Escolar Documentos
Profissional Documentos
Cultura Documentos
LED TV
SERVICE MANUAL
CHASSIS : LW45A
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS ............................................................................................... 2
SAFETY PRECAUTIONS.......................................................................... 3
SERVICING PRECAUTIONS..................................................................... 4
SPECIFICATION........................................................................................ 6
ADJUSTMENT INSTRUCTION................................................................. 9
TROUBLE SHOOTING............................................................................ 13
BLOCK DIAGRAM................................................................................... 24
Copyright © LG Electronics. Inc. All right reserved. -2- LGE Internal Use Only
Only for training and service purposes
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
always perform an AC leakage current check on the exposed Good Earth Ground
such as WATER PIPE,
metallic parts of the cabinet, such as antennas, terminals, etc., to CONDUIT etc.
To Instrument's
be sure the set is safe to operate without damage of electrical exposed
0.15µF
shock. METALLIC PARTS
Copyright © LG Electronics. Inc. All right reserved. -3- LGE Internal Use Only
Only for training and service purposes
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service unit under test.
manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES
SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as
NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or
following servicing precautions and any of the safety precautions on exposure of the assembly.
page 3 of this publication, always follow the safety precautions. 3. Use only a grounded-tip soldering iron to solder or unsolder ES
Remember: Safety First. devices.
4. Use only an anti-static type solder removal device. Some solder
General Servicing Precautions removal devices not classified as "anti-static" can generate
1. Always unplug the receiver AC power cord from the AC power electrical charges sufficient to damage ES devices.
source before; 5. Do not use freon-propelled chemicals. These can generate
a. Removing or reinstalling any component, circuit board electrical charges sufficient to damage ES devices.
module or any other receiver assembly. 6. Do not remove a replacement ES device from its protective
b. Disconnecting or reconnecting any receiver electrical plug or package until immediately before you are ready to install it.
other electrical connection. (Most replacement ES devices are packaged with leads
c. Connecting a test substitute in parallel with an electrolytic electrically shorted together by conductive foam, aluminum foil
capacitor in the receiver. or comparable conductive material).
CAUTION: A wrong part substitution or incorrect polarity 7. Immediately before removing the protective material from the
installation of electrolytic capacitors may result in an leads of a replacement ES device, touch the protective material
explosion hazard. to the chassis or circuit assembly into which the device will be
installed.
2. Test high voltage only by measuring it with an appropriate high CAUTION: Be sure no power is applied to the chassis or circuit,
voltage meter or other voltage measuring device (DVM, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged
Do not test high voltage by "drawing an arc". replacement ES devices. (Otherwise harmless motion such as
3. Do not spray chemicals on or near this receiver or any of its the brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity
4. Unless specified otherwise in this service manual, clean sufficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10% (by volume) Acetone and 90% (by 1. Use a grounded-tip, low-wattage soldering iron and appropriate
volume) isopropyl alcohol (90%-99% strength) tip size and shape that will maintain tip temperature within the
CAUTION: This is a flammable mixture. range or 500 ˚F to 600 ˚F.
Unless specified otherwise in this service manual, lubrication of 2. Use an appropriate gauge of RMA resin-core solder composed
contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks are Do not use freon-propelled spray-on cleaners.
correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 ˚F to 600 ˚F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 ˚F to 600 ˚F)
Some semiconductor (solid-state) devices can be damaged easily b. First, hold the soldering iron tip and solder the strand against
by static electricity. Such components commonly are called the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors and component lead and the printed circuit foil, and hold it there
semiconductor "chip" components. The following techniques only until the solder flows onto and around both the
should be used to help reduce the incidence of component component lead and the foil.
damage caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. splashed solder with a small wire-bristle brush.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the
Copyright © LG Electronics. Inc. All right reserved. -4- LGE Internal Use Only
Only for training and service purposes
IC Remove/Replacement CAUTION: Maintain original spacing between the replaced
Some chassis circuit boards have slotted holes (oblong) through component and adjacent components and the circuit board to
which the IC leads are inserted and then bent flat against the prevent excessive component temperatures.
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with Circuit Board Foil Repair
boards using the familiar round hole, use the standard technique Excessive heat applied to the copper foil of any printed circuit
as outlined in paragraphs 5 and 6 above. board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
Removal following guidelines and procedures should be followed whenever
1. Desolder and straighten each IC lead in one operation by gently this condition is encountered.
prying up on the lead with the soldering iron tip as the solder
melts. At IC Connections
2. Draw away the melted solder with an anti-static suction-type To repair a defective copper pattern at IC connections use the
solder removal device (or with solder braid) before removing the following procedure to install a jumper wire on the copper pattern
IC. side of the circuit board. (Use this technique only on IC
Replacement connections).
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and 1. Carefully remove the damaged copper pattern with a sharp
solder it. knife. (Remove only as much copper as absolutely necessary).
3. Clean the soldered areas with a small wire-bristle brush. 2. carefully scratch away the solder resist and acrylic coating (if
(It is not necessary to reapply acrylic coating to the areas). used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
"Small-Signal" Discrete Transistor carefully crimp it around the IC pin. Solder the IC connection.
Removal/Replacement 4. Route the jumper wire along the path of the out-away copper
1. Remove the defective transistor by clipping its leads as close as pattern and let it overlap the previously scraped end of the good
possible to the component body. copper pattern. Solder the overlapped area and clip off any
2. Bend into a "U" shape the end of each of three leads remaining excess jumper wire.
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads. At Other Connections
4. Connect the replacement transistor leads to the corresponding Use the following technique to repair the defective copper pattern
leads extending from the circuit board and crimp the "U" with at connections other than IC Pins. This technique involves the
long nose pliers to insure metal to metal contact then solder installation of a jumper wire on the component side of the circuit
each connection. board.
Power Output, Transistor Device 1. Remove the defective copper pattern with a sharp knife.
Removal/Replacement Remove at least 1/4 inch of copper, to ensure that a hazardous
1. Heat and remove all solder from around the transistor leads. condition will not exist if the jumper wire opens.
2. Remove the heat sink mounting screw (if so equipped). 2. Trace along the copper pattern from both sides of the pattern
3. Carefully remove the transistor from the heat sink of the circuit break and locate the nearest component that is directly
board. connected to the affected copper pattern.
4. Insert new transistor in the circuit board. 3. Connect insulated 20-gauge jumper wire from the lead of the
5. Solder each transistor lead, and clip off excess lead. nearest component on one side of the pattern break to the lead
6. Replace heat sink. of the nearest component on the other side.
Carefully crimp and solder the connections.
Diode Removal/Replacement CAUTION: Be sure the insulated jumper wire is dressed so the
1. Remove defective diode by clipping its leads as close as it does not touch components or sharp edges.
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Copyright © LG Electronics. Inc. All right reserved. -5- LGE Internal Use Only
Only for training and service purposes
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application Range
This spec sheet is applied all of the TV used LW45A chassis.
