Escolar Documentos
Profissional Documentos
Cultura Documentos
To,
Site: Star Ayodhya Textile Market (A.T.M).
F.P.No: 41+42,
T.P.S No: 19(Parvat-Magob),
Ta: City, Dist: Surat
Dear Sirs,
With reference to the above referred site investigation, herewith, we are submitting detailed Sub
Soil Investigation Report based, physical and engineering testing of soil characteristics.
This report is based on four boreholes data up to 40.45m depth from ground level. Borehole
locations were selected with engineer in-charge. If any change in strata other than the location
of the borehole mentioned in this report is observed at the time of excavation, it is advisable to
contact us immediately for further investigation.
Thanking you.
Sincerely Yours,
Authorized Signatory
REPORT
ON
SUB-SOIL
INVESTIGATION
Prepared By
Bhumi Research Center
(Government Approved Laboratory)
2/1362, “Bhumi House”,
Sagrampura, Opp: Sub Jail,
Ring Road, Surat-395002.
Phone: 2363600, 2363700.
CONTENTS
SR. NO. TITLE SHEET NO.
01 INTRODUCTION 01
02 SITE INFORMATION 02
03 FIELD WORK 02
04 SUB SOIL STRATIFICATION 04
05 ANALYSIS OF DATA 05
06 BEARING CAPACITY OF SOIL 08
07 SUMMARY 09
08 CONCLUSION AND RECOMMENDATIONS 15
09 TABLES
9.1) FIELD PROGRAM SUMMARY 18
9.2) SUMMARY OF GRAIN SIZE ANALYSIS 22
9.3) SHEAR & CONSOLIDATION PARAMETERS 26
1P0 FIGUREPS
10.1) LOCATION MAP 27
10.2) LOG OF SPT ‘N’ & ATTERBERG LIMITS 28
10.3) PARTICLE SIZE DISTRIBUTION CURVES 32
10.4) CONSOLIDATION CURVE 40
11 BORE LOG OF EXPLORATION 43
12 IS CLASSIFICATION OF SOIL 47
13 REFERENCES/BIBLIOGRAPHY 48
REPORT ON SUB SOIL EXPLORATION
1.0 INTRODUCTION:
The investigation of the site is an essential prerequisite to the construction of all civil
engineering works with a view to assess the general suitability of the site for the proposed
new works and to enable in preparing an adequate and economic design.
In particular, it is necessary to assess the changes that may occur during or after the
construction of structure due to the choice of materials or methods of construction, which
may adversely affect safety of structure or after its performance or utility.
It is usually judicious to collect information relating to the site prior to commencing its
exploration. The exploration of the site for an important structure requires the exploration
and sampling of all strata likely to be significantly affected by the structural load. The
extent of this exploration will depend on the site and structure.
All structures rest on the foundation soil and their performance depends on soil behavior.
Soil forms the most widely used material of construction of earth dams, roads and canals.
To study the behavior of soil in foundation or earthwork engineering, properties of soil
under the actual field conditions have to be obtained.
Soil mechanics is the application of the laws of mechanics and hydraulics to engineering
problems dealing with sediments and other unconsolidated accumulation of solid particles
produced by the mechanical and chemical disintegration of rocks, regardless of whether or
not they contain an admixture of organic constituent.
Soil mechanics provides guidance in design of foundations, rigid & flexible pavements,
underground and earth retaining structures, embankments and excavations and earth dams.
Soil engineering embodies the use of best practices in exploration, testing, design &
construction controls.
Soil exploration provides the detailed sub soil conditions such as Stratification, Hardness &
Denseness of the strata, Water table level, Compressibility, Soil stability, Stress analysis,
Shearing resistance & Failure analysis.
The controlled strain method was used in case of shear test. These parameters are
used in evaluation of stability analysis and in evaluation of ultimate bearing capacity.
The cylindrical specimen for triaxial compression (without the measurement of pore
water pressure) was prepared from undisturbed sample. Shear as well as Triaxial
Compression Test (Unconsolidated Undrained) was conducted.
Direct Shear Test was conducted on specimen remolded at FDD and submerged for
24 hrs saturation.
Triaxial Compression (Unconsolidated Undrained Condition) test was conducted
without the measurement of pore water pressure on undisturbed mould specimen.
