Escolar Documentos
Profissional Documentos
Cultura Documentos
Page 1 of 6
Output Format,
Specifications Pin C
Referenced to
Electrical
Pin B
Sensitivity – Main
loop (Signal One) Voltage, Acceleration vibration
0.0 to 25.4 mm/s (0 to 1.0 in/s) Note: The Dynamic Signal Negative (Pin B)
± 10%, broadband rms (root mean requires isolation from any grounding. If
square) this terminal is grounded, the 4-20 mA
loop will short, resulting in no output.
[4 mA equals 0.0 mm/s and
20 mA equals 25.4 mm/s] Frequency
Response
Output Format,
Pin A Referenced 2.5 Hz to 10 kHz (150 cpm to 600
to Pin B kcpm) ± 10%
4 to 20 mA current loop Velocity Linearity
vibration
±1%
Excitation
Output Bias
Voltage
Referenced to
12 to 30 Vdc (current limited to 40 Pin B
mA)
2.5 V ± 0.1 V
Note: This product is for use with PLCs, DCS
Full Scale Range
and SCADA systems that have internal
power supply that are typically current 196m/s2 (20 g’s) peak
limited in the range of 30 mA to 35 mA.
Velocity Range
Settling Time 420 mm/s (16.5 in/s) peak
Less than 15 seconds within 2% of Mounted
final value Resonant
Connector Wiring Frequency
Convention Greater than 12 kHz
Pin A: 4-20 mA Positive Loop Transverse
Pin B: 4-20 mA Negative Loop Sensitivity
and common for Dynamic Less than 5% of sensitivity
Signal
Sensing
Pin C: Dynamic Signal in voltage, Element Type
unbuffered
Ceramic / Shear
Frequency
Response
10 Hz to 1 kHz (600 cpm to 60
kcpm) ± 10%
Sensitivity –
Dynamic Signal
(Signal Two)
10.2 mV/m/s2 (100 mV/g) ± 5%
Page 2 of 6
Environmental Limits Physical
Operating Weight
Temperature
131 g (4.62 oz), typical
Range
Diameter
-40 °C to +85 °C
(-40 °F to +185 °F) 25.4 mm (1.00 in)
Electrical Height
Isolation
66.0 mm (2.60 in)
Greater than 108 ohms
Case Material
Isolation
316L stainless steel
Breakdown
Voltage Connector
600 Vrms with less than 1 mA 3-pin MIL-C-5015, 316L stainless
leakage current steel
Shock Mounting Hole
Survivability in Body
9.810 m/s2 (1.000 g peak), 1/4-28 UNF
maximum drop test
Mounting
Note: This part typically mounts directly to Threads
the machine via a stub. Customers can use
M6 X 1 SI
this device with a mag-base, but must take
care not to “snap” the unit onto the machine. M8 x 1.25 SI
This snapping action can create a very large
¼-28 UNF
spike signal that can damage the
electronics. Rolling the mag-base onto the Note: The above stud adapters are
machine greatly reduces the spike signal so provided with each device. Other
that the unit should not have any issues. adapters are available if needed. Please
see the Studs and Adapters section below,
Sensor Seal or contact the Custom Products Division.
Hermetically sealed
Mounting
Relative Humidity Torque
of Transmitter
4 to 7 N-m (35.4 to 62.0 in-lbf)
To 100% non-submerged
Connector
Magnetic Field Wiring
Sensitivity Convention
Less than 20 μm/s/gauss (790 Pin A: 4-20 mA Loop Power
μin/s/gauss) peak (Positive with reference
to Pin B)
Less than 14.7 mm/s2/gauss (150
μg/gauss) peak Pin B: 4-20 mA Loop Return
(Negative/ return for
[base on 50 gauss, 50 - 60 Hz]
Dynamic Signal)
Pin C: Dynamic Signal
(Unbuffered, referenced
to Pin B)
Page 3 of 6
Compliance and Certifications Product Description
EMC Seismic Transmitter
European Community Directives
177230-AA-BB-CC
EMC Directive 2004/108/EC
Option Descriptions
Standards:
AA: Measurement Range
EN 61326-2-3:2006
00 0 – 12.7 mm/s (0 – 0.5 in/s)
EN 61326-2-1:2006
01 0 – 25.4 mm/s (0 – 1.0 in/s)
Hazardous Area Approvals 02 0 – 50.8 mm/s (0 – 2.0 in/s)
North America: BB: Frequency
Ex nL IIC T4 01 10 Hz to 1 kHz (600 to 60 kcps)
AEx nA IIC T4 rms
Class I, Div 2, Groups A, B, C, D 02 3 Hz to 1 kHz (180 to 60 kcps)
Ex nL IIC T4: Class I, Zone 2 pk
Ex ia, IIC T4 CC: Approvals
AEx ia IIC T4 05 Multiple Approvals (CSA, ATEX,
Class I, Div 1, Groups A, B, C, D; and IECEx)
Class II, Div 1, Groups E, F, and G;
Class III, Div 1
Product Description
Ui ≤ 28V, Ii ≤ 120 mA, Pi ≤ 1W,
Ci ⋲ 0, Li ≤ 121.06 μH Interconnect Cable without Armor
T4 @ -40°C ‹ Ta ‹ 80°C 16925-AA
Europe: Option A description
II 1 G Ex ia IIC T4 Ga
A: Length in feet
II 3 G Ex nA IIC T4 Gc
Order in increments of 1 foot (0.3 m)
Ui ≤ 28V, Ii ≤ 120 mA, Pi ≤ 1W, Minimum length: 3 feet (0.91 m)
Ci ⋲ 0, Li ≤ 121.06 μH Maximum length: 99 feet (30.2m)
T4 @ -40°C ‹ Ta ‹ 80°C Example: 2 5 = 25 feet
IECEx:
The following are standard lengths
Ex ia IIC T4 Ga Feet Metres (approx.)
Ex nA IIC T4 Gc 12 3.6
15 4.5
Ui ≤ 28V, Ii ≤ 120 mA, Pi ≤ 1W, 17 5.0
Ci ⋲ 0, Li ≤ 121.06 μH 20 6.0
T4 @ -40°C ‹ Ta ‹ 80°C 25 7.6
30 9.0
For further certification and approvals information please visit the
following website: 33 10.0
www.ge-mcs.com/bently 50 15.2
99 30.0
Ordering Information NOTE: Non-standard/custom lengths
can also be ordered at additional cost
Country specific approvals may be available. Please
consult your local Customer Care Representative for
more information.
Page 4 of 6
Product Description Wire (3-wire with shield)
Interconnect Cable with Armor 3-conductor 18 to 22 AWG cables
16710-AA with a 0.01” minimum outer
jacket and inner wire insulation,
Option A description and 80% minimum coverage
A: Length in feet shield. Insulation rating should be
600 V minimum.
Order in increments of 1 foot (0.3 m)
Minimum length: 3 feet (0.91 m) Mil-W-16878/4 (Type E):
Maximum length: 99 Feet (30.2m) Sonic/Thermax
Example: 2 5 = 25 feet
www.thermaxcdt.com
The following are standard lengths 18 AWG -
Feet Metres (approx.)
12 3.6 P/N: 18-TE-1930 (3) SXE
15 4.5 22 AWG -
17 5.0
20 6.0 P/N: 22-TE-1934 (3) SXE
25 7.6 Standard Wire and Cable Co.
30 9.0
www.std-wire.com
33 10.0
50 15.2 18 AWG -
99 30.0
P/N: 1100-88T
NOTE: Non-standard/custom lengths
can also be ordered at additional cost 22 AWG -
P/N: 1100-66T
Accessories
Belden
The parts listed below are possible vendor sources for the
supporting hardware. You can use this information as a www.belden.com
reference and select the vendor that you wish to use.
18 AWG -
3-Pin Connector (MIL-C-5015): P/N: 83336
Base 22 AWG -P/N: 83334
Cannon (ITT industries): Studs and Adapters:
www.ittcannon.com 89139-01 M-M ¼-28 UNF to ⅜-24 UNF
Standard Stud
P/N: CA3106R-10SL-3S F97 or P/N:
MS3106R-10SL-3S 128038-01 M-M ¼-28 UNF to ⅜-24 Hex
Plate Stud (1-⅜” X 0.25”)
Shell
146396-01 F-M ¼-18 NPT to ¼-28 Adapter
Sunbank Co.
146394-01 F-M ¼-28 UNF to ¼-18 NPT
www.sunbankcorp.com
Adapter
Glenair, Inc.
37439-01 F-M ¼-28 UNF to ¼-28 UNF
www.glenair.com Mounting Base
Contact a vendor with above part 164373 M-M ¼-28 UNF to ¼-28 UNF
number and ask for their part that Standard Stud with Brass Tip
fits your application
135826-01 M-M ¼-28 UNF to M10 X 1.0
Standard Stud
Page 5 of 6
Graphs and Figures
Note: All dimensions shown are in millimetres (inches) except as noted.
C A
* Denotes a trademark of Bently Nevada, Inc., a wholly owned subsidiary of General Electric Company.
Page 6 of 6