Escolar Documentos
Profissional Documentos
Cultura Documentos
3. What door is used for kitchen? 12. What is the best thickness of gravel bedding?
a. Glass Door a. 100 mm
b. Double action door b. 200 mm
c. Flush Door c. 150 mm
d. Panel Door d. 300 mm
4. If you are to renovate a glass building, what should be used 13. Used for bonding ceramic tiles on walls and floors?
in order to minimize the heat generated inside the building? a. contact cement
a. Use tinted glass b. tile adhesive
b. Use CHB all over the building c. grout
c. Use CHB and minimal glass d. lead
d. Use wired glass
14. Used in doors to prevent smoke from entering the room?
5. What lock is used for toilet and bath? a. astragal
a. Double lock b. batidura
b. Lock inside c. hulog
c. Lock outside d. palitada
d. Single lock
15. Used in doors to prevent smoke from entering the room?
6. Upon application of Building Permit, what activity can be a. 6” CHB
done that is allowed by the OBO? b. bearing wall
a. Bending of Bars c. dry wall
b. Excavation d. shear wall
c. Layout of columns
d. Layout of footings 16. What kind of glass can redirect the suns reflection?
a. glass blocks
7. Why should you put primer on steel before painting? b. float glass
a. For adhesion c. plate glass
b. To prevent rust d. tempered glass
c. For easy welding
d. To prevent blistering 17. What should you use as a partition of T&B at second floor
to reduce the sound generated from flushing of toilet in
bedrooms?
a. Use 6” CHB wall 26. Is a term applied to certain aluminum products and refers
b. Use drywall w/ acoustic material in between gaps to the protective coating (cladding) applied, primarily for
c. place the closet adjacent to t & b corrosion resistance, to thin sheets of an alloy whose corrosion
d. use non-load bearing wall resistance has been decreased by the constituents added to
give strength and other characteristics. Cladding improves the
18. Where is the best location of the soil stack in the building? appearance of the alloy
a. inside columns a. ALCLAD
b. in between openings b. Cladding
c. away from exterior wall c. Alloy
d. in the exterior wall d. Metals
19. Wood not used as construction materials? 27. Aluminum used for roofing, flashing, gutter, etc.
a. palotsina a. aluminum foil
b. mahogany b. aluminum sheet and strip
c. coconut c. structural aluminum
d. yacal d. aluminum
20. What lock is used in the main door? 28. This is rigidized sheet fabricated of special aluminum alloys
a. single lock specifically developed for roofing and siding purposes. It
b. double lock usually consists of an aluminum alloy core of one type cladwith
c. lock inside another highly corrosion-resistant aluminum.
d. lock outside a. aluminum foil
b. corrugated aluminum
21. A building will be erected on a coastal area. What roofing? c. structural aluminum
a. use protruding eaves d. rib aluminum
b. provide big balcony
c. use roof deck 29. Aluminum finished that a can be obtained by grinding
d. use ribbed type roofing polishing, scratching, sandblasting, embossing, or other
treatment of the surface to achieve a desired effect or to
22. Used in vertical alignment? provide a base for other finishes.
a. astragal a. Mechanical finishes
b. batidura b. Chemical Finishes
c. hulog c. Electrolytic finishes
d. metros d. Electroplating
23. Where should you put the heat roofing material? 30. Aluminum finishes that are based on chemical reactions with
a. under the rafter the aluminum surface to achieve one of the following results:
b. under the ceiling (a)Floor Panel Wall Panel Ornamental Aluminum, Aluminum Mesh
c. over the rafter and Wire Cloth Pig Iron etching, cleaning, or polishing of the
d. on ceiling surface to remove any oxide film or surface irregularity and
provide a design, a clean surface texture, or a polished effect; and
24. Glass used in commercial establishments. (b) oxidizing of the surface with aluminum or other metallic oxides
a. float glass that protect the surface or serve as a base for subsequent
b. tempered glass treatment, or both. Chemical finishes permit only limited colors
c. reflective glass that are not as satisfying as the color films obtained on
d. plate glass electrolytically-applied (anodized) oxide films
a. Mechanical finishes
25. Is a soft, nonmagnetic silvery metal characterized by its b. Chemical Finishes
light weight (onethird that of iron, brass or copper), low c. Electrolytic finishes
melting point high thermal and electricalconductivity d. Electroplating
(surpassed only by silver and copper), and moderately high
coefficientof expansion.
