Escolar Documentos
Profissional Documentos
Cultura Documentos
For sid801/803 system, this fault code represents the High pressure pump Flow
regulator. There have been cases that require a new high pressure pump assy.
This code can also be generated for cases of hesitation at low engine speeds, this
maybe attributed to the electronic EGR valve sticking open.
________________________________________
P0011
For MM6LP; Check for temperature problems. Excessive engine temperature will cause
the ECU to limit the valve timing advance.
________________________________________
P0101
For EDC15C2, this fault represents:
- Air flow not sufficient against expected value.
Check the EGR valve operation.
- Air flow too great or not sufficient.
Check the calibration of air flow meter. Also check for turbo hoses adrift or
split.
________________________________________
P0102
For SID 803, check the air flow sensor. I created this fault code when
disconnecting the sensor.
________________________________________
P0117
For ME7.4.4 as fitted to TU5jp4; Check for the additional, 118 degree, heat switch
failure. It shorts out the coolant thermistor circuit. (Parallel wired).
For MM6LP, I have had occassions of the temperature sensor reading excessively high
temperatures, around 140 �C. With this sort of temperature, look out for other
faults relating to long term temperture control. Such as long term fuel trim etc..
________________________________________
P0136
For MM6LP as fitted to ET3 engine, confirm oxygen sensor failure by checking
voltage across circuit. Should be approx. 3.8 volts open circuit.
________________________________________
P0170
This fault code is generated as a result of long term fuel trim information.
For MM6LP as fitted to ET3 engine, this fault may relate to the oxygen sensor as
early sensors were known to be faulty. However make sure there is no other cause of
fuel trim being affected. Check for temperature problems. I have noticed that with
excess temperature, the ECU shuts down the heater control of the Oxygen sensors.
________________________________________
P0234
For EDC16C3; Possible causes:
Turbo failure
________________________________________
P0238/P0069
For EDC16C3; Possible causes:
Turbo failure. This fault can be attributed to turbo wastegate calibration. No
physical fault with component but incorrect setting of wastegate, causing over
boost under certain conditions. This fault code is also generated by diconnecting
the sensor.
________________________________________
P0299
For SID 803; Check vacuum supply to controller solenoid, they have been known to
leak vacuum.
I have seen an EDC16C3 system with a recked turbo.
________________________________________
P0337
For EDC16C3 as fitted to 206 DV4td; Check for engine speed sensor harness damage.
Harness retaining clip can be dislodged and the harness may catch the right hand
drive shaft.
________________________________________
P0351~P0356
For ME746 or similar, check the primary current very carefully. You may find you
check the primary resistance and find no fault, but I have had incidents where the
resistance was identical on all cylinders but the current whilst operating was
different.
________________________________________
P0380
For EDC15C2 and possibly other Pre heat systems, check for open circuit glow plugs.
________________________________________
P0400
For EDC15C2 check for vacuum at EGR valve. Check for vacuum supply to solenoid
valve and output from solenoid valve. The control duty at 99% sould be valve fully
open.
________________________________________
P0401
For EDC15C2 intermittent faults, check for water presence in the air filter, or
some other similar obstruction. (Favourite after flood water).
________________________________________
P0402
For EDC16C3, check for obvious causes including blown turbo.
________________________________________
P0410
For MM6LP; this fault is often attributed to the auxillary air pump failing,
usually by water ingress. Check the pump for water content.
________________________________________
P0414
For MM6LP; Check the auxiliary air pump for siezure, usually caused by water
ingress. Also check the fuse supplying it. (BM34).
________________________________________
P0422
For EDC16C3, this fault relates to the particulate filter, Maximum number of
aborted regenerations reached. Look for other faults which may cause this to occur.
It may not be the filter.
________________________________________
P0490
For SID 803; This fault relate to the Electronic EGR valve, which sticks after some
use. It will probably require replacement.
________________________________________
P0745/P0932
For AL4 gearbox; check the pressure sensor operation.
________________________________________
P1110
For Sagem S2000, as fitted to TU engines; Check the MAP sensor, (dual function
sensor), for oil contamination, usually oiled up after engine over filled with oil.
________________________________________
P1138
For EDC15C2, as fitted to DW10 engines, this fault code may indicate a power supply
interruption to the rail pressure sensor. There was a modified intermediate harness
supplied, which had to be fitted with a new sensor and harness retaining clip. This
was to correct a connection fault, however do not dismiss other causes of incorrect
pressure readings.
________________________________________
P1153
For MM6LP, as fitted to EW10 and ET3 engines; Check motorised throttle unit and ECU
software version. ECU download often required for this fault.
For ME744, this fault can occur after ECU download. Usually requires Throttle
butterfly learning to be carried out.
________________________________________
P1167
This fault code for AL4 is often generated along with P0745. It relates to pressure
regulation and is very often caused by hydraulic block failure, usually caused by
solenoid swarf. Make sure you have the latest Borg Warner solenoids fitted and
software to match. The solenoids are included in the new hydraulic block assembly.
Also be aware that the pressure sensor may be at fault. Unfortunately this does not
mean the gearbox as a whole is not faulty, as the swarf damage very often causes
the box to fail internally or the brake bands and gear bearings also wear and cause
contamination. Depending on age and mileage etc. it maybe prudent to just opt for a
new gearbox, especially if coupled with 'slip' faults.
________________________________________
P1291
For EW10D, SIRIUS81, check the operation of the high pressure fuel pump. This code
seems to relate to failure. I have witnessed this fault, with the HP pump dropping
pressure off, intermittently, and the regulator trying to increase pressure, as
expected.
________________________________________
P1327
For S2000P; check ignition primary pattern for excessive peak voltage and spark
line too short. Should be greater than 1ms. This fault code is usually caused by
interference.
________________________________________
P1336
For TU5jp4 with ME7.4.5., check for Compression faults. I have witnessed, on more
than one occassion, burnt exhaust valves on cylinder No.2..
________________________________________
P1351
For SID 803, check the operation and output of the pre-heat control relay.
________________________________________
P1429
For EDC15C2; Check the Exhaust differential pressure sensor. It has a habbit of
becoming contaminated with water. Checks I have made show the following:
0.500 volts = 0.0mb / 0.550 volts = 5.9mb / 0.565 volts = 11.6mb.
________________________________________
P1435
For EDC15C2, this fault code represents many different descriptions as you have
seen. Check the additive tank for fluid level. I have seen this fault when the tank
is empty even when the additive ECU says the minimum level hasn't been reached.
Early 406 DPX42 additive level sensor voltage I measured as follows: Presumed empty
tank - 891mv, plus 2 litres - 827mv. Or > 1.8 Kohms is empty.
If you have to check the fuel cap sensor, the resistance is 149 Kohms cap on, 12 ~
15 ohms cap off.
________________________________________
P1446
For EDC15C2; Not too sure about this code, but I believe the term 'Wait' is a miss
translation for 'Reached', which therefore corresponds to the level being too low.
However the term 'Reached' is sometimes reported.. Check the level sensor
resistance to confirm status. > 1.8 Kohms is empty. (DPX42 system). I am looking
into this issue.
It seems there is approximately 100 ohms difference between empty and full,
although the sensor only reports 'empty'. It uses a current compensation method for
controlling level information.
________________________________________
P1447
For EDC15C2; Check for inverted pipe configuration on differential pressure sensor
or water ingress.
________________________________________
P1458
For PSA systems with additional Heat switch, Component No. 1289 2v be connector,
118�C warning, as mounted on the heated water housing. The circuit is wired in
parallel with the coolant thermistor.
________________________________________
P1471
For DV4/6 euro 4 emissions; this fault code relates to the 'RAS', (Intercooler/heat
exchanger), control solenoids/butterflies.
________________________________________
P1641
For SID 801; Check the Piezo electric injectors. They complete the power stage for
the ECU driver. If they are in question, they probably need replacement, even if
their capacitance readings are Ok. In addition, this code maybe attributed to the
physical driver stage in the ECU, therefore the ECU maybe at fault.
In a case that I had with this fault code, the solution was to replace both the ECU
and the injectors.
A more recent event, found the problem was caused by a single injector wire
shorting to ground. (When I say shorting, it was approximately 2 MOhms to ground,
which was caused by a slightly chaffed wire surrounded by moisture).
________________________________________
P1607/P1671
For MM6LP I have found this fault caused by a software issue in the BSI. A hard
reset for the BSI may sort it out temporarily.
________________________________________
P1687
For Lucas DCN2 as fitted to DW8B engine in Partner vehicle, this code is generated
as a result of fuse number 2 in the engine fuse box being present. This is a hard
fault code and will not clear. Remove the fuse from the engine fuse box (it should
never be fitted), clear the fault codes. Disconnect and reconnect the battery,
allowing the 3 minute rule etc.
