Escolar Documentos
Profissional Documentos
Cultura Documentos
Sepam series 80
Configuration
Customer: .......................................................................... a
Project: .............................................................................. a
Switchboard: ..................................................................... a
Cubicle: ............................................................................. a
Contents
Sepam label: .................................................................................................................. sepam F3 (R5) Application type: M81 Model: In tegrated UMI
MES120 (14 input + 6 output module) n°1 ................................................................. Present
MES120 (14 input + 6 output module) n°2 ................................................................. Absent
MES120 (14 input + 6 output module) n°3 ................................................................. Absent
MSA141 (1 analog output module) .............................................................................. Present Type of output 4 - 20mA Variable: Current phase 2 (x 0.1 A)
Min. value: -100 Max. value: 100
MET148 (8 temperature sensors module) n°1 ........................................................... Present Type of t emp. sensor PT100 Assignment of temperature sensors Other Use
MET148 (8 temperature sensors module) n°2 ........................................................... Absent
COM1 module ................................................................................................................ Absent
COM2 module ................................................................................................................ Absent
ACE 850 (communication network interface) (Ethernet) .......................................... Present Communication protocol Eth ernet-FO IP address 172.20.12.15
Motor/Generator speed
Rated speed (Rpm) 3000 rpm Zero speed threshold 5 %
Pulses per rotation 1
Description Setting
Switchgear control No
Logic discrimination No
Load shedding No
Time delay 0 ms
Restart No
Time delay 0 ms
Max. dip duration 300 s
1 2
I/Is 1.00 10.00
T(s) 1.00 1.00
Measurement Settings
Unit Activity Latching Confirmation Group
origin Tripping curve Threshold Delay Timer hold curve Timer hold
Sta ndard
No A 1 kA 1s Definite time 0 ms
1 On X I1,I2,I3 inver se time
confirmation
B Definite time 1.26 kA 100 ms Definite time 0 ms
No A Definite time 2.80 kA 100 ms Definite time 0 ms
2 On X I1,I2,I3
confirmation B Definite time 1.26 kA 100 ms Definite time 0 ms
No A Definite time 1.26 kA 100 ms Definite time 0 ms
3 Off X I1,I2,I3
confirmation B Definite time 1.26 kA 100 ms Definite time 0 ms
No A Definite time 1.26 kA 100 ms Definite time 0 ms
4 Off X I1,I2,I3
confirmation B Definite time 1.26 kA 100 ms Definite time 0 ms
No A Definite time 1.26 kA 100 ms Definite time 0 ms
5 Off X I1,I2,I3
confirmation B Definite time 1.26 kA 100 ms Definite time 0 ms
No A Definite time 1.26 kA 100 ms Definite time 0 ms
6 Off X I1,I2,I3
confirmation B Definite time 1.26 kA 100 ms Definite time 0 ms
No A Definite time 1.26 kA 100 ms Definite time 0 ms
7 Off X I1,I2,I3
confirmation B Definite time 1.26 kA 100 ms Definite time 0 ms
No A Definite time 1.26 kA 100 ms Definite time 0 ms
8 Off X I1,I2,I3
confirmation B Definite time 1.26 kA 100 ms Definite time 0 ms
Measurement Settings
Unit Activity Latching Group
origin Tripping curve Threshold Delay Timer hold curve Timer hold H2 rest.