2. Specification
Each part is tested as below without special appointment
3.Test method
1) Performance : LGE TV test method followed
2) Demanded other specification
- Safety : CE,IEC specification
- EMC : CE,IEC specification
4. General specification
4.1. Operating/Storage environment
Temp : 10 °C ~ 35 °C
1 Operating Environment
Humidity : 20 % ~ 80 %
Temp : -10 °C ~ 60 °C non condensing
2 Storage Environment
Humidity : 5 % ~ 90 % non condensing
4.2. RGB-PC
No. Item Specification Remarks
1 Supported Sync. Type Separate Sync.(RGB)
Horizontal 30 ~ 69 kHz 22MT47A, 24MT47A,28MT47A,29MT47A
2 Operating Frequency Analog
Vertical 56 ~ 61 Hz 22MT48A,22MT48N,24MT48N
Max 1920×1080 @ 60 Hz
21MT47A,22MT47A, 22MT48A,22MT48N
Recommend 1920×1080 @ 60 Hz
Max 1366×768 @ 60 Hz
3 Resolution Analog 24MT47A,24MT48N,28MT47A,29MT47A
Recommend 1366×768 @ 60 Hz
Max. 1600×900 @ 60Hz 1600×900 @ 60Hz
Recommend 1600×900 @ 60Hz 1600×900 @ 60Hz
Copyright © LG Electronics. Inc. All right reserved. -6- LGE Internal Use Only
Only for training and service purposes
4.3. TV
No. Item Specification Remarks
1 Market NON EU
PAL/SECAM B/G/D/K,
2 Broadcasting system
PAL I, NTSC-M
PAL(BG,I) NTSC(M) China(DK)
3 Available Channel 01~C69 2~78 C1~C69 Except for the 47M.
S1~S47 1~71 S1~S47
4 Receiving system Upper Heterodyne
Rear (1EA) – MT47A/MT48A
5 Video Input PAL, SECAM, NTSC Rear(2EA) – MT48N
Except for the 47M.
6 RGB Input RGB-PC(Analog (D-SUB 15Pin) Rear (1EA)
7 USB Input MP3, JPEG, Movie Rear (1EA) or Side(1EA)
8 AV Audio Output RF/AV/HDMI Audio Output Rear (1EA)
9 HDMI Input HDMI-DTV Rear (1EA)
L/R Input(1EA) – MT47A/MT48A
AV
L/R Input(2EA) – MT48N(AV1/AV2)
10 Audio Input (1EA) AV&RGB-PC
L/R Input(1EA) – MT47A/MT48A
RGB-PC
L/R Input(1EA) – MT48N(Only AV1)
5. RGB-PC Input ( PC )
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark
1 640*480 31.469 59.94 25.175
2 800*600 37.879 60.317 40.0
3 1024*768 48.363 60.0 65.0
4 1152*864 54.34 60.05 80
5 1280*1024 63.981 60.02 108.0
6 1600*900 55.54 60 97.75
7 1680*1050 64.674 59.883 119.0
8 1680*1050 65.290 59.954 146.25
Max Resolution
9 1920*1080 67.5 60 148.5 Recommend
Resolution
* Monitor Range Limits
Min Vertical Freq - 56 Hz/ Max Vertical Freq - 61 Hz
Min Horiz. Freq - 30 kHz/ Max Horiz. Freq - 69 kHz
Pixel Clock - 150 MHz
Copyright © LG Electronics. Inc. All right reserved. -7- LGE Internal Use Only
Only for training and service purposes
6. HDMI Input (DTV)
No Resolution H-freq(kHz) V-freq.(kHz) Pixel clock(MHz) Proposed Remarks
1 720*480 15.73 59.94 13.500 SDTV, DVD 480I(525I)
2 720*480 15.75 60.00 13.514 SDTV, DVD 480I(525I) Spec. out but display.
3 720*576 15.625 50.00 13.500 SDTV, DVD 576I(625I) 50Hz
4 720*480 31.469 59.94 27 SDTV 480P
5 720*480 31.5 60.00 27.027 SDTV 480P
6 720*576 31.25 50.00 27 SDTV 576P
7 1280*720 44.96 59.94 74.176 HDTV 720P
8 1280*720 45 60.00 74.25 HDTV 720P
9 1280*720 37.5 50.00 74.25 HDTV 720P
10 1920*1080 28.125 50.00 74.25 HDTV 1080I
11 1920*1080 33.72 59.94 74.176 HDTV 1080I
12 1920*1080 33.75 60.00 74.25 HDTV 1080I
13 1920*1080 56.25 50.00 148.5 HDTV 1080P
14 1920*1080 67.432 59.94 148.350 HDTV 1080P
15 1920*1080 67.5 60.00 148.5 HDTV 1080P
16 1920*1080 27 24.00 74.25 HDTV 1080P
17 1920*1080 33.75 30.00 74.25 HDTV 1080P
18 1920*1080 26.97 23.97 74.25 HDTV 1080P
Max Resolution
19 1920*1080 33.716 29.976 74.25 HDTV 1080P Recommend Resolu-
tion
Copyright © LG Electronics. Inc. All right reserved. -8- LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTION
1. Application Range
This spec. sheet applies to LW45A Chassis applied TV all 3.2.4. EDID DATA
models manufactured in TV factory - 21MT47A,22MT47A, 22MT48A ,22MT48N(RGB-PC)
** RGB-PC : 128Bytes
0 1 2 3 4 5 6 7 8 9 A B C D E F
2. Specification 0 00 FF FF FF FF FF FF 00 1E 6D C4 59 01 01 01 01
30 95 00 90 40 A9 C0 02 3A 80 18 71 38 2D 40 58 2C
[Caution] 40 45 00 DC 0C 11 00 00 1E 21 39 90 30 62 1A 27 40
90 1F 07 16 01 26 11 07 50 09 7F 07 65 03 0C 00 10
A0 00 02 3A 80 18 71 38 2D 40 58 2C 45 00 DC 0C 11
3. ADC calibration B0 00 00 1A 01 1D 80 18 71 1C 16 20 58 2C 25 00 DC
F0 40 10 2C 45 20 DC 0C 11 00 00 1E 00 00 00 00 1D
NO Item CMD CMD Data 0
1 2
Adjust Sequence
▪aa 00 00 [Enter Adjust Mode]
▪xb 00 60 [RGB Input (1024*768)]
▪ad 00 10 [Adjust 1024*768 RGB]
▪aa 00 90 End Adjust mode
3.2.2. Equipment
- Since EDID data is embedded, EDID download JIG, HDMI
cable and D-sub cable are not need.
Copyright © LG Electronics. Inc. All right reserved. -9- LGE Internal Use Only
Only for training and service purposes
4. Final Assembly Adjustment 4.1.4. Adjustment Command (Protocol)
(1) RS-232C Command used during auto-adj.
