Escolar Documentos
Profissional Documentos
Cultura Documentos
NA to SLS EN 1992-1-1:2013
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05 2017-08-05
SRI LANKA STANDARDS INSTITUTION
Single-user licence only, copying and networking prohibited. Single-user licence only, copying and networking prohibited.
SRI LANKA NATIONAL ANNEX TO
EUROCODE 2: DESIGN OF CONCRETE STRUCTURES —
PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
NA to SLS EN 1992-1-1:2013
Gr. 8
© SLSI 2013
All right reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any
form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in
writing from the SLSI.
Copyright Reserved
SRI LANKA STANDARDS INSTITUTION
17, Victoria Place
Elvitigala Mawatha
Colombo 8
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya Licensed by SLSI to Department Civil Engineering - University of Peradeniya
Sri ofLanka
2017-08-05 2017-08-05
Single-user licence only, copying and networking prohibited. Single-user licence only, copying and networking prohibited.
Committees responsible for this National Annex
The preparation of this National Annex was entrusted by Committee SC35/WG/12, upon which the following
bodies were represented:
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05 2017-08-05
Single-user licence only, copying and networking prohibited. Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
3.3.6 (7)
3.3.4 (5)
3.2.7 (2)
3.1.2 (4)
2.3.3 (3)
PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
2.4.2.3 (1)
2.4.2.5 (2)
2.4.2.4 (2)
2.4.2.4 (1)
2.4.2.2 (3)
2.4.2.2 (2)
2.4.2.2 (1)
2.4.2.1 (1)
3.2.2 (3) P
3.1.6 (2) P
3.1.6 (1) P
3.1.2 (2) P
Sub clause
INTRODUCTION
This National Annex has been prepared by the Working group on the development of the National Annexes to
Value of k
Value of kt
Value of kf
Value of ct
Euro Codes (SC35/WG/12), structural use of concrete. It is to be used in conjunction with SLS EN 1992-1-
Value of cc
local effects
NA to SLS EN 1992-1-1:2013
Value of djoint
Value of Cmax
1:2012.
tendons: value of ud
2017-08-05
was authorized for adoption and publication as a Sri Lanka National Annex by the Council of the Sri Lanka
ud
ultimate limit states C and S
Partial factors for materials for
Partial factors for materials for
Partial factor for prestress P, fav
Partial factor for prestress P, unfav
NA.1 SCOPE
1.0
1.0
1.0
1.1
1.1
1.0
1.2
1.3
1.0
1.0
following sub clauses of SLS EN 1992-1-1:2012:
0.85
30 m
0.9 uk
C90/105
ud =0.02
— 2.3.3 (3) — 4.4.1.3 (4) — 6.4.3 (6) — 9.2.1.3 (1) — 11.3.5 (1)P
600 MPa
Table 2.1N
— 2.4.2.1 (1) — 5.1.3 (1)P — 6.4.4 (1) — 9.2.1.4 (1) — 11.3.5 (2)P
fpO.lk/fpk = 0.9
— 2.4.2.2 (1) — 5.2 (5) — 6.4.5 (3) — 9.2.2 (4) — 11.3.7 (1)
— 2.4.2.2 (2) — 5.5 (4) — 6.4.5 (4) — 9.2.2 (5) — 11.6.1 (1)
— 2.4.2.2 (3) — 5.6.3 (4) — 6.5.2 (2) — 9.2.2 (6) — 11.6.1 (2)
4
— 2.4.2.4 (1) — 5.8.3.3 (1) — 6.5.4 (6) — 9.2.2 (8) — 11.6.4.1 (1)
Eurocode recommendation
— 2.4.2.4 (2) — 5.8.3.3 (2) — 6.8.4 (1) — 9.3.1.1 (3) — 12.3.1 (1)
— 2.4.2.5 (2) — 5.8.5 (1) — 6.8.4 (5) — 9.5.2 (1) — 12.6.3 (2)
— 3.1.2 (2)P — 5.8.6 (3) — 6.8.6 (1) — 9.5.2 (2) — A.2.1 (1)
50 m
— 3.1.2 (4) — 5.10.1 (6) — 6.8.6 (3) — 9.5.2 (3) — A.2.1 (2)
500 MPa
— 3.1.6 (2)P — 5.10.2.1 (2) — 7.2 (2) — 9.6.2 (1) — A.2.2 (2)
— 3.2.2 (3)P — 5.10.2.2 (4) — 7.2 (3) — 9.6.3 (1) — A.2.3 (1)
— 3.2.7 (2) — 5.10.2.2 (5) — 7.2 (5) — 9.7 (1) — C.1 (1)
TABLE NA.1 – Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012
— 4.4.1.2 (7) — 6.2.2 (6) — 8.3 (2) — 9.8.5 (3) — J.3 (2)
— 4.4.1.2 (8) — 6.2.3 (2) — 8.6 (2) — 9.10.2.2 (2) — J.3 (3)
TABLE NA.1 – Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012(continued)
5
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 – Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012 (continued)
6
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 – Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012 (continued)
7
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 – Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012(continued)
8
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 – Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012 (continued)
Sub clause Nationally Determined Parameter Eurocode recommendation Sri Lanka Decision
6.2.3 (3) Values of v1 and cw v1= v as described by Use the recommended values
Expression (6.3N) or takes the values given in
Expressions (6.10.aN) and (6.10.bN)
cw takes the values given in Expressions
(6.11 aN), (6.11.bN) and (6.11 cN)
6.2.4 (4) Range of values of cot f 1.0 ≤ cot f ≤ 2.0 for compression flanges Use the recommended value
1.0 ≤ cot f ≤ 1.25 for tension flanges
6.2.4 (6) Value of k 0.4 Use the recommended value
6.4.3 (6) Values of = 1.5 for a corner column Use the recommended values
= 1.4 for an edge column
= 1.15 for an internal column
6.4.4 (1) Values of CRd,c, vmin and k 1 for punching shear CRd,c = 0.18/ c Use the recommended values
vmin = 0.035 k 3/2fck1/2 (refer also to 3.1.2 (2)P for a
k 1 = 0.1 requirement for concrete class
> C50/60)
6.4.5 (3) The value of maximum punching resistance VRd,max = 0.5vfcd Use the recommended value
adjacent to column VRd,max
6.4.5 (4) The distance kd of the outer perimeter of punching k = 1.5 k = 1.5 unless the perimeter at
shear reinforcement from the perimeter Uout which the reinforcement is no
longer required is less than 3d
from the face of the loaded
area/column. In this case the
reinforcement should be placed
in the zone 0.3d and 1.5d from
the face of the column.