Retest and read faults after connection.
It also maybe attributed to the status of matching between the pump module and the
immobiliser ecu. Status 'Unlocked'
________________________________________
P2101/P1161
For S2000PM1 as fitted to TU3 engine in Citroen C3, check for harness problems. It
may be necessary to replace the multi connector on the motorised trottle unit and
delete the connector under the glove box, where the manufacturer has adapted from
left hand drive.
P2408
All the tank cap present sensors I've tested, so far, should read:
149Kohms = cap on, 12~15ohms = cap off.
________________________________________
P2191
For EP6DT engine, this fault code has often been associated with Cam Timing.
________________________________________
P2562
For SID 803; Check for turbo control vacuum supply, possibly too weak. Look at
other solenoid valves for vacuum leakage. (Stable 750mb vacuum with engine
running).
________________________________________
P2563
For SID 803; Check for turbo control vacuum supply, possibly too weak. Look at
other solenoid valves for vacuum leakage. (Stable 750mb vacuum with engine
running).
********************************
*****************************
9609 Rear left side airbag fault present but not configured : Coherence fault
960A Rear right side airbag fault present but not configured : Coherence fault
960B Left-hand side curtain airbag fault present but not configured : Coherence
fault
960C Right-hand side curtain airbag fault present but not configured : Coherence
fault
960D Driver's knee airbag fault present but not configured : Coherence fault
960E Passenger's knee airbag fault present but not configured : Coherence fault
9610 Front left satellite fault present but not configured : Coherence fault
9611 Front right satellite fault present but not configured : Coherence fault
9612 Rear left satellite fault present but not configured : Coherence fault
9613 Rear right satellite fault present but not configured : Coherence fault
9614 Front left satellite fault : Coherence fault
9615 Front right satellite fault : Coherence fault
9616 Front left door satellite (additional) fault : Coherence fault
9617 Front right door satellite (additional) fault : Coherence fault
9650 Supply voltage fault : Coherence fault
9651 Supply voltage fault : Coherence fault
9660 Fault with the passenger airbag deactivation switch : Coherence fault
9665 Driver's seat position sensor fault : Coherence fault
9666 Passenger seat position sensor fault : Coherence fault
9670 Fault in driver's anti-submarining airbag present but not configured :
Coherence fault
9671 Fault in passenger's anti-submarining airbag present but not configured :
Coherence fault
9675 Fault on the LH front and rear lateral airbags in series, present but not
configured : Coherence fault
9676 Fault on the RH front and rear lateral airbags in series, present but not
configured : Coherence fault
9677 Driver's strap return pretensioner fault present but not configured :
Coherence fault
9677 Fault in the front RH seat belt pretensioner: present but not configured :
Coherence fault
9690 Fault on the LH lateral and LH curtain airbags in series, present but not
configured : Coherence fault
9691 Fault on the RH lateral and RH curtain airbags in series, present but not
configured : Coherence fault
9692 Row 1 and 2 left-hand pretensioners in series fault present but not configured
: Coherence fault
9693 Row 1 and 2 right-hand pretensioners in series fault present but not
configured : Coherence fault
9694 Row 2 and 3 left-hand pretensioners in series fault present but not configured
: Coherence fault
9695 Row 2 and 3 right-hand pretensioners in series fault present but not
configured : Coherence fault
9696 Row 2 central pretensioner fault present but not configured : Coherence fault
9697 Row 3 central pretensioner fault present but not configured : Coherence fault
9698 Driver and passenger pretensioners in series fault present but not
configured : Coherence fault
9699 Row 2 left and right pretensioners in series fault present but not
configured : Coherence fault
969A Row 3 left and right pretensioners in series fault present but not
configured : Coherence fault
969B Passenger's strap return pretensioner fault present but not configured :
Coherence fault
969B Fault in the front RH seat belt pretensioner: present but not configured :
Coherence fault
969C Rear left roll-over bar fault : Coherence fault
969D Rear right roll-over bar fault : Coherence fault
969F Row 1 central pretensioner fault present but not configured : Coherence fault
A601 Level 1 driver's airbag ignition module fault : Short circuit to positive
A602 Level 2 driver's airbag ignition module fault : Short circuit to positive
A603 Level 1 passenger airbag ignition module fault : Short circuit to positive
A604 Level 2 passenger airbag ignition module fault : Short circuit to positive
A605 Driver's pretensioner fault : Short circuit to positive
A606 Passenger's pretensioner fault : Short circuit to positive
A607 Front left side airbag ignition module fault : Short circuit to positive
A608 Front right side airbag ignition module fault : Short circuit to positive
A609 Rear left side airbag ignition module fault : Short circuit to positive
A60A Rear right side airbag ignition module fault : Short circuit to positive
A60B Left hand curtain airbag igniter fault : Short circuit to positive
A60C Right-hand side curtain airbag ignition module fault : Short circuit to
positive
A60D Driver's knee airbag ignition module fault : Short circuit to positive
A60E Passenger's knee airbag ignition module fault : Short circuit to positive
A610 Front left satellite fault : Short circuit to positive
A611 Front right satellite fault : Short circuit to positive
A612 Rear left satellite fault : Short circuit to positive
A613 Rear right satellite fault : Short circuit to positive
A614 Front left satellite fault : Short circuit to positive
A615 Front right satellite fault : Short circuit to positive
A616 Front left door satellite (additional) fault : Short circuit to positive
A617 Front right door satellite (additional) fault : Short circuit to positive
A660 Fault with the passenger airbag deactivation switch : Short circuit to
positive
A665 Driver's seat position sensor fault : Short circuit to positive
A666 Passenger seat position sensor fault : Short circuit to positive
A670 Fault in driver's anti-submarining airbag : Short circuit to positive
A671 Fault in passenger's anti-submarining airbag : Short circuit to positive
A675 Fault on the LH front and rear lateral airbag igniters in series : Short
circuit to positive
A676 Fault on the RH front and rear lateral airbag igniters in series : Short
circuit to positive
A677 Driver's strap return pretensioner fault : Short circuit to positive
A677 Fault in the front LH seat belt pretensioner : Short circuit to positive
A690 Left-hand side airbag and left-hand side curtain airbag in series ignition
modules fault : Short circuit to positive
A691 Right-hand side airbag and right-hand side curtain airbag in series ignition
modules fault : Short circuit to positive
A692 Fault on the LH row 1 and 2 pretensioners in series : Short circuit to
positive
A693 Fault on the RH row 1 and 2 pretensioners in series : Short circuit to
positive
A694 Fault on the LH row 2 and 3 pretensioners in series : Short circuit to
positive
A695 Fault on the RH row 2 and 3 pretensioners in series : Short circuit to
positive
A696 Row 2 central pretensioner fault : Short circuit to positive
A697 Row 3 central pretensioner fault : Short circuit to positive
A698 Driver and passenger pretensioners in series fault : Short circuit to positive
A699 Row 2 left and right pretensioners in series fault : Short circuit to positive
A69A Row 3 left and right pretensioners in series fault : Short circuit to positive
Fault Codes: ANTI DEPOLLUTION L5 (ENGINE) AND BVA AM6Fault codes (Summary)
C1325 Fault on the rear left wheel speed information not received by the CAN (Anti-
lock braking system ECU)
C1335 Fault on the rear right wheel speed information not received by the CAN
(Anti-lock braking system ECU)
P0115 Fault on the engine coolant temperature information not received by the CAN
(Engine ECU)
P0218 Fault: gearbox oil temperature too high (thermal protection pattern 3) with
request for reduction of engine torque
P0298 Fault: gearbox oil needs replacing
P0562 ECU supply voltage too low fault
P0563 ECU supply voltage too high fault
P0601 ECU fault
P0603 ECU fault
P0604 ECU fault
P0715 Fault on the automatic gearbox input speed sensor circuit : Coherence
P0717 Fault on the automatic gearbox input speed sensor circuit : No signal
P0720 Fault on the automatic gearbox output speed sensor circuit : Coherence
P0722 Fault on the automatic gearbox output speed sensor circuit : No signal
P0727 Fault on the engine speed information not received by the CAN (Engine ECU)
P0729 Mechanical or hydraulic fault on the sixth gear : Coherence
