Escolar Documentos
Profissional Documentos
Cultura Documentos
10:52 PM
Project Name: Specific Title:
File Name: Mild Slab Date of Generation: Friday, April 5, 2019
TABLE OF CONTENT:
Concise Report
2 - Input Geometry
2.1 - Principal Span Data of Uniform Spans
2.7 - Support Width and Column Data
12 - Shear Reinforcement
12.1 - Shear Calculation Envelope
14 - Deflections
14.1 - Maximum Span Deflections
14.3 - Maximum Span Deflections
23 - Detailed Moments
24 - Detailed Shears
29 - Detailed Rebar
35 - Detailed Deflections
35.1 - Detailed Deflections
35.3 - Detailed Deflections
Graphical Reports
Deflection
Load Cases
Selfweight
Super Imposed Dead
Live
Other
Load Combinations
SERVICE_1_Max_LL
SERVICE_2_Max_LL
STRENGTH_1_Max_LL
Envelope
Legend
- Plan
- Elevation
- Live Load
Moment Diagrams
Project: "" / Load Case: Envelope
-7000
-6000
-5000
-4000
Moment [k-ft]
-3000
-2000
-1000
0
1000
2000
3000
4000
SPAN 1
DESIGN MOMENT
(Moment is drawn on tension side)
B.8 Deflection
Deflection Diagrams
File: Mild Slab
0.02
0.04
0.06
Deflection [in]
0.08
0.10
0.12
0.14
0.16
Span 1
DEFLECTION
B.9 Quantities
CONCRETE
Total volume of concrete = 4000.00ft3 (148.15 yd3)
Area covered = 3000.00 ft2
MILD STEEL
Total weight of rebar = 6608.76 lbs
Average rebar usage = 2.20 psf, 1.65 pcf
2 - INPUT GEOMETRY
NOTE: SELFWEIGHT INCLUSION REQUIRED (SW= SELF WEIGHT Computed from geometry
input and treated as dead loading. Unit selfweight W = 150.0 pcf
12 - SHEAR REINFORCEMENT
Note: "Ratio" is calculated using paired shear (V) and moment (M) design values resulting in the lowest
concrete capacity. For ACI and CSA codes, the lowest value of V*d/M is used.
Note: Sections with **** have exceeded the maximum allowable shear stress.
Note: Sections marked with xxxx have insufficient depth for shear design.
Note: Base stirrups flagged as OK satisfy the requirements - additional reinforcement is not needed. Base
stirrups flagged as NS are not sufficient - additional stirrups are reported in the table.
14 - DEFLECTIONS
Note: Deflections are calculated using effective moment of inertia of cracked sections.
23 - DETAILED MOMENTS
SPAN 1
X/L X SW SDL XL LL Min LL Max
ft k-ft k-ft k-ft k-ft k-ft
0.00 0.00 0.02 0.00 0.00 0.02 0.02
0.05 1.50 315.09 78.77 0.00 315.09 315.09
0.10 3.00 585.15 146.29 0.00 585.15 585.15
0.15 4.50 810.22 202.55 0.00 810.22 810.22
0.20 6.00 990.28 247.57 0.00 990.28 990.28
0.25 7.50 1125.30 281.34 0.00 1125.30 1125.30
0.30 9.00 1215.40 303.85 0.00 1215.40 1215.40
0.35 10.50 1260.50 315.12 0.00 1260.50 1260.50
0.40 12.00 1260.50 315.14 0.00 1260.50 1260.50
0.45 13.50 1215.60 303.90 0.00 1215.60 1215.60
0.50 15.00 1125.70 281.42 0.00 1125.70 1125.70
0.55 16.50 990.74 247.69 0.00 990.74 990.74
0.60 18.00 810.81 202.70 0.00 810.81 810.81
0.65 19.50 585.88 146.47 0.00 585.88 585.88
0.70 21.00 315.94 78.99 0.00 315.94 315.94
0.75 22.50 1.01 0.25 0.00 1.01 1.01
0.80 24.00 -358.93 -89.73 0.00 -358.93 -358.93
0.85 25.50 -763.86 -190.97 0.00 -763.86 -763.86
0.90 27.00 -1213.80 -303.45 0.00 -1213.80 -1213.80