a. brass
b. copper
c. metals
d. aluminum
HISTORY OF ARCHITECTURE
1. What is the World’s Largest Pyramid?
a. Saint
b. Titus Flavius Clemen’s Private Home
a. Pyramid of Cholula (Tlachihualtepetl) c. Burial Chamber of Roman Emperors
b. The Pyramid of Altun Hua d. A hill
c. Pyramid of Cheops
d. Pyramid of Lubaantun 6. What is the World’s Largest Brick Gothic Church?
23. In 1774, Fr. Miguel Murguia originally built a church on this 28. Which does not belong?
site. However, the church was severely damaged by a typhoon a. art noveau
on 17 January 1875. In 1884, a new church was erected. This b. le modern
church was built of coral blocks and is approximately 70 m long c. rayonnant
x 25 m. wide and 18 m in height. Its walls are about 3 m. thick. d. jugenstijl
It has the largest church bell in the country, weighing more
than 10 tonnes – crafted from about 70 sacks of coins donated 29. Which of the following is not a project of Skidmore, Owings
by the parishioners. In 1997, the church was officially declared & Merrill (SOM) in Manila?
a National Historical Landmark by the NHCP. Where is this a. Rockwell Center, Makati
church? b. PBCOM Tower, Makati
a. Malolos, Bulacan c. Zuellig Building, Makati
b. Panay, Capiz d. G. T. International Tower, Makati
c. Magdalena, Laguna
d. Balangiga, Samar 30. Who was the Architect of Manila City Hall?
a. Antonio Toledo
24. What is the most striking feature of the Barasoain Church in b. Juan Arellano
Malolos, Bulacan? c. Ralph Harrington Doane
a. Belltower d. Daniel Burnham
b. Pediment
c, Columns
d. Façade
25. What style was used in the columns in the facade of the
Barasoain Church?
a. Baroque
b. Romanesque
c. Gothic
d. Renaissance
4. Which theory of proportion uses the diameter of the column 10. What was the current name of the firm today?
as basic unit of dimension?
a. Palafox Associates
a. Golden Section
b. Francisco Manosa and Partners
b. Golden Rectangles
c. Casas + Architects
c. Fibonacci Series
d. Recio + Architects
d. Classical Orders
11. Which of the following indicates the brightness of a color?
ITEMS 5-7
a. intensity
5. The owner of the new Building originally promised to b. value
donate the Art Deco exterior limestone bas-relief sculptures of c. chroma
semi –nude goddesses, as well as the massive ornate above the
d.hue
old building’s entrance which were apprised at over USD
200,000 to the Metropolitan Museum of art. However, the new 12. "A house is a machine to live in".
owner decided to destroy them instead because of a possible 10-
a. Le Corbusier
day construction delay due to the works of art as junk. Robert
b. Walter Gropius
Miller, the gallery owner, lamented that such things can
c. Frank Lloyd Wright
“never be made again”. Who is the owner of the building?
d. Mies Van de Rohe
a. Ed Koch
b. Donald Trump
c. Der Scutt 13. What art principle shows the relationships between the
various parts of an object/structure/groups of objects and
d. Erwin Cantor
structures?
a. size
6. What is the official name of its structure?
b. volume
a. Trump building
c. proportion
b. Trump Tower
d. scale
c. Republican Building
d. Democratic Building
14. A style in the architecture Italy I the second half of the 16th 20. He created the Dymaxion House, "the first machine for
century and to a lesser extent elsewhere in Europe. It uses living".
classical elements in an unconventional manner.
a. Illusionism
b. Mannerism
c. Palladianism
d. Abstract
16. The architect who said that the exterior of the building is
the result of the interior.
a. Le Corbusier
b. William Ruskin
c. Mies van de Rohe
d. Frank Lloyd Wright a. Marcel Breuer
b. Louis Sullivan
17. What manifestation in a structure that identifies it as a c. Buckminster Fuller
work of architecture shows the adequate scheme or structural d. Le Corbusier
arrangement, effective choice of materials, and effective
construction system?