These results for individual samples are summarized under Table No. 9.3.
5.2.5 Swelling Characteristics:
Soil sample at and below the foundation depth from GL was tested for swelling
characteristics.
The Shrinkage limit ranges from 22 to 30% for BH – 01 to 04.
The Volumetric Differential Swelling Index ranges from N.O. to 130% for BH – 01
to 04.
These characteristics show low expansive nature of stratum at the foundation depth
from GL.
5.2.6 Consolidation Characteristics:
The main purpose of consolidation tests is to obtain soil data, which are used in
predicting the rate and the amount of settlement of the structure. Compression index
Cc indicates the magnitude of compression and the over consolidation pressure Pc
indicates the compaction of strata at natural condition. This test gives the values of
various parameters as under @ the foundation depth. This test is performed at
10.00m depth in BH-01, 12.00m depth in BH-02 and 10.50m depth in BH-03 from
EGL.
Interpolation Values
dq=dy
sc sq sy dc (f>10) W' FOS
1.18 1.18 0.65 2.00 1.50 0.50 3.20
The Ultimate Bearing capacity qn u = c Nc' sc dc ic + q (Nq'-1) sq dq iq + 0.5 B γ' Ny' sy dy iy W'
2
The Ultimate net bearing capacity qn u= 130.80 (t/m )
2
With FOS, The net SBC qn u (s)= 40.87 (t/m )
Depth of foundation:Df (m) 11.50 Water Table Correction Factor W" 0.5
Length of foundation: L (m) 4.00 Depth Factor Rd 1.2
Width of foundation: B (m) 3.50 Rigidity Factor Rr 0.8
G.W.T. from EGL (m) 0.00 Permission Settelment (s) mm 100
Expected Bearing capacity (qu) t/m2 . 40.87 Average Corrected SPT N Value N' 47
Specific Gravity 2.51
FDD (γ) gm/cc 1.58
Void Ratio (e) 0.58
Safe Bearing Pressure Pc = 55.4(N'-3)/40((B+0.3)/2B)2*Rr*Rd*s
40.00 SM
For the Clayey strata, no overburden correction has applied & the dilatancy correction is applied for the stratum consists of fine sand and silt
below water table as per IS:2131-1981,RA2002.
For the SPT test termination, the SPT N values are extrapolated for 300mm based on the penetration for 50 blows.
36.00 >50 04cm 375 1.96 0.00 MI 70.54 0.35 375 195
37.50 >50 06cm 250 1.96 0.00 ML 73.48 0.34 250 133
Authorized Signatory
18 56
25 IP
1.50 to 1.95 CH 63 13 25 UDS
13 63
IP
3.00 to 3.45 CI 43 19 S 5 6 8 14 14
19 43
IP
4.50 to 4.95 CI 39 22 22 UDS 22
22 39
IP
6.00 to 6.45 CI 40 17 S 11 26 26 52 52
17 40
IP
9.00 to 9.45 CH 52 26 S 13 35 36 71 71
26 52
IP
10.00 to 10.45 CI 44 24 22 UDS 22
24 44
IP
11.00 to 11.45 CH 92 22 S 25 43 47 90 90
22 92
16.50 to 16.95 SM 36 NP S 56 80 - 80 80 NP
36
18.00 to 18.45 GM 36 NP S 10 45 50 95 95 NP
36
NMC
LL
PL
19.50 to 19.95 GM 36 NP S 17 33 48 81 81 NP
36
25.50 to 25.95 GM 35 NP S NP
35
27.00 to 27.45 GM 33 NP S 22 30 50 80 80 NP
33
23 45
IP
6
1.50 to 1.95 CI 41 15 S 2 2 4 6
