Escolar Documentos
Profissional Documentos
Cultura Documentos
TABLE OF CONTENTS
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
Serial #
You can find them on a label on the side of each unit.
Dealer's Name
1. Safety Precautions Date Purchased
■ Staple your receipt to this page in the event you need
2. Operating Instructions it to prove date of purchase or for warranty issues.
PRECAUTION
• Contact the authorized service technician for repair or
maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young
children or invalids without supervision.
• Young children should be supervised to ensure that
they do not play with the air conditioner.
• When the power cord is to be replaced, replacement
work shall be performed by authorized personnel only
using only genuine replacement parts.
• Installation work must be performed in accordance with
the National Electric Code by qualified and authorized
personnel only.
2
Safety
Precautions Precautions
To prevent injury to the user or other people and property damage, the following instructions must
ENGLISH
be followed.
■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.
CAUTION This symbol indicates the possibility of injury or damage to properties only.
WARNING
■ Installation
Always install the expansion panel(s). Do not place the power cord near a heater.
• No installation may cause fire and electric • It may cause fire and electric shock.
shock accident.
Do not use the power cord near flammable Do not disassemble or modify products.
gas or combustibles such as gasoline,
benzene, thinner, etc.
• It may cause explosion or fire. • It may cause failure and electric shock.
Gasolin
3
■ Operation
Plug in the power plug Do not operate or stop the Do not damage or use an
properly. unit by inserting or pulling unspecified power cord.
out the power plug.
• Otherwise, it will cause • It will cause electric shock or • It will cause electric shock or
electric shock or fire due to fire due to heat generation. fire.
heat generation or electric
shock.
ON
Do not modify power cord Do not share the outlet with Always plug into a
length. other appliances. grounded outlet.
• It will cause electric shock or • It will cause electric shock or • No grounding may cause
fire due to heat generation. fire due to heat generation. electric shock (See
Installation Manual).
Unplug the unit if strange Do not use the socket if it is Do not operate with wet
sounds, odors, or smoke loose or damaged. hands or in damp
come from it. environment.
• Otherwise it may cause fire • It may cause fire and electric • It will cause electric shock.
and electric shock accident. shock.
4
Do not allow water to run Leave the door closed while Do not operate the air
into electric parts. the air conditioner is conditioner if you smell gas.
running.
• It will cause failure of machine • It is not designed to cool the • It may cause explosion, fire,
or electric shock. entire house. and burn.
ENGLISH
CAUTION
■ Installation
Never touch the metal parts Do not block the inlet or Ensure that the outer case
of the unit when removing outlet. is not damaged by age or
the filter. wear.
• They are sharp and may • It may cause failure of • If leaving appliance damaged,
cause injury. appliance or accident. there is concern of damage
due to the falling of product.
■ Operation
Be cautious not to touch the Hold the plug by the hand Turn off the main power
sharp edges when (not the cable) when taking switch when not using it for
installing. it out. a long time.
• It may cause injury. • It may cause electric shock • Prevent accidental startup
and damage. and the possibility of injury.
Sharp
edges
5
Do not place heavy object If water enters the product, Do not clean the air
on the power cord and take turn off the the power switch conditioner with water.
care so that the cord should of the main body of appliance.
not be pressed. Contact service center after
taking the power-plug out
from the socket.
• There is danger of fire or • Water may enter the unit and
electric shock. degrade the insulation. It may
cause an electric shock.
Turn off the power and Do not put a pet or house Do not use this appliance for
breaker firstly when plant where it will be special purposes such as
cleansing the unit. exposed to direct air flow. cooling pets, foods, precision
machinery, or objects of art.
• Since the fan rotates at high • This could injure the pet or • It is an air conditioner, not a
speed during operation, it plant. precision refrigeration system.
may cause injury.
Always insert the filter Use a soft cloth to clean. Do Do not drink water drained
securely. not use wax, thinner, or a from air conditioner. / Do
Clean it every two weeks. strong detergent. not direct airflow at room
occupants only.
