Escolar Documentos
Profissional Documentos
Cultura Documentos
Issue 01
Date 2015/03/25
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All
products, services and features described in this document may not be within the purchase scope or the usage scope. Unl
specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without
guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the preparation of this
ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute
any kind, express or implied.
spective holders.
Version
The corresponding product versions of this document are as follows:
NE Type:
Match Version:
NE Version:
Intended Audience
This document is intended for:
Network operators
Field engineers
System engineers
Network planners
Structure
AlarmID Alarm ID.
Information used for locating an alarm, such as the subrack number, slot number, subsystem
Location Information
number, and fault causes.
System Actions Actions taken by the system after the alarm is generated.
ID.
name.
ation used for locating an alarm, such as the subrack number, slot number, subsystem
er, and fault causes.
meaning.
handling suggestions.
2286 CDU VSWR Critical Ala 2 5 Site No. = %d, Board Typ
2288 FCU Staggering Failure 2 5 Site No. = %d, Board Typ
2290 FCU Frequency Point Pr2 7 Site No. = %d, Board Typ
2292 EDU VSWR Alarm 3 7 Site No. = %d, Board Typ
2294 EDU VSWR Critical Alar 2 7 Site No. = %d, Board Typ
2296 EDU LNA Alarm 3 5 Site No. = %d, Board Typ
2298 EDU TTA Alarm 3 5 Site No. = %d, Board Typ
2300 Board Type Mismatch Al 2 5 Site No. = %d, Board Typ
2302 CDU Band Mismatch AR2 5 Site No. = %d, Board Typ
2304 PMU extended 60 alarm 4 5 Site No. = %d, Board Typ
2306 PMU extended 61 alarm 4 5 Site No. = %d, Board Typ
2308 PMU extended 62 alarm 4 5 Site No. = %d, Board Typ
2310 PMU extended 63 alarm 4 5 Site No. = %d, Board Typ
2312 PMU extended 64 alarm 4 5 Site No. = %d, Board Typ
2314 PMU extended 65 alarm 4 5 Site No. = %d, Board Typ
2316 PMU extended 66 alarm 4 5 Site No. = %d, Board Typ
2318 PMU extended 67 alarm 4 5 Site No. = %d, Board Typ
2320 PMU extended 68 alarm 4 5 Site No. = %d, Board Typ
2322 PMU extended 69 alarm 4 5 Site No. = %d, Board Typ
2324 Battery Power Off Alarm 4 1 Site No. = %d, Board Typ
2326 Battery Fuse Broken Ala 3 1 Site No. = %d, Board Typ
2328 PMU extended 6C alarm4 5 Site No. = %d, Board Typ
2330 DC Lowvoltage Alarm 2 1 Site No. = %d, Board Typ
2332 DC Overvoltage Alarm 2 1 Site No. = %d, Board Typ
2334 PMU Communication Al 2 5 Site No. = %d, Board Typ
2336 PMU extended 70 alarm 4 5 Site No. = %d, Board Typ
2338 Rack Low Temperature 2 2 Site No. = %d, Board Typ
2340 Rack High Temperature 2 2 Site No. = %d, Board Typ
2342 Rack Low Humidity Alar 3 2 Site No. = %d, Board Typ
2344 Rack High Humidity Ala 2 2 Site No. = %d, Board Typ
2346 Rack Smog Alarm 2 2 Site No. = %d, Board Typ
2348 Rack Infrared Alarm 2 2 Site No. = %d, Board Typ
2350 Rack Gate Magnetism A 2 2 Site No. = %d, Board Typ
2352 Water Immerse Alarm 2 2 Site No. = %d, Board Typ
2354 Fan Alarm 2 5 Site No. = %d, Board Typ
2356 Battery high temperatur 2 1 Site No. = %d, Board Typ
2358 AC Overvoltage Alarm 2 1 Site No. = %d, Board Typ