Sta ndard
A 200 A 1s Definite time 0 ms
1 On X Io sum inver se time
B Definite time 630 A 100 ms Definite time 0 ms
A Definite time 800 A 100 ms Definite time 0 ms
2 On X Io sum
B Definite time 630 A 100 ms Definite time 0 ms
A Definite time 630 A 100 ms Definite time 0 ms
3 Off X Io sum
B Definite time 630 A 100 ms Definite time 0 ms
A Definite time 630 A 100 ms Definite time 0 ms
4 Off X Io sum
B Definite time 630 A 100 ms Definite time 0 ms
A Definite time 630 A 100 ms Definite time 0 ms
5 Off X Io sum
B Definite time 630 A 100 ms Definite time 0 ms
A Definite time 630 A 100 ms Definite time 0 ms
6 Off X Io sum
B Definite time 630 A 100 ms Definite time 0 ms
A Definite time 630 A 100 ms Definite time 0 ms
7 Off X Io sum
B Definite time 630 A 100 ms Definite time 0 ms
A Definite time 630 A 100 ms Definite time 0 ms
8 Off X Io sum
B Definite time 630 A 100 ms Definite time 0 ms
Settings
Unit Activity Latching Use closed
Is threshold Delay position of CB
1 Off X 200 A 200 ms
Settings
Unit Activity Latching
Tripping curve Threshold Delay
1 On X Definite time 10 %Ib 100 ms
2 Off X Definite time 10 %Ib 100 ms
Measurement
Unit Activity Latching
origin
1 On X I1,I2,I3
Settings
Measurement
Unit Activity Latching Type Group Curve Delay
origin Tripping curve Is o threshold Delay Angle Voltage Threshold Direction hold hold
Definite
A Definite time 1.26 kA 100 ms 0° 2 %Unp Line 0 ms
time
1 Off X Io sum Type2
Definite
B Definite time 1.26 kA 100 ms 0° 2 %Unp Line 0 ms
time
Definite
A Definite time 1.26 kA 100 ms 0° 2 %Unp Line 0 ms
time
2 Off X Io sum Type2
Definite
B Definite time 1.26 kA 100 ms 0° 2 %Unp Line 0 ms
time
Settings
Unit Activity Latching
Type Power threshold Delay
Reverse
1 Off X 1 MW 100 ms
power
Reverse
2 Off X 1 MW 100 ms
power
Settings
Unit Activity Latching
Type Power threshold Delay
Reverse
1 Off X 6.55 MVAR 100 ms
power
Settings
Unit Activity Latching
Threshold Delay
1 Off 20 %Ib 100 ms
Settings
Unit Activity Latching Delay f or exces. Delay f or locked Delay f or locked
Threshold starting time (ST) rotor (LT) rotor on start (LTS)
1 Off X 50 %Ib 100 s 100 s 100 s
Settings
Unit Activity Latching period Total number Number of consec. Number of consec. Delay
Time of starts hot starts cold starts bet. stop/start
1 Off 1 hr 1 1 1 0 min
Settings
Unit Activity Latching
Xa (Common point of the 2 circles) Xb (Circle1 definition point) Xc (Circle2 definition point) Circle1 time delay Circle2 time delay
1 Off X 2.5 Ohm 20.8 Ohm 42.800 Ohm 70 ms 500 ms
Settings
Unit Activity Latching
Protection principle(s) Delay
1 Off X Equal-area criterion 700 ms
Settings
Unit Activity Latch
Speed threshold Time delay T
1 Off 110 %rated speed 1s
2 Off 110 %rated speed 1s
Settings
Unit Activity Latch
Speed threshold Time delay T
1 Off 20 %rated speed 1s
2 Off 20 %rated speed 1s
Measurement Settings
Unit Activity Latching
origin Voltage threshold Delay
V1,V2,V3 /
1 Off X 30 %Unp 100 ms
U21,U32
V1,V2,V3 /
2 Off X 30 %Unp 100 ms
U21,U32
Measurement Settings
Unit Activity Latching
origin Voltage threshold Delay
V1,V2,V3 /
1 Off 20 %Unp 100 ms
U21,U32
V1,V2,V3 /
2 Off 20 %Unp 100 ms
U21,U32
Measurement Settings
Unit Activity Latching
origin Tripping curve mode Voltage threshold Delay
V1,V2,V3 /
1 On Definite time Phase-to -phase 10 %Unp 100 ms
U21,U32
V1,V2,V3 /
2 Off Definite time Phase-to -phase 10 %Unp 100 ms
U21,U32
V1,V2,V3 /
3 Off Definite time Phase-to -phase 10 %Unp 100 ms
U21,U32
V1,V2,V3 /