• Operation without filters will • The appearance of the air • It contains containments and
cause failure. conditioner may deteriorate, will make you sick. / This
change color, or develop could damage your health.
surface flaws.
x
Wa Thinner
6
ENGLISH
Controls
■ HEATER ( ) LAMP
When the unit sets heating operation condition, the
green lamp is lighted.
When the frost settles on the heat exchanger of the
outside, defrosting is made automatically and the
green lamp is turned off.
The unit may give a "hiss" and the fan motor stops for
1 to 10 minutes.
This should not be regarded as a problem.
After defrosting, the heating operation begins again.
■ OPERATION
Thermostat Operation OFF ( o ) : Turns the air conditioner off.
LOW FAN ( ) : Permits the low fan speed
operation without cooling
(heating).
LOW COOL ( ) : Permits cooling with the low fan
Heater speed operation.
Warmer Cooler HIGH COOL ( ) : Permits cooling with the high
Thermostat Operation fan speed operation.
LOW HEAT ( ) : Permits heating with the low
fan speed operation.
■ AUTO SWING (Optional)
HIGH HEAT ( ) : Permits heating with the high
ON ( ) : Air swing is operated while OPERATION fan speed operation.
knob is set to the COOL or HEAT position.
OFF ( ) : Stops the operation of air swing. CAUTION : When the air conditioner has
been performed its cooling operation and
is turned off or set to the fan position, wait
at least 3 minutes before resetting to the
cooling operation again.
9
Operating
Instructions Remote Control Operation
Controls
CAUTION: The Remote Control unit will not function properly if strong light strikes the sensor
window of the air conditioner or it there are obstacles between the Remote Control unit and the
air conditioner.
1. POWER BUTTON
Operation starts, when this button is pressed and stops when you press the button again.
2. AUTO SWING (Optional)
The vertical louver swings horizontally by the automatic system and stops when you press the button again.
3. ROOM TEMPERATURE SETTING BUTTON
Control the room temperature within a range of 16°C to 30°C
4. FAN SPEED SELECTOR
Select the fan speed in three steps {High[F3] → Low[F1] → Med[F2] → High[F3]...}.
5. OPERATION MODE SELECTION BUTTON
Select Cooling, Fan, or Dehumidification mode with this button.
6. ON/OFF TIMER BUTTON
Set the time of starting and stopping operation. The timer is set by 1 hour.
7. SIGNAL RECEIVER
AUTO RESTART
In failure of electric power, the unit runs as previous setting operation.
10
Operating
Instructions Adjusting the Air Flow Direction
Additional controls and important information.
ENGLISH
Ventilation
The ventilation lever must be in the CLOSE position in order to maintain the best cooling conditions.
When fresh air is necessary in the room, set the ventilation lever to the OPEN position.
The damper is opened and room air is drawn out.
Part B
Part A
Air Direction
The direction of air can be controlled whenever you want to cool by adjusting the horizontal louver and the
vertical louver.
• HORIZONTAL AIR DIRECTION CONTROL
To control horizontal direction of air flow, press the air flow
direction control button and the air flow will be swept
horizontally by the automatic air-swing system.
If you want to stop the air flow from moving, press the button
again at the desired position of the vane.
11
How to Attach Drain Pan (Some Models)
The air conditioner employs a proper drain method whereby the condensed water (moisture removed from the
air) is drained to the outside.
In very humid weather, (and for reverse cycle models in the reverse mode) excessive condensate water removed
from the air may cause some water to collect. To remove this excess water you can install the drain pan as
detailed below. CABINET
1. Take the drain pan which is located in the air discharge.
2. Remove the hole rubber from the base-pan (for some models).
3. Install the drain pan to the right corner of the cabinet with 4 (or 2) DRAIN
screws. PAN
4. Connect the drain hose to the outlet located at the bottom of the SCREW
drain pan.You can purchase the drain hose or tubing locally to DRAIN HOSE
satisfy your particular needs. (Drain hose is not supplied).