15 41
IP
3.00 to 3.45 CI 45 26 25 UDS 25
26 45
IP
4.50 to 4.95 CI 45 24 S 3 4 6 10 10
24 45
IP
6.00 to 6.45 CL 31 20 15 UDS 15
20 31
IP
7.50 to 7.95 CH 60 23 S 14 19 28 47 47
23 60
18
21 49
IP
10.50 to 10.95 CI 47 27 S 11 16 26 42 42
27 47
IP
12.00 to 12.45 CI 47 16 21 UDS
16 21 47
13.50 to 13.95 MI 38 NP S 17 20 25 45 45 NP
38
IP
18.00 to 18.45 GC 40 25 20 UDS 20
25 40
50 NP
19.50 to 19.95 GM 36 NP S 13 50 - >50
36
21.00 to 21.45 SM 36 NP S 12 30 50 80 80 NP
36
22.50 to 22.95 SM 35 NP S 9 21 50 71 71 NP
35
24.00 to 24.45 MI 49 NP S 9 28 50 78 78 NP
49
27.00 to 27.45 MI 38 NP S 25 49 50 99 99 NP
38 NMC
LL
PL
28.50 to 28.95 ML 28 NP 11 UDS 11 NP
28
50 NP
31.50 to 31.95 MI 36 NP S 40 50 - >50 36
11 NP
33.00 to 33.45 MI 37 NP 11 UDS 37
50 NP
34.50 to 34.95 GM 32 NP S 50 - - >50 32
50 NP
36.00 to 36.45 SM 41 NP S 22 50 - >50 41
IP
37.50 to 37.95 SC 31 20 S 49 52 - 52 52
20 31
IP
39.00 to 39.45 SC 31 18 S 50 - - >50 50
18 31
IP
40.00 to 40.45 0.00 32 22 S 50 - - >50 50
22 32
40.45
24 54
IP
1.50 to 1.95 CH 56 27 22 UDS 22
27 56
IP
3.00 to 3.45 CH 87 19 S 6 8 10 18 18
19 87
IP
7.50 to 7.95 CI 43 22 23 UDS
22 23 43
9.00 to 9.45 CH 54 21 S 28 40 50 90 90
IP
21 54
IP
10.50 to 10.95 CI 44 25 22 UDS 22
25 44
18.00 to 18.45 SM 31 NP S 6 21 50 71 71 NP
31
21.00 to 21.45 GM 35 NP S 3 24 50 74 74 NP
35
22.50 to 22.95 SM 36 NP S 8 28 50 78 78 NP
36
98
24.00 to 24.45 GM 40 NP S 15 48 50 98 NP
40
50 NP
31.50 to 31.95 MI 44 NP S 50 - - >50 44
50 NP
33.00 to 33.45 MI 47 NP S 40 50 - >50 47
50 NP
34.50 to 34.95 SM 38 NP S 50 - - >50 38
50 NP
36.00 to 36.45 GM 37 NP S 50 - - >50 37
23 60
1.50 to 1.95 CH 60 26 S 3 4 7 11 11 IP
26 60
27 IP
3.00 to 3.45 CH-CI 50 20 27 UDS
20 50
IP
4.50 to 4.95 CI 40 20 S 5 8 10 18 18
20 40
7.50 to 7.95 SC 55 22 S 7 14 19 33 IP
33
22 55
IP
9.00 to 9.45 CI 46 25 24 UDS 24
25 46
10.00 to IP
CI 39 23 S 10 18 24 42 42
10.45 23 39
11.00 to IP
CI 48 21 16 UDS 16
11.45 21 48
IP
12.00 to 12.45 CI 40 20 S 13 21 28 49 49
20 40
84 NP
15.00 to 15.45 SM 34 NP S 30 41 43 84
34
NP
31.50 to 31.95 SM 41 NP 17 UDS 17 41
NP
33.00 to 33.45 SM 37 NP S 31 43 50 93 50
37
IP
34.50 to 34.95 CI-CL 35 19 13 UDS
13 19 35
50 NP
36.00 to 36.45 MI 37 NP S 50 - - >50 37
50 NP
37.50 to 37.95 ML 33 NP S 50 - - >50 33
NP
39.00 to 39.45 SM 27 NP 19 UDS 27
19
75
425
4.75
2.00
110.00
160160
Project No.
100.00
90.00
032
80.00 0.00 to -0.50
Sheet No.
-1.50 to -1.95
70.00 -3.00 to -3.45
-4.50 to -4.95
-6.00 to -6.45
60.00
-7.50 to -7.95
-9.00 to -9.45
50.00 -10.00 to -10.45
-11.00 to -11.45
Percentage Finer
40.00 -12.00 to -12.45
-13.50 to -13.95
30.00 -15.00 to -15.45
-16.50 to -16.95
-18.00 to -18.45
20.00
10.00
0.00
2.00
4.75
0.002
0.075
0.425
75
425
4.75
2.00
110.00
160160
Project No.