2360 AC Lowvoltage Alarm 2 1 Site No. = %d, Board Typ
2362 No Mains Supply Alarm 2 1 Site No. = %d, Board Typ
2364 EMU Failure Alarm 2 5 Site No. = %d, Board Typ
2366 SPD Failure Alarm 2 5 Site No. = %d, Board Typ
2368 Fire Alarm 2 2 Site No. = %d, Board Typ
2370 Smog Alarm 2 2 Site No. = %d, Board Typ
2372 Guard Against Theft Ala 2 2 Site No. = %d, Board Typ
2374 Water Immersed Alarm 2 2 Site No. = %d, Board Typ
2376 Over Temperature Alarm2 2 Site No. = %d, Board Typ
2378 Low Temperature Alarm 2 2 Site No. = %d, Board Typ
2380 High Humidity Alarm 2 2 Site No. = %d, Board Typ
2382 Low Humidity Alarm 2 2 Site No. = %d, Board Typ
2384 EAC Communication Ala2 5 Site No. = %d, Board Typ
2386 Sixteenth Extended I/O 4 2 Site No. = %d, Board Typ
2388 Seventeenth Extended I 4 2 Site No. = %d, Board Typ
2390 Eighteenth Extended I/O4 2 Site No. = %d, Board Typ
2392 Nineteenth Extended I/O4 2 Site No. = %d, Board Typ
2394 Twentieth Extended I/O 4 2 Site No. = %d, Board Typ
2396 Twenty-First Extended I 4 2 Site No. = %d, Board Typ
2398 Twenty-Second Extended4 2 Site No. = %d, Board Typ
2400 Twenty-Third Extended I4 2 Site No. = %d, Board Typ
2402 First Extended I/O Alarm4 2 Site No. = %d, Board Typ
2404 Second Extended I/O Al 4 2 Site No. = %d, Board Typ
2406 Third Extended I/O Alar 4 2 Site No. = %d, Board Typ
2408 Fourth Extended I/O Ala 4 2 Site No. = %d, Board Typ
2410 Fifth Extended I/O Alarm4 2 Site No. = %d, Board Typ
2412 Sixth Extended I/O Alar 4 2 Site No. = %d, Board Typ
2414 Seventh Extended I/O A 4 2 Site No. = %d, Board Typ
2416 Eighth Extended I/O Ala 4 2 Site No. = %d, Board Typ
2418 Ninth Extended I/O Alar 4 2 Site No. = %d, Board Typ
2420 Tenth Extended I/O Alar 4 2 Site No. = %d, Board Typ
2422 Eleventh Extended I/O A4 2 Site No. = %d, Board Typ
2424 Twelfth Extended I/O Al 4 2 Site No. = %d, Board Typ
2426 Thirteenth Extended I/O 4 2 Site No. = %d, Board Typ
2428 Fourteenth Extended I/O4 2 Site No. = %d, Board Typ
2430 Fifteenth Extended I/O 4 2 Site No. = %d, Board Typ
2432 PSU Communication Ala3 7 Site No. = %d, Board Typ
2434 PSU Fault Alarm 2 1 Site No. = %d, Board Typ
2436 PSU Safeguard Alarm 2 1 Site No. = %d, Board Typ
2438 PMU extended A3 alarm4 5 Site No. = %d, Board Typ
2440 PMU extended A4 alarm4 5 Site No. = %d, Board Typ
2442 PMU extended A5 alarm4 5 Site No. = %d, Board Typ
2444 PMU extended A6 alarm4 5 Site No. = %d, Board Typ
2446 PMU extended A7 alarm4 5 Site No. = %d, Board Typ
2448 Optical Receive Channel1 4 Site No. = %d, Board Typ
2450 Optical Transmit Channe1 4 Site No. = %d, Board Typ
2452 E1 Outboard Alarm 2 4 Site No. = %d, Board Typ
2454 E1 Inboard Alarm 2 4 Site No. = %d, Board Typ
2456 TEU Communication Ala3 7 Site No. = %d, Board Typ
2546 TCU Board DC/DC Powe2 5 Site No. = %d, Board Typ
2548 TCU Temperature Senso2 5 Site No. = %d, Board Typ
2550 Relay or Contactor Alar 2 5 Site No. = %d, Board Typ
2560 PBU VSWR Alarm 2 5 Site No. = %d, Board Typ
25600 Monitoring Device Maint 2 8 Cabinet No. = %d, Subrack
25601 Monitoring Device Hardw2 5 Cabinet No. = %d, Subrack
25602 Sensor Failure 2 5 Cabinet No. = %d, Subrack
2562 PBU Over Temperature 2 5 Site No. = %d, Board Typ