DRAIN ELBOW
DRAIN HOSE
Operating
Instructions Adjusting the Air Flow Direction
TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET.
Outdoor Coils
The coils on the outdoor side of the air conditioner should be checked
regularly. If they are clogged with dirt or soot they may be professionally
steam cleaned, a service available through a dealer.
12
Care and
Maintenance Care and Maintenance
ENGLISH
Air Filter Cleaning
The air filter should be checked at least twice a month to see if cleaning is necessary. Trapped particles in the
filter will build up and block the airflow. This reduces the cooling capacity and also causes an accumulation of
frost on the cooling coils.
1. Open the inlet grille upward by pulling out the bottom of the inlet grille.(a)
In another case, you can open the inlet grille downward by pulling out the top of the inlet grille.(b)
2. Remove the air filter from the front grille assembly by pulling the air filter up or down slightly.
3. Wash the filter using lukewarm water below 40 C (104 F).(c)
4. Gently shake the excess water from the filter completely. Replace the filter.
CAUTION: DO NOT operate the air conditioner without a filter because dirt and lint will clog it and
reduce performance.
13
Hardware
Installation Hardware Installation
Learning parts name prior to installation will help you understanding the installation procedure.
Features
1 5 7 6 4 2 3 10 8 9 12 13 11 14
1 5 7 6 3 4 2 15 10 8 9 12 13 11 14
Installation Hardware
Foam
Screw
14
Hardware
Installation Installation Steps
Read completely, then follow step-by step.
ENGLISH
• The appliance shall be installed in accordance with national wiring regulation.
• If a power plug isn't to be used, provide a circuit breaker between power source and the unit, as following
picture.
Level
15
Install the Air Conditioner in the Case
1. Slide the air conditioner into the case. 5. Attach the front grille to the case by inserting the
Reinstall the 2 screws removed earlier on each tabs on the grille into the slots on the front of the
side of the case. case. Push the grille in until it snaps into place.
Screw
Screw
Power Cord
16
Common
Issues Common Problems and Solutions
ENGLISH
Troubleshooting Tips
Save time and money! Review the chart below first and
you may not need to call for service.
Normal Operation
• You may hear a pinging noise caused by water being picked up and thrown against the condenser on rainy
days or when the humidity is high. This design feature helps remove moisture and improve efficiency.
• You may hear the thermostat click when the compressor cycles on and off.
• Water will collect in the base pan during high humidity or on rainy days. The water may overflow and drip from
the outdoor side of the unit.
• The fan may run even when the compressor does not.
Abnormal Operation
Problem Possible Causes What To Do
■ The air conditioner is unplugged. • Make sure the air conditioner plug is pushed
completely into the outlet.
■ The fuse is blown/circuit breaker is • Check the house fuse/circuit breaker box and
Air conditioner tripped. replace the fuse or reset the breaker.
does not start
■ Power failure. • If power failure occurs, push power button to OFF.
When power is restored, wait 3 minutes to restart
the air conditioner to prevent tripping of the
compressor overload.
■ Cooling coils have iced up. • See Air Conditioner Freezing Up below.
■ Ice blocks the air flow and stops • Set the mode control at MED fan or high cool
Air conditioner
the air conditioner from cooling the with the thermostat at 1 or 2 (Left side).
freezing up room. • Set the mode control at HIGH fan or high cool
with the high temperature.
17
Precauciones de
Seguridad Precauciones
Para prevenir tanto lesiones al usuario u otras personas como daños materiales, es preciso seguir
estas instrucciones.
■ El manejo incorrecto debido a la instrucción ignorada puede causar lesioes o daños cuya
gravedad está clasificada en als siguientes indicaciones.
ESPAÑOL
■ El significado de los símbolos utilizados en este manual se indica a continuación.
Asegúrese de no hacerlo.
ADVERTENCIA
■ Instalación
Instale siempre el (los) panel(es) de No coloque el cable eléctrico cerca de un
expansion. calefactor.