100.00
90.00
033
80.00 -19.50 to -19.95
Sheet No.
-21.00 to -21.45
-22.50 to -22.95
70.00
-24.00 to -24.45
-25.50 to -25.95
60.00 -27.00 to -27.45
-28.50 to -28.95
50.00 -30.00 to -30.45
-31.50 to -31.95
Percentage Finer
-33.00 to -33.45
40.00 -34.50 to -34.95
-36.00 to -36.45
30.00 -37.50 to -37.95
-39.00 to -39.45
-40.00 to -40.45
20.00
10.00
0.00
2.00
4.75
0.002
0.075
0.425
75
425
4.75
2.00
110.00
160160
Project No.
100.00
90.00
034
80.00 0.00 to -0.50
Sheet No.
-1.50 to -1.95
70.00 -3.00 to -3.45
-4.50 to -4.95
-6.00 to -6.45
60.00
-7.50 to -7.95
-9.00 to -9.45
50.00 -10.50 to -10.95
-12.00 to -12.45
Percentage Finer
40.00 -13.50 to -13.95
-15.00 to -15.45
30.00 -16.50 to -16.95
-18.00 to -18.45
-19.50 to -19.95
20.00
10.00
0.00
2.00
4.75
0.002
0.075
0.425
75
425
4.75
2.00
160160
110.00
Project No.
100.00
90.00
035
Sheet No.
80.00 -21.00 to -21.45
-22.50 to -22.95
70.00 -24.00 to -24.45
-25.50 to -25.95
-27.00 to -27.45
60.00
-28.50 to -28.95
-30.00 to -30.45
50.00 -31.50 to -31.95
-33.00 to -33.45
Percentage Finer
40.00 -34.50 to -34.95
-36.00 to -36.45
30.00 -37.50 to -37.95
-39.00 to -39.45
-40.00 to -40.45
20.00
10.00
0.00
2.00
4.75
0.002
0.075
0.425
75
425
4.75
2.00
110.00
160160
Project No.
100.00
90.00
036
Sheet No.
80.00 0.00 to -0.50
-1.50 to -1.95
70.00 -3.00 to -3.45
-4.50 to -4.95
-6.00 to -6.45
60.00
-7.50 to -7.95
-9.00 to -9.45
50.00 -10.50 to -10.95
-12.00 to -12.45
Percentage Finer
40.00 -13.50 to -13.95
-15.00 to -15.45
30.00 -16.50 to -16.95
-18.00 to -18.45
-19.50 to -19.95
20.00
10.00
0.00
2.00
4.75
0.002
0.075
0.425
75
425
4.75
2.00
160160
110.00
Project No.
100.00
90.00
037
Sheet No.
80.00 -21.00 to -21.45
-22.50 to -22.95
70.00 -24.00 to -24.45
-25.50 to -25.95
-27.00 to -27.45
60.00
-28.50 to -28.95
-30.00 to -30.45
50.00 -31.50 to -31.95
-33.00 to -33.45
Percentage Finer
40.00 -34.50 to -34.95
-36.00 to -36.45
30.00 -37.50 to -37.95
-39.00 to -39.45
-40.00 to -40.45
20.00
10.00
0.00
2.00
4.75
0.002
0.075
0.425
75
425
4.75
2.00
110.00
160160
Project No.
100.00
90.00
038
80.00 0.00 to -0.50
Sheet No.
-1.50 to -1.95
70.00 -3.00 to -3.45
-4.50 to -4.95
-6.00 to -6.45
60.00
-7.50 to -7.95
-9.00 to -9.45
50.00 -10.00 to -10.45
-11.00 to -11.45
Percentage Finer
40.00 -12.00 to -12.45
-13.50 to -13.95
30.00 -15.00 to -15.45
-16.50 to -16.95
-18.00 to -18.45
20.00
10.00
0.00
2.00
4.75
0.002
0.075
0.425
75
425
4.75
2.00
110.00
160160
Project No.
100.00
90.00
039
-19.50 to -19.95
Sheet No.