a. structural stability
b. utility
c. aesthetic sense
d. economic quality
19. "The man of learning… can fearlessly look down upon the
troublesome accidents of fortune. But he who thinks himself
entrenched in defense not of learning but of luck, moves one
slippery path, struggling though life unsteadily and insecurely."
a. A New Architecture by Frank Lloyd Wright
b. The Poetry of Architecture by John Ruskin
c. Space, Time and Architecture by Sigfried Gideon
d. Ten books of Architecture by Marcus Vitruvius
PLANNING
1. A tool used to control the manner in which raw land is 9. This code mandates that all Local Government Units shall
subdivided and placed on the market for residential prepare their comprehensive land use plans and enact them
development. through zoning ordinances.
a. zoning regulation a. HLURB Code
b. deed of restriction b. Local Government Code
c. subdivision regulation c. Civil Code
d. housing regulation d. Land use Planning
2. Planning for roads, bridges, schools, parking structures,
public buildings, water supply, land waste disposal facilities. 10. Written document to transfer the property to one person
a. capital facilities planning to another.
b. utilities planning a. Transfer Certificate Title
c. physical planning b. Deed
c. transport planning c. Clearance
d. Equity
3. The rough equivalent of the present tenement cities that
existed in ancient Rome, which resulted from the population 11. A wide area of parks of undeveloped land surrounding a
growth of the city and the congestion that existed in streets. community.
a. Tenema a. park
b. Insula b. open space
c. Agoras c. greenbelt
d. Domus d. plaza
4. The orderly arrangement of urban streets and public spaces. 12. In the Philippines, this type of land use planning
a. City Planning emphasizes the proper management of land resources to
b. Open Space Planning ensure that the present generation can benefit from its
c. Street Planning continued use without compromising future generations.
d. Spatial Planning a. coastal resource planning
b. land use planning
5. _____ of land, a contiguous land area which is considered as c. sustainable land use planning
a unit, which is subject to a single ownership, and which is d. strategic planning
legally recorded as a single piece.
a. Platting 13. A locale with a sizeable agglomeration of people having
b. Partition characteristics of an urban being.
c. Parcel a. city
d. TCT b. composite city
c. chartered city
6. The government arm responsible for the development and d. independent city
implementation of low cost housing in the Philippines.
a. National Housing Authority 14. First Planner and developed the Gridiron.
b. HLURB a. Marcus Vitruvius Poll
c. HUDCC b. Hippodamus of Miletus
d. Housing Agencies c. Mesopotamians
d. Daniel Burnham
7. Phrase used to characterize development that meets the
needs of the present generation without compromising the 15. A 20th century problem emanating from rapid urbanization
needs of the future generations. of areas surrounding a city which eats up the remaining
a. planned development adjacent rural open spaces.
b. sustainable development a. urban development
c. development-oriented b. urban sprawl
d. sectoral development c. urban gentrification
d. urban blight
8. A habitable room for 1 family only with facilities for living, 16. He conceptualized the 'City Beautiful Movement'.
sleeping, cooking, and eating. a. Le Corbusier
a. Single-detached unit b. Ebenezer Howard
b. dwelling unit c. Frank Lloyd Wright
c. living unit d. Daniel Burnham
d. housing unit
17. The container of man, which consists of both the natural PLUMBING
and man-made or artificial element. 1. When water comes out as soon as the fire sprinkler is
a. networks activated, the system is
b. links a. wet pipe
c. physical settlement b. pre-action
d. structures c. deluge
d. dry pipe
18. A type of planning which emphasizes that the proper role 2. When there is a low pressure from the water main, what will
of the planner is not to serve the general public interest but you use to supply higher levels?
rather to serve the interests of the least fortunate or least well a. booster pump
represented groups in society. b. sump pump
a. advocacy planning c. pneumatic pump
b. social planning d. jet pump
c. strategic planning 3. What type of material used for the base of a septic tank?
d. sectoral planning a. mass concrete
b. reinforced concrete
19. A profession which falls between planning and architecture. It c. lightweight concrete
deals with the large-scale organization and design of the city, with d. earth base
the massing and organization and the space between them, but 4. What is the typical slope of a waste pipe?