25620 Monitoring Device Powe 2 5 Cabinet No. = %d, Subrack
25621 Power Supply DC Output2 1 Cabinet No. = %d, Subrack
25622 Mains Input Out of Rang2 1 Cabinet No. = %d, Subrack
25623 Load Disconnect 4 1 Cabinet No. = %d, Subrack
25624 Battery Power Unavailab4 1 Cabinet No. = %d, Subrack
25625 Battery Current Out of 2 1 Cabinet No. = %d, Subrack
25626 Power Module Abnormal4 1 Cabinet No. = %d, Subrack
25628 AC Surge Protector Faul2 1 Cabinet No. = %d, Subrack
25630 Power Module and Monit2 1 Cabinet No. = %d, Subrack
25631 Load Fuse Broken 2 1 Cabinet No. = %d, Subrack
25632 Battery Cabin Heater Fau2 1 Cabinet No. = %d, Subrack
25633 PMU Internal Interface 2 1 Cabinet No. = %d, Subrack
25634 Battery Not In Position 2 1 Cabinet No. = %d, Subrack
25635 Lithium Battery Failure 2 1 Cabinet No. = %d, Subrack
25636 Loss of Power Supply 4 1 Cabinet No. = %d, Subrack
2564 PBU Low Forward Power2 5 Site No. = %d, Board Typ
25650 Ambient Temperature Un3 2 Cabinet No. = %d, Subrack
25651 Ambient Humidity Unacc3 2 Cabinet No. = %d, Subrack
25652 Cabinet Temperature Un3 2 Cabinet No. = %d, Subrack
25653 Cabinet Humidity Unacc 3 2 Cabinet No. = %d, Subrack
25654 Battery Temperature Un 3 1 Cabinet No. = %d, Subrack
25655 Cabinet Air Outlet Temp 3 2 Cabinet No. = %d, Subrack
25656 Cabinet Air Inlet Tempe 3 2 Cabinet No. = %d, Subrack
25657 TEC Cooler Fault 2 2 Cabinet No. = %d, Subrack
25659 Heater Hardware Fault 3 2 Cabinet No. = %d, Subrack
2566 PBU extended E3 alarm 4 5 Site No. = %d, Board Typ
25670 Water Alarm 1 2 Cabinet No. = %d, Subrack
25671 Smoke Alarm 1 2 Cabinet No. = %d, Subrack
25672 Burglar Alarm 1 2 Cabinet No. = %d, Subrack
25673 Fan Stalled 2 5 Cabinet No. = %d, Subrack
2568 PBU FLASH Memory Al 2 5 Site No. = %d, Board Typ
25696 Diesel Generator Low Fu2 5 Cabinet No. = %d, Subrack
25697 Diesel Generator Startup2 5 Cabinet No. = %d, Subrack
2570 EPLD Total Loaded Time4 5 Site No. = %d, Board Typ
25710 Loss of Solar Array 2 5 Cabinet No. = %d, Subrack
4810 Main Control Module Con2 5 Site No. = %d, Board Typ
4812 Optic Module Abnormal 2 5 Site No. = %d, Board Typ
4832 Faulty Clock Source for 2 6 Site No. = %d, Board Typ
4834 Clock Synchronization fo2 2 Site No. = %d, Board Typ
4836 E1/T1 Port Illegal Alarm 2 5 Site No. = %d, Board Typ
4838 Rack Type Mismatch Al 2 5 Site No. = %d, Board Typ
4840 Rack Over Hot Degrade 4 2 Site No. = %d, Board Typ
4842 BTS3012 Cabinet 3 Arre2 5 Site No. = %d, Board Typ
4844 BTS3012 Cabinet 4 Arre2 5 Site No. = %d, Board Typ
4846 BTS3012 Boolean 11 Al 4 2 Site No. = %d, Board Typ
4848 BTS3012 Boolean 12 Al 4 2 Site No. = %d, Board Typ
4850 BTS3012 Boolean 13 Al 4 2 Site No. = %d, Board Typ
4852 BTS3012 Boolean 14 Al 4 2 Site No. = %d, Board Typ
4854 BTS3012 Boolean 15 Al 4 2 Site No. = %d, Board Typ
4856 BTS3012 Boolean 16 Al 4 2 Site No. = %d, Board Typ
4858 BTS3012 Cabinet 6 Arre2 5 Site No. = %d, Board Typ
4860 BTS3012 Cabinet 7 Arre2 5 Site No. = %d, Board Typ
4862 BTS3012 Boolean 19 Al 4 2 Site No. = %d, Board Typ
4864 BTS3012 Boolean 20 Al 4 2 Site No. = %d, Board Typ
4866 BTS3012 Boolean 21 Al 4 2 Site No. = %d, Board Typ
4868 BTS3012 Boolean 22 Al 4 2 Site No. = %d, Board Typ