4.1. White Balance Adjustment RS-232C COMMAND
4.1.1. Overview CMD ID DATA
Explantion
▪ W/B adj. Objective & How-it-works wb 00 00 Begin White Balance adjustment
(1) Objective: To reduce each Panel's W/B deviation End White Balance adjustment
(2) How-it-works : When R/G/B gain in the OSD is at 192, it wb 00 ff
(internal pattern disappears )
means the panel is at its Full Dynamic Range. In order to
prevent saturation of Full Dynamic range and data, one of (2) Adjustment Map
R/G/B is fixed at 192, and the other two is lowered to find Command Data Range Default
Adj. item
the desired value. (lower caseASCII) (Hex.) (Decimal)
(3) Adjustment condition : normal temperature CMD1 CMD2 MIN MAX
1) Surrounding Temperature : 25 °C ± 5 °C R Gain j g 00 C0
2) Warm-up time: About 5 Min G Gain j h 00 C0
3) Surrounding Humidity : 20 % ~ 80 % B Gain j i 00 C0
4) Before White balance adjustment, Keep power on Cool
R Cut
status, don’t power off G Cut
* Adj. condition and cautionary items B Cut
(1) Lighting condition in surrounding area surrounding lighting R Gain j a 00 C0
should be lower 10 lux. Try to isolate adj. area into dark
G Gain j b 00 C0
surrounding.
B Gain j c 00 C0
(2) Probe location: Color Analyzer (CA-210) probe should Medium
R Cut
be within 10cm and perpendicular of the module surface
G Cut
(80°~ 100°)
(3) Aging time B Cut
1) After Aging Start, Keep the Power ON status during R Gain j d 00 C0
5 Minutes. G Gain j e 00 C0
2) In case of LCD, Back-light on should be checked Warm B Gain j f 00 C0
using no signal or Full-white pattern. R Cut
G Cut
4.1.2. Equipment
(1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12 / LED:
CH14)
(2) Adj. Computer (During auto adj., RS-232C protocol is
needed)
(3) Adjust Remocon
(4) Video Signal Generator MSPG-925F 720p/204-
Gray(Model: 217, Pattern: 49)
* Color Analyzer Matrix should be calibrated using CS-1000
Probe RS -232C
DFT JIG
Co m p ut er
RGB Cable RS -232C RS -232C
Copyright © LG Electronics. Inc. All right reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
4.1.5. Adj. method 5. Tool Option selection
*Auto WB calibration ▪ Method : Press "ADJ" key on the Adjustment remote control,
1) Set TV in ADJ mode using P-ONLY key (or POWER ON then select Tool option.
key)
2) Place optical probe on the center of the display
- It need to check probe condition of zero calibration
before adjustment. 6. Ship-out mode check(In-stop)
3) Connect RS-232C Cable ▪ After final inspection, press "IN-STOP" key of the Adjustment
4) Select mode in ADJ Program and begin a adjustment. remote control and check that the unit goes to Stand-by
5) When WB adjustment is completed with OK message, mode.
check adjustment status of pre-set mode (Cool, Medium,
Warm)
6) Remove probe and RS-232C cable.
▪ W/B Adj. must begin as start command “wb 00 00” , and fin-
7. GND and Hi-pot
ish as end command “wb 00 ff”, and Adj. offset if need. 7.1. GND & HI-POT auto-check preparation
1) Check the POWER CABLE and SIGNAL CABE insertion
* LED White balance table condition
If Model is Polaris Model, G-gain fix is applied.
(1) Cool Mode 7.2. GND & HI-POT auto-check
1) Purpose : Especially G-gain fix adjust leads to the lu- 1) Pallet moves in the station. (POWER CORD / AV CORD is
minance enhancement. Adjust the color temperature tightly inserted)
to reduce the deviation of the module color tempera- 2) Connect the AV JACK Tester.
ture. 3) Controller (GWS103-4) on.
2) Principle : To adjust the white balance without the 4) GND Test (Auto)
saturation, Adjust the G gain more than 172 ( If R - If Test is failed, Buzzer operates.
gain or G gain is more than 255 , G gain can adjust - If Test is passed, execute next process (Hi-pot test).
less than 172 ) and change the others ( R/B Gain ). (Remove A/V CORD from A/V JACK BOX)
3) Adjustment mode : mode – Cool 5) HI-POT test (Auto)
(2) Medium / Warm Mode - If Test is failed, Buzzer operates.
1) Purpose : Adjust the color temperature to reduce the - If Test is passed, GOOD Lamp on and move to next
deviation of the module color temperature. process automatically.
2) Principle : To adjust the white balance without the
saturation, Fix the one of R/G/B gain to 192 (default
data) and decrease the others. 7.3. Checkpoint
3)Adjustment mode : Two modes – Medium / Warm 1) Test voltage
- GND: 1.5KV/min at 100mA
4.1.6 Reference - SIGNAL: 3KV/min at 100mA
(White Balance Adj. coordinate and color temperature) 2) TEST time: 1 second
1) Luminance: 204 Gray, 80IRE 3) TEST POINT
2) Standard color coordinate and temperature using CS-1000 - GND Test = POWER CORD GND and SIGNAL CA-
(over 26 inch) BLE GND.
- Hi-pot Test = POWER CORD GND and LIVE & NEU-
TRAL.
4.1.7. Reference 4) LEAKAGE CURRENT: At 0.5mArms
(White Balance Adj. coordinate and color temperature)
* The spec of color temperature and coordinate.
Color Cool 9,300K °K x= 0.291 (±0.04) <Test Signal>
Temperature y= 0.294 (±0.04) - Inner pattern
for W/B adjust
8. Audio
Medium 8,000K °K x= 0.300 (±0.04) - External white Measurement condition:
y= 0.310 (±0.04) pattern 1) RF input: Mono, 1 KHz sine wave signal, 100 % Modulation
Warm 6,500K °K x= 0.318 (±0.04) (80IRE, 204gray) 2) CVBS, Component: 1 KHz sine wave signal 0.5 Vrms
y= 0.334 (±0.04) 3) RGB PC: 1 KHz sine wave signal 0.7 Vrms
Luminance Cool Min : 80 Typ : 110 <Test Signal> No. Item Min Typ Max Unit Remark
(cd/m²) Inner pattern Audio practical
Medium Min : 80 Typ : 110 (204gray,80IRE) W (1) Measurement condition
max Output, L/R
1 4.5 5.0 6.0 Vrms - EQ/AVL/Clear Voice: Off
Warm Min : 70 Typ : 110 (Distortion=10%
(2) Speaker(8Ω Impedance)
max Output)
Copyright © LG Electronics. Inc. All right reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
9. USB S/W Download(Service only) 10. Optional adjustments
1) Put the USB Stick to the USB socket. 10.1. Manual ADC Calibration
2) Automatically detecting update file in USB Stick. ■ Enter ‘EZ ADJUST’ mode by pressing ‘ADJ’ key.
- If your downloaded program version in USB Stick is Low, it ■ Enter Internal ADC calibration mode by pressing ‘►’ or ‘OK’
didn't work. But your downloaded version is High, USB data key at ‘ADC Calibration’
is automatically detecting.(Download Version High & Power lGhkq|z{G
10.2.3. Adjustment
(1) Set TV in Adj. mode using POWER ON
(2) Zero Calibrate the probe of Color Analyzer, then place it on
the center of LCD module within 10cm of the surface.
(3) Press ADJ key → EZ adjust using adj. R/C → White Bal-
ance then press the cursor to the right (KEY►). When
KEY(►) is pressed 216 Gray internal pattern will be
displayed.
(4) One of R Gain / G Gain / B Gain should be fixed at 192,
and the rest will be lowered to meet the desired value.
(5) Adj. is performed in COOL, MEDIUM, WARM 3 modes of
color temperature.