0.95 28.50 -1708.70 -427.18 0.00 -1708.70 -1708.70
1.00 30.00 -2248.70 -562.17 0.00 -2248.70 -2248.70
24 - DETAILED SHEARS
SPAN 1
X/L X SW SDL XL LL Min LL Max
ft k k k k k
0.00 0.00 -225.04 -56.26 0.00 0.00 -225.04
0.05 1.50 -195.04 -48.76 0.00 0.00 -195.04
0.10 3.00 -165.04 -41.26 0.00 0.00 -165.04
0.15 4.50 -135.04 -33.76 0.00 0.00 -135.04
0.20 6.00 -105.04 -26.26 0.00 0.00 -105.04
0.25 7.50 -75.04 -18.76 0.00 0.00 -75.04
0.30 9.00 -45.04 -11.26 0.00 0.00 -45.04
0.35 10.50 -15.04 -3.76 0.00 0.00 -15.04
0.40 12.00 14.96 3.74 0.00 14.96 0.00
0.45 13.50 44.96 11.24 0.00 44.96 0.00
0.50 15.00 74.96 18.74 0.00 74.96 0.00
0.55 16.50 104.96 26.24 0.00 104.96 0.00
0.60 18.00 134.96 33.74 0.00 134.96 0.00
0.65 19.50 164.96 41.24 0.00 164.96 0.00
0.70 21.00 194.96 48.74 0.00 194.96 0.00
0.75 22.50 224.96 56.24 0.00 224.96 0.00
0.80 24.00 254.96 63.74 0.00 254.96 0.00
0.85 25.50 284.96 71.24 0.00 284.96 0.00
0.90 27.00 314.96 78.74 0.00 314.96 0.00
0.95 28.50 344.96 86.24 0.00 344.96 0.00
1.00 30.00 374.96 93.74 0.00 374.96 0.00
29 - DETAILED REBAR
SPAN 1
X/L X Analysis Top Analysis Minimum Minimum Selected Selected
Bot Top Bot Top Bot
ft in2 in2 in2 in2 in2 in2
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.05 1.50 0.00 15.56 0.00 0.00 0.00 15.56
0.10 3.00 0.00 28.85 0.00 0.00 0.00 28.85
0.15 4.50 0.00 40.28 0.00 0.00 0.00 40.28
0.20 6.00 0.00 49.48 0.00 0.00 0.00 49.48
0.25 7.50 0.00 56.50 0.00 0.00 0.00 56.50
0.30 9.00 0.00 60.73 0.00 0.00 0.00 60.73
0.35 10.50 0.00 63.57 0.00 0.00 0.00 63.57
0.40 12.00 0.00 63.57 0.00 0.00 0.00 63.57
0.45 13.50 0.00 60.73 0.00 0.00 0.00 60.73
0.50 15.00 0.00 56.50 0.00 0.00 0.00 56.50
0.55 16.50 0.00 49.48 0.00 0.00 0.00 49.48
0.60 18.00 0.00 40.28 0.00 0.00 0.00 40.28
0.65 19.50 0.00 28.85 0.00 0.00 0.00 28.85
0.70 21.00 0.00 15.56 0.00 0.00 0.00 15.56
0.75 22.50 0.00 0.05 0.00 0.00 0.00 0.05
0.80 24.00 17.69 0.00 0.00 0.00 17.69 0.00
0.85 25.50 38.33 0.00 0.00 0.00 38.33 0.00
0.90 27.00 60.73 0.00 0.00 0.00 60.73 0.00
0.95 28.50 86.99 0.00 0.00 0.00 86.99 0.00
1.00 30.00 115.57 0.00 0.00 0.00 115.57 0.00
Note: Reinforcement requirements for Initial condition are included in Service block. Reinforcement requirements for
UBC combination, if selected, are included in Analysis block.
SPAN 1
X/L X Demand Demand Moment Moment Demand/Cap Demand/Cap
Moment Pos Moment Neg Capacity Pos Capacity Neg acity Pos acity Neg
Note: Capacity is calculated with the rebar and PT required for the design, including user defined base reinforcement
35 - DETAILED DEFLECTIONS
SPAN 1
X/L X SW SW+SDL SW+SDL+Cr LL X Sustained Total
eep
ft in in in in in in in
0.00 0.0 0.000 0.000 0.000 0.000 0.000 0.000 0.000
0.05 1.5 0.014 0.017 0.017 0.013 0.000 0.031 0.031
0.10 3.0 0.027 0.034 0.034 0.026 0.000 0.060 0.060
0.15 4.5 0.039 0.049 0.049 0.038 0.000 0.087 0.087
0.20 6.0 0.050 0.062 0.062 0.048 0.000 0.111 0.111
0.25 7.5 0.059 0.073 0.073 0.057 0.000 0.130 0.130
0.30 9.0 0.065 0.082 0.082 0.063 0.000 0.145 0.145
0.35 10.5 0.070 0.087 0.087 0.067 0.000 0.155 0.155
