AMX
‘DESGHETION AULT AREA, a}
101 | charger aut |
102 ‘charger Fault
103 ‘charger Fault
104 Charger Fut
a Chorger Fou a
106 Fehr out el
107 = Chorger Fault
210 = z
2
Left Dive Stal
ight Drive Stall
24
215 =
| a Drive Foul
Drive Fou
‘Generator Fault
‘Generator Fault
2 “Check Display Control s
3 Displar Error 23 ‘Check Display Controle
26 328 —[stteny Fault =
2 a2F Calbration Faut (RAM Defective
30 430 (Generator Fault
SE 431 (Generator Fault
32 [a3 Generator Fault
33 40 (Generator rou
35 435 (Generator Fault
36 436 ‘Generator Fault
[ar 437 ‘Generator Fault
38 439 (Generator Fault
(Generator Fout
seneralor Feu
(Generator Fout
‘Generator Fault
‘Gererator Fault
‘Generator Fou
‘Generator Faut
‘Generator Fault
Generator Faut
Generator Fauk
Generator Faut
Generator Faut
(Generator Fault
(Generator Fault
(Generator Fault
Section § Page 1
Revs
Published August 2011ag seme [Generator Fou
S| a (Generator Fait
es a ‘Generator Faut
= ‘Generator Fait =
[Generator Fault ‘
enertor Fou
Senertor Foul
[ ceertor aut
Ceneator Fut
| Generator Fat
Halting Ero 70
[81 Ener Checsum [Test 01 Fad :
[ez RaW battery Test | Test=02Fabad ———
[ea Aue RAM Test [Te
Test = Fale ‘Check Calibration
Test —5 Fake (Check CPU
Test 96 Failed Check PU
rogam
Intermittent Timer 0/2 87
LADD Converter ‘est — 7 Failed __| check +5v Supply
Power Up Tests: When the system is tmed an, the CPU wll perform a self est routine. The tests
performed are as follows:
+ WO Response on Display ~ Check the Leds on the CPU board. If all ON the CPU snot executing
test routine. Al OFF may mean tes fale or bad ed array.
‘+ Test O1~ Eprom Checksum est, The CPU calculates anew checksum and compares twit the
stored checksum in the Epron,
‘+ Test 02 RAM Read/Write Tast. The CPU wll ite tothe RAM then read it back and compare Ito
be orginal data. RAM 1 tes
+ Test 03~ Auxliry RAM Read/Write Test. The CPU checks switch §75(596) f dosed only 2K of
RAM, open 4K of RAM, The CPU wil write tothe RAM and then read it back and compare
the original data. Ram 2 tes.
‘+ Test of ~ Casraion Data Base Checksum. The CPU will generate a new Callbation Data Base
[Checksum and compare it tothe Stored Calibration Data Bate Checksum, Eprom 2.
‘+ Test 05 Watchdog Timer. The CPU wll write and ead the Wachdg timer. The Time should be
about 50 ms
+ Test 06 ~ Programmable Interval Timers. The CPU wil check Timer 0 for L6KHZ and Timer 1 for
20K,
‘+ Test 07 ~ A/D Converter. The CPU wil read the 5 vot supply. 5 volts +/-.5 vals. IFoption switch
's set (5755 (596}sw3), the CPU wil check the +24 vo, +19 vot and -15 wot supplies,
Section 5 Page 2 Rev 4
Publishes August 2011,ERROR CODE DI
ERROR 12/13 RELEASE HANDLE
Left and right stall signal detected
(Occasional occurrence fs normal (J. thresholds elevators)
1. Check snubbers (Back fter) on motor relays
2. Check brakes oF motor (35 & 36 on drive amp)
5. Checkmotors (Le. noisy, check brushes, 18 22 on deve)
ERROR 19 RELEASE HANDLE
Normal the unit being dive fast down an inline
T1"Release Handle Message" displays during engaging enable baron dive handle
1, Imeratent contact on micro svtches or pushbutton switch (ld style) in
sve once,
2. Drive Uses Fa 8 F2 (8 amp)
3. Connectons at arve module
a
Connections at drive handle
ERROR 23, DISPLAY ERROR
Indicates display contr problems,
1. Chedlog transformer
2. Gheckribbon cable to dive contra (.e plugged up corey)
ERROR 44 BATTERY TOO HIGH
Battery voltage too high ding prep. If ths happen after unplugging unt from charge
‘jl; surface charge needs tobe bled off (i. ave unt; colimator ight on)
1.1520 minute wat recommended ater charge
2 Lower techniques Ox at high battery vottage
ERROR 45, BATTERY TOO LOW
1. Charge batteries
‘Check batteries
Recalerate battery charger
ERROR 70 HALTING ERROR
Does sit pass power up test?
Excessive noise; check ground connestions
iatetog timer ercutry on CPU bod
Replace CPU
ERROR 101-107 (CHARGER FAULT
Charge Errors
1 Recalbrate battery charger
2. —Replce battery charger
3. Replve ebb cable (CPU to charger)
4. Bxcesave tne votage drop
5. Check voltage across ANDIARRI (big resistor near battery ground stud)
ERROR 210-212 rive FAULT
‘Check clive contra board for proper feedback
Th Feedtack 5 volts when uni nat moving
2. Shou move SV in one drecton and above SV inthe other direction
Section § Page 3 Rev 4
Published August 2011