Copyright © LG Electronics. Inc. All right reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
TROUBLE SHOOTING
1. NO POWER-Main PCBA
NO POWER
YES
YES
3
NO check the Lines of IC711,IC704
Is 1.8V at C745? If there is any problem at Line,
is 1.25V at C742? Change IC704,IC706.
YES
4
Check Line short or open between
NO
Check waveform of X501 IC501 and X501,
Change IC501 or change X501
YES
5
is 3.3V at 1pin of P120?
NO Change control
when push power key,
Or check Line short or open of P120
Is 0v at 2pin of P120?
YES
6
is there any waver at 11pin of P120, NO change IR board
when use remote controller? Or check Line short or open of P120
Insert F/W 4
X501
Copyright © LG Electronics. Inc. All right reserved. - 13 - LGE Internal Use Only
Only for training and service purposes
2. No raster (Power LED blue, black screen)
NO RASTER
(Screen is not displayed)
YES
Check Line short or open between
2 NO IC711/IC704 and IC501,
Is 1.25V at 4pin of IC704?
If there is any problem at Line,
Is 1.8V at 2pin of IC711?
Change IC711/IC704 or change IC501
YES
It is not over 3V at 1pin of IC601.
3 NO Change Q601.
is 3V at 1pin of IC601? Or check Line short or open between
R603 and 95pin of IC501.
Change IC 501.
YES
Copyright © LG Electronics. Inc. All right reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
3. Abnormal/No screen (All input)-Main PCBA
Abnormal/No screen
(all input)
YES
If is not under 1.5V at R722,
change Q721 or check open and short
2 NO of Line among Q720 and Q721.
Is 12V at 1pin of P101? If is under 11V at L110,
Check open and short
Of line between L110 and P101.
YES
YES
Change module
WAVEFORMS
Copyright © LG Electronics. Inc. All right reserved. - 15 - LGE Internal Use Only
Only for training and service purposes
4. Abnormal screen (TV)-Main PCBA
YES
If 1.7V is not at plus pin of TU401, check
2 NO It is over 3V at 2pin of IC711,
Is 1.8V at 7pin of TU401? if it is not, Check Line between TU401
and IC711 is open or short.
Another is change IC711 or TU401
WAVEFORMS
3 4
Copyright © LG Electronics. Inc. All right reserved. - 16 - LGE Internal Use Only
Only for training and service purposes
5. Abnormal screen (AV)-Main PCBA
Abnormal screen (AV)
1 NO
Put into AV cable completely? Insult AV cable tight
YES
YES
YES
Change IC501
WAVEFORMS
3
R505 (CVBS)
Copyright © LG Electronics. Inc. All right reserved. - 17 - LGE Internal Use Only
Only for training and service purposes
6. Abnormal screen (RGB PC)-Main PCBA
YES
YES
YES
Change IC501
WAVEFORMS
3
Copyright © LG Electronics. Inc. All right reserved. - 18 - LGE Internal Use Only
Only for training and service purposes
7. Abnormal screen (HDMI)-Main PCBA
YES
YES
3 Can read EDID and Check Line between JK203 and IC501
HDCP key though is open or short, Another is
16,15pin of JK203 Change HDMI cable
YES
YES
YES
Check Line between JK203 and IC501
6 Is waveform at 1,3,4,6,7,9pin NO
is open or short, Another is
Of JK203? Change HDMI cable
YES
Change IC501
Copyright © LG Electronics. Inc. All right reserved. - 19 - LGE Internal Use Only
Only for training and service purposes
8. No sound (all source )-Main PCBA
NO sound (All source)
1
NO
Does wire connect P301 with speaker? Connect wire between P301 and speaker.
YES
If 8V is not plus at L703, check
2 of JK700 is open.
Is 19.4V at 19,20,31,32pin NO
If is not Check Line between L703
of IC301 ? and IC301 is open or short.
.Another is change IC301
YES
If 3V is not plus 30pin of IC301,
3 check It is over 3V at L301
NO
Is 3.3V at 40pin of IC301? if it is not, Check Line between L301
and IC301 is open or short.
Another is change IC701,IC301
YES
4
Check Line between IC301 and IC501
Is I2C waveform at NO
is open or short, Another is change
10,11pin of IC301?
IC301 or IC501.
YES
5 Check Line between IC301 and IC501
Is I2S waveform at NO
is open or short, Another is change
R301,R302,R303,R304? IC301 or IC501.
4 5
5 6
Copyright © LG Electronics. Inc. All right reserved. - 20 - LGE Internal Use Only
Only for training and service purposes
9. Abnormal sound (TV)-Main PCBA
YES
WAVEFORMS
3 4
Copyright © LG Electronics. Inc. All right reserved. - 21 - LGE Internal Use Only
Only for training and service purposes
10. Abnormal sound (AV)-Main PCBA
Abnormal sound (AV)
1 NO
Put into AV cable completely? Insult AV cable tight