80.00
-21.00 to -21.45
-22.50 to -22.95
70.00
-24.00 to -24.45
-25.50 to -25.95
60.00 -27.00 to -27.45
-28.50 to -28.95
50.00 -30.00 to -30.45
-31.50 to -31.95
Percentage Finer
-33.00 to -33.45
40.00 -34.50 to -34.95
-36.00 to -36.45
30.00 -37.50 to -37.95
-39.00 to -39.45
-40.00 to -40.45
20.00
10.00
0.00
2.00
4.75
0.002
0.075
0.425
0.560
0.540
0.520
0.500
Void Ratio (e)
0.480
0.460
0.440
0.420
0.400
0.380
0.360
0.10 1.00 Pc 10.00
2
Log (Pressure) kg/cm
0.540
0.520
0.500
Void Ratio (e)
0.480
0.460
0.440
0.420
0.400
0.380
0.10 1.00 Pc 10.00
0.580
0.560
0.540
Void Ratio (e)
0.520
0.500
0.480
0.460
0.440
0.420
0.10 1.00 Pc 10.00
Sample Designation
Denseness of Strata
Corrected SPT-'Nc'
at SPT termination
Depth from R.L.
IS Classification
Shrinkage Limit
Plasticity Index
Depth from RL
Swelling Index
SPT-N Values
Resistance (φ)
Consolidation
Cohesion (C)
Pressure (Pc)
Compression
Visual Identification of Soil
Plastic Limit
Liquid Limit
(<0.075mm)
(<0.002mm)
Water Table
Porosity (η)
(>4.75 mm)
(4.75mm to
Silt Factor
0.075mm)
Diff. Free
Hatching
Index Cc
Remarks
Shearing
Angle of
(FMC)
(WL)
(Wp)
Type
Bulk
Dry
(Ip)
Pre
2 2
m No. No. 0
% % % % % % % g/cc (%) % kg/cm Deg. kg/cm % %
0.00 to -0.50 D/S 3 14 83 56 18 38 CH 0.91
Filled up soil up to 1.50m
1
3
-3.00 to -3.45 14 14 - Vs S 26 13 61 43 19 24 CI 1.00
4
-4.50 to -4.95 5 Brownish high to medium to low UDS 19 12 69 39 22 16 CI 1.96 1.61 22 2.51 0.55 35.69 0.95 DS 0.14 24 22 10
plastic silty clay up to 8.00m
6
-6.00 to -6.45 52 52 - H S 0 34 66 40 17 24 CI 0.87
7
Tuu 0.40 17
-7.50 to -7.95 8 UDS 9 19 71 43 20 23 CI 1.96 1.68 17 2.51 0.49 32.96 0.82 DS 0.13 23 30 10
9
-9.00 to -9.45 71 71 - H S 6 16 78 52 26 26 CH 0.79
10 Brownish high to medium plastic
-10.00 to -10.45 silty clay up to 12.00m UDS 6 18 75 44 24 20 CI 1.93 1.58 22 2.51 0.58 36.86 0.85 DS 0.13 23 0.195 1.82 24 10
11
-11.00 to -11.45 90 90 - H S 2 16 82 92 22 70 CH 0.81
12
-12.00 to -12.45 UDS 13 26 61 35 NP NP MI-ML 1.93 1.64 18 2.57 0.57 36.35 0.87 DS 0.06 27 N.O.
13
Brownish non plastic clayey silt to
-13.50 to -13.95 111 46 - Vd silty sand & gravels up to 15.00m S 20 51 29 25 NP NP SM 0.99
14
15
-15.00 to -15.45 D/S 0 71 29 36 NP NP SM 1.63
16
18
-18.00 to -18.45 95 50 20cm Vd S 63 14 23 36 NP NP GM 1.20
19
-19.50 to -19.95 81 42 - D 20
S 71 10 19 36 NP NP GM 1.80
21
-21.00 to -21.45 >50 41 12cm Vd 22.00 S 44 38 18 36 NP NP GM 2.28
Blackish non plastic silty sand to
22 silty gravles up to 28.50m
24
-24.00 to -24.45 >50 45 10cm Vd S 46 37 17 34 NP NP GM 2.52
25
27
-27.00 to -27.45 80 35 20cm Vd S 65 18 17 33 NP NP GM 1.66
28
30
Brownish non plastic clayey silt up
-30.00 to -30.45 >50 83 10cm Vd to 31.00m S 1 27 72 45 NP NP MI 0.79
31
-31.50 to -31.95 UDS 13 63 24 36 NP NP SM 1.98 1.61 23 2.58 0.60 37.61 1.13 DS 0.00 31 N.O.