not with the design of the individual buildings. a. 1%
a. city planning b. 2%
b. urban design c. 3%
c. urban theorist d. 4%
d. city administration 5. Water enters through an open rim, as though a bucket of
water were dumped into the bowl, filling the front trapway and
20. Niemeyer believed that relating large areas to each other is creating siphon action. This model provides quick removal of
freedom as in the planned city of___. water with minimum water rise. Small water surface makes the
a. Chandigarh model more vulnerable to soiling and clogging. This is the least
b. Stalingrad efficient and most noisy type but lowest in cost.
c. Chicago
d. Brasilia
a. wash down
b. siphon jet
c. reverse trap
d. siphon vortex
a. wash down
b. siphon jet
c. reverse trap
d. siphon vortex
7. used to connect the two ends of two pipes, neither of which resulting in quick withdrawal of water from the bowl. A water
can be turned jet is located at the inlet of the trapway. Most of the bowl
a. coupling surface is covered with water. This model is efficient but
b. caulking moderately noisy. Its cost is reasonably low.
c. nipple
d. tread
8. This material is used to threaded pipe connections to a. wash down
prevent leakage
b. siphon jet
a. Teflon tape
b. solvent
c. reverse trap
c. fitting d. siphon vortex
d. pipe
9. The standard water pressure from nawasa, maynilad, manila
water etc.
a. 20 psi
b. 40 psi
15. Plumbing permit shall be invalid if works not commenced
c. 60 psi after a period of
d. 80 psi a. 120 days
10. The principal artery of the venting system to which vent b. 200 days
branches may be connected c. 1 year
a. main vent d. 2 years
b. loop or circuit vent 16. It is added to water to reduce salinity
c. local vent a. disinfectant
d. group cent b. solvent
c. electrolysis
11. The extension of a soil or waste stack above the highest d. salt purifier
horizontal drain connected to the stack horizontal drain, the
17. Is the lowest portion of the inside of any pipe or conduit
uppermost end above the roof that is not vertical
a. unit vent a. invert
b. stack vent b. based
c. relief vent c. under
d. dry vent d. over
18. Is the flow of water or other liquids, mixtures or substances
12. Strong flushing action is created by a jet of water directed into the distributing pipes of a supply of water from any source
into the rim and jet. The force of the jet draws the bowl other than its intended source
contents into the rear trap. It doesn't use siphonic action but a. back siphonage
relies on the driving force of jet action. At flush valve 25 psi is b. back pressure
needed with 1.5-in. inlet spud. Large water surface and large c. back flow
trapway size make this model efficient and suitable for d. behind flow
commercial use. Flushing is very noisy. Expensive.
19. Is the extended portion of a pipe that is closed at one end to
which no connections are made on the extended portion
a. last line
a. wash down b. dead end
b. pressure/tankless c. first line
c. pressure/tank d. second end
d. siphon vortex
20. Is the backflow of used, contaminated or polluted water
from a plumbing fixture due to negative pressure
a. back siphonage
13. Refers to any group of two or more similar adjacent fixtures b. back pressure
which discharge into a common horizontal waste or soil branch c. back flow
a. circuit of fixture d. behind flow
b. group of fixture
c. battery of fixture
d. develop of fixture
14. Water enters through rim punchings and through a jet that ELECTRICAL
fills the rear trapway completely, creating a siphon action and 1. One on which the circuit interaction occurs in air.
a. air circuit breaker b. ceiling plug
b. fuse c. ground
c. branch circuit d. plug
d. parallel circuit
2. A material that permits many electrons to move through it. 12. Machine that converts electric power to mechanical
Copper, silver, and aluminum are examples of materials that are a. electric fan
good conductors. Also used generically to refer to a wire, cable, b. DC motor
or bus bar that is made from a conducting material. c. motor
a. metal a. AC motor
b. semi-conductor 13. Insulating media for transformers (no longer allowed)
c. conductor a. mineral oil
3. Rated continuous current capacity of a conductor or device. b. askarel
(electrical devices should not exceed 12 amperes, or else it will c. Gatorade
burn) d. foam
a. capacity 14. Metal pipe in which electrical powers may be drawn; has
b. ampacity conditions (like wall is thinner than conduit)
c.amphere rating a. metal straw
d. volt b. steet pipe
4. A device that can be used to open or close a circuit manually c. electrical metal tubing
and can also open a circuit automatically when current is d. pipe
excessive. 15. XHHN in wire specification means?