4 Off Definite time Phase-to -phase 10 %Unp 100 ms
U21,U32
Measurement Settings
Unit Activity Latching
origin Mode Voltage threshold Delay
V1,V2,V3 /
1 Off Phase-to -phase 110 %Unp 100 ms
U21,U32
V1,V2,V3 /
2 Off Phase-to -phase 110 %Unp 100 ms
U21,U32
V1,V2,V3 /
3 Off Phase-to -phase 110 %Unp 100 ms
U21,U32
V1,V2,V3 /
4 Off Phase-to -phase 110 %Unp 100 ms
U21,U32
Measurement Settings
Unit Activity Latching
origin Tripping curve Voltage threshold Delay
1 Off Vo Definite time 10 %Unp 100 ms
2 Off Vo Definite time 10 %Unp 100 ms
Measurement Settings
Unit Activity Latching
origin Voltage threshold Delay
V1,V2,V3 /
1 Off 10 %Unp 100 ms
U21,U32
V1,V2,V3 /
2 Off 10 %Unp 100 ms
U21,U32
Measurement Settings
Unit Activity Latch
origin Fs threshold Delay Vs threshold
1 Off V1,V2,V3/U21,U32 53 Hz 100 ms 20 %Un
2 Off V1,V2,V3/U21,U32 53 Hz 100 ms 20 %Un
Settings
Measurement
Unit Activity Latch df/dt
origin Fs threshold Delay Vs threshold restraint
1 Off V1,V2,V3/U21,U32 45 Hz 100 ms 20 %Un No
2 Off V1,V2,V3/U21,U32 45 Hz 100 ms 20 %Un No
3 Off V1,V2,V3/U21,U32 45 Hz 100 ms 20 %Un No
4 Off V1,V2,V3/U21,U32 45 Hz 100 ms 20 %Un No
Settings Settings
Unit Activity Latch Unit Activity Latch
Alarm Trip Alarm Trip
1 On X 180 °C 180 °C 9 Off X 180 °C 180 °C
2 On X 180 °C 180 °C 10 Off X 180 °C 180 °C
3 On X 180 °C 180 °C 11 Off X 180 °C 180 °C
4 On X 180 °C 180 °C 12 Off X 180 °C 180 °C
5 On X 180 °C 180 °C 13 Off X 180 °C 180 °C
6 On X 180 °C 180 °C 14 Off X 180 °C 180 °C
7 On X 180 °C 180 °C 15 Off X 180 °C 180 °C
8 On X 180 °C 180 °C 16 Off X 180 °C 180 °C
3.1. Logipam
Author: ......................
Customer: ................
Project: .....................
Switchboard: ...........
Cubicle: ....................
Led1 Led2 Led3 Led4 Led5 Led6 Led7 Led8 Led9 English message Local message Rec.
50/51 - 1 X X X
50/51 - 2 X X X
50/51 - 3 X
50/51 - 4 X
50/51 - 5 X
50/51 - 6 X
50/51 - 7 X
50/51 - 8 X
50N/51N - 1 X X X
50N/51N - 2 X X X
50N/51N - 3 X
50N/51N - 4 X
50N/51N - 5 X
50N/51N - 6 X
50N/51N - 7 X
50N/51N - 8 X
50BF - 1 X
46 - 1 X X
46 - 2 X
49RMS - 1 X
49RMS - inhibit
49RMS - alarm
67N - 1 X
67N - 2 X
32P - 1 X
Led1 Led2 Led3 Led4 Led5 Led6 Led7 Led8 Led9 English message Local message Rec.
Pic k-up X
Drop-out
TCS fault
Breaker monitoring
Reverse phase rotation
Disturbance recording inhibited
MET148 No 1 RTD fault
Low battery fault
Cumulative breaking current monitoring
Watchdog
Led1 Led2 Led3 Led4 Led5 Led6 Led7 Led8 Led9 English message Local message Rec.
I101 (Breaker closed) X
I102 (Breaker open) X
I103 (Other use)
I104 (Other use)
I105 (Other use)
I106 (Other use)
I107 (Other use)
I108 (Other use)
I109 (Other use)
I110 (Other use)
I111 (Other use)
I112 (Other use)
I113 (Other use)
I114 (Other use)
Led1 Led2 Led3 Led4 Led5 Led6 Led7 Led8 Led9 English message Local message Rec.
V1
V2
V3
V4
V5
V6
V7
V8
V9
V10
V11
V12
V13
V14
V15
V16
V17
V18
V19
V20
Led1 Led2 Led3 Led4 Led5 Led6 Led7 Led8 Led9 English message Local message Rec.
G401 (------- (Not used) -----------)
G402 (------- (Not used) -----------)
G403 (------- (Not used) -----------)
G404 (------- (Not used) -----------)
G405 (------- (Not used) -----------)
G406 (------- (Not used) -----------)
G407 (------- (Not used) -----------)
G408 (------- (Not used) -----------)
Description Setting
Activity On
Total recording time: 21 s
Memory used: 93 %
Number of recordings: 6
Duration of a recording: 3
Number of samples stored per period: 12
Number of Pretrig. periods: 36