• No instalarlo puede causar incendio y/o • Puede causar incendio y descarga eléctrica.
accidente eléctrico.
Gasolin
3
■ Funcionamiento
No modifique la longitud del No comparta la salida con Siempre enchufe las piezas
cable de corriente eléctrica. otros artefactos. eléctricas en una salida
conectada a masa.
• Causará descarga eléctrica o • Causará descarga eléctrica o • Si no hay conexión a masa,
incendio debido a la incendio debido a la se puede producir una
generación de calor. generación de calor. descarga eléctrica. (Vea el
Manual de instalación.)
4
No permita la entrada de Deje la puerta cerrada Ventile antes de hacer
agua. mientras está operando el funcionar el acondicionador
aire acondicionado. de aire cuando sale el gas.
• Puede causar una falla del • Ésta no está diseñado para • Puede causar explosión,
motor o una descarga enfriar la casa entera. incendio, quemaduras.
eléctrica.
ESPAÑOL
PRECAUCION
■ Instalación
Nunca toque las piezas de No bloquee la entrada o la Asegúrese de que la caja
metal de la unidad cuando salida de aire. externa no está dañada por
quite el filtro. los anõs o desgaste.
• Son filosas y pueden causar • Puede causar fallos en la • Si se deja la unidad averiada, hay
lesiones. unidad o accidentes. posibilidad de daños debido a
que esta puede caer. Hay
responsabilidad sobre el daño
debido a falla
del producto.
■ Funcionamiento
Al momento de su instalación, Sostenga el enchufe por el Desconecte el interruptor
evite que se contacte con los cuerpo (no del cable) principal de energía cuando
bordes afilados. cuando lo saque. no lo esté usando.
• Hay riesgo de lesiones • Puede causar descarga • Prevenga un arranque
personales. eléctrica y daño. accidental y la posibilidad de
lesiones.
Bordes
afilados
5
No coloque objetos sobre el Si entra agua a la unidad, gire No limpie la unidad de aire
cable de corriente y cuide el interruptor principal del acondicionado con agua.
que el cable no quede artefacto. Tome contacto con
presionado. el centro de servicio después
de desconectar el enchufe del
tomacorriente.
• Hay peligro de incendio o de • Puede entrar agua en la
descarga eléctrica. unidad y disminuir la
aislación. Puede causar una
descarga eléctrica.
Cuando limpie la unidad, No coloque una mascota o No use la unidad para propósitos
asegúrese primero de que una planta donde quede especiales tales como animals o
estén desconectados la expuesto al flujo directo de vegetales, máquinas de precision
energía y el interruptor. aire. u objetos de arte.
• Como el ventilador gira a alta • Este puede causar lesiones o • Puede causar daño a los
velocidad cuando está funcionando, daños en la mascota o la animales o vegetales y
puede causar lesiones. planta. pérdida de objetos.
Siempre asegure los filtros Use una paño suave para No beba el agua drenada del
al insertarlos. Límpielos limpiar. No use ceras, acondicionador de aire. No
cada dos semanas. solventes o un detergente dirija el flujo de aire sólo a los
fuerte ocupantes de la habitación.
• El funcionamiento sin filtros • La unidad del aire acondicionado • Contiene elementos que
puede dañar la unidad. puede deteriorarse, cambiar de pueden ser nocivos para su
color, o desarrollar manchas en salud. / Esto puede dañar su
la superficie. salud.
x
Wa Thinner
6
Controles
Los controles serán como alguno de los siguientes.
■ THERMOSTAT (TERMOSTATO)
NOTA : Opcional Gire el control del termostato a la configuración deseada. La
posición del control es una configuración normal para las
condiciones habituales. Si es necesario, puede cambiar esta
FAN FAN configuración según sus preferencias de temperatura.