YES
YES
Change IC501
WAVEFORMS
C520,C521(audio in)
Copyright © LG Electronics. Inc. All right reserved. - 22 - LGE Internal Use Only
Only for training and service purposes
11. Abnormal sound (HDMI)-Main PCBA
YES
YES
3 Can read EDID and Check Line between JK203 and IC501
HDCP key though is open or short, Another is
16,15pin of JK203 Change HDMI cable
YES
YES
YES
Check Line between JK203 and IC501
6 Is waveform at 1,3,4,6,7,9pin NO
is open or short, Another is
Of JK203? Change HDMI cable
YES
Change IC501
Copyright © LG Electronics. Inc. All right reserved. - 23 - LGE Internal Use Only
Only for training and service purposes
BLOCK DIAGRAM
Copyright © LG Electronics. Inc. All right reserved. - 24 - LGE Internal Use Only
Only for training and service purposes
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts
are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as recommended
in this manual to prevent Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
910
400
900
535
401
LV1
820
120
A2
540
810
800
200
510
300
305
Copyright © LG Electronics. Inc. All right reserved. - 25 - LGE Internal Use Only
Only for training and service purposes
EAX65643103
44A/45A/450A
[RD1]E-LUG
6B IR & LED C126
4.7uF 1
R120 R121 10V
R122 JP120
3.3K 3.3K
100
2
5B [RD1]C-SPRING KEY1
C121 JP121
ROUT R123
100
0.1uF
16V
3
44A
KEY2 P121
D121
20V
D120
C120 JP122 SMAW200-05
20V
4B [RD1]CONTACT 0.1uF
16V 4
JP123
1
EEP_SCL 5
6G [RD3]E-LUG JP127
5
9
C JP128
R126
10K B Q120 10
5G [RD3]C-SPRING LED_B MMBT3904(NXP)
JP129
RIN READY
R127
E
11
10K
100pF 50V
100pF 50V
D126 20V
20V
[RD3]CONTACT
READY
READY
C122
C123
4G 12
D127
13
5F [WH2]C-SPRING
LIN
JP108
[RD2]C-SPRING
COMPONENT_KDZ5.6V
COMPONENT_KDZ5.6V
5E
COMMON_R
ZD105-*1
R130
ZD106-*1
COMPONENT_UDZS5.6B 100
5.6V
COMPONENT
5.6V
ZD105 R145 IR
SD05
[RD2]E-LUG-S
D123
75 C124
20V
JP130
7E ZD106
SD05 +3.5V_ST 1000pF
50V
COMPONENT_UDZS5.6B
JP131
JP107
5D [BL]C-SPRING
COMPONENT_KDZ5.6V
COMPONENT_KDZ5.6V
COMMON_B
ZD103-*1
COMPONENT_UDZS5.6B
ZD104-*1
4.7uF
5.6V
5C [GN/YL]C-SPRING
6C [GN/YL]E-LUG
MODULE_HD MODULE_FHD MODULE_HD_18.5
P101
10031HR-30
LVDS P102
10031HR-30
P103
10031HR-30
12.12.19. ESD(Add zenerDiode) PANEL_VCC PANEL_VCC
JP111 JP112
1 1 1
2 2 2
3 3 3
JK101 Composite Jack INTERLACE MODE
4 4 22inch FHD IPS 4
PPJ234-03 AV_IN/OUT Change Option Name.(22LN4300 -> 22LB)
5 5 5
6E [YL]E-LUG R100 -. TN FHD : PWM OUT(If not use : NC)
-. IPS FHD : Interlace(If not use : GND)
6 6 0 6
RXA3+
12.12.18 : ESD(Add to zener diode) 7 7 7
RXA3-
RXA3+
5E [YL]O-SPRING 8 8
RXA3+ 8
COMMON_VIN 9 9
RXA3-
9
ZD101-*1
ZD102-*2
READY
KDZ5.6V
RXACK+
5.6V
5.6V
C103 1K MNT_LOUT 25 25
RXB2+
RXB2+ 25
RXA0+
D104 1000pF RXB2-
C B 26 26 26
[WH1]E-LUG-S
20V 50V
E MUTE_AOUT RXB1+
RXB2- RXA0-
7B R112
3.9K
POP NOISE 27 PANEL_VCC 27
RXB1+ 27
Q101 RXB1-
28 28 28
MMBT3904(NXP)
RXB1-
LOUT To improve EMS S2a issue. 29
JP110
29
RXB0+
29
4A [RD1]CONTACT 2013.11.27 by BJ.KIM RXB0-
RXB0+
30 30 30
READY RXB0-
C106 C112
To improve EMS S2a issue. 10uF 31 10uF 31 31
C105 1K MNT_ROUT
D105 1000pF C B
[RD1]E-LUG
20V 50V
E MUTE_AOUT
6A R113
3.9K POP NOISE
Q103
MMBT3904(NXP)
ROUT
Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
EAX65643103
44A/45A/450A
91 RGB
EAH39491601 -> EAF61771401
91 RGB
10K
91 RGB
B Q230
HDMI1_HPD 2013.11.27 by BJ.KIM
R202
R203
MMBT3904(NXP)
R201
HDMI2 To improve HDMI Detect speed.(OPT(HDMI2)->Apply)
E 2013.11.27 by BJ.KIM
D201
D202
D203
RGB
RGB
RGB
+3.5V_ST
+5V_USB
6 RED_GND GND_R
OPT
10K
R235
HDMI1_DET
GND_2
HDMI2
SHIELD
D231
1 11
RGB
R214
READY
RED 20
D209
0
R219
15
COMMON_R 19 HPD
COMPONENT HDMI2 HDMI2
GREEN_GND JP220
R214-*1
0 GND_G
18 +5V_POWER R232 R233
7 2.7K 2.7K
READY
R204
DDC_DATA
D248
33 17 DDC/CEC_GND
2 12 RGB JP204
GREEN JP221
R215
15
16 SDA HDMI1_SDA
BLUE_GND JP222
COMPONENT
R215-*1 GND_B
2013.05.30 CJ.LIM DSUB_G 15 SCL
JP205
HDMI1_SCL
8 0 14 NC
HDMI2
RGB D233
D232
ESD_HDMI2_IP4283 D234
R205 IP4283CZ10-TBA EAH39491601 -> EAF61771401
H_SYNC 33 13 CEC HDMI2 2013.11.27 by BJ.KIM
3 13 RGB
R216
DSUB_HSYNC
12 CLK- TMDS_CH1- NC_4
BLUE JP223 15
1 10 HDMI2
COMMON_B 11 CLK_SHIELD TMDS_CH1+ NC_3
R253
2 9 5.6
NC JP224
CLK+
HDMI2
HDMI1_CK-
9 COMPONENT
R216-*1 RGB 10 GND_1
3 8
GND_2 R254
R206 5.6
V_SYNC 0
33 9
DATA0-
TMDS_CH2- NC_2
HDMI2
HDMI1_CK+
4 14 DSUB_VSYNC DATA0_SHIELD 4 7 R255