a. air circuit breaker a. Moisture and Heat Resistant-Cross-Linked
b. circuit breaker Thermosetting
c. branch circuit b. Moisture resistant, in wet and dry location
d. group circuit c. Heat resistant in dry and wet location
5. A cable provided with wrapping of metal (steel wire) for d. Moisture and Heat Resistant- Linked Thermosetting
mechanical protection. 16. A high intensity discharge lamp in which the light is
a. steel cable produced by the radiation from a mixture of a metallic vapor,
b. super cable similar to that of a mercury lamp in construction.
c. armored cable a. mercury lamp
d. thick cable b. metal halide lamp
6. Where you connect the wires? c. tungsten halogen lamp
a. junction box d. high-pressure-sodium lamp (HPS)
b. match box 17. A type of lamp popular for lighting commercial interiors,
c. Johnson box uses argon gas to ease starting, it produces light by means of
d. carbon box an electric discharge in mercury vapor.
7. It is illegal because it bypasses the meter a. mercury lamp
a. hacker b. metal halide lamp
b. bumper c. tungsten halogen lamp
c. tracker d. high-pressure-sodium lamp (HPS)
d. jumper 18. A type of lamp which produces light by means of the
8. Circuit conductor between electric device and the outlet reaction of halogen additive in the bulb reacts with chemically
a. air circuit breaker with tungsten.
b. circuit breaker a. mercury lamp
c. branch circuit b. metal halide lamp
d. group circuit c. tungsten halogen lamp
9. Over current protective device (like a circuit breaker) d. high-pressure-sodium lamp (HPS)
a. bulb 19. In a lightning protection system, the combination of a
b. fet metal rod and its brace or footing, on the upper part of a
c. fuse structure
d. transformer a. ground rod
10. One with contact separate in air b. air terminal
a. air circuit breaker c. lighting rod
b. air switch d. protective assembly
c. conductor 20. TW in electrical wire specification means.
d. fuse a. Moisture and Heat Resistant-Cross-Linked
11. The third protruding metal stick in a plug Thermosetting
a. grounding plug b. Moisture resistant, in wet and dry location
c. Heat resistant in dry and wet location c. limit switch
d. Moisture and Heat Resistant- Linked Thermosetting d. current overload safety switch
9. In elevator, it makes the buzzer alarm when the car is
MECHANICAL, AUXILIARY & ACOUSTIC & LIGHTING overloaded and the door remains open until overloading is
1. This type of perimeter detector uses both the Passive eliminated.
infrared and Ultrasonic or Microwave system. a. safety shoe
a. microwave b. weighing device
b. passive infrared with ultrasonic (or microwave) c. fascia plate
` c. proximity / capacitance d. sheave
d. ultrasonic 10. An assembly consisting of a pulley wheel, side plates, shaft,
2. In escalators, this is located at the bottom truss of the and bearings over which a cable or roped is passed
escalator and provided with on and off positions to stop or a. governor
prevents the escalator from starting during maintenance b. weighing device
service. c. fascia plate
a. circuit breaker d. sheave
b. handrail guard switches 11. It prevents passengers from falling into the hoistway when
c. limit switch they try to get out of the car which is stopped between the
d. disconnect switch floors.
3. ___ of a partition, the number of decibels by which sound is a. safety shoe
reduced in transmission through it; a measure of the sound b. weighing device
insulation value of the partition, the higher the number, the c. fascia plate
greater the insulation value. d. sheave
a. transmission loss 12. The cooling effect obtained when 1 ton of ice at 32 oF (0
b. audible transmission oC) melts to water at the same temperature in 24 hrs.
c. sabin (equivalent to 12,000 Btu/hr)
d. decibel drop a. HP of refrigeration
4. The number of cycles per unit time of a wave or oscillations b. Ton of Ventilation
expressed in hertz of cycles per second. c. Ton of Refrigeration
a. wavelength d. HP of Ventilation
b. frequency 13. In elevator, these prevent the excessive car travel at the
c. sine wave highest and lowest floor.
d. sound wave a. disconnect switch
5. This switch cuts off all current supply to the escalator for b. knife switch
inspection, maintenance, or repairs. c. limit switches
a. disconnect switch d. current overload safety switch
b. knife switch
c. limit switch 14. A type of lamp which produces light by means of the
d. current overload safety switch reaction of halogen additive in the bulb reacts with chemically
with tungsten.