ESPAÑOL
El termostato controla automáticamente las funciones de
enfriamiento o calentamiento, pero el ventilador funciona
continuamente siempre que el acondicionador de aire esté
en marcha. Si la habitación está demasiado caliente, gire el
control del termostato en el sentido de las agujas del reloj; si
está demasiado fría, gírelo en sentido contrario.
■ OPERATION (FUNCIONAMIENTO)
Thermostat Operation OFF (APAGADO) : ( o ) : Apaga el acondicionador de aire.
LOW FAN ( ) : El ventilador funciona a baja
(VENTILADOR BAJO) velocidad sin enfriamiento
(calentamiento).
LOW COOL ( ) : Enfriamiento con un funcionamiento
Heater (ENFRIAMIENTO BAJO) del ventilador a baja velocidad.
Warmer Cooler HIGH COOL ( ) : Enfriamiento con un funcionamiento
Thermostat Operation (ENFRIAMIENTO ALTO) del ventilador a alta velocidad.
LOW HEAT ( ) : Calentamiento con un funcionamiento
(CALENTAMIENTO BAJO) del ventilador a baja velocidad.
■ AUTO SWING (OSCILACIÓN HIGH HEAT ( ) : Calentamiento con un funcionamiento
AUTOMÁTICA) (Opcional) (CALENTAMIENTO ALTO) del ventilador a alta velocidad.
ON ( ) : La oscilación del aire está en funcionamiento
ATENCIÓN: Cuando el acondicionador de aire ha
mientras el mando OPERATION está en
estado operando en enfriamiento y se desconecta
posición COOL o HEAT.
o se ajusta a una posición de ventilador, espere 3
OFF ( ) : Detiene el funcionamiento de la oscilación minutos como mínimo antes de volver a ajustarlo
de aire. para enfriamiento.
9
Instrucciones de
Funcionamiento Operaciones del Mando a Distancia
Los controles tendrán el aspecto de los siguientes esquemas. CONTROL REMOTO
Controles
ATENCIÓN : La unidad de Control Remoto no funcionará adecuadamente si la ventanilla del
sensor del acondicionador de aire recibe luz demasiado fuerte o si hay obstáculos entre la
unidad de Control Remoto y el acondicionador de aire.
1. BOTON DE LA CORRIENTE
Se pone en marcha. Cuando este boton esta apretado, se detiene apretandolo de nuevo.
2. AUTO DEFLECTO (Opcional)
Las aletas se mueven verticalmente por un sistema automatico y se paran cuando presiona el boton otra vez.
3. BOTON DE SELECCION DE LA TEMPER ATURA DE LA HABITACION
Controle la temperatura de la habitacion en una escala entre 16 C y 3 0 C
4. SELECTOR DE LA VELOCIDAD DEL VENTILADOR
Seleccione la velocidad del ventilador en tres pasos [Alto(F3) Bajo(F1) Medio(F2) Alto(F3)...]
5. BOTON DE SELECCION DEL MODO OPERACIONAL
Seleccionar con este boton los modos para Refrescar, Ventilar y Deshumedecer.
6. BOTON ON/OFF TIMER
Ponga la hora de empezar y terminar el funcionamiento. El timer esta preajustado por una hora.(1-12Horas)
~
7. RECEPTOR DE SENAL
AUTO-ARRANQUE
En caso de fallo de la corriente eléctrica, la unidad funcionará como antes cuando vuelve la corriente.
Como Insertar las Baterias Part que Opere el Control Remoto (AAA)
1. Remueva la tapa que se encuentra en la parte trasera • NO USE BATERIAS RECARGABLES
del control remoto en la dirección que indica la flecha. • CUANCO NO UTILICE EL CONTROL POR
2. Inserte 2 pilas esté seguro de colocarlas en la PERIODOS LARGOS
polaridad que especifica en el dibujo grabado en el NO DEJE LAS PILAS
control. EN EL INTERIOR
3. Deslice nuevamente la tapa como indica la flecha DEL CONTROL.
para cerrar el compartimiento de las pilas.
