ssi62018 {992K Wee! Loader H4C00001-UP (MACHINE) POWERED BY C32 Engine(SEBP4140 - 43) - Documentacin
Ferreyros rn Service Information System
Pantalla anterior
Bienvenido: r080ac12
< Producto: WHESL LOADER
Modelo: 992K WHEFL
Configuracién: 992K W'
Pruebas y Ajustes
992K Wheel Loader Electrohydraulic System
Namero de medio -RENR9788-05 fecha de publicacién -01/12/2013, Fecha de actualizacién -10/12/2013
102920559
Implement Cycle Time - Check
SMCS - 6000-535-VF
WARNING
Sudden movement or accidental starting of the machine can cause
personal injury or death to persons on or near the machine.
To prevent personal injury or death, perform the following:
Park the machine on a smooth, level surface.
Lower the work tool to the ground and engage the parking brake.
Stop the engine and remove the key.
Block the wheels and install the steering frame lock.
The test for the implement cycle time is used to verify a complaint about slow speed. This test will also help to
determine whether all functions are slow or only one function is slow.
If any functions are slow, the implement cycle times must be checked in order to determine the faulty system.
Note: For all cycle time tests, the bucket must be empty.
1, Move the machine to an open area so that the bucket can be fully raised. Park the machine on a smooth,
level surface.
2. Connect the steering frame lock link.
3. Engage the parking brake.
4, Shift the transmission to neutral
5, Start the engine and warm the hydraulic oil to 65 + 3°C (150 + 5°F)
hitpsss.cat comisisweblsiswebitechdec:techdoc_print_page.jeprelurmurt=Isewob/siswebmediasearchimediaheaderinfofameseljep&calledpage=l... 1/2ssi62018
6.
7.
10.
ML
12.
13.
14,
15.
{992K Wee! Loader H4C00001-UP (MACHINE) POWERED BY C32 Engine(SEBP4140 - 43) - Documentacin
Position the bucket so that the bottom of the bucket is flat on the ground.
Rum the engine to high idle. Maintain high idle for the test.
. Move the lift control lever to the RAISE position, Hold the lift control lever in the full RAISE position
until the lift cylinders reach the full RAISE position. Record the lift time from the ground to the full
RAISE position.
The lift time should be 9.8 seconds,
Lower the bucket until the bucket is barely off the ground. Set the lower kickout.
Raise the bucket to the maximum height.
With the engine at high idle, move the lift control lever to the full LOWER DETENT position, Record the
time from the full RAISE position to the lower kickout position at the ground.
The time should be 3.6 seconds,
Move the bucket to the full RAISE position, Position the bucket to the full TILT BACK position.
With the engine at high idle, move the tilt control lever to the full DUMP position, Hold the tilt control
lever in this position until the bucket is at the full DUMP position. Record the time to the full DUMP
position,
The time should be 3.3 seconds,
Position the bucket approximately 300 mm (12 inch) above the ground with the bottom parallel to the
ground.
With the engine at high idle and with the bucket in a level position, move the tlt control lever to the full
TILT BACK position. Hold the tilt control lever in this position until the bucket is against the stop. Record
the time from the level position to the full TILT BACK position.
The time should be 3.0 seconds,
hitpsss.cat.comisisweblsswebitechdoctecndoc_print_page jeprelurnur=lseweb/siswebimediasearchimediaheaderinfof-ameselepScallecpage:
Fri2un 15 2018 22:34:41 GMT-0500 (hora esténder de Pers)
roaoaci2
22.