32
33
-33.00 to -33.45 >50 36 10cm Vd S 23 49 28 33 NP NP SM 1.10
Brownish non plastic silty sand &
34 gravels up to 36.00m
-34.50 to -34.95 UDS 25 40 35 40 NP NP SM 1.98 1.74 14 2.58 0.49 32.79 1.06 N.O.
35
36
-36.00 to -36.45 >50 60 05cm Vd S 3 70 27 31 NP NP SM 1.68
Blackish non plastic silty sand up to
37 38.00m
Name of Work :- Proposed site for Highrise Textile Market at F.P.No: 41+42, T.P.S
No: 19(Parvat-Magob), Ta: City, Dist: Surat
at SPT termination
Depth from R.L.
IS Classification
Shrinkage Limit
Plasticity Index
Depth from RL
Swelling Index
SPT-N Values
Resistance (φ)
Consolidation
Cohesion (C)
Pressure (Pc)
Compression
Visual Identification of Soil
Plastic Limit
Liquid Limit
(<0.075mm)
(<0.002mm)
Water Table
Porosity (η)
(>4.75 mm)
(4.75mm to
Silt Factor
0.075mm)
Diff. Free
Hatching
Index Cc
Remarks
Shearing
Angle of
(FMC)
(WL)
(Wp)
Type
Bulk
Dry
(Ip)
Pre
2 2
m No. No. % % % % % % % g/cc (%) % kg/cm Deg. kg/cm % %
0
0.00 to -0.50 D/S 1 18 81 45 23 22 CI 0.92
Filled up soil up to 1.50m
1
4
Brownish to yellowish medium
-4.50 to -4.95 10 10 - St plastic silty clay up to 5.50m S 1 6 93 45 24 21 CI 0.51
5
6
-6.00 to -6.45 UDS 0 20 79 31 20 12 CL 1.91 1.66 15 2.51 0.51 33.92 0.63 DS 0.13 23 - 10
Brownish low to high plastic silty
7
clay up to 8.00m
-7.50 to -7.95 47 47 - H S 16 15 69 60 23 37 CH 0.86
8
Tuu 0.42 16
9
-9.00 to -9.45 UDS 1 10 89 49 18 31 CI 1.93 1.59 21 2.52 0.58 36.68 0.81 DS 0.14 23 26 10
12
-12.00 to -12.45 UDS 12 5 84 47 16 31 CI 1.98 1.63 21 2.54 0.56 35.81 0.61 DS 0.14 23 0.197 1.69 N.O.
13
16
24
-24.00 to -24.45 78 61 - D S 0 19 80 49 NP NP MI 0.67
27
-27.00 to -27.45 99 61 - Vd S 8 36 57 38 NP NP MI 1.01
28
30
-30.00 to -30.45 >50 32 13cm Vd S 12 59 29 30 NP NP SM 1.46
31
34
36
-36.00 to -36.45 >50 52 06cm Vd S 3 48 50 41 NP NP SM 1.08
37
40
-40.00 to -40.45 >50 56 05cm Vd S 7 75 18 32 22 10 SC 2.00
40.45
Name of Work :- Proposed site for Highrise Textile Market at F.P.No: 41+42, T.P.S
No: 19(Parvat-Magob), Ta: City, Dist: Surat
at SPT termination
Depth from R.L.