10
Instrucciones de
Funcionamiento Ajuste de la Dirección del Flujo de Aire
Controles adicionales e informacion importante.
Ventilacion
La palanca de ventilación deberá estar en la posición CLOSE (Cerrado) para poder mantener las mejores
condiciones de enfriamiento.
Cuando se necesite aire fresco en la habitación, coloque la palanca de ventilación en la posición OPEN (Abierto).
El amortiguador se abre y se descarga el aire de la habitación. Part B
Part A
ESPAÑOL
CLOSE VENT OPEN
CERRAR VENTILACION ABRIR
11
Como colocar la charola de purga (Para algunos modelos)
El aire acondicionado utiliza un método de purga adecuado en donde el agua condensada (humedad retirada del aire)
se purga al exterior.
En climas demasiado húmedos (y para modelos de ciclo invertido en la modalidad de inversión) el agua condensada
excesiva que se retira del aire puede ocasionar que se recolecte algo de agua. Para eliminar este exceso de agua,
puede instalar una charola de purga como se detalla a continuación.
CABINETE
1. Tome la charola de purga que se localiza en la descarga de aire o en la barrera.
2. Retire el orificio de hule de la charola de la base. (para algunos modelos).
3. Instale la charola de purga en el extermo izquierdo del gabinete con 4 (o 2)
CHAROLA
tornillos.
DE PURGA
4. Conecte la manguera de purga en la descarga localizada en el fondo de la
charola de purga. Puede adquirir la manguera o tubería de purga localmente TORNILLO
MANGUERA
para satisfacer sus necesidades particulares (No se incluye la manguera de
DE PURGA
purga).
Instrucciones de
Funcionamiento Ajuste de la Dirección del Flujo de Aire
APAGUE EL AIRE ACONDICIONADO Y SAQUE EL ENCHUFE DEL TOMA CORRIENTE DE LA PARED.
12
Cuidados y
Mantenimiento Cuidados y Mantenimiento
Limpieza del filtro de aire
El filtro de aire deberá revisarse cuando menos dos veces al mes para verificar si es necesario limpiarlo. Las
partículas atrapadas en el filtro podrían acumularse y bloquear el flujo de aire. Esto reduce la capacidad de
enfriamiento y también ocasiona la acumulación de escarcha en los serpentines de enfriamiento.
1. Abra la rejilla hacia arriba tirando la parte inferior de la rejilla de entrada (a). En otro caso, usted puede abrir
la rejilla de entrada hacia abajo tirando la parte superior de la rejilla de entrada.(b)
ESPAÑOL
2. Retire el filtro de aire del ensamblaje de la parrilla delantera jalando el filtro de aire ligeramente hacia arriba.
3. Lave el filtro de aire usando agua tibia a menos de 40°C (104°F)
4. Sacuda suavemente el exceso de agua del filtro completamente. Vuelva a colocar el filtro.
PRECAUCION: NO OPERE el aire acondicionado sin filtro ya que la suciedad y las pelusas
obstruirán el filtro y se reducirá la eficiencia del funcionamiento.
13
Guía de Instalación
del Equipo Instalación del Equipo
Conocer el nombre de las partes antes de instalar el aire, lo ayudará a entender mejor el proceso de instalación.
Características
1 5 7 6 4 2 3 10 8 9 12 13 11 14
1 5 7 6 3 4 2 15 10 8 9 12 13 11 14
Accesorios de Instalación
Espuma
Tornillo
14
Guía de Instalación
del Equipo Pasos de la Instalación
Lea completamente y siga paso a paso.
• El aparato será instalado de acuerdo con las regulaciones de cableado del país.
• Si no usa un enchufe de alimentación, proporcione un cortacircuitos entre la fuente de energía y la unidad
como la siguiente figura.
ESPAÑOL
de retardo.