4870 BTS3012 Boolean 23 Al 4 2 Site No. = %d, Board Typ
4872 BTS3012 Boolean 24 Al 4 2 Site No. = %d, Board Typ
4874 BTS3012AE Boolean 1 A4 2 Site No. = %d, Board Typ
4876 BTS3012AE Boolean 2 A4 2 Site No. = %d, Board Typ
4878 BTS3012AE Boolean 3 A4 2 Site No. = %d, Board Typ
4880 BTS3012AE Boolean 4 A4 2 Site No. = %d, Board Typ
4882 BTS3012AE Boolean 5 A4 2 Site No. = %d, Board Typ
4884 BTS3012AE Boolean 6 A4 2 Site No. = %d, Board Typ
4886 BTS3012AE Boolean 7 A4 2 Site No. = %d, Board Typ
4888 BTS3012AE Boolean 8 A4 2 Site No. = %d, Board Typ
4890 BTS3012AE Boolean 9 A4 2 Site No. = %d, Board Typ
4892 BTS3012AE Boolean 104 2 Site No. = %d, Board Typ
4894 BTS3012AE Boolean 11 4 2 Site No. = %d, Board Typ
4896 BTS3012AE Boolean 124 2 Site No. = %d, Board Typ
4898 BTS3012AE Boolean 134 2 Site No. = %d, Board Typ
4900 BTS3012AE Boolean 144 2 Site No. = %d, Board Typ
4902 BTS3012AE Boolean 154 2 Site No. = %d, Board Typ
4904 BTS3012AE Boolean 164 2 Site No. = %d, Board Typ
4906 BTS3012AE Boolean 174 2 Site No. = %d, Board Typ
4908 BTS3012AE Boolean 184 2 Site No. = %d, Board Typ
4910 BTS3012AE Boolean 194 2 Site No. = %d, Board Typ
4912 BTS3012AE Boolean 204 2 Site No. = %d, Board Typ
6370 LOW Analog Input Signa4 2 Site No. = %d, Board Typ
6404 Fire Alarm 1 2 Site No. = %d, Board Typ
6406 Smog Alarm 1 2 Site No. = %d, Board Typ
6408 Guard Against Theft Ala 1 2 Site No. = %d, Board Typ
6410 Water Immersed Alarm 1 2 Site No. = %d, Board Typ
6412 Over Temperature Alarm2 2 Site No. = %d, Board Typ
6414 Low Temperature Alarm 2 2 Site No. = %d, Board Typ
6416 Over Humidity Alarm 2 2 Site No. = %d, Board Typ
6418 Low Humidity Alarm 2 2 Site No. = %d, Board Typ
6420 Board Communication A 2 2 Site No. = %d, Board Typ
6422 BTS3012 Boolean 16 al 4 2 Site No. = %d, Board Typ
6424 BTS3012 Boolean17 Ala4 2 Site No. = %d, Board Typ
6426 BTS3012 Boolean18 Ala4 2 Site No. = %d, Board Typ
6428 BTS3012 Boolean19 Ala4 2 Site No. = %d, Board Typ
6430 BTS3012 Boolean20 Ala4 2 Site No. = %d, Board Typ
6432 BTS3012 Boolean21 Ala4 2 Site No. = %d, Board Typ
6434 BTS3012 Boolean22 Ala4 2 Site No. = %d, Board Typ
6436 BTS3012 Boolean23 Ala4 2 Site No. = %d, Board Typ
6438 BTS3012 Boolean1 Alar 4 2 Site No. = %d, Board Typ
6440 BTS3012 Boolean2 Alar 4 2 Site No. = %d, Board Typ
6442 BTS3012 Boolean3 Alar 4 2 Site No. = %d, Board Typ
6444 BTS3012 Boolean4 Alar 4 2 Site No. = %d, Board Typ
6446 BTS3012 Boolean5 Alar 4 2 Site No. = %d, Board Typ
6448 BTS3012 Boolean6 Alar 4 2 Site No. = %d, Board Typ
6450 BTS3012 Boolean7 Alar 4 2 Site No. = %d, Board Typ
6452 BTS3012 Boolean8 Alar 4 2 Site No. = %d, Board Typ
6454 BTS3012 Boolean9 Alar 4 2 Site No. = %d, Board Typ
6456 BTS3012 Boolean10 Ala4 2 Site No. = %d, Board Typ
6458 BTS3012 Boolean11 Ala4 2 Site No. = %d, Board Typ
6460 BTS3012 Boolean12 Ala4 2 Site No. = %d, Board Typ
6462 BTS3012 Boolean13 Ala4 2 Site No. = %d, Board Typ
6464 BTS3012 Boolean14 Ala4 2 Site No. = %d, Board Typ
6466 BTS3012 Boolean15 Ala4 2 Site No. = %d, Board Typ
6468 BTS3012 Boolean24 Ala4 2 Site No. = %d, Board Typ
6470 BTS3012 Boolean25 Ala4 2 Site No. = %d, Board Typ
6472 BTS3012 Boolean26 