5.6
GND_1 JP225
8
TMDS_CH2+ NC_1
HDMI2
HDMI1_D0-
DATA0+ 5 6 R256
+3.3V_ST 7 5.6
SYNC_GND DATA1- HDMI1_D0+
10 RGB
6
D235 ESD_HDMI2_IP4283
JP226 R207
DDC_CLOCK 33 R208
10K
5
DATA1_SHIELD IP4283CZ10-TBA HDMI2
5 15 JP227 DATA1+
R257
5.6
DDC_GND 4 TMDS_CH1-
1 10
NC_4 HDMI2
HDMI1_D1-
R258
DSUB_DET 3 DATA2- TMDS_CH1+ NC_3 5.6
HDMI2
2 9
HDMI1_D1+
RGB C203 68pF
DATA2_SHIELD
RGB C204 68pF
RGB R212 22K
D206
D207
D208
4 7 5.6
C202
SHILED 68pF TMDS_CH2+ NC_1
HDMI1_D2+
50V 5 6
JK203
RGB
RGB
RGB
HDMI2
1.RED
2.GRN
3.BLU EAH39491601 -> EAF61771401
2013.11.27 by BJ.KIM
4.NC +5V_USB
5.ST-DET
7.GNC R210
8.B_GND 4.7K
9.G_GND DSUB_SCL
10.R_GND
11.GND DSUB_SDA
12.SDA R209 READY
4.7K READY
13.HSYNC +5V_USB_OUT C205 C206
14.VSYNC
15.SCL 2012
NON_USB_OCP
R217
+5V_USB
18pF
50V
18pF
50V
HDMI1 HDMI1
R242
1K
0 HDMI1
C
R241 HDMI1
10K B Q240
IC200
AP2191DSG
HDMI2_HPD MMBT3904(NXP) +3.5V_ST EAH39491601 -> EAF61771401
2013.11.27 by BJ.KIM
NC GND E
8 1 To improve HDMI Detect speed.(OPT(HDMI1)->Apply)
USB_OCP 2013.11.27 by BJ.KIM
10K
R816
OPT
OUT_2 IN_1
7 2
OUT_1 IN_2
6 3
C200 HDMI2_DET
FLG EN C207
0.1uF 5 4
USB_CTL
R220
READY
D246
16V 0.1uF +5V_USB
R200 16V SHIELD
0
READY
10K
R218
4.7K
HDMI1
20 D241
R211 19 HPD
47 HDMI1 HDMI1
18 +5V_POWER R243 R244
2.7K 2.7K
READY
D247
17 DDC/CEC_GND
JP206
16 SDA HDMI2_SDA
15
SCL
ESD_HDMI1_IP4283 HDMI1 HDMI1
HDMI2_SCL
14 NC JP207 D244
IP4283CZ10-TBA D242 D243
13 CEC HDMI1
TMDS_CH1- NC_4 R245
12 CLK-
1 10
R248
HDMI2_D0-
JK205 REAR_USB DATA0_SHIELD 5.6
SIDE_USB C221 C222 8 TMDS_CH2+ NC_1
JP208 JP250
DATA1+ R249
4 TMDS_CH1- NC_4 5.6
HDMI1
2
HDMI2_D1-
2
SIDE_USB_DN REAR_USB_DN 1 10
JP209 JP251 3 DATA2- TMDS_CH1+ NC_3
R250
5.6
HDMI1
3 DATA2_SHIELD 2 9
HDMI2_D1+
3
TMDS_CH2- NC_2
4 7 5.6
HDMI2_D2+
5
5 TMDS_CH2+ NC_1
5 6
JK204
HDMI1
Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
EAX65643103
44A/45A/450A
SW_RESET R310 100
C320
1000pF
50V
+19V
50V
I2S_MCLK R304 100
4.7K
22000pF
C319
+3.3V_M TAIYO YUDEN
R311
READY L303-*1
C318 C317 C348 10.0uH
C321 0.1uF 10uF 10uF
10uF 25V 25V 25V
[EP]GND
10V
ABCO
VDD_IO
GND_IO
PGND1A
PVDD1A
PVDD1B
R313 R314 SPK_L+
L303
CLK_I
RESET
BST1A
OUT1A
12 12
10uH
To improve CST issue.(X5R -> X7R) R322
C330
EAE31360401->EAE52158501 0.1uF
2013.11.27 C325 50V 4.7K
AD
390pF
50V
C329
C326 ABCO 0.47uF
50V
SPEAKER_L
390pF
50V C331 R323
L304
40
39
38
37
36
35
34
33
32
31
0.1uF
10uH 50V 4.7K
R315 R316 SPK_L-
NC_1 1 30 OUT1B 12 12
TAIYO YUDEN
C314 SPK_L-
I2S_SDO
R301 100 SDATA 7 24 VDR2 1uF SPK_L- JP302
3 3
POWER_DET
C341
0.1uF
25V Q341
MMBT3904(NXP)
C
E
B R342 1K 1 OUT1 OUT4 14
C342
0.0068uF R343 10K
MNT_LOUT 50V
R341
4.7K C343 33pF 50V 2 INPUT1- INPUT4- 13
R344
6.8K
MNT_L_AMP
R345 5.6K 3 INPUT1+ INPUT4+ 12
+18V
4 VCC GND 11
C344
0.1uF
25V
MNT_R_AMP
R346 5.6K 5 INPUT2+ INPUT3+ 10
+18V C345 33pF 50V
Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
TBD
44A/45A/450A
TU401-*1
TDJH-G301D
+3.3V
1 Y15_PAL_TUNER
NC_1
2
IF_AGC
3
SCL_RF
4
SDA_RF
5
IF[P]
6
IF[N]
7
SIF
8
NTSC
IF 9
CVBS
A1 B1
A1 B1
TU402 47
TDSS-H701F SHIELD
NC_1 MULTI_TUNER
1 +3.3V_TU
TU401 +3.3V_M
NC_2 TUNER
2 TDJH-G101D Near the pin L401
BLM18PG121SN1D
TUNER TUNER
SCL C405 C404
3 0.1uF
16V
22uF
6.3V
+3.3V_TU
B1[+3.3V]
SDA 1 READY
R404
4 NC_1
To set multi option for NTSC
2013.11.27 by BJ.KIM READY
R403
100K
2 100 +3.3V_TU
TUNER_RESET
+B1[3.3V] NTSC
R412-*1 READY
5 IF_AGC R412 1K C401
0.1uF
3 100
IF_AGC 16V
TUNER
TUNER
C410 should be guarded by ground
NC_3 SCL
0.1uF
16V
PAL
TUNER
R407
1K
R408
1K
6 4
TUNER TUNER
C402
R415 33
C406 TUNER_SCL
20pF 20pF
NC_4 SDA 50V
TUNER
TUNER
R416 33
50V
READY
7 5 C403 C407 TUNER_SDA
NTSC 20pF 20pF
PAL
IF[P] R413
R413-*1
33 50V 50V
NC_5 6 10 READY
IF_P
8 IF[N] PAL
R414
NTSC
R414-*1
33
10
7 IF_N
IF_AGC
9 NC_2 Close to the tuner
DIF[P] NC_3
2013.11.27 by BJ.KIM
10 9
DIF[N]
11
A1 B1
A1 B1
B1 A1 47
B1 A1
SHIELD
12
SHIELD
0 R402
NTSC
Size Up
NTSC
Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
TBD
AUAMP_SCL
AUAMP_SDA
BLU_CURRENT_CTL
HDMI1_SDA
HDMI1_D0+
HDMI1_D0-
HDMI1_CK+
HDMI1_HPD
SW_RESET
HDMI1_CK-
HDMI1_D1+
HDMI1_D1-
+3.3V_ST
*H/W OPTION
MUTE_AOUT
HW_RESET
I2S_MCLK
HD FHD
IR
44A/45A/450A
LED_B
HW_OPT1 LOW HIGH
MSTAR Vcc
PWM_DIM
DSUB_SDA
DSUB_SCL
+1.8V_M
2.2uF
READY
C552
R519 SMALL INCH BIG INCH
4.7K
HW_OPT2 LOW HIGH
GPIO69/I2S_OUT_MCK
KEY2
10K