6.5.2 (2) Value of v’ v’ = 1 - fck/250 Use the recommended value
6.5.4 (4) Value of k1, k2, k3 k1 = 1.0 Use the recommended values
k2 = 0.85
k3 = 0.75
6.5.4 (6) Value of k 4 k 4 = 3.0 Use the recommended value
9
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 – Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012 (continued)
Sub clause Nationally Determined Parameter Eurocode recommendation Sri Lanka Decision
6.8.4 (1) Values of F,fat and parameters for S-N curves F,fat = 1.0 Use the recommended values
10
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 – Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012(continued)
Sub clause Nationally Determined Parameter Eurocode recommendation Sri Lanka Decision
8.6 (2) Anchorage capacity of a welded bar Fbtd = ltdøt td ≤ Fwd Use the recommended value
8.8 (1) Additional rules for large ølarge > 32 mm Use the recommended value
diameter bars: limiting bar size
9.2.1.1 (1) Beams: minimum reinforcement areas As,min = 0.26(fctm/fyk)btd ≥ 0.001 3btd Use the recommended value
9.2.1.1 (3) Beams: maximum reinforcement areas As,max = 0.04Ac Use the recommended value
9.2.1.3 (1) Beams: minimum ratio of span bending moment to be 1 = 0.15 1 = 0.3
assumed at supports in monolithic construction
9.2.1.4 (1) Anchorage of bottom reinforcement at an end support: area 2 = 0.25 1 = 0.3
of steel provided over supports with little or no
end fixity in design
9.2.2 (4) Minimum ratio of shear reinforcement in the form of links 3 = 0.5 Use the recommended value
9.2.2 (5) Minimum shear reinforcement w,min = (0.08√fck)/ fyk Use the recommended value
9.2.2 (6) Maximum longitudinal spacing of shear assemblies sl,max = 0.75d(1 + cot ) Use the recommended value
9.2.2 (7) Maximum longitudinal spacing of bent-up bars sb,max = 0.6d (1 + cot ) Use the recommended value
11
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 — Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012 (continued)
12
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 — Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012 (continued)
13
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 — Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012 (continued)
14
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 — Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012 (continued)
A.2.3 (1) Values of and c,red4 =0.85 Use the recommended values
c,red4 = 1.3
C.1 (1) Value for fatigue stress range, minimum Table C.2N Use the recommended values
relative rib area and = 0.6
C.1 (3) Note 1 Values of a for determination of fyk, k, uk For fyk, a = 10 MPa; k, a = 0, uk, a=0 Use the recommended values
C.1 (3) Note 2 Values of a for determination of fyk, k, uk Minimum and maximum values for fyk, Use the recommended values
k, uk in accordance with Table C.3N
15
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.1 — Sri Lanka decisions for Nationally Determined Parameters described in SLS EN 1992-1-1:2012 (continued)
J.2.2 (2) Values of tan 0.4 ≤ tan ≤ 1 Use the recommended value
J.3 (2) Value of k1 0.25 Use the recommended value
J.3 (3) Value of k2 0.5 Use the recommended value
16
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
NA to SLS EN 1992-1-1:2013
TABLE NA.3 – Basic ratios of span/effective depth for reinforced concrete members without axial compression
Cantilever 0.4 6 8
NOTE :
1. The values given have been chosen to be generally conservative and calculation may frequently show that thinner
members are possible.
2. For two-way spanning slabs, the check should be carried out on the basis of the shorter span. For flat slabs the longer
span should be taken.
3. The limits given for flat slabs correspond to a less severe limitation than a mid-span deflection of span/250 relative to
the columns. Experience has shown this to be satisfactory.
4. The values of k in the table may not be appropriate when the formwork is struck at an early age or when the construction
loads exceed the design load. In these cases, the deflections may have to be calculated using advice in specialist literature,
e.g the Concrete Society’s report on deflections in concrete slabs and beams [1] and an article for the Magazine of
Concrete Research entitled “ Are existing span to depth rules conservative for flat slabs?” [2]
5. The ratio of area of reinforcement provided to that required should be limited to 1.5 when the span/depth ratio is
adjusted. This limit also applies to any adjustments to span/depth ratio obtained from Expressions (7.16a) or (7.16b) from
which this table has been derived for concrete class C30/37.
1 — Deflections in concrete slabs and beams, Technical Report No.58, Concrete Society 2005.
2 —VOLLUM, R.L. and T.R. HOSSAIN, Are existing span t depth rules conservative for flat slabs?, Magazine of Concrete Research, vol. 54, issue 6,
2002.
……………………………../……………………………….
17
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05
Single-user licence only, copying and networking prohibited.
Licensed by SLSI to Department of Civil Engineering - University of Peradeniya Licensed by SLSI to Department of Civil Engineering - University of Peradeniya
2017-08-05 2017-08-05
Single-user licence only, copying and networking prohibited. Single-user licence only, copying and networking prohibited.