as low as _ _ _ _ _ _ _ is possible
a. 2.5 KHz
b. 4 KHZ
c. 3 KHz
d. 0.5 KH
c. local Oscillator
d. AF amplifier
114. To undo the distortion caused by the channel, which of the following can be used
a. Amplifier
b. Equalizer
c. Attenuator
d. Clamper