P0731 Mechanical or hydraulic fault on the first gear : Coherence
P0732 Mechanical or hydraulic fault on the second gear : Coherence
P0733 Mechanical or hydraulic fault on the third gear : Coherence
P0734 Mechanical or hydraulic fault on the fourth gear : Coherence
P0735 Mechanical or hydraulic fault on the fifth gear : Coherence
P0736 Mechanical or hydraulic fault on the reverse gear : Coherence
P0741 Fault: converter lock-up impossible
P0742 Fault: torque converter permanently locked-up
P0765 General fault on the reduction of drag in mode D (neutral)
P0771 Unwanted change to neutral in mode D or R detection fault (automatic gearbox
mechanical or hydraulic fault)
P0772 Fault in engaging clutch C1 for reduction of drag in mode D (Neutral)
P0780 Fault: random gear changing : Coherence
P0819 Press control signal fault : Change of position impossible
P0826 Press control signal fault : Stuck in M+ or M-
P0928 Fault on the lever locking actuator circuit (shift-lock) : Short circuit to
positive
P0930 Fault on the lever locking actuator circuit (shift-lock) : Short circuit to
earth or open circuit
P0938 Automatic gearbox oil temperature blocked at the same value fault
(Information from the sensor) : Coherence
P0939 Fault on the automatic gearbox oil temperature sensor circuit : Short circuit
to earth
P0940 Fault on the automatic gearbox oil temperature sensor circuit : Short circuit
to positive or open circuit
P0961 SLT solenoid locking fault : Locking
P0962 Fault on the circuit of the 'SLT' solenoid valve (Regulation of the line
pressure) : Short circuit to earth or open circuit
P0963 Fault on the circuit of the 'SLT' solenoid valve (Regulation of the line
pressure) : Short circuit to positive
P0965 SLB1 solenoid locking fault (Gear shift control) : Locking
P0966 Fault on the control circuit of the 'SLB1' solenoid valve (Gear control) :
Short circuit to earth or open circuit
P0967 Fault on the control circuit of the 'SLB1' solenoid valve (Gear control) :
Short circuit to positive
P0969 SLC1 solenoid locking fault (Gear shift control) : Locking
P0970 Fault on the control circuit of the 'SLC1' solenoid valve (Gear control) :
Short circuit to earth or open circuit
P0971 Fault on the control circuit of the 'SLC1' solenoid valve (Gear control) :
Short circuit to positive
P0973 Fault on the circuit of the 'S1' solenoid valve (Control of the engine brake)
: Short circuit to earth
P0974 Fault on the circuit of the 'S1' solenoid valve (Control of the engine brake)
: Short circuit to positive or open circuit
P0976 Fault on the circuit of the 'S2' solenoid valve (Control of the engine brake)
: Short circuit to earth
P0977 Fault on the circuit of the 'S2' solenoid valve (Control of the engine brake)
: Short circuit to positive or open circuit
P1605 Engine torque required by the driver information not received by the CAN
fault (Engine ECU)
P1613 Configuration not carried out fault
P1703 Fault on the accelerator pedal position information not received by the CAN
(Engine ECU)
P1727 Fault on the actual engine torque information not received by the CAN (Engine
ECU)
P1732 Fault on the gear selector position sensor (Incorporated in the automatic
gearbox ECU) : Low stop
P1733 Fault on the gear selector position sensor (Incorporated in the automatic
gearbox ECU) : Coherence
P1737 Fault on the gear selector position sensor (Incorporated in the automatic
gearbox ECU) : High stop
P1771 Exit from the 'Reduction of drag' in mode D operating mode fault (neutral)
P1828 Fault on the starting inhibiting control output (Start-lock) : Short circuit
to positive
P1829 Fault on the starting inhibiting control output (Start-lock) : Short circuit
to earth or open circuit
P1830 Front wheels speed not received by the CAN information fault (Anti-lock brake
control unit)
P1838 Mechanical or hydraulic fault on the engine brake function in the first
sequential mode : Coherence
P1839 Reduction of drag in mode D activation fault (neutral)
P2719 SLC2 solenoid locking fault (Gear shift control) : Locking
P2720 Fault on the solenoid valve SLC2 control circuit (Gear shift control) : Short
circuit to earth or open circuit
P2721 Fault on the solenoid valve SLC2 control circuit (Gear shift control) : Short
circuit to positive
P2728 SLC3 solenoid locking fault (Gear shift control) : Locking
P2729 Fault on the control circuit of the 'SLC3' solenoid valve (Gear control) :
Short circuit to earth or open circuit
P2730 Fault on the control circuit of the 'SLC3' solenoid valve (Gear control) :
Short circuit to positive
P2762 'SLU' solenoid locking fault (Control of the converter or lock-up) : Locking
P2763 Fault on the control circuit of the 'SLU' solenoid valve (Control of the
converter or lock-up) : Short circuit to positive
P2764 Fault on the control circuit of the 'SLU' solenoid valve (Control of the
converter or lock-up) : Short circuit to earth or open circuit
P2775 Fault in the sequential signal + or the sensor : Coherence
P2776 Fault in the sequential signal + or the sensor : Short circuit to earth
P2777 Fault in the sequential signal + or the sensor : Short circuit to positive or
open circuit
P2779 Fault in the one-touch signal : Coherence
P2780 Fault in the one-touch signal : Short circuit to earth
P2781 Fault in the one-touch signal : Short circuit to positive or open circuit
U1000 Communication fault on the CAN between the automatic gearbox ECU and the
other ECUs of the network
U1003 Fault: CAN
U1105 Fault: absence of communication with the steering wheel angle sensor
U1108 Fault in communication on the CAN with the engine management ECU
U1110 Fault in communication with the automatic gearbox electric control ECU
U1113 Fault in communication on the CAN with the ESP ECU
U1118 Fault in communication with the BSI on the CAN
U1205 Fault in the steering wheel angle information received by the CAN : Value
received incorrect
U1208 Fault in the information transmitted by the engine ECU : Value received
incorrect
U1213 Fault in the information transmitted by the dynamic stability control (ESP)
ECU : Value received incorrect
U1218 Fault in the engine oil or intake air temperature information received by the
CAN (Engine ECU) : Value received incorrect
U1310 Automatic gearbox electric control fault
U2000 Fault in synchronisation of the main controlled triggering request received
by the CAN (BSI ECU) and the wire command for controlled triggering
U2003 Coherence fault between the status of the vehicle and the main controlled
triggering request received by the CAN
U2109 Fault in synchronisation of the partial controlled triggering request
received by the CAN (BSI ECU) and the wire command for controlled triggering
C1325 Fault in communication on the CAN with the ABS/ESP ECU : Value received
incorrect (Rear left-hand wheel)
C1335 Fault in communication on the CAN with the ABS/ESP ECU : Value received
incorrect (Rear right-hand wheel)
P0115 Engine coolant temperature signal fault : Value received incorrect
P0218 Oil temperature warning light fault : The indicator light comes on(Thermal
protection pattern 3) : Engine torque reduction request
P0298 Oil wear counter fault : Value at upper limit
P0562 Battery voltage fault : Voltage too low
P0563 Battery voltage fault : Voltage too high
P0601 ECU fault : Processor
P0602 Telecharging fault
P0603 ECU fault : EEPROM
P0604 ECU fault : RAM
P0605 ECU fault : Flash ROM
P0715 Fault on the gearbox input speed sensor circuit : Value received incorrect
P0717 Fault on the gearbox input speed sensor circuit : No signal
P0720 Fault on the gearbox output speed sensor circuit : Value received incorrect
P0722 Fault on the gearbox output speed sensor circuit : No signal
P0727 Engine speed fault : Value received incorrect
P0729 Gearbox mechanical or hydraulic fault : Coherence on 6th gear
P0731 Gearbox mechanical or hydraulic fault : Coherence on first gear
P0732 Gearbox mechanical or hydraulic fault : Coherence in 2nd gear
P0733 Gearbox mechanical or hydraulic fault : Coherence in 3rd gear
P0734 Gearbox mechanical or hydraulic fault : Coherence in 4th gear
P0735 Gearbox mechanical or hydraulic fault : Coherence in 5th gear
P0736 Gearbox mechanical or hydraulic fault : Coherence on reverse gear
P0741 Converter lock-up fault : Lock-up impossible
P0742 Converter lock-up fault : Permanent lock-up
P0751 Mechanical or hydraulic fault on 1st gear with engine brake : Coherence
P0752 Mechanical or hydraulic fault on 1st gear : Coherence
P0756 Mechanical or hydraulic fault on 2nd gear : Coherence
P0761 Mechanical or hydraulic fault on the third gear : Coherence
P0765 Fault: detection of neutral complete (In 'D' mode)
P0766 Mechanical or hydraulic fault on the fourth gear : Coherence
P0771 Mechanical or hydraulic fault on the fifth gear : Coherence
P0772 Fault in engaging clutch C1 for reduction of drag in mode D
P0780 Fault: random gear changing : Coherence
P0819 Press control signal fault : Locking
P0826 Press control signal fault : Locking in position M+ or M-
