Escolar Documentos
Profissional Documentos
Cultura Documentos
MODULES
For the 4200 Family
DWDM C-Band
D Datasheet
All OA modules are full width cards installed directly into the a significant benefit to network operators by allowing them to
card cage of a 4200 chassis, and both module types provide simplify network planning and installation.
system controller functionality. The variable-gain amplifier is
As managed resources, the optical amplifiers are provisioned
equipped with an integrated Optical Supervisory Channel
and monitored from any native management interface or
(OSC)1 which provides out-of-band node management.
via the ON-Center® NCS, the companion network
In particular, the OAV can fully exploit the bandwidth of the management system. The OAs also collect data to monitor
fiber plant without having to re-engineer the network by the performance of the service and optical layers, facilitating
dynamically adjusting for varying degrees of span loss, which rapid network diagnosis and fault isolation at any point along
can be as much as 1 dB as fiber ages. This capability provides the optical path.
Technical Information2
Optical Properties
Fixed 0A (OAF-00-1-C)
Parameters Minimum Typical Maximum Comment
Wavelength Range (nm) 1529.55 1565.50
Loss of input signal alarm (dBm) -40 0 Provisionable in the range
Overload input power (dBm) -3.0
Input power range (dBm) -21.5 -3.5
Maximum output power (dBm) 17.5
Gain (including connectors ) (dB) 19.0 20.5 22.0 Pin = -21.5 to -3.0 dBm
(across wavelength, power,
temperature)
Peak-to-peak gain variation (across 1.5 2.0 Pin = -21.5 to -3.0 dBm
wavelength, power, temperature)
(dB)
Peak-to-peak gain variation (across 1.0 Pin = -21/.5 to -3.0 dBm
wavelength and power @ 25 °C)
9dB)
Noise Figure (dB) 5.0 5.5 Pout = 17 dBm
Transient response time (µs) 500
Variable 0A (OAV-0S-U-C)
Parameters Minimum Typical Maximum Comment
Wavelength Range (nm) 1529.55 1565.50
Loss of input signal alarm (dBm) -40 0 Provisionable in the range
Overload input power (dBm) -0.6 @ 17.5 dB gain set point
-5.6 @ 22.6 dB gain set point
Input power range (dBm)3 -24.6 -0.6
Maximum output power (dBm) 17.5
Adjustable Gain Range 16.6 17.6 18.6 @ 17.7 dB gain set point
21.6 22.6 23.6 @ 22.6 dB gain set point
Peak-to-peak gain variation (across wavelength, 1.5 2.0 Pin = -24.6 to -0.6 dBm
power, temperature) (dB)
Peak-to-peak gain variation (across wavelength 1.0 Pin = -24.6 to -0.6 dBm
and power @ 25 °C) 9dB)
1
The fixed-gain OA does not have an integrated OSC; however, OSC connectivity can be achieved through either a co-resident variable-gain amplifier or a dedicated OSC module. See separate OSC Data Sheet for more information.
2
Note that the scope of these specifications is limited solely to the modules themselves and not the chassis in which they are installed. Chassis specifications are provided in the 4200 Family brochure.
3
Unit can operate over a wider input range, but may exceed one or more specified operating parameters.
2
Technical Information continued
Network Management Two (2) 10/100BaseT Ethernet ports for remote connectivity, access to node
level HTTP interface and access to SNMP agent, SNMP v1 (RFCs 1155-1157),
SNMP v2c, SNMP v3, CLI, Telnet, HTTP, FTP, RS-232 serial port for local craft
access, Optical Supervisory Channel (OAV module only)
Power Requirements
Module Voltage (V DC) Current Draw (A) Power Consumed (W)
OAF-00-1-C +12 3 36
OAV-OS-U-C +12 4 48
Environmental Characteristics The optical layer cards are designed to operate within the confines of a 4200 chassis, which provides the
forced-air ventilation necessary to sustain their operation.
Physical Characteristics 1.0” (H) x 10.82” (W) x 9.62” (D), 25 mm (H) x 275 mm (W) x 244 mm (D)
Ciena may from time to time make changes to the products or specifications contained herein without notice. Copyright © 2011 Ciena® Corporation. All rights reserved. DS106 10.2011