15
Instale el Aire acondicionado en la Caja
1. Deslice el aire acondicionado a la caja. 5. Instale la rejilla frontal a la caja insertando las
Reinstale 2 tornillos removidos antes en cada lado lengüetas en la rejilla en las ranuras en el frente de
de la caja. la caja. Empuje la rejilla en la unidad hasta que se
cierren de golpe.
Tornillo
Tornillo
Cable de alimentación
PRECAUCION: El cable de alimentación debe
ser conectado a un circuito independiente.
El cable verde debe ser conectado a tierra.
Cuando usted despegue la
2. Llene la espuma entre el tope de la unidad y la rejilla frontal de la caja, empuje
pared para prevenir que el aire e insectos entren la rejilla a su lado derecho y
en la habitación. tírela hacia usted.
Espuma
2. Si usted desea sacar el filtro por arriba, use la rejilla de entrada reversible sin
cambio. (La rejilla está instalada para tal efecto.)
16
Problemas
Habituales Problemas Habituales y Soluciones
Tips para la resolución de problemas
¡Ahorre tanto el tiempo como el dinero!
Si revisa el siguiente cuadro primero, seguramente usted no necesitará llamar al servicio técnico
frecuentemente.
Operación Normal
• Usted puede oir ruido agudo por el impacto causado por el agua que es recogida y lanzada contra el
condensador cuando llueve o hay humedad muy alta. Esta característica de diseño ayuda a remover la
humedad y mejorar la eficiencia.
• Usted puede oir el sonido de golpe del termostato cuando el compresor pase por el ciclo de encendido y de
ESPAÑOL
apagado.
• El agua se colectará en el plato de base cuando llueva o haya alta humedad. El agua puede rebosar y gotear
de la parte exterior de la unidad.
• El ventilador puede operar aun cuando el compresor no opere.
Operación Anormal
Problema Posibles causas Qué hacer
■ El aire acondicionado está • Asegúrese de que el enchufe del aire acondicionado
desconectado. sea insertado completamente en la toma.
■ El fusible está fundido/ El cortacircuitos • Cheque el fusible/ caja de cortacircuitos y reemplace el
El aire está disparado. fusible o reajuste el cortacircuitos.
acondicionado no ■ Falla de alimentación • Si la falla de alimentación ocurre, posicione el control
pone en marcha. de modo a APAGADO. Cuando la energía sea
restaurada, espere 3 minutos para reiniciar el aire
acondicionado para prevenir la sobrecarga del
compresor.
■ La corriente de aire está obstruida. • Asegúrese de que no exista ni cortinas, ni persianas ni
muebles bloqueando el frente del aire acondicionado.
■ No se ajusto el TERMOSTATO en el • Gire el botón a un número más alto. El ajuste más alto
nivel adecuado (suficientemente alto) proporciona el enfriamiento máximo.
■ Coloque el control de TEMPERATURA • Gire el control de TEMPERATURA a un número más
en un número más alto. bajo.
■ El filtro de aire está sucio. • Limpie el filtro por lo menos cada 2 semanas. Vea la
El aire sección de las instrucciones de operación.
acondicionado no
enfria como se ■ La habitación pudo haber estado • Cuando el aire acondicionado sea encendido, usted
debe. demasiado caliente. debe esperar por un tiempo hasta que la habitación se
ponga fresca.
■ El aire frío está escapando. • Revise si está abierto el control de piso de calefacción
y el aire frío regresa.
• Ajuste el respiradero del aire acondicionado a la
posición cerrada.
■ Se congelaron las laminillas de • Vea “El aire acondicionado congela” abajo.
enfriamiento.
■ El hielo obstruye la corriente de aire e • Ajuste el control de modo en Ventilación Mediana o
El aire impide que el aire acondicionado enfríe Enfriamiento Alto con el termóstato en 1 o 2 (El lado
acondicionado adecuadamente la habitación. izquierdo).
congela. • Ajustar el control de modo en ‘Ventilación alta’ o
‘Erfriamiento alto’ con la temperatura alta.
17
ESPAÑOL
19
Nota
Pagina Web: http://www.lg.com.mx/