P0882 Gearbox ECU supply voltage fault : Voltage too low
P0883 Gearbox ECU supply voltage fault : Voltage too high
P0928 Fault on the lever locking actuator circuit (shift-lock) : Open circuit or
short circuit to earth
P0931 Fault on the lever locking actuator circuit (shift-lock) : Short circuit to
positive
P0938 Oil thermistor fault : High stop
P0939 Oil thermistor fault : Short circuit to earth
P0940 Oil thermistor fault : Open circuit or short circuit to the plus
P0961 Line pressure modulation electrovalve output fault : Coherence
P0962 Fault on the line pressure modulation electrovalve circuit : Open circuit or
short circuit to earth
P0963 Fault on the line pressure modulation electrovalve circuit : Short circuit to
positive
P0965 Brake pressure modulation electrovalve output fault (SLB1 : Coherence
P0966 Fault on the control circuit of the brake pressure modulation electrovalve
(SLB1) : Open circuit or short circuit to earth
P0967 Fault on the control circuit of the brake pressure modulation electrovalve
(SLB1) : Short circuit to positive
P0969 Clutch pressure modulation solenoid valve (SLC1) output fault : Coherence
P0970 Fault on the control circuit of the clutch pressure modulation electrovalve
(SLC1) : Open circuit or short circuit to earth
P0971 Fault on the control circuit of the clutch pressure modulation electrovalve
(SLC1) : Short circuit to positive
P0973 Fault on the solenoid circuit of sequence S1 : Short circuit to earth
P0974 Fault on the solenoid circuit of sequence S1 : Open circuit or short circuit
to the plus
P0976 Fault on the solenoid circuit of sequence S2 : Short circuit to earth
P0977 Fault on the solenoid circuit of sequence S2 : Open circuit or short circuit
to the plus
P1605 Fault in the information on torque requested by the driver sent by the engine
ECU : Value received incorrect
P160A ECU identification fault
P160E Supply cut-off during the powerlatch fault
P1613 Configuration fault
P1703 Fault in the accelerator pedal position information transmitted by the engine
management ECU : Value received incorrect
P1727 Fault in the actual engine torque information transmitted by the engine
management ECU : Value received incorrect
P1732 Fault on the gear lever position sensor : No signal
P1733 Fault on the gear lever position sensor : Coherence
P1737 Fault on the gear lever position sensor : Value received incorrect
P1771 Reduction of drag in D mode fault : Racing of the engine
P17A0 Fault on the key locking control circuit (key lock) : Open circuit or short
circuit to the plus
P17A1 Fault on the key locking control circuit (key lock) : Short circuit to earth
P17A2 Mechanical or hydraulic fault on reverse gear : Coherence
P17A3 Neutral detection fault (in mode R)
P17A5 Mechanical or hydraulic fault on 1st gear with engine brake : Coherence
P17A9 Neutral detection fault (in mode D)
P17AA Reduction of drag in D mode fault : Engaging of C1
P1800 Position N programming fault
P1828 Fault on the start lock control output : Short circuit to positive
P1829 Fault on the start lock control output : Open circuit or short circuit to
earth
P1830 Fault in the front wheels average speed information transmitted by ABS/ESP :
Value received incorrect
P1838 Gearbox mechanical or hydraulic fault : Coherence in first gear with engine
brake
P1839 Reduction of drag in mode D activation fault : No check
P2707 Mechanical or hydraulic fault on 6th gear : Coherence
P2719 Clutch pressure modulation solenoid valve SLC2 output fault : Coherence
P2720 Fault on the control circuit of the clutch pressure modulation electrovalve
SLC2 : Short circuit to earth or open circuit
P2721 Fault on the control circuit of the clutch pressure modulation electrovalve
SLC2 : Short circuit to positive
P2728 Clutch pressure modulation solenoid valve SLC3 output fault : Coherence
P2729 Fault on the control circuit of the clutch pressure modulation electrovalve
SLC3 : Open circuit or short circuit to earth
P2730 Fault on the control circuit of the clutch pressure modulation electrovalve
SLC3 : Short circuit to positive
P2762 Torque converter lock-up pressure modulation electrovalve output fault :
Coherence
P2763 Faults in the control circuit of the lock-up pressure modulation solenoid
valve of the SLU converter : Short circuit to positive
P2764 Faults in the control circuit of the lock-up pressure modulation solenoid
valve of the SLU converter : Open circuit or short circuit to earth
P2775 Fault in the one-touch signal+ : Value received incorrect
P2776 Fault in the one-touch signal+ : Short circuit to earth
P2777 Fault in the one-touch signal+ : Open circuit or short circuit to the plus
P2779 Fault in the one-touch signal - : Value received incorrect
P2780 Fault in the one-touch signal - : Short circuit to earth
P2781 Fault in the one-touch signal - : Open circuit or short circuit to the plus
U1000 Communication fault on the CAN between the automatic gearbox ECU and the
other ECUs of the network : No signal
U1003 CAN communication fault : No signal
U1105 Fault in communication on the CAN network with the steering wheel angle
sensor : No signal
U1108 Fault in communication on the CAN with the engine management ECU : No signal
U1110 Fault in communication on the CAN with the automatic gearbox electric control
ECU : No signal
U1113 Fault in communication on the CAN with the ABS/ESP ECU : No signal
U1118 Fault in communication on the CAN with the built-in systems interface(BSI) :
No signal
U1205 Fault in the information received by the steering wheel angle sensor over the
CAN network : Value received incorrect
U1208 Fault in the information sent by the engine management ECU over the CAN
network : Value received incorrect
U1213 Fault in the information transmitted by the ABS/ESP ECU on the CAN network :
Value received incorrect
U1218 Fault in the outside air temperature received on the CAN network (Engine ECU)
: Value received incorrect
U1308 Fault in communication with the engine ECU on the CAN network : No signal
U1310 Fault in communication of the gearbox electric control on the CAN : Value
received incorrect or not received
U1313 Fault in communication with the ABS/ESP ECU on the CAN : No signal
U1318 Fault in communication with the built-in systems interface on the CAN : No
signal
U2000 Fault in receipt of the main triggering request information received on the
CAN : Absence of signal or value received incorrect
U2003 Fault in receipt of the controlled main triggering request information
received on the CAN : Coherence
7007 Fault in the transmission of the partial triggering status on the CAN I/S
(Inter-system)
710A Fault: consistency between the control panel ECU and the multifunction display
ECU for management of the customisation menu
7117 Presence of water in diesel fault
7150 Vehicle speed information fault
7151 Engine speed data fault
7153 Vehicle longitudinal acceleration information fault
7155 Coolant temperature data fault
7157 Outside air temperature information fault
715C Cooling pressure information fault:
7173 Oil temperature sensor information fault
717C Gross fuel level information fault
717D Fuel level information fault
71AF Information sent by the Stop And Start ECU invalid fault
93FF Seat belts not fastened display fault: Incorrect display : Coherence
9520 Fault in coherence between the speed limiter or cruise control and the engine
ECU : Coherence
9521 Fault: jamming of the speed limiter or cruise control switch : Coherence
9522 Fault: saturation of the log of faults (Too many fault events recorded at the
same time : These events temporarily ignored) : Coherence
9527 Engine immobiliser: transponder recognised but engine ECU locked : Coherence
9528 Fault: absence of command of the starter : Coherence
9529 Fault: engine stopped while driving : Coherence
952B Fault: voltage provided by the alternator insufficient : Coherence
9562 Fault in the difference in supply voltage between the BSI and the ABS/ESP or
the BSI and the battery charge status unit : Coherence
A008 Remote triggering wire (RCD) fault : Short circuit to positive
A4A1 Interior lamp lighting fault (Before /Rear ) : Short circuit to positive
A4A5 Right-hand direction indicators lighting fault : Short circuit to positive
A4A6 Left-hand direction indicator illumination fault : Short circuit to positive
A4A7 Number plate lighting fault : Short circuit to positive
A4A9 Rear screen opening command fault : Short circuit to positive
A4AA Fault in the heated rear window control : Short circuit to positive
A4AB Cooling fan assembly control fault : Short circuit to positive
A4AC Footwells lighting fault : Short circuit to positive
A4AE Doors and tailgate locking fault : Short circuit to positive
A4BB Fault: vehicle protection status LED : Short circuit to positive
A4BC Rear right indicator lighting fault : Short circuit to positive
A4BD Rear left indicator lighting fault : Short circuit to positive
A4BE Rear right stoplamp lighting fault : Short circuit to positive
A4BF Rear left stoplamp lighting fault : Short circuit to positive