KEY1
R535 1K
READY
R518 +1.2V_VDDC
100 R545
C549 R540
0.1uF 1K
R537
22
R536
22 C501 ST 1.26V
R531
100 10uF
+3.3V_M +3.3V_M
HDMI2
33
C553 10V
R528
0.1uF R542 R541
SAR3/GPIO72
SAR2/GPIO73
SAR1/GPIO74
SAR0/GPIO75
PWM1/GPIO25
PWM0/GPIO26
100 100
AVDD_DDR_2
R534 FHD BIG INCH
R546
HOTPLUG_D
R550 R590 C501 X5R(EAE31360401) -> X7R(EAE52158501)
100 1K
DDCDD_DA
To improve CST Issue
4.7K 4.7K 2013.11.27 by BJ.Kim
RXCKP_D
RXCKN_D
HWRESET
DDCA_DA
DDCA_CK
TESTPIN
R533
RX1P_D
RX1N_D
RX0P_D
RX0N_D
GPIO70
GPIO68
GPIO67
0 HW_OPT1 HW_OPT2
HD SMALL INCH
[EP]
IRIN
R551 R591
+1.8V_M DDR 1.8V
GND
CEC
4.7K 4.7K C503
22uF
6.3V
INV_ON
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
HDMI2 R522 100
USB_CTL
R500
33 DDCDD_CK 1 102 GPIO64 L502 ST 3.3V
HDMI1_SCL +3.5V_ST +3.3V_ST
BLM18PG121SN1D
RX2N_D 2 101 GPIO63 +3.3V_ST C504
HDMI1_D2-
THERMAL C548
10uF
10V
RX2P_D 3 100 AVDD_MOD_4 0.1uF SIDE_USB
HDMI1_D2+ 129 R552 0
SIDE_USB_DP
HOTPLUG_A 4 99 USB0_DP C501 X5R(EAE31360401) -> X7R(EAE52158501)
HDMI2_HPD REAR_USB_DP To improve CST Issue
REAR_USB
RXCKN_A 5 98 USB0_DM R553 0 2013.11.27 by BJ.Kim
HDMI2_CK- SIDE_USB_DN
SIDE_USB
RXCKP_A 6 97 SPI_CZ R554 0
REAR_USB_DN
HDMI2_CK+ SPI_CZ
REAR_USB
RX0N_A 7 96 SPI_DO R555 0
SPI_DO
HDMI2_D0-
RX0P_A 8 95 SPI_DI Add ROHM & ATMEL
SPI_DI
HDMI2_D0+
AVDD_MOD_1 SPI_CK 2013.11.27 by BJ.KIM
+3.3V_ST
9 94 SPI_CLK
C505
0.1uF
RX1N_A 10 93 PWM3/GPIO25 FLASH_WP Rohm_EEPROM
IC503-*1
BR24G256FJ-3
IC503-*2
AT24C256C-SSHL-T
HDMI2_D1-
HDMI2_D1+
R505
RX1P_A 11 IC501 92 PWM2/GPIO24
HW_OPT2
EEPROM(256K)
Renesas_EEPROM
IC503
A0
A1
1
2
8
7
VCC
WP
A0
A1
1
2
8
7
VCC
WP
HDMI2_D2-
HDMI2_D2+
RX2P_A
13
14
LGE6841 (ATV_13) 90
89 GPIO2
HDMI1_DET
POWER_SW
A0
1 8
VCC
C572 Atmel_EEPROM
R824 A1 WP 0.1uF
DDCDA_CK GPIO3 2 7
16V R569 R577
HDMI2_SCL
33
15 88 PANEL_ON 4.7K 4.7K
HDMI1 R527
ARC 16 87 GPIO4 10K A2 SCL
+1.2V_VDDC HW_OPT1
3 6
EEP_SCL
C506
0.1uF VDD 17 86 GPIO5 R529 100 VSS SDA
DSUB_DET
+3.3V_ST C507 R526
4 5
EEP_SDA
C512
4.7uF 0.1uF AVDD3P3_ADC 18 85 GPIO6 33 C573 C574
22pF
10V 22pF
EEP_SDA READY
R525 READY
HSYNC1 19 84 GPIO7 33
DSUB_HSYNC RGB/COMPONENT C508 EEP_SCL
R501 R516
33 0.047uF BIN1P 20 83 INT/GPIO65 100
COMMON_B POWER_DET
R523 C509 RGB/COMPONENT
470 1000pF SOGIN1 21 82 VDDC_2 C547 +1.2V_VDDC
RGB/COMPONENT
0.1uF
RGB/COMPONENT
DSUB_G GIN1P 22 81 LVB0M
R502
33
C510
0.047uF
RGB
R503
C511
0.047uF GIN1M LVB0P
RXB0- RXB0- SERIAL FLASH(8MB)
COMPONENT
RGB/COMPONENT RGB/COMPONENT
75
23 80 RXB0+
RXB0+
R515
0
RGB/COMPONENT COMPONENT
R503-*1 68 RIN1P 24 79 LVB1M
COMMON_R
R504 C550 RGB/COMPONENT RXB1- RXB1- +3.5V_ST
33 0.047uF VSYNC1 25 78 LVB1P FLASH_MXIC
DSUB_VSYNC RXB1+ IC502-*1
RXB1+
COMMON_VIN CVBS1 26 77 AVDD_MOD_3 MX25L6406EM2I-12G
R506
+3.3V_ST CS
1 8
VCC
C513
33 0.047uF CVBS0 27 76 LVB2M C546
0.1uF FLASH_WINBOND
SO/SIO1
2 7
HOLD
RXB2-
RXB2- WP SCLK
68 0.047uF
CVBSOUT1 LVBCKM
R581
10K
29 74 RXBCK-
RXBCK- R571 CS VCC
+3.3V_ST C515 AVDD_AU33 LVBCKP SPI_CZ 1 8
0.1uF 30 73 RXBCK+
100 C575
RXBCK+ 0.1uF
L506 AUREF 31 72 LVB3M SPI_DO
R572 DO[IO1]
2 7
%HOLD[IO3]
16V
C516 C517 RXB3-
RXB3- 100
120-ohm 10uF
16V
0.1uF VAG 32 71 LVB3P R576 WP[IO2] CLK R574
RXB3+ FLASH_WP 3 6 SPI_CLK
RXB3+ 100 100
LINEIN_L1 33 70 LVB4M
GND DI[IO0] R575
4 5 SPI_DI
LINEIN_R1 34 69 LVB4P 100
C576
C520 2.2uF LINEIN_L3 35 68 LVA0M 0.1uF
AUDIO_LIN
RXA0- RXA0- 16V
READY
C522 R510 C521 2.2uF LINEIN_R3 36 67 LVA0P
220pF 220K AUDIO_RIN
RXA0+ RXA0+
R508
100 LINEOUTL3 37 66 LVA1M
MNT_L_AMP RXA1-
RXA1-
LINEOUTR3 38 65 LVA1P
MNT_R_AMP RXA1+
R509 RXA1+
100 DIODES-SUB
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
1
RESET_ROHM GND
IC504 ROHM-MAIN R561
JP501
JP502
JP503
JP504
BD48K28G 10K
GND
33
R520
33
R521
RXACK-
1M 470
RXACK+
RXA2+
RXA3+
RXA3-
RXA2-
C542 C560
0.1uF
NTSC
0.1uF
NTSC
+3.3V_ST
R513-*1
R514-*1
X501 PAL
C561
PAL
4.7uF
24MHz 4.7uF
R513
C562
R514 R517 +1.8V_M
10V
100 10V
100 10K R564
0
I2S_SCK
I2S_SDO
RXACK-
0
0
TUNER
RXA3+
RXA3-
RXA2-
TUNER_RESET
RXA2+
HW_RESET
RXACK+
TUNER
I2S_WS
R524
C531 C534 C535
TUNER_SCL
C530
TUNER_SDA
0 C563
TUNER
R563
62K
TUNER
IF_N
Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
TBD
+5V_USB
+3.3V_M
44A/45A/450A
LED_Driver_EN_3.3V LED_Driver_EN_5V
R628 R629 +19V
0 0 BLU_ON
DRIVER DRIVER
BOOST L601 D602
R627 33UH BR210
0
READY R602
R601 3K R604 DRIVER DRIVER 100V
10K 1K C606 C607