6. In elevator, it detects the obstacles during the door closing, a. mercury lamp
and reopens the door if there is something. Photocell can be b. metal halide lamp
used together with this. c. tungsten halogen lamp
a. safety shoe d. high-pressure-sodium lamp (HPS)
b. weighing scale
c. fascia plate 15. This device, in escalators, is provided at the drive unit
d. handrail guard location to protect against accidental movement of the
escalator during inspection of the drives or during general
7. This device, in escalators, stops the escalator automatically if maintenance.
an abnormal current is supplied to the motor. a. mechanical maintenance locking device
a. disconnect switch b. knife switch
b. knife switch c. limit switch
c. limit switch d. disconnect switch
d. current overload safety switch
4. Contract Documents under Article 3: Cost arising from 12. Contract Documents under Article 20: caused by
discrepancies in information instructions from architect or owner; delays in owner-supplied
a. clarification of meaning materials- within 15 days
b. discrepancies in drawings- a. claims for extra cost
c. coordination of drawings and specifications b. use of completed portions of work
d. copies of drawings and specifications c. search for causes of defects or faults
d. use of completed portions of work
5. Contract Documents under Article 4: setting drawings,
templates, patterns at contractor’s expense 13. Which of the following is not part of the construction
a. schedule for submission of detail and shop drawings team?
b. discrepancies in drawings- a. owner
c. supplementary drawings and instructions b. architect
d. copies of drawings and specifications c. contractor
d. real estate broker
6. Contract Documents under Article 3: necessary adjustments
to produce first class work 14. The following are daily inspection reports except:
a. clarification of meaning a. weather conditions
b. discrepancies in drawings b. manpower availability/distribution
c. coordination of drawings and specifications c. construction activities
d. copies of drawings and specifications d. all of the above
7. Contract Documents under Article 10: properly labelled; for 15. It prepares forms for contract letting, documents for
approval; pre-paid transportation cost bidding and for construction, assists owner in obtaining
a. trade name materials and substitutes proposals from contractors, decides on claims of owner and
b. storage and stockpiling of materials contractor, periodically visits the project site to monitor general
c. quality of materials progress and issues Certificates of Payment
d. samples of materials a. schematic design phase
b. construction phase
8. Contract Documents under Article 10: cost of removal and c. contract documents phase
replacement d. development phase
a. defective materials 16. Which of the following is not a method of compensation?
b. storage and stockpiling of materials a. multiple of direct personnel expenses
c. quality of materials b. professional fee plus expenses
d. samples of materials c. lump sum or fixed fee
d. all of the above
17. The following are under the Schematic Design Phase BUILDING LAWS
EXCEPT: 1. 1. The purpose of the NBC is to provide for all buildings and
a. ascertain project requirements structures, a framework of standards and requirements which
b. prepare schematic studies leading to a is the
recommended solution a. maximum b. minimum
c. submit probable construction cost c. regular d. definite
d. submits a further statement of probable
construction cost – (under design developement) 2. Under the NBC abutment on lot lines are allowed only in
a. R-1 zones
18. It prepares plans, elevations and other drawings, outline b. R-2 & R-3 zones
specifications, illustrate the size and character of the project c. Fire zones
and submits a further statement of probable construction cost d. prohibited zones
a. schematic design phase
b. design development phase 3. Under the NBC, every corridor and exterior exit balcony
c. contract documents phase servings as a required exit for an occupant load of more than
d. development phase ten width shall not be less than
a. 1.10 mts b. 1.20 mts
19. Projects involving extensive detail such as furniture design, c. 1.40 mts d. 1.50 mts
built-in equipment, special fittings, screens, counters, interiors