0.40 12.0 0.072 0.090 0.090 0.069 0.000 0.159 0.159
0.45 13.5 0.072 0.090 0.090 0.068 0.000 0.158 0.158
0.50 15.0 0.070 0.087 0.087 0.066 0.000 0.153 0.153
0.55 16.5 0.065 0.081 0.081 0.061 0.000 0.142 0.142
0.60 18.0 0.059 0.073 0.073 0.054 0.000 0.127 0.127
0.65 19.5 0.051 0.064 0.064 0.046 0.000 0.109 0.109
0.70 21.0 0.042 0.052 0.052 0.036 0.000 0.089 0.089
0.75 22.5 0.033 0.041 0.041 0.027 0.000 0.067 0.067
0.80 24.0 0.023 0.029 0.029 0.017 0.000 0.046 0.046
0.85 25.5 0.014 0.018 0.018 0.008 0.000 0.025 0.025
0.90 27.0 0.007 0.009 0.009 0.000 0.000 0.009 0.009
0.95 28.5 0.002 0.002 0.002 -0.005 0.000 -0.002 -0.002
1.00 30.0 0.000 0.000 0.000 0.000 0.000 0.000 0.000
SPAN 1
X/L X SW SW+SDL SW+SDL+Cr LL X Sustained Total
eep
ft in in in in in in in
0.00 0.0 0.000 0.000 0.000 0.000 0.000 0.000 0.000
0.05 1.5 0.014 0.017 0.017 0.013 0.000 0.017 0.031
0.10 3.0 0.027 0.034 0.034 0.026 0.000 0.034 0.060
0.15 4.5 0.039 0.049 0.049 0.038 0.000 0.049 0.087
0.20 6.0 0.050 0.062 0.062 0.048 0.000 0.062 0.111
0.25 7.5 0.059 0.073 0.073 0.057 0.000 0.073 0.130
0.30 9.0 0.065 0.082 0.082 0.063 0.000 0.082 0.145
0.35 10.5 0.070 0.087 0.087 0.067 0.000 0.087 0.155
0.40 12.0 0.072 0.090 0.090 0.069 0.000 0.090 0.159
0.45 13.5 0.072 0.090 0.090 0.068 0.000 0.090 0.158
0.50 15.0 0.070 0.087 0.087 0.066 0.000 0.087 0.153
0.55 16.5 0.065 0.081 0.081 0.061 0.000 0.081 0.142
0.60 18.0 0.059 0.073 0.073 0.054 0.000 0.073 0.127
0.65 19.5 0.051 0.064 0.064 0.046 0.000 0.064 0.109
0.70 21.0 0.042 0.052 0.052 0.036 0.000 0.052 0.089
0.75 22.5 0.033 0.041 0.041 0.027 0.000 0.041 0.067
0.80 24.0 0.023 0.029 0.029 0.017 0.000 0.029 0.046
0.85 25.5 0.014 0.018 0.018 0.008 0.000 0.018 0.025
0.90 27.0 0.007 0.009 0.009 0.000 0.000 0.009 0.009
0.95 28.5 0.002 0.002 0.002 -0.005 0.000 0.002 -0.002
1.00 30.0 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Deflection Diagrams
File: Mild Slab
0.02
0.04
0.06
Deflection [in]
0.08
0.10
0.12
0.14
0.16
Span 1
DEFLECTION
LOAD CASE: Selfweight
350
-2000
300
-1500 250
200
-1000 150
Moment [k-ft]
Shear [k]
100
-500
50
0 0
-50
500 -100
-150
1000
-200
-250
Span 1 Span 1
MOMENT SHEAR
Deflection Diagrams
File: Mild Slab
0
0.01
0.02
0.03
Deflection [in]
0.04
0.05
0.06
0.07
Span 1
DEFLECTION
-500
80
-400
60
-300
40
-200
Moment [k-ft]
Shear [k]
20
-100
0 0
100 -20
200
-40
300
-60
Span 1 Span 1
MOMENT SHEAR
Deflection Diagrams
File: Mild Slab
0
0.002
0.004
0.006
0.008
Deflection [in]
0.010
0.012
0.014
0.016
0.018
Span 1
DEFLECTION
Live Load Min Live Load Max Live Load Min Live Load Max
400
350
-2000
300
-1500 250
200
-1000 150
Moment [k-ft]
Shear [k]
100
-500
50
0 0
-50
500 -100
-150
1000
-200
-250
Span 1 Span 1
MOMENT SHEAR
Deflection Diagrams
File: Mild Slab
0.01
0.02
Deflection [in]
0.03
0.04
0.05
0.06
0.07
Span 1
DEFLECTION
-1.0 1.0
-0.8 0.8
-0.6 0.6
-0.4 0.4
-0.2 0.2
Moment [k-ft]
Shear [k]
0 0
0.2 -0.2
0.4 -0.4
0.6 -0.6
0.8 -0.8
1.0 -1.0
Span 1 Span 1
MOMENT SHEAR
Deflection Diagrams
File: Mild Slab
-1.0
-0.8
-0.6
-0.4
-0.2
Deflection [in]
0.2
0.4
0.6
0.8
1.0