IS Classification
Shrinkage Limit
Plasticity Index
Depth from RL
Swelling Index
Void Ratio (e)
SPT-N Values
Resistance (φ)
Consolidation
Cohesion (C)
Pressure (Pc)
Compression
Visual Identification of Soil
Liquid Limit
Plastic Limit
(<0.075mm)
(<0.002mm)
Water Table
Porosity (η)
(>4.75 mm)
(4.75mm to
Silt Factor
0.075mm)
Diff. Free
Hatching
Index Cc
Shearing
Remarks
Angle of
(FMC)
(WL)
(Wp)
Type
Bulk
Dry
(Ip)
Pre
2 2
m No. No. % % % % % % % g/cc (%) % kg/cm Deg. kg/cm % %
0
0.00 to -0.50 D/S 3 21 76 54 24 29 CH 1.02
Blackish high plastic silty clay up
1 to 2.00m
-1.50 to -1.95 UDS 1 13 86 56 27 29 CH 1.97 1.61 22 2.51 0.56 35.80 0.80 28 30
2
Brownish high plastic silty clay
3
with sand & gravels up to 4.00m
-3.00 to -3.45 18 18 - Vs S 12 8 80 87 19 68 CH 0.68
4
Yellowish non plastic clayey silt
-4.50 to -4.95 UDS 4 27 69 42 NP NP MI 1.90 1.55 23 2.55 0.64 39.19 0.69 DS 0.05 26 - N.O.
5
with sand up to 5.50m
6
-6.00 to -6.45 39 27 - D S 9 15 76 49 29 20 MI 0.96
Yellowish medium plastic clayey
7
silt with sand up to 7.50m
-7.50 to -7.95 UDS 5 10 84 43 22 21 CI 1.92 1.56 23 2.51 0.61 37.86 0.75 DS 0.14 23 26 40
8
-10.50 to -10.95 UDS 14 16 70 44 25 19 CI 1.93 1.58 22 2.51 0.59 37.10 0.89 DS 0.14 23 0.156 2.35 N.O.
11
12
-12.00 to -12.45 >50 - 09cm Vd S 8 26 66 38 NP NP MI 0.91
Brownish non plastic clayey silt
13
with silty sand up to 15.00m
-13.50 to -13.95 UDS 15 68 17 46 NP NP SM 1.92 1.81 6 2.55 0.41 29.06 1.29 DS 0.00 32 N.O.
14
15
-15.00 to -15.45 >50 - 10cm Vd S 7 71 22 35 NP NP SM 1.25
16
-16.50 to -16.95 UDS 1 82 17 27 NP NP SM 1.95 1.71 14 2.54 0.49 32.68 1.66 DS 0.00 32 N.O.
17
18
-18.00 to -18.45 71 34 24cm Vd 19.00 S 3 68 29 31 NP NP SM 1.24
Brownish non plastic clayey silt
19 with silty sand up to 22.50m
-19.50 to -19.95 UDS 2 76 22 34 NP NP SM 1.98 1.75 13 2.56 0.46 31.60 2.33 N.O.
20
21
-21.00 to -21.45 74 30 27cm Vd S 56 20 24 35 NP NP GM 2.04
22
24
-24.00 to -24.45 98 38 24cm Vd S 64 15 22 40 NP NP GM 2.01
25
27
-27.00 to -27.45 >50 64 06cm Vd S 60 10 30 42 NP NP GM 1.48
28
30
-30.00 to -30.45 >50 36 11cm Vd S 6 72 21 36 NP NP SM 1.98
31
Blackish non plastic silty sand to
-31.50 to -31.95 >50 58 15cm Vd silty gravels to clayey siltup to S 4 35 60 44 NP NP MI 0.92
32
investigation depth
33
-33.00 to -33.45 >50 83 10cm Vd S 3 33 64 47 NP NP MI 0.94
34
36
-36.00 to -36.45 >50 41 08cm Vd S 47 17 36 37 NP NP GM 1.40
37
39
-39.00 to -39.45 >50 57 05cm Vd S 43 20 37 37 NP NP GM 1.06
40
-40.00 to -40.45 >50 48 06cm Vd S 43 26 31 35 NP NP GM 1.35
40.45
Name of Work :- Proposed site for Highrise Textile Market at F.P.No: 41+42, T.P.S
No: 19(Parvat-Magob), Ta: City, Dist: Surat
at SPT termination
Depth from R.L.
