Escolar Documentos
Profissional Documentos
Cultura Documentos
AlarmLine™ Addressable
Linear Heat Detector
P/N 73-100001-003 TM
K-73-02
FEATURES
• UL Listed
• FM Approved
• CSFM
• MEA (pending)
• Low-cost interface between AlarmLine™ sensor
cable and control panel accepting SmartOne™
addressable devices
• Up to 255 Addressable AlarmLine Modules (AAM)
per addressable loop
• Real-time monitoring
• Software adjustable alarm set point
• Optional pre-alarm and overheat output
configuration selections
• Three cable styles (standard, nylon, bronze braided)
• Sensor cable restorable up to 257°F
• Full supervision for short and open circuits
• Two-color status-LED display for alarm and trouble DESCRIPTION
conditions
The AlarmLine Addressable Linear Heat Detector
• Intrinsically safe option
provides early detection of fire or overheat condition in
• Flexibility in zoning
protected areas or equipment. It is especially suited for
• Enhanced response time confined areas or environments where adverse ambient
conditions cause other detection devices to be unreliable
or difficult to use. The detector consists of two major
components: A sensor cable and an Addressable
AlarmLine Module (AAM).
The AAM is used with any intelligent control panel that
accepts SmartOne devices.
APPLICATIONS
• Open-area protection
• Cable trays
• Rack storage
• Freezer warehouses
• Belt conveyers
• Floating roof fuel tanks
• Cooling towers
• Dust collectors
• Waste fuel drum storage
• Power distribution apparatus
• Escalators
• Tunnels
• Mines
• Hangars
BENEFITS
NEGATIVE TEMPERATURE
Application Flexibility: Allows installation at point of COEFFICIENT MATERIAL
-2-
For further information on installation and configuration of
Bronze
the AAM, please refer to the AlarmLine Addressable Description
Standard Nylon Coated
Braided
Linear Heat Detector Installation, Operation, and Sensor Sensor
Sensor
Maintenance Manual, P/N 06-235820-003.
Service Life Up to 212ºF Up to 212ºF Up to 212ºF
The Addressable AlarmLine Module is available using (100ºC) = 30 (100ºC) = 30 (100ºC) = 30
the following part numbers: years @ 257ºF years @ 257ºF years @ 257ºF
(125ºC) = 24 (125ºC) = 24 (125ºC) = 24
hours. hours. hours.
73-100001-003 Self Restores Self Restores Self Restores
Module with operating temperature range of -40º Fº to below 257ºF below 257ºF below 257ºF
(125ºC) (125ºC) (125ºC)
140º F (-40º C to 60º C). Mounted on a 4-inch square Above 374ºF Above 374ºF Above 374ºF
faceplate. AAM mounts in a 4-inch square backbox, (190ºC) is the (190ºC) is the (190ºC) is the
destructive destructive destructive
2-1/8-inches deep. temperature. temperature. temperature.
CABLE SPECIFICATIONS
SENSOR MOUNTING HARDWARE
Three types of standard mounting hardware (master
Bronze
Description
Standard Nylon Coated
Braided
clamp, flange clamp, nylon cable tie) for AlarmLine
Sensor Sensor permit safe, secure sensor cable installation in most
Sensor
applications. Other mounting means may be used as
Part Number : 73-117068-013 73-117068-016 73-117068-019 required by the specific application. The sensor should
Length: 656 ft. (200 m) 656 ft. (200 m) 656 ft. (200 m)
Weight: 7 lbs. (3.2 kg) 7 lbs. (3.2 kg) 7 lbs. (3.2 kg) be supported at a minimum of ten foot intervals on
straight runs when under tension, and more as conditions
Part Number : 73-117068-113 73-117068-116 73-117068-119
Length: 3280 ft. (1000 m) 3280 ft. (1000 m) 3280 ft. (1000 m) dictate at corners and transition points to provide suitable
Weight: 35 lbs. (14.5 kg) 35 lbs. (14.5 kg) 35 lbs. (14.5 kg) strain relief. Local codes or conditions may also require
Jacket Blue PVC Black nylon Phosphor
the sensor to be supported at closer intervals. Refer to
Construction extrusion over bronze braid the AlarmLine Addressable Linear Heat Detector
blue PVC over blue PVC
Installation, Operation, and Maintenance Manual, P/N
External 0.117 in. 0.153 in. 0.153 in. 06-235820-003 for specific mounting information.
