Escolar Documentos
Profissional Documentos
Cultura Documentos
Driving Shafts
Straight
QFeature: Rotary Shafts suitable for driving motion. Accuracies and shapes needed for rotary driving applications are selectable.
QSelection of Driving Shaft
Type D Tolerance MMaterial HHardness SSurface Treatment Tolerance Circularity M
D
h7 h6
D
Hardened
Not Hardened
In selecting a driving shaft, select the basic shape and size from the specification table, then select necessary alterations such as thread machining, keyway addition etc.
KZAN -
10 0 0
10 <Selection Example of Part Number>
1045 Carbon - 0.015 - 0.009
0.004 · Alteration Selection: Two Keyways
KZAC h7
Steel
- Black Oxide 12 12
0 0
KZAP Electroless Nickel Plating 15 - 0.018 - 0.011 15 0.003
17 17 0.005
Ø40
1045 Carbon Induction Hardened 20 20
KZAF h6
Steel
- 0 0
Surface Hardness 50HRC ~ 25 - 0.021 - 0.013 25 Keyless Timing Pulley
30 30
0.006 50 100 <Example> Bearing with Housing
35 35
0.005 175 100
40 0 0 40
45 - 0.025 - 0.016 45
50 50
0.007 450
G EThe example below shows the keyway shape under the following conditions:
G M
G 6.3 1.6 1.6 When KA, KB, KC, KD, ZA, ZB, ZC, ZD=0
2−C0.5 When KA+HA, KB+HB, KC+HC, KD+HD, ZA+HA, ZB+HB, ZC+HC, ZD+HD=L
1.6 1.6 G
1.6 1.6 Roller - Straight with Keyway
*F or KZAF, will be .
D
*K ZAF may have
centering holes on
L±0.2 shaft ends.
F11-15_d03
Part Number - L - (MA, NA, KA, TA, SC, WA ··· etc.)
KZAF40 - 450 - KA50 - HA100 - KB175 - HB100
EPlease note that D dimension tolerance of KZAF is different from that of KZAN, KZAC and KZAP.
H
Min. L L100.5 L200.5 L300.5 L400.5 0˚ E3≤HA,HB,HC,HD≤100 EFor Keyway details, see P.710.
D ~100.0 ~200.0 ~300.0 ~400.0 ~500.0 ZB Angle Specified D 10~17 18~40 45, 50
· Ordering Code Keyway Keyway
ZA HA ZC Position Specified Width Specified
10 - - Angle Configurable ZB HB ZA HA
30° Increment
AA
H 1 2 3
12 - - ZD ZB HB AB
EThe length of each set screw flat is the same as that of each
keyway.
ZC HC
15 - ZC HC AC EFor a keyway and the angle of a set screw flat, the
ZD HD ZD HD AD tolerances may shift by up to ±0.2°.
17 -
W
Wrench Flats Adds a wrench flat. Specify the position of a wrench flat.
20 -
Ordering Code SC180 SC=1mm Increment 0≤SC≤L-L
25
30 SC D 10 12 15 17 20 25 30 35 40 45 50
35 W 8 10 13 14 17 22 27 30 36 38 41
40 L 8 10 15 20
SC l
45 -
50 - 2 Set Screw Flats (Angle Specified) Adds a flat at any designated angle besides the datum plane 0°.
Specify the position, the length and the angle of the set screw flats. When 0° is specified, only one set
H screw flat is machinable.
Ordering Code WA15-GA10-AA0
WA WA, WB, WC, GA, GB, GC=1mm Increment AA, AB, AC=30°Increment 0°≤AA, AB, AC≤330°
H
0°
WB
WA GA WC Set Screw Flat
Position Specified
Set Screw Flat
Width Specified
Angle Specified
30° Increment
D
H
10~17
1
18~40
2
45, 50
3
· Ordering Code
Angle Configurable
WB GB WA GA AA
WC GC WB GB AB
WC GC AC
1 -757 1 -758