IS Classification
Shrinkage Limit
Plasticity Index
Depth from RL
Swelling Index
Void Ratio (e)
SPT-N Values
Resistance (φ)
Consolidation
Cohesion (C)
Pressure (Pc)
Compression
Visual Identification of Soil
Liquid Limit
Plastic Limit
(<0.075mm)
(<0.002mm)
Water Table
Porosity (η)
(>4.75 mm)
(4.75mm to
Silt Factor
0.075mm)
Diff. Free
Hatching
Index Cc
Shearing
Remarks
Angle of
(FMC)
(WL)
(Wp)
Type
Bulk
Dry
(Ip)
Pre
2 2
m No. No. % % % % % % % g/cc (%) % kg/cm Deg. kg/cm % %
0
0.00 to -0.50 D/S 7 15 78 60 23 37 CH 0.93
Blackish high plastic silty clay up
1 to 2.00m
-1.50 to -1.95 11 11 - St S 3 19 78 60 26 34 CH 0.98
2
3
-3.00 to -3.45 UDS 6 7 86 50 20 29 CH-CI 1.93 1.53 27 2.51 0.65 39.30 0.59 DS 0.19 20 24 55
4
Yellowish high to medium plastic
-4.50 to -4.95 18 18 - Vs S 13 35 52 40 20 19 CI 1.32
5
silty clay with sand up to 7.50m
Tuu 0.48 11
6
-6.00 to -6.45 UDS 13 14 73 49 27 22 CI 1.95 1.61 21 2.53 0.57 36.31 0.99 DS 0.13 24 26 40
9
-9.00 to -9.45 UDS 9 16 75 46 25 21 CI 1.97 1.59 24 2.51 0.57 36.44 0.80 DS 0.14 23 26 20
10
-10.00 to -10.45 42 42 - H S 13 23 63 39 23 16 CI 1.03
Yellowish high to medium plastic
11
-11.00 to -11.45 silty clay ith sand & gravels up to UDS 17 33 51 48 21 26 CI 1.94 1.68 16 2.52 0.50 33.44 1.07 DS 0.15 23 N.O.
13.50m
12
-12.00 to -12.45 49 49 - H S 8 36 57 40 20 20 CI 1.16
13
-13.50 to -13.95 UDS 5 70 25 30 NP NP SM 1.98 1.78 11 2.55 0.44 30.40 1.08 DS 0.00 33 N.O.
14
15
-15.00 to -15.45 84 35 - Vd S 16 68 16 34 NP NP SM 1.63
16
-16.50 to -16.95 UDS 17 16 68 39 NP NP MI 1.99 1.58 26 2.57 0.63 38.54 1.26 N.O.
17
18
-18.00 to -18.45 >50 51 10cm Vd S 41 46 13 32 NP NP SM 1.95
19
20.00
-19.50 to -19.95 >50 60 08cm Vd S 44 43 14 35 NP NP GM 2.01
20
21
-21.00 to -21.45 >50 47 10cm Vd S 37 44 19 29 NP NP SM 2.15
22
27
-27.00 to -27.45 >50 63 06cm Vd S 27 54 19 42 NP NP SM 1.74
28
-28.50 to -28.95 UDS 14 12 74 36 NP NP MI 1.96 1.55 26 2.56 0.65 39.38 0.88 N.O.
29
30
-30.00 to -30.45 >50 39 10cm Vd S 18 57 26 44 NP NP SM 1.67
31
-31.50 to -31.95 UDS 16 60 24 41 NP NP SM 1.96 1.67 17 2.56 0.54 34.89 1.29 N.O.
32
33
-33.00 to -33.45 93 97 06cm Vd S 24 51 25 37 NP NP SM 1.58
34
-34.50 to -34.95 UDS 7 4 89 35 19 17 CI-CL 1.97 1.74 13 2.52 0.45 30.89 0.69 N.O.
35 Yellowish medium to low plastic
silty clay up to 36.00m
36
-36.00 to -36.45 >50 - 04cm Vd S 3 8 89 37 NP NP MI 0.77
37
40
-40.00 to -40.45 >50 - 05cm Vd S 10 67 23 34 NP NP SM 1.76
40.45
Name of Work :- Proposed site for Highrise Textile Market at F.P.No: 41+42, T.P.S
No: 19(Parvat-Magob), Ta: City, Dist: Surat
ML: Inorganic silts and very fine sands rock flour, silty or clayey fine sands or
clayey silts with none to low plasticity
MI: Inorganic silts, silty or clayey fine sands or clayey silts of medium plasticity
CL: Inorganic clays, gravelly clays, sandy clays, silty clays, lean clays of low
plasticity
CI: Inorganic clays, gravelly clays, sandy clays, silty clays, lean clays of
medium plasticity
Pt: Peat & other highly organic soils with very high compressibility