Span 1
DEFLECTION
Moment Diagrams
Project: "" / Load Case: SERVICE_1_Max_LL
+1.00 SW +1. 00 LL_Max +1.00 SDL +1. 00 XL +0.00 LAT
Moment Drawn on Tension Side
-5000
-4000
-3000
Moment [k-ft]
-2000
-1000
1000
2000
3000
SPAN 1
DESIGN MOMENT
(Moment is drawn on tension side)
Rebar Diagrams
Project: "" / Load Case: SERVICE_1_Max_LL
+1.00 SW +1. 00 LL_Max +1.00 SDL +1. 00 XL +0.00 LAT
Rebar Required Top Rebar Required Bottom Rebar Provided Top Rebar Provided Bottom
1.0
0.8
0.6
0.4
0.2
Rebar [in²]
-0.2
-0.4
-0.6
-0.8
-1.0
SPAN 1
REINFORCEMENT
REQUIRED AND PROVIDED
Moment Diagrams
Project: "" / Load Case: SERVICE_2_Max_LL
+1.00 SW +1. 00 LL_Max +1.00 SDL +1. 00 XL +0.00 LAT
Moment Drawn on Tension Side
-5000
-4000
-3000
Moment [k-ft]
-2000
-1000
1000
2000
3000
SPAN 1
DESIGN MOMENT
(Moment is drawn on tension side)
Rebar Diagrams
Project: "" / Load Case: SERVICE_2_Max_LL
+1.00 SW +1. 00 LL_Max +1.00 SDL +1. 00 XL +0.00 LAT
Rebar Required Top Rebar Required Bottom Rebar Provided Top Rebar Provided Bottom
1.0
0.8
0.6
0.4
0.2
Rebar [in²]
-0.2
-0.4
-0.6
-0.8
-1.0
SPAN 1
REINFORCEMENT
REQUIRED AND PROVIDED
Moment Diagrams
Project: "" / Load Case: STRENGTH_1_Max_LL
+1.20 SW +1. 60 LL_Max +1.20 SDL +1. 60 XL +0.00 LAT
Moment Drawn on Tension Side
-7000
-6000
-5000
-4000
-3000
Moment [k-ft]
-2000
-1000
1000
2000
3000
4000
SPAN 1
DESIGN MOMENT
(Moment is drawn on tension side)
Rebar Diagrams
Project: "" / Load Case: STRENGTH_1_Max_LL
+1.20 SW +1. 60 LL_Max +1.20 SDL +1. 60 XL +0.00 LAT
Rebar Required Top Rebar Required Bottom Rebar Provided Top Rebar Provided Bottom
1.0
0.8
0.6
0.4
0.2
Rebar [in²]
-0.2
-0.4
-0.6
-0.8
-1.0
SPAN 1
REINFORCEMENT
REQUIRED AND PROVIDED
Moment Diagrams
Project: "" / Load Case: Envelope
-7000
-6000
-5000
-4000
Moment [k-ft]
-3000
-2000
-1000
0
1000
2000
3000
4000
SPAN 1
DESIGN MOMENT
(Moment is drawn on tension side)
Rebar Diagrams
Project: "" / Load Case: STRENGTH_1_Max_LL
+1.20 SW +1. 60 LL_Max +1.20 SDL +1. 60 XL +0.00 LAT
Rebar Required Top Rebar Required Bottom Rebar Provided Top Rebar Provided Bottom
120
100
80
60
40
Rebar [in²]
20
-20
-40
-60
SPAN 1
REINFORCEMENT
REQUIRED AND PROVIDED
Legend (2.1):
Span C = Cantilever
Form 1 = Rectangular, 2 = T or Inverted L, 3 = I, 4 = Extended T or L section
Rh Elevation of top surface
TF Top flange
MF Middle flange
BF Bottom flange
Legend (2.7):
The Column Boundary Condition (CBC):
Fixed at both 1
Hinged at near end, fixed at far end 2
Fixed at near end, hinged at far end 3
Fixed at near end, roller with rotational fixity at far end 4
LC Lower Column
UC Upper Column
Legend (3.1):
Class: SW: Selfweight, LL: Live Load, SDL: Superimposed Dead Load, X: Other Loading
Type: U: Uniform, P: Partial Uniform, L: Line Load, M: Applied Moment
C: Concentrated Load, R: Triangle, V: Variable, T: Trapezoidal
Legend (12):
d: Effective depth of section for shear rebar calculation
Vu: Ultimate shear
Ratio: ratio of ultimate to allowable shear stress
Req.: Required shear reinforcement per unit length
Spacing: Spacing between shear rebar