and other detailed parts of appurtenances of buildings or 4. Under the NBC, the vertical distance between landings shall
structures and landscaping designs not be more than
a. Group X a. 2.5 mts b. 3.00 mts
b. Group IX c. 3.30 mts d. 3.60 mts
c. Group VIII
d. Group V 5. Under the NBC, open spaces for corners and through lots is
a. 10% b. 20%
20. The practice of the act of managing, administering, c. 40% d. 50%
directing, coordinating, supervising and giving general 6.Under the NBC, open spaces inside lots is
administration and responsible direction to the operation and
a. 20% b. 30%
maintenance of buildings and their utility systems and
c. 40% d. 50%
equipment, in order to enhance their usefulness
7.Under the NBC, space required for interior lots is
a. building administration and management
b. administrative function a. 20% b. 30%
c. technical staff c. 40% d. 50%
d. consultant
8. Under the NBC, the minimum dimension for court or near
yard from the property line to the face of the building is
a. 1.50 mts b. 2.00 mts
c. 2.50 mts d. 3.00 mts
9. Under the NBC, a building in R-1 zone shall comply with the
open space requirement in the form of
a. 3.00 mts b. 4.00 mts
c. 5.00 mts d. 6.00 mts
11. Under the NBC, the interior lots shall have an access road
with a minimum width of
a. 1.50mts b. 2.40 mts
c. 3.00 mts d. 3.60 mts
12. Under the NBC, gasoline filling and service stations shall STRUCTURAL
classified under what occupancy classification? 1.) Allowable stresses for tension in structural steel in terms
a. accessory of gross area:
b. assembly a. 0.60 of the specified minimum yield stress
c. industrial b. 0.50 of the specified minimum yield stress
d. business & mercantile c. 0.45 of the specified minimum yield stress
d. 0.66 of the specified minimum yield stress
13. Under the NBC, display windows or wall signs within how 2.) Allowable shear stress on structural steel on the cross
many meters above the sectional area effective in resisting shear:
sidewalk a. 0.40 Fy
a. 2.40 mts b. 2.70 mts b. 0.50 Fy
c. 3.00 mts d. 3.30 mts c. 0.60 Fy
d. 0.90 Fy
14. Under the NBC, areas where adequate parking lots/ multi-
floor parking garages are available within 200 mts. of the 3.) The effective area in resisting shear of rolled and
proposed building / structures only what percent of the parking fabricated shaped may be taken as:
requirements maybe provided within the premises? a. overall depth times the web thickness
a. 10 % b. overall depth times the flange thickness
b. 15% c. flange width times overall depth
c. 20% d. overall flange thickness times width of flange
d. 25%
15. Under the NBC, general units of measurement on 4.) For structural carrying live loads which induce impact, the
consonance with the current worldwide practice follow the assumed live load shall be increased sufficiently to provide
a. Uniform Construction Index for same. For supports of elevators the increase shall be
b. International Standard __________:
c. System International a. 100%
d. English System b. 30%
16. Under the NBC, the minimum requirements for a parking c. 33%
space is d. 50%
a. 600 mm b. 750 mm
c. 900 mm d. 1000 mm 5.) The lateral force on the crane runaways to provide for the
17. Under the NBC, for Group A Dwellings, stairs shall have a effect of moving crane trolleys, shall be _______% of the
clear width of at least sum of the weights of the lifted load and the crane trolley
a. 2.30x4.70 b. 2.50x5.00 but exclusive of other parts of the crane:
c. 2.80x5.50 d. 3.00x6.00 a. 20%
18. Under the NBC, mezzanine floors shall have a clear ceiling b. 30%
height not less than how many? c. 10%
a. 1.80 mts b. 2.00 mts d. 15%
c. 2.10 mts d. 2.40 mts
19. Under the NBC, hospitals shall have one parking slot for 6.) Piles that are driven at an inclination to resist forces that are
every how many beds? not vertical are called:
a. 15 b. 20 a. batter piles
c. 25 d. 30 b. spur piles
20. Under the NBC, all inner courts shall be connected to a c. slanting piles
street or yard either by a pass d. all of the above
with a minimum width of
a. 1.20 mts b. 1.50 mts 7.) A buried plate or block tied to and forming an anchorage for
c. 1.80 mts d. 2.00 mts sheet piling or for a retaining wall is a:
a. Anchor Plate
b. Block Plate
c. Dead Man
d. NOTA