Escolar Documentos
Profissional Documentos
Cultura Documentos
class_parameter
WAC Identifier
This parameter defines the pointer to the WAC object identifier. It defines the WAC parameter set to be used in this virtual cell.
This parameter identifies the WAC object instance uniquely. The default parameter set is in the WAC object instance with
WACId=1.
This parameter defines the origin of the last configuration action affecting the object.
Pointer to the WAC object identifier. Defines the WAC parameter set to be used in this cell.
Range system_default class modification Feature
PFL HSPALoadMargin
FMCI MBLBInactivityRSCPThr
FMCI MBLBMobilityOffset
FMCI MBLBMobilityRABComb
IUCS IuState
IUPS IuState
RNMOBI MBLBGuardTimer
WCEL_HC DirectedRRCForHSDPALayerEnab
WCEL_HC HSDPALayeringCommonChEnabl
WCEL_HC MBLBEnhancementsEnabled
WCEL_HC MBLBInactivityEnabled
WCEL_HC MBLBLoadInfoDistr
WCEL_HC MBLBMobilityEnabled
WCEL_HC MBLBRABSetupEnabled
WCEL_HC MBLBRABSetupMultiRAB
WCEL_HC MBLBStateTransEnabled
WCEL_HC MaxNumberUECmSLHO
WCEL_HC WCDMALTELoadBalEnabled
description
This parameter determines the minimum required margin, by which the HSPA load level of the source cell//layer must exceed the HSPA load level of the target cell//layer, befo
balancing reasons./n/nTh
This parameter determines the minimum required CPICH and RSCP level, which must be achieved by the measurement result of the source cell, before multi-band load balanc
enhancements to inactivity triggere
Multi-Band Load Balancing due to mobility can be done when the quality criteria defined with this parameter is met. Quality criteria is evaluated comparing CPICH Ec//No of
currently used and CPICH
This parameter defines the RAB combinations for which Multi-Band Load Balancing due to mobility is allowed.
This parameter describes the state of the Iu interface of the CN Node connected to the RNC. This parameter is given to every CN Node connected to RNC. The parameter is use
routing decisions. /nThe
This parameter describes the state of the Iu interface of the CN Node connected to the RNC. The parameter is given to every CN Node connected to the RNC. It is used by the
decisions. /nThe descript
This parameter determines a period of time during which Multi-band load balancing handover or layering is denied after successful Multi-band Load balancing handover due t
Enables // disables the use of the Directed RRC connection setup for the HSDPA layer in the cell./n/nWhen Multi-Band Load Balancing is enabled in the cell for RAB setup phas
functionality behind this parameter
Enables // disables the use of HSDPA layering for UEs in common channel features in the cell./n/nWhen Multi-Band Load Balancing is enabled in the cell for the state transition
parameter is not applied.
This parameter enables the functionalities of the RAN3093 Enhanced MBLB (Multi-Band Load Balancing) feature./n/nThe functionalities that are related to the MBLB enhance
when the value of the corr
This parameter defines if Multi-Band Load Balancing is enabled when inactivity is detected in Cell_DCH state. If this parameter is enabled, Multi-Band Load Balancing is done w
state./n/nWhen this paramete
This parameter defines whether the HSPA load information (used in Multi-Band Load Balancing) of the cell is distributed inside the RNC. This same information is also distribut
(MBLBRABSetupEnabled, M
This parameter defines if Multi-Band Load Balancing is enabled due to mobility in Cell_DCH state. If this parameter is enabled, Multi-Band Load Balancing is done with handov
This parameter defines whether Multi-Band Load Balancing is enabled in the RAB setup phase. If enabled, Multi-Band Load Balancing is done with blind handover, which is ba
cell. Note! To enable blind han
This parameter defines whether Multi-Band Load Balancing is enabled for the multi RAB in the RAB setup phase. If enabled, and if parameter WCEL-MBLBRABSetupEnabled is
handover, which is based on R
This parameter defines if Multi-Band Load Balancing is enabled in state transition to Cell_DCH state. If this parameter is enabled, Multi-Band Load Balancing is done with layer
measurement from the source or
The parameter defines the maximum number of UEs that are simultaneously in a DCH compressed mode in the cell due to a service- or load-based handover, HSPA capability
LTE redirection // handover with
This parameter enables WCDMA-LTE Load Balancing feature in the cell. If WCDMA-LTE Load Balancing feature is enabled in the cell, it is checked if the incoming handover from
feature also det
class_parameter class parameter parameter_value_mapping_name
1 0 0
1 0 0
1 0 0
0 1 0
1 0 0
1 0 0
0 1 0
1 0 0
0 1 0
0 1 0
0 1 0
ref
0
0
0
0
0
0
0
0
0
0
0
class parameter_value_mapping_name order db_value
WCEL PtxPrimaryCPICH 1
ui_value proposed condition condition_value type scaleM scaleD
1 2 1 10
shif minv maxv stepv