Diameter (3 mm) (3.9 mm) (3.9 mm)
-3-
AAM SPECIFICATIONS UL Listed and FM Class I, Division I, Groups A, B, C, D
Approvals Class II, Division I, Groups E, F, G: Class
III, Division I
Specification Value
Operating Tempera- -4ºF (-20ºC) to 140ºF (60ºC)
Part Number 73-100001-003 ture Range
Humidity 5 -95% R.H.
Supply Voltage P.C. Line, 16.5 to 27.5 Vdc
Terminals Will accept up to #12 AWG
Current Consumption, 425 µAmps Working Voltage 6V
Standby Maximum Voltage 7.5V
Current Consumption, Alarm 440 µAmps Fuse Rating 100 mA
Leakage Current 1 mA maximum at 6V
Current Consumption,Fault 425 µAmps
End-To-End Resis- 145 ohm maximum
Noise Performance Withstands 5% RMS 60 Hz tance 90 ohm minimum
supply noise or 1 Vrms 60 Enclosures 73-117068-732 holds 2 barriers
Hz sensor noise with 73-117068-733 holds 5 barriers
negligible performance 73-117068-734 holds 12 barriers
range. RFI immunity at 10 73-117068-735 holds 24 barriers
V/meter field strength over
SETTING THE ALARM TEMPERATURE
the band of 20 to 900 MHz
When determining the alarm temperature setting, the
Normal: Slow flash GREEN designer must take into account environmental factors
every nine (9) seconds that may affect the overall response of the system. By
Pre-Alarm: Slow flash RED accounting for these factors, the designer minimizes
every nine (9) seconds unwanted alarms. Below is a step by step procedure
LED Pulse Modes
which instructs the designer in selection of the proper
Alarm: Fast flash RED every alarm trip points.
two (2) seconds
The required alarm temperature and the correct alarm
Trouble: Off configuration setting for the AAM are determined using
the AlarmLine nomogram(s).
Operating Temperature -40°F to 140°F
Range (-40°C to 60°C) Measurements are in feet/fahrenheit or meters/
centigrade.
INTRINSIC SAFETY BARRIERS The use of the nomogram requires two known factors:
In classified hazardous areas where potentially explosive • Maximum ambient temperature of the alarm zone.
vapors, dust, or fibers exist, AlarmLine cable must (Scale A).
installed using an intrinsic safety barrier. The barrier (P/N • The total length of the sensor cable to be used.
73-117068-031) is a shunt diode safety barrier which (Scale L).
limits the current and voltage in the sensor cable to safe The resistance change required to create an alarm can
levels. Each barrier handles two conductors, so two be a result of either a predetermined minimal increase in
barriers are needed for each sensor cable. The barriers temperature over the entire length of the sensor, or a
are designed to mount in separate weathertight significant increase on a shorter section of cable. The
enclosures. The intrinsic safety barrier’s specifications alarm temperature in either case is determined only after
are as follows: the alarm trip switch position for the entire sensor length
is known.
A shorter section of sensor cable exposed to an overheat
condition will require a higher temperature to achieve an
alarm than a longer length of sensor cable exposed to
the same overheat condition.
The maximum length of sensor cable per zone depends
on the maximum ambient temperature defined on the
nomogram. Regardless of ambient, however, the
maximum length of cable connected to a single AAM is
3280 ft. (1000 m). If cable length exceeds 3280 ft., the
-4-
alarm condition could be reached at room temperature
KIDDE-FENWAL, INC.