DRIVER 10uF 10uF
C 1% DRIVER 25V 25V
R603 R605
C601
10K B Q601 100K
1000pF
INV_ON MMBT3904(NXP)
1%
50V
EMI Improve
DRIVER
E 0-> 3.3ohm(12.12.25)
IC601 3.3-> 5.6ohm(12.12.25)
VOUT
DT1641AS [EP]GND
D
DRIVER DRIVER DRIVER
DRIVER
R606 C616 R620 Q602
560K EN VIN 1uF 5.6 G AOD478
1 24 25V
DRIVER_Only 24inch(OVP)
THERMAL
1% R607-*2 S
33K DRIVER
25
1% OVP VREF C614
2 23
1uF
DRIVER_Except 24/28inch(OVP) DRIVER
DRIVER_Only 28inch(OVP) C602 25V
R607
DRIVER_Only 20.7 BOE_BM(OVP) R607-*1 1000pF NC_1 CS
27K 3 22
R607-*3 24K 1% 50V
47K 1% R618
1%
PGND_1 NDRV 0.1
DRIVER 4 21
R608 1%
100 DRIVER DRIVER
PWM_DIM READY
READY
C603
PGND_2
5 20
RSS
DRIVER
R616 R617
VA601
VA603
VA604
VA605
VA606
VA602
VA607
1/16W 1/16W 1/16W
20.7_BOE(BM) 22_LGD_BM 20.7_BOE 22_LGD_P15
READY
READY
READY
READY
READY
READY
READY
READY
R612-*13 R612-*12 R612-*11 R612-*9
2.7K 1% 2.49K 1% 33K 1% 18K 1%
1/16W 1/16W 1/16W
100V 100V
05002HR-H12J05
12
11
10
1
6
P601
P602
8CH
13
7
Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
TBD
44A/45A/450A
19V TO ST3.3V DCDC CONVERTER
+19V
IC701
MP2315GJ
R702
100K
** 3.5V_ST -> 1.26V VDDC
R701 R705 V0 = 0.8*(1+(R2/R1))
JK700
JP701 47K AAM
1 8
FB 33K +3.5V_ST IC704
KJA-DC-1-0032 AP7173-SPG-13 HF(DIODES)
+3.5V_ST +1.2V_VDDC OUT:1.26V
4 IN VCC [EP]
4 2 NEW 7
L702
10uH
2 2 C701
68uF
C703
10uF
25V
C704
0.1uF
SW
3 3A 6
EN/SYNC IN
1 8
OUT
THERMAL
35V 25V
C706 R706
ZD702
1 GND BST C707 C708 C709 2013.08.07 PG FB R1
9
1 20130528 cJ.LIM 0.1uF
5V
4 5 10uF 10uF 0.1uF 5.1K 5.6B->5V 2 7
25V 25V C742
R704 10V 10V READY->APPLY 1% ZD703
R703 1% 10uF
20K 1% R740 2.5V Add for imporving main IC burn Issue.
68 R707 VCC SS R741 10V
3 6 2.7K
27K
4.7K
JP702 C705 C746
1% R744 560pF
0.1uF X5R(EAE31360401) -> X7R(EAE52158501) 10K EN GND 50V
50V To improve CST Issue. 4 5
2013.11.27 by BJ.KIM
C740
R708 10uF
10K 10V X5R(EAE31360401) -> X7R(EAE52158501)
To improve CST Issue.
1%
2013.11.27 by BJ.KIM
X5R(EAE31360401) -> X7R(EAE52158501)
To improve CST Issue.
2013.11.27 by BJ.KIM
D
+3.3V_M
IC702 READY
C724
BOOST_EN
MP2315GJ 0.47uF
16V C
R747
10K B Q711
R720 R724
47K AAM FB 33K POWER_SW MMBT3904(NXP)
1 8
L720 E
10uH
IN VCC
+19V 2 NEW 7 P_12V
ZD701
PANEL_12V
3A
READY
C727
15V
D
S
S
47K
C722
0.1uF
PANEL_12V
R727
1%
PANEL_5V
** Switch Panel-Vcc
10K
G
G
50V 1% R726-*1
33K
1%
P_12V
FET Multi_AO3407B
PANEL_5V Q720 PANEL_VCC
R727-*1
15K AO3407B
1%
D
PANEL_12V C761 READY
4.7uF_25V_Madrian(Not Used) R765 R766
R767 0.1uF 3.3K 4.7K
PANEL_12V PANEL_5V C760 16V
24K R761 C760-*1
G
Q722 R761-*1 4.7uF
C MMBT3904(NXP) 39K 120K 4.7uF
PANEL_5V 25V
16V 4.7uF_16V(Use)
R767-*1 B
R771 2K PANEL_12V C760 X5R(EAE58111501) -> X7R(EAE62772301)
19V TO USB 5V DCDC CONVERTER 20130821 20K
D802
R761-*2
75K To improve CST Issue.
E BAT54C 2013.11.27 by BJ.KIM
IC709 C777 +3.3V_M A2 PANEL_5V For 20LB450A
MP2315GJ 1uF C
2013.08.09 READY 10V
APPLY -> READY A1
DCM -> CCM R770 R774
47K AAM FB 33K PANEL_12V
1 8 R762
L710 L770 PANEL_5V 39K
PANEL_5V
+19V UBW2012-121F
IN VCC
10uH R768
0 R762-*1
PANEL_5V For 20LB450A
R762-*2
2 NEW 7
+5V_USB 20K 12K
+5V_USB_Zener_KDZ5.6V
+5V_USB_Zener_UDZS5.6B
C770 C771 SW
3A EN/SYNC C774 C775 C776 R775
R762-*3
ZD700
5.6V
3 6 0.1uF C
5.6B
C772 R777
0.1uF 15K
50V
1%
Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
TBD
44A/45A/450A
22/26 HD
P801
27.5 HD(NOT_HEESUNG)
+24V_BLU SM14B-SRSS-TB P802
JP801 20022WR-14A00
24V 1
1
24V 2
+19V
2
BOOST BOOST +24V_BLU 24V 3
L801 D801
10uH BR210 3
24V 4
100V
BOOST READY
C802 C803 BOOST 4
BOOST BOOST READY
C804 BOOST BOOST
10uF 0.1uF R812 R813 24V
100pF 220K 30K C811 C814 C815 5
25V 25V
68uF 1uF 1uF
5
50V 35V 50V 50V
BOOST GND
BOOST BOOST C816 6
IC801 R814 270pF
TPS40210DGQR [EP] 10 50V 6
GND
7
RC VDD 7
1 10
GND 8
BOOST
THERMAL
BOOST
R801 C805
8
11
10K 0.22uF SS BP
2 9
D GND 9
BOOST BOOST BOOST
16V
R802 R811 Q801
1K DIS/EN GDRV 5.6 9
3 8 G AOD478
BOOST_EN GND 10
BOOST S
R810 JP802 READY
COMP ISNS 1K R820 10
4 7 100 ERROR_OUT 11
BOOST READY
BOOST C809 C810 BLU_ON
BOOST
READY
BOOST
R808
R809
0.1
READY
0.1uF
R821
R822 NC
12.07.03 To improve backlight blinking 4.7K 25V 13
BOOST JP804
BOOST R807
0
C1103 47pF->2200pF 13
R805 51K
C1105 47pF->Apply PWN_DIM
R1103 18K->470K PWM_DIM 14
470K
BOOST 14
R806 READY 15
1.5K C820
1uF 15
GND
10V
Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes