Você está na página 1de 3

Mar.

2019
EPICON ZINC RICH PRIMER B-2 No. 1034
(EPZR B-2)
EPICON ZINC RICH PRIMER B-2, a two-pack primer, based on a combination of metallic zinc,
epoxy resin and hardener. It dries quickly and gives adequate preliminary protection of steel after
sand- or shot-blasting. This primer is completely compatible with almost all type of
coatings(except for oleoresinous paint, vinyl-based paint, and inorganic paint).
This primer has good workability and good adhesion with almost all type of over coatings.
Therefore, this primer is suitable for touch-up coating.
TECHNICAL DATA
Type Epoxy zinc rich primer
RecommendedUse As a primer for protection of blast-cleaned steel plates used for under water area of
outer hull and touch-up primer for zinc silicate shop primer.
Information Mixing Ratio : Base : Hardener = 70 : 30 [by volume]
Color : Grey, Green
Flash Point : Base = 10.0, Hardener = 10.0 [˚C]
Density : 1.72 [g/mL] (ISO:2811)
Volume solids (VS) : 43(+/-2) [volume %] (ISO:3233)
VOC : 500 [g/L] (Method24)
Coverage(Theoretical): 0.032 - 0.058 [L/m2]
Film Thickness : WET 35 - 58 [microns]
DRY 15 - 25 [microns]
(DFT 18microns) o
5 C
o
10 C
o
20 C
o
30 C
Drying Time Set-to-touch 8mins. 7mins. 4mins. 3mins.
Hard Dry 4hrs. 3hrs. 2hrs. 1.5hrs.
Painting Interval Min 24hrs. 20hrs. 16hrs. 10hrs.
Max 180days 180days 180days 150days
Pot Life 72hrs. 60hrs. 48hrs. 24hrs.
Condition Method of Application : Airless spray, Brush, Roller
of Weather : Temperature:-5 - 40 ˚C, Humidity:Maximum 85 %RH, Dew Point
Application +Minimum 3 degC
For Airless Spray : Viscosity : (Fc#4)9 - 13[sec]
Tip No. : (GRACO)517 - 721
Paint Output Pressure: 8 - 20[MPa]
Spray Speed : 60 - 160[cm/sec]
Thinner : EPOXY THINNER A,
Thinning: 0 - 25 % by Volume
Recommendable New building : Dependent on yard procedures. Please consult your
Surface Preparation: CMP representative.
Repair/Maintenance : Remove oil and grease etc. Remove salt and the
other contaminants by (high pressure) fresh water cleaning and
completely dry. Clean damaged area by abrasive blasting to the
standard Sa2 1/2 (ISO 8501-1:2007) minimum or power tooling to St3
(ISO 8501-1:2007).
Water jetting : Consult your CMP representative for recommendations.
Type and degree of surface preparation depends on type and
condition of actual substrate and on desired performance.
Good results can also be obtained on slightly corroded steel, even on
damp (drying) surfaces.
Use in accordance with standard worldwide marine specifications.
Preceding Coats : -
Subsequent Coats : Most of our products or the equivalents (except oleoresinous paint,
vinyl-based paints and inorganic zinc paint)
EPICON ZINC RICH PRIMER B-2 (Mar.2019rev )

Packaging Two pack product


Notes 1.Ventilation shall be maintained from coating application until the completion of curing in order
to remove residue of solvents and promote curing.
2.Agitate Base with a power agitator until it is turned homogeneous, and then combine entire
contents of Hardener with Base and mix thoroughly with power agitator. Then add appropriate
thinner and mix thoroughly.
3.Wet film thickness is reference only (unmeasurable)
4.In case that (1) epoxy coating is overlapped on this product applied at the block end (200mm
width in general), or (2) epoxy coating is overcoated on this product applied as touch-up at the
damages,
it is recommended that overcoatable interval should be kept for more than 1 hour at 20˚C.
5.Application at temperature down to -5˚C is possible, but curing time takes longer and full
cure will be reached when temperature increase.
6.For the PSPC use, please refer to PSPC's TDS.
7.Density, VS and VOC are measured from product samples without thinning. Values may vary
depending on color, manufacturing process, local regulations, etc.
This product should be used only by professional applicators. Consult the current Chugoku Marine Paints Safety Data Sheets.
Follow all local or national health, safety and environmental regulations. Observe all safety labels on packaging and containers.
Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only at ventilated
areas. Handle with care.
This data sheet contains the best and latest of our knowledge on the date of issue on our laboratory in Japan testing and practical
application experience, and subject to change without notice. Since the paints are used under unexpected circumstances in some
cases, guarantee can not be given except on the quality of those paints themselves.

Você também pode gostar