(70º F (20º C)) for most switch settings. Refer to the 400 MAIN ST. ASHLAND, MA 01721
UL
TM
AlarmLine Addressable Linear Heat Detector Installation,
R
WHT
ORN
RED
BLU
Configuration Ambient Alarm Cable A B A B
Setting Temp. (F) Temp. (F) Length (Ft.)
TB1 4 3 2 1 4 3 2 1 TB2
3200
ORANGE
2900
WHITE
2600
BLUE
RED
2300
2000
1650
INTERCONNECT CABLE
1300 EARTH P.C.LINE P.C.LINE 16 AWG, 4 CONNECTOR
1000
GROUND OUT IN (IF REQUIRED)
1 825
650
2
500
3 95 WEATHERPROOF
75 4 3 2 1
105 JUNCTION BOX
4 300 4 3 2 1
85
115
265 (IF REQUIRED)
5 95 230
120 200
6 105 165
130
115 130
7 140 SENSOR CABLE
120 100
8 150 80
130
140
160 65 Figure 4. Wiring the AAM to a Panel
9 50
165
150
10 175
160 35
185
ADDRESSABLE ALARMLINE MODULE WIRING
165 25
11 175 195
185 205 20
12 195 210
220 The Addressable AlarmLine Module (P/N 73-100001-
13 230
240 10 003) may connected to any fire control panel that accepts
14 250
15
257 SmartOne addressable devices. The module is wired
16
5
directly to the SLC loop of the panel as shown in Figure
3
4. Refer to the AlarmLine Addressable Linear Heat
Figure 2. Example for Type “T” Cable (Feet/Fahrenheit) Detector Installation, Operation, and Maintenance
Manual, P/N 06-235820-003 for complete wiring
S A T L
information.
NEMA-4 ENCLOSURE
Alarm Maximum Specified Sensor
Configuration Ambient Alarm Cable
Settng Temp. (F) Temp. (F) Length (Ft.)
The NEMA-4 polycarbonate enclosure (P/N 73-100003-
3200
2900
2600
001) is designed to mount the Addressable AlarmLine TM
2300
2000 Module in areas requiring additional protection from wet
and/or dusty environments. This enclosure is rated as
1650
1300
1000
825
follows:
1
5
85
95
115
265
230 • NEMA Type 4, Type 4X, Type 6, Type 12, and Type
6 105
120
130
200
165 13
130
• CSA Type 4, Type 4X, Type 6, Type 12, and Type 13
115
7 140
120 100
150 80
8
9
130
140
160 65 • Flammability rating UL94-5V
• IEC 529, IP66
165 50
150
10 175
160 35
185
11
165
175 195 25
20
The enclosure is equipped with a clear cover so that the
185 205
12 195 210
220
AAM alarm/trouble status indicator LED can be viewed.
13
14
230
240
250
10
The cover also provides a molded-in wire-lead hole for
15
257
5
tamper resistant installation. Mounting holes for the
16
3 enclosure are molded directly under the cover screws. A
Figure 3. Example for Type “T” Cable (Feet/Fahrenheit) cover gasket assures watertight and dust-tight seals.
-5-
The impact-resistant, glass-filled, polycarbonate
enclosure material is easily punched, drilled, or sawed to
provide access for field wiring.
For further installation information, refer to the AlarmLine
Addressable Linear Heat Detector Installation, Operation,
and Maintenance Manual, P/N 06-235820-003.
ENCLOSURE
4.330
BRACKET
AAM
4.330
COVER
TM
e
Lin
MOUNTING HOLE rm
Ala
FOR #8 SCREW (TYP.)
TM
SELF-TAPPING SCREWS e
On
art
Sm
TINNERMAN CLIPS
#8-32 SCREWS
CROSS-POINT, CAPTIVE
COVER SCREWS