A4C0 Rear right sidelamp lighting fault : Short circuit to positive
A4C1 Rear left sidelamp lighting fault : Short circuit to positive
A4C5 Third stoplamp lighting fault : Short circuit to positive
A4C7 Right-hand reversing lamp lighting fault : Short circuit to positive
A4C8 Left-hand reversing lamp lighting fault : Short circuit to positive
A4C9 Fault: illumination of the rear RH fog lamp : Short circuit to positive
A4CA Fault: illumination of the rear LH fog lamp : Short circuit to positive
A4D3 Front door sills lighting fault : Short circuit to positive
A4D4 Rear door sills or boot lighting fault : Short circuit to positive
A4D6 Fascia lighting fault : Short circuit to positive
A4D7 Exterior lateral lighting fault : Short circuit to positive
A4D8 Buttons lighting fault : Short circuit to positive
A4D8 Fault: rear LH one-touch electric window raise control : Short circuit to
positive
A4D9 Boot opening control fault : Short circuit to positive
A4DA Rear sequential windows prohibition control fault : Short circuit to positive
A4DC Fault: rear LH one-touch electric window lower control : Short circuit to
positive
A4DD Fault: rear RH one-touch electric window raise control : Short circuit to
positive
A4DE Fault: rear RH one-touch electric window lower control : Short circuit to
positive
A4DF Front one-touch electric window fault : Short circuit to positive
A4E0 Electrochromic rear view mirror supply fault : Short circuit to positive
A4E1 Fault: 12V supply output or cigar lighter : Short circuit to positive
A4E2 CAN+ output fault : Short circuit to positive
A4E3 Fault: rear wiper control : Short circuit to positive
A4E4 Engine running information output fault (Main) : Short circuit to positive
A4E5 Engine running information output fault (Secondary) : Short circuit to
positive
A4E6 Fault: suspension SPORT LED lighting : Short circuit to positive
A4E7 'stop and start' warning lamp lighting fault : Short circuit to positive
A4E8 Fault: ESP LED lighting : Short circuit to positive
A4E9 Front right daytime lamp lighting fault : Short circuit to positive
A4EA Front left daytime lamp lighting fault : Short circuit to positive
A4EB Additional sidelamps lighting fault : Short circuit to positive
A4EC Doors and tailgate unlocking fault : Short circuit to positive
A4ED Driver's door unlocking fault : Short circuit to positive
A4EE Front doors deadlocking fault : Short circuit to positive
A4EF Rear doors deadlocking fault : Short circuit to positive
A4F0 Sunroof control fault : Short circuit to positive
A4F3 Striker actuator fault (Right-hand door) : Short circuit to positive
A4F6 Striker actuator fault (Left-hand door) : Short circuit to positive
A9AD Heater matrix pump relay fault : Short circuit to positive
B008 Remote triggering wire (RCD) fault : Short circuit to earth
B403 Fuel gauge signal fault : Short circuit to earth
B404 Engine oil temperature sensor fault : Short circuit to earth
B40B Stop and Start button fault (Button locked in pressed status or signal wire in
short- circuit to earth) : Short circuit to earth
B40E Alarm button fault (Button jammed in or signal wire short circuit to earth) :
Short circuit to earth
B412 Sliding side door contact switch fault, On the right-hand side : Short circuit
to earth
B413 Sliding side door contact switch fault, On the left-hand side : Short circuit
to earth
B415 Outside temperature sensor circuit fault : Short circuit to earth
B4A1 Interior lamp lighting fault (Before /Rear ) : Short circuit to earth
B4A3 Hazard warning lamps switch warning lamp output fault : Short circuit to earth
AED6 Fault on the audio outputs of the CD changer : Short circuit to positive
BED6 Fault on the audio outputs of the CD changer : Short circuit to earth
F003 Fault absence of communication with the built-in systems interface
F00A CAN network fault
F00F ECU not communicating on the CAN fault
F062 Fault - absence of communication with the audio system or the telematic unit
FED0 Fault on one of the buttons of the CD changer (Button jammed)
FED4 CD changer left-hand audio output fault
FED5 CD changer right-hand audio output fault
FEDC CD changer mechanical operation fault
Fault codes - Computer ESP BOSCH 8.1 ELECTRONIC STABILITY PROGRAM (Sunmmary)
C0040 Brake pedal switch fault : Coherence with the pressure sensor
C1135 Steering wheel angle sensor fault : internal fault
C1136 Steering wheel angle sensor fault : Coherence
C1137 Steering wheel angle sensor fault : Coherence
C119D Fault: loss of ASR+ selector communication
C119E ASR+ selector fault without loss of communication
C1301 Incoherence between the brake light switch and the pressure sensor
C1302 Braking pressure sensor signal fault : Open circuit, short circuit to
positive, short circuit to earth
C1310 Yaw sensor signal fault : internal fault
C1311 Yaw sensor signal fault : Coherence
C1315 Transverse acceleration sensor signal fault : internal fault
C1316 Transverse acceleration sensor signal fault : Coherence
C1320 Front LH wheel speed sensor signal fault : Open circuit, short circuit to
positive, short circuit to earth
C1321 Front LH wheel speed sensor signal fault : Coherence
C1325 Rear LH wheel speed sensor signal fault : Open circuit, short circuit to
positive, short circuit to earth
C1326 Rear LH wheel speed sensor signal fault : Coherence
C1330 Front right wheel speed sensor signal fault : Open circuit, short circuit to
positive, short circuit to earth
C1331 Front right wheel speed sensor signal fault : Coherence
C1335 Rear right wheel speed sensor signal fault : Open circuit, short circuit to
positive, short circuit to earth
C1336 Rear right wheel speed sensor signal fault : Coherence
C1341 Rear LH inlet electrovalve fault
C1343 Rear LH exhaust electrovalve fault
C1346 Rear right inlet electrovalve fault
C1348 Rear right exhaust electrovalve fault
C1351 Front LH inlet electrovalve fault
C1353 Front LH exhaust electrovalve fault
C1356 Front right inlet electrovalve fault
C1358 Front right exhaust electrovalve fault
C1362 Switching electrovalve 1 fault
C1367 Switching electrovalve 2 fault
C1372 Limiting electrovalve 1 fault
C1377 Limiting electrovalve 2 fault
C1380 Recirculation pump supply fault : Mechanical blockage
C1381 Recirculation pump supply fault : Open circuit, short circuit to positive,
short circuit to earth
C1383 Brake fluid level information fault : Open circuit, short circuit to
positive, short circuit to earth
C1384 Stop lamps switch signal fault : Coherence
C1385 Solenoid valves supply voltage fault
C1387 Wheel speed sensor dormant fault : Coherence
C1388 Fault: steering wheel angle sensor cannot be calibrated : Calibration
C1389 Brake fluid level information fault : Open circuit, short circuit to
positive, short circuit to earth
C1391 Non-acknowledgement of the engine torque fault
C1392 Dynamic stability control (ESP) ECU system fault
C1396 Clutch pedal sensor signal fault : Coherence
C1398 Configuration fault (Configuration of the vehicle incorrect) : Coherence
C139A Electrically controlled parking brake (FSE) automatic trigger fault : Reverse
gear detection incorrect : Coherence
C139B Gyrometer-accelerometer sensor signal fault : Open circuit, short circuit to
positive, short circuit to earth
C139C Clutch pedal sensor calibration fault : Calibration not carried out
C139D Longitudinal acceleration sensor calibration fault : Calibration
C139F Clutch pedal sensor signal fault : Open circuit, short circuit to positive,
short circuit to earth
C13A1 Clutch pedal sensor signal fault : Open circuit, short circuit to positive,
short circuit to earth
C13A2 Clutch pedal sensor signal fault : Coherence
C1502 Longitudinal acceleration sensor signal fault : internal fault
C1503 Longitudinal acceleration sensor signal fault : Coherence
C1510 CAN network fault
C155D Automatic application function inhibited fault
F019 Fault - absence of communication with the suspension ECU (Integrated hydraulic
unit)
F01C Fault: absence of communication with the ESP ECU
F01D Fault - absence of communication with the suspension ECU
F041 Fault - absence of communication with the rear reference height corrector or
pneumatic suspension ECU
F042 Fault - absence of communication with the automatic gearbox electric control
ECU
P0562 ECU supply low voltage fault
P0563 ECU supply over-voltage fault
P0602 Download fault
P0606 ECU fault
P1613 Configuration fault (Absence of configuration)
U1000 Mute ECU fault
U1003 General CAN fault
U1105 Fault: absence of communication with the steering wheel angle sensor : No
signal
U1108 No communication with the engine management ECU fault : No signal
U1109 Fault: absence of communication with the automatic gearbox ECU : No signal
U1110 Fault - absence of communication with the automatic gearbox electric control
ECU : No signal
U1117 Fault no communication with the intelligent hydraulic unit ECU : No signal
U1118 Fault absence of communication with the built-in systems interface : No
signal
U1119 Electrically controlled parking brake (FSE) automatic trigger fault : No
signal
U1124 Fault: absence of communication with the pneumatic suspension ECU : No signal
U1217 Fault no communication with the intelligent hydraulic unit ECU : Data invalid
U1218 Fault absence of communication with the built-in systems interface : Data
invalid
U1219 Electrically controlled parking brake (FSE) automatic trigger fault : Data
invalid
U1224 Fault: absence of communication with the pneumatic suspension ECU : Data
invalid
U1225 Fault: absence of communication with the gyrometer-accelerometer sensor :
Data invalid
U1305 Fault: absence of communication with the steering wheel angle sensor : No
signal
U1308 No communication with the engine management ECU fault : No signal
U1309 Fault: absence of communication with the automatic gearbox ECU : No signal
U1310 Fault - absence of communication with the automatic gearbox electric control
ECU : No signal
U1317 Fault no communication with the intelligent hydraulic unit ECU : No signal
U1318 Fault absence of communication with the built-in systems interface : No
signal
U1319 Electrically controlled parking brake (FSE) automatic trigger fault : No
signal
U131D ASR+ selector signal fault : No signal
U1324 Fault: absence of communication with the pneumatic suspension ECU : No signal
Fault codes - Computer ESP trw EBC440 ELECTRONIC STABILITY PROGRAM (Summary)
C1600 RH low frequency aerial fault : Short circuit to earth or short circuit to
positive
C1601 LH low frequency aerial fault : Short circuit to earth or short circuit to
positive
C1602 Fault: front LH wheel transmitter module information : Value received
incorrect
C1603 Fault: front RH wheel transmitter module information : No signal
C1604 Fault: rear LH wheel transmitter module information : No signal
C1605 Fault: rear RH wheel transmitter module information : No signal
C1606 Spare wheel valve absent fault
C1608 Front left valve battery flat fault
C1609 Front right valve battery flat fault
C1610 Rear right valve battery flat fault
C1611 Rear left valve battery flat fault
C1612 High frequency remote control fault
C1613 Front Left Wheel locating fault
C1614 Front Right Wheel locating fault
C1615 Rear Left Wheel locating fault
C1616 Rear Right Wheel locating fault
C1617 Spare wheel transmitter module battery flat
P0562 Supply voltage too low : Low stop
P0563 Supply voltage : High stop
P0602 ECU blank or downloading defective
P0603 ECU fault
P0605 ECU fault
P0606 ECU fault
P1607 No wheel transmitter module programmed in the tyre under-inflation detection
receiver : Learning
U1000 Communication fault on the CAN network
U1003 Communication fault on the CAN network
U1105 Absence of communication on the CAN with the steering wheel angle sensor
U1108 Absence of communication on the CAN with the engine management ECU
U1113 Absence of communication on the CAN with the ABS/ESP ECU
U1116 Absence of communication on the CAN with the suspension ECU
U1118 Absence of communication with the BSI on the CAN : No OK
U1205 Fault: steering wheel angle information : Value received incorrect
U1208 Engine speed data fault : Value received incorrect
U1213 Vehicle speed data fault : Value received incorrect
U2116 Fault in the information received by the CAN from the suspension ECU : Value
received incorrect
U2118 BSI clearing of the high frequency control reawakening fault : Value received
incorrect
U2000 Fault: reception of principal wake-up status
U2002 RCD fault : Controlled wake-up line short circuit to earth : Short circuit to
earth
U2003 Fault: incoherence of principal wake-up
U2005 RCD fault: Vehicle speed information fault (absent or not valid)
U2006 RCD fault: Engine speed information fault (absent or not valid)
U2215 RCD fault: Partial reawakening request fault following a high frequency
remote control command (Japan) : No OK
P0001 Fuel flow regulator control : Regulation electrovalve in open circuit or ECU
connection temperature too high
P0002 Fuel flow regulator control : Lack of coherence of the control current
P0003 Fuel flow regulator control : Regulation electrovalve short circuited to
earth or value too low
P0004 Fuel flow regulator control : Regulation electrovalve short circuited to
positive (blocked closed)
P0016 Camshaft signal : Crankshaft-camshaft synchronisation
P0026 Recirculation valve solenoid valve control : Temperature excessive
P0030 Lambda sensor signal : Voltage problem on the sensor heating power stage
P0031 Lambda sensor signal : Short circuit to earth on the sensor heating power
stage
P0032 Lambda sensor signal : Short circuit to positive on the sensor heating power
stage
P0033 Compressor valve 2 compressor solenoid valve control 2 : Open circuit.
Compressor valve 2 closed
P0034 Compressor valve 2 compressor solenoid valve control 2 : Short circuit to
earth. Compressor valve 2 open
P0035 Compressor valve 2 compressor solenoid valve control 2 : Short circuit to
positive. Compressor valve 2 closed
P0039 Compressor valve 2 compressor solenoid valve control 2 : Temperature
excessive
P0049 Turbo pressure regulation : Biturbo mode impossible, risk of overspeed on
turbo 2
P0053 Lambda sensor signal : Internal resistance fault
P0069 Atmospheric pressure signal : Coherence in relation to the inlet pressure
P0075 Recirculation valve solenoid valve control : Open circuit. Min turbocharging
P0076 Recirculation valve solenoid valve control : Short circuit to earth. Max
turbocharging
P0077 Recirculation valve solenoid valve control : Short circuit to positive. Min
turbocharging
P0087 Fuel pressure regulator control : Pressure below reference value
P0087 Fuel high pressure regulation : Pressure below reference value
P0088 Fuel high pressure regulation : Pump flow regulation solenoid valve opens
more than the reference value
P0089 Fuel pressure regulator control : Regulator control current not coherent in
relation to the pressure
P0090 Fuel pressure regulator control : Open circuit
P0091 Fuel pressure regulator control : Short circuit to earth
P0092 Fuel pressure regulator control : Short circuit to positive
P0093 Fuel high pressure regulation : Pump flow regulation solenoid valve opens
less than the reference value
P0097 Intake air temperature signal (Intake air manifold) : Short circuit to earth
or value too low
P0098 Intake air temperature signal (Intake air manifold) : Short circuit to
positive or open circuit or value too high
P0100 Flowmeter signal : Air flow not plausible
P0102 Flowmeter signal : Frequency too high : Min air flow
P0103 Flowmeter signal : Frequency too low : Maximum air flow
P0104 Flowmeter signal : Sensor supply or signal open circuit, short circuit to
positive or to earth
P0107 Atmospheric pressure signal : Sensor incorporated in the ECU short circuit to
earth or value too low
P0108 Atmospheric pressure signal : Sensor incorporated in the ECU short circuit to
positive or open circuit or value too high
P0112 Intake air temperature signal (air flow sensor) : Short circuit to earth or
value too low
P0113 Intake air temperature signal (air flow sensor) : Short circuit to positive
or open circuit or value too high
P0115 Engine coolant temperature signal : Coherence of the temperature increase
P0117 Engine coolant temperature signal : Short circuit to earth or value too low
P0118 Engine coolant temperature signal : Short circuit to positive or open circuit
A99B Injection of air at the exhaust pump control fault : Short circuit to positive
A9A3 Lighting fault on the right-hand daytime light : Short circuit to positive
A9A8 Exhaust heat recovery system coolant pump control fault : Short circuit to
positive
A9AA Lighting fault on the left-hand static cornering light : Short circuit to
positive
A9AB Lighting fault on the right-hand static cornering light : Short circuit to
positive
A9AC Power supply fault on the variable valve lift system : Short circuit to
positive
A9B7 Fault in the ignition positive relay or in the output harness from the relay :
Short circuit to positive
A9B8 Power latch relay fault : Short circuit to positive
B98A Front right sidelamp fault : Short circuit to earth
B98B Front left sidelamp fault : Short circuit to earth
B98C Front right dipped beam headlamp fault : Short circuit to earth
B98D Front right dipped beam headlamp fault : Short circuit to earth
B98E Main beam headlamps fault : Short circuit to earth
B98F Front left foglamp fault : Short circuit to earth
B990 Front right foglamp fault : Short circuit to earth
B991 Front left direction indicator fault : Short circuit to earth
B992 Front right direction indicator fault : Short circuit to earth
B993 Front lights shutter control fault : Short circuit to earth
B994 Air conditioning compressor clutch control fault : Short circuit to earth
B995 Air conditioning compressor capacity control fault : Short circuit to earth
B996 Air conditioning blower control fault : Short circuit to earth
B997 Horns control fault : Short circuit to earth
B998 Headlamp wash control fault : Short circuit to earth
B99B Injection of air at the exhaust pump control fault : Short circuit to earth
B99C Fuel pump control fault : Short circuit to earth
B9A3 Lighting fault on the right-hand daytime light : Short circuit to earth
B9A8 Exhaust heat recovery system coolant pump control fault : Short circuit to
earth
B9AA Lighting fault on the left-hand static cornering light : Short circuit to
earth
B9AB Lighting fault on the right-hand static cornering light : Short circuit to
earth
B9AC Power supply fault on the variable valve lift system : Short circuit to earth
B9B7 Fault in the ignition positive relay or in the output harness from the relay :
Short circuit to earth
B9B8 Power latch relay fault : Short circuit to earth
C98A Front right sidelamp fault : Open circuit
C98B Front left sidelamp fault : Open circuit
C98F Front left foglamp fault : Open circuit
C990 Front right foglamp fault : Open circuit
C991 Front left direction indicator fault : Open circuit
C992 Front right direction indicator fault : Open circuit
C993 Front lights shutter control fault : Open circuit
C994 Air conditioning compressor clutch control fault : Open circuit
C995 Air conditioning compressor capacity control fault : Open circuit
C99B Injection of air at the exhaust pump control fault : Open circuit
C9A3 Lighting fault on the right-hand daytime light : Open circuit
C9A8 Exhaust heat recovery system coolant pump control fault : Open circuit
C9AA Lighting fault on the left-hand static cornering light : Open circuit
C9AB Lighting fault on the right-hand static cornering light : Open circuit
C9AC Power supply fault on the variable valve lift system : Open circuit
C9B8 Power latch relay fault : Open circuit
F000 Engine fuse box ECU not communicating on the CAN fault
F07A CAN network fault
F080 Fault: absence of communication with the BSI
F98A Front right sidelamp fault
F98B Front left sidelamp fault
F98C Front right dipped beam headlamp fault
F98D Front right dipped beam headlamp fault
F98E Main beam headlamps fault
F98F Front left foglamp fault
F990 Front right foglamp fault
F991 Front left direction indicator fault
F992 Front right direction indicator fault
F993 Front lights shutter control fault
F994 Air conditioning compressor clutch control fault
F995 Air conditioning compressor capacity control fault
F996 Air conditioning blower control fault
F997 Horns control fault
F998 Headlamp wash control fault
F99C Fuel pump control fault
F9A0 Starter control relay fault
F9AA Lighting fault on the left-hand static cornering light
F9AB Lighting fault on the right-hand static cornering light
P0328 Knock detector signal fault (Front row of cylinders) : Short circuit to
positive or open circuit
P0332 Knock detector signal fault (Rear row of cylinders) : Short circuit to earth
P0333 Knock detector signal fault (Rear row of cylinders) : Short circuit to
positive or open circuit
P0335 Engine speed sensor signal fault
P0336 Engine speed sensor signal fault : Coherence
P0337 Engine speed sensor signal fault : Short circuit to earth
P0338 Engine speed sensor signal fault : Short circuit to positive or open circuit
P0341 Cylinder reference sensor signal fault (Front row of cylinders) : Coherence
P0342 Cylinder reference sensor signal fault (Front row of cylinders) : Short
circuit to earth
P0343 Cylinder reference sensor signal fault (Front row of cylinders) : Short
circuit to positive or open circuit
P0346 Cylinder reference sensor signal fault (Rear row of cylinders) : Coherence
P0347 Cylinder reference sensor signal fault (Rear row of cylinders) : Short
circuit to earth
P0348 Cylinder reference sensor signal fault (Rear row of cylinders) : Short
circuit to positive or open circuit
P0350 Fault: control of ignition coils : Malfunction of the control of all of the
coils
P0351 Cylinder 1 ignition coil control fault : Electrical circuit malfunction
P0352 Cylinder 2 ignition coil control fault : Electrical circuit malfunction
P0353 Cylinder 3 ignition coil control fault : Electrical circuit malfunction
P0354 Cylinder 4 ignition coil control fault : Electrical circuit malfunction
P0355 Cylinder 5 ignition coil control fault : Electrical circuit malfunction
P0356 Cylinder 6 ignition coil control fault : Electrical circuit malfunction
P0410 Air injection into the exhaust fault
P0420 Catalytic converter ageing fault (Front row of cylinders)
P0430 Catalytic converter ageing fault (Rear row of cylinders)
P0443 Canister discharge electrovalve control fault : Coherence
P0444 Canister discharge electrovalve control fault : Open circuit
P0445 Canister discharge electrovalve control fault : Short circuit between two
wires
P0461 Fuel level sensor fault : Coherence or minimum fuel level reached
P0462 Fuel level sensor fault : Short circuit to earth
P0463 Fuel level sensor fault : Short circuit to positive or open circuit
P0475 Bimode exhaust valve electrovalve fault : Coherence
P0477 Bimode exhaust valve electrovalve fault : Short circuit to earth
P0478 Bimode exhaust valve electrovalve fault : Short circuit to positive or open
circuit
P0480 Fan (GMV1) high speed relay or chopper control: Electrical circuit
malfunction
P0481 Fan unit control GMV2 fault (Slow speed ) : Electrical circuit malfunction
P0485 Fan unit control fault : Coherence
P0501 Fault in the vehicle speed information received from the ABS/ESP : Absence of
frames
P0532 Air conditioning pressure sensor signal fault : Low stop
P0533 Air conditioning pressure sensor signal fault : High stop
P0560 Battery voltage fault
P0561 Battery voltage fault
P0562 Battery voltage fault : Low stop
P0563 Battery voltage fault : High stop
P0570 Fault on the cruise control / speed limiter : Coherence
P0571 Fault on the cruise control / speed limiter : Coherence
P0572 Fault on the cruise control / speed limiter : Coherence
P0573 Fault on the cruise control / speed limiter : Coherence
P0590 Fault on the cruise control / speed limiter : Coherence
P0591 Fault on the cruise control / speed limiter : Coherence
P0592 Fault on the cruise control / speed limiter : Coherence
P0593 Fault on the cruise control / speed limiter : Coherence
P0601 ECU internal fault
P0604 ECU internal fault
P0605 ECU internal fault
P0606 ECU internal fault
P0615 Starter control relay fault : Open circuit
P0616 Starter control relay fault : Short circuit to earth
P0617 Starter control relay fault : Short circuit to positive
P061B Engine management ECU monitoring fault
P0703 Principal brake and secondary brake information fault : Short circuit to
positive
P0704 Clutch switch signal fault : Coherence
P1152 Motorised throttle motor control fault : Open circuit, short circuit to
positive, short circuit to earth
P1153 Motorised throttle stops programming fault : Programming failure
P1157 Motorised throttle potentiometer track 2 fault : Low stop
P1158 Motorised throttle potentiometer track 2 fault : High stop
P1161 Throttle position regulation fault : Short-circuit to earth, short-circuit to
positive, coherence
P1303 Anti-knock regulation fault
P1329 Knock regulation limit fault on cylinder n? 1
P1330 Knock regulation limit fault on cylinder n? 2
P1331 Knock regulation limit fault on cylinder n? 3
P1332 Knock regulation limit fault on cylinder n? 4
P1333 Knock regulation limit fault on cylinder n? 5
P1334 Knock regulation limit fault on cylinder n? 6
P1335 Inlet camshaft position unknown fault (Front or rear bank of cylinders) :
Coherence
P1336 Combustion misfiring on unspecified cylinders fault
P1337 Fault: misfiring on cylinder No. 1
P1338 Fault: misfiring on cylinder No. 2
P1339 Fault: misfiring on cylinder No. 3
P1340 Fault: misfiring on cylinder No. 4
P1341 Fault: misfiring on cylinder No. 5
P1342 Fault: misfiring on cylinder No. 6
P1527 Alternator charge information fault
P1536 Principal brake and secondary brake information fault : Short circuit to
earth or open circuit
P1613 Configuration fault
P1614 Speed limiter point of resistance sensor signal fault : Coherence
P1621 Engine management ECU monitoring fault : ECU internal failure
P1622 Engine management ECU monitoring fault : ECU internal failure or fault at the
air loop
P1626 Engine management ECU monitoring fault : ECU internal failure
P1627 Engine management ECU monitoring fault : Accelerator pedal sensor signal
processing
P1632 Engine management ECU monitoring fault : ECU internal failure
P1643 Speed limiter point of resistance sensor signal fault : Short circuit to
earth
P1644 Speed limiter point of resistance sensor signal fault : Short circuit to
positive
P1645 Speed limiter point of resistance sensor signal fault : Lack of coherence
between the speed limiter point of resistance sensor signal and the accelerator
pedal position signal
P1652 Engine management ECU monitoring fault : Malfunction of the VVT system or
fault at the air loop
P1653 Engine management ECU monitoring fault
P1654 Engine management ECU monitoring fault : Motorised throttle signal processing
P1664 Engine management ECU monitoring fault : Processing of the engine torque
information
P1667 Engine management ECU monitoring fault : Accelerator pedal sensor signal
processing
P1669 Engine management ECU monitoring fault : Processing of the engine speed
information
P1693 Controlled engine starting and stopping reception anomaly fault : Absence of
frames
P1694 Fault: piloted engine stop-and-start (DAMP) : Coherence
P1695 Fault: piloted engine stop-and-start (DAMP) : Internal combustion engine
jammed
P1696 Fault: piloted engine stop-and-start (DAMP) : Coherence
P1701 Gear not coherent fault
P1739 Starter power stage fault : Short circuit to earth
P1740 Starter power stage fault : Short circuit to positive
P1741 Starter power stage fault : Open circuit
P2096 Downstrean oxygen sensor signal fault (Front pre-catalyst) : Ageing
P2097 Downstrean oxygen sensor signal fault (Front pre-catalyst) : Ageing
P2098 Downstrean oxygen sensor signal fault (Rear pre-catalyst) : Ageing
P2099 Downstrean oxygen sensor signal fault (Rear pre-catalyst) : Ageing
P2101 Motorised throttle stops programming fault
P2137 Accelerator pedal sensor tracks 1 and 2 signal fault : Coherence
P2176 Motorised throttle stops programming fault : Idle position not programmed
P2177 Fault: richness regulation at limit (Front row of cylinders) : Mixture too
weak at idle
P2178 Fault: richness regulation at limit (Front row of cylinders) : Mixture too
rich at idle
P2179 Fault: richness regulation at limit (Rear row of cylinders) : Mixture too
weak at idle
P2180 Fault: richness regulation at limit (Rear row of cylinders) : Mixture too
rich at idle
P2191 Fault: richness regulation at limit (Front row of cylinders) : Mixture too
weak under load
P2192 Fault: richness regulation at limit (Front row of cylinders) : Mixture too
rich under load
P2193 Fault: richness regulation at limit (Rear row of cylinders) : Mixture too
weak under load
P2194 Fault: richness regulation at limit (Rear row of cylinders) : Mixture too
rich under load
P2299 Accelerator pedal detected stuck fault : Lack of coherence between the brake
switch information and the accelerator pedal information
P3010 Throttle position regulation fault : Difference between the motor control and
the position of the system
P3011 Throttle position regulation fault : Return spring ineffective
P3012 Throttle position regulation fault : Opening spring ineffective
P3013 Motorised throttle stops programming fault : Programming not carried out
P3014 Motorised throttle stops programming fault : Initialisation conditions not
met
P3015 Butterfly position sensor signal fault : Signal amplified
U0028 MIL lamp diagnostics reception on the CAN fault : Absence of frames
U0055 Fault: absence of communication on the comfort CAN : Absence of frames
U0103 Communication with the automatic gearbox ECU missing : Absence of frames
U0122 Fault: absence of communication with the ESP ECU : Absence of frames
U0404 Fault in communication between the automatic gearbox ECU and the engine
management ECU : Absence of frames
U1000 Fault in communication between the engine management ECU and the other ECUs
on the (CAN)
U1003 No communication on the CAN fault : Absence of frames
U1107 Fault: absence of communication with the GEP ECU : Absence of frames
U1118 Communication with the Built-in Systems Interface ECU missing : Absence of
frames
U2000 Remote controlled triggering information fault : Absence of frames
U2003 Remote controlled triggering information fault : Value received incorrect
U2108 Remote controlled triggering information fault : Coherence
U2118 Remote controlled triggering information fault : Value received incorrect
RD4 RDS COMPACT DISC AUDIO SYSTEM OR RD4/MP3 RDS COMPACT DISC AUDIO SYSTEM
RD4/MP3 RDS COMPACT DISC AUDIO SYSTEM OR RD4 RDS COMPACT DISC AUDIO SYSTEM
F003 Fault absence of communication with the built-in systems interface : Not
defined
F00A CAN network fault : Not defined
F00F ECU not communicating on the CAN fault : Not defined
F024 Fault absence of communication with the engine fuse box : Not defined
F300 Fault: calibration downloading (blank ECU) : Not defined
FEC4 Rain detector fault : Not defined
FEC5 Infrared light detector lighting fault : Not defined
FEC6 Tunnel detector fault : Not defined
FEC7 Ambient light detector fault : Not defined
FECC Fault adaptation of the windscreen sensor impossible : Not defined
FECE Built-in systems interface data not valid fault : Not defined
FECF Engine fuse box data not valid fault : Not defined
F003 Fault absence of communication with the built-in systems interface : Not
defined
F00A CAN network fault : Not defined
F00F ECU not communicating on the CAN fault : Not defined
F1A4 Switches information fault : Not defined
F780 Jamming fault on seat up switch : Not defined
F781 Jamming fault on seat down switch : Not defined
F782 Jamming fault on slide forward switch : Not defined
F783 Jamming fault on slide rearward switch : Not defined
F784 Jamming fault on height up switch : Not defined
F785 Jamming fault on height down switch : Not defined
F788 Jamming fault on backrest recline switch : Not defined
F789 Jamming fault on backrest upright switch : Not defined
F793 Jamming fault on memorisation keypad button 1 : Not defined
F794 Jamming fault on memorisation keypad button 2 : Not defined
F795 Jamming fault on memorisation keypad button 3 : Not defined
F796 Jamming fault on memorisation keypad button M : Not defined
F797 Lumbar supports raising switch jamming fault : Not defined
F798 Lumbar supports lowering switch jamming fault : Not defined
F799 Jamming fault on lumbar support forward switch : Not defined
F79A Jamming fault on lumbar support rearward switch : Not defined
8C98 ECU fault : Error checking/writing the high frequency identifier in the memory
(during programming of the keys) : No signal
9C85 Lighting stalk fault : Coherence
9C86 Lighting control stalk button fault : Coherence
9C87 Wiper control stalk button fault : Coherence
9C88 Windscreen wipers switch fault : Coherence
9C92 Cruise control and speed limiter switch fault : Coherence
AC83 Transponder aerial fault : Short circuit to positive
BC80 ECU fault (High frequency receiver) : Short circuit to earth
BC85 Lighting controls fault : Short circuit to earth
BC88 Windscreen wipers control fault : Short circuit to earth
BC92 Cruise control/speed limiter control fault : Short circuit to earth
BFE0 Steering wheel button module fault : Short circuit to earth
CC85 Lighting controls fault : Open circuit
CC88 Windscreen wipers control fault : Open circuit
CFE0 Steering wheel button module fault : Open circuit
DC9E ECU supply voltage fault : Low stop
EC9E ECU supply voltage fault : High stop
F003 Fault absence of communication with the built-in systems interface
F00A CAN network fault : Coherence
F00F ECU not communicating on the CAN fault
FC80 High frequency reception fault
FC81 Key transponder fault
FC82 Fault in communication with the transponder
FC83 Fault in communication with the transponder
FC84 Transponder label reading fault
FC85 Lighting controls fault
FC86 Fault in the button at the end of the lighting control stalk
FC87 Fault in the button at the end of the wiper control stalk
FC88 Windscreen wipers control fault
FC89 Radio controls fault
FC8C F1 steering wheel button fault
FC8D F2 steering wheel button fault
FC8E FF3 steering wheel button fault
FC8F FF4 steering wheel button fault
FC92 Cruise control/speed limiter control fault
FC93 Horn control fault
FC94 Radio satellite control fault
FC95 F5 steering wheel button fault
FC96 F6 steering wheel button fault
FC98 Internal fault in the ECU
FC99 Internal fault in the ECU
FC9D Fault failure of the internal ECU test
FC9F Horn button fault
U1208 Communication with the engine management ECU : Value received incorrect
U1213 Communication with the ESP ECU : Value received incorrect
U1218 Communication with the BSI : Value received incorrect
U2000 Main wake-up
U2003 Main wake-up
U2005 Triggering (vehicle speed receipt anomaly)
U2006 Triggering (engine speed receipt anomaly)
U2118 Triggering (height adjustment receipt anomaly)
F003 Fault: absence of communication between the BSI and the rear air conditioning
ECU
F00A CAN network fault
F00F ECU not communicating on the CAN fault
F70E Fault with the rear evaporator temperature sensor : Not defined
F70F Rear or rear left air conditioning panel control button fault : Not defined
F710 Rear right air conditioning control panel control button fault : Not defined
F735 Rear or rear left mixing motor fault : Not defined
F736 Rear right mixing motor fault : Not defined
F737 Rear or rear left distribution motor fault : Not defined
F738 D?faut du moteur de distribution arri?re droit : Not defined
F739 Rear blower motor fault
F739 D?faut du pulseur d?air arri?re gauche : Not defined
F73D Rear mixing motor fault
F73E Cold loop electrovalve fault
F73F Hot loop electrovalve fault
F740 Hot loop fault (coolant pump)
F761 Internal fault in the ECU
F766 Fault: absence of communication with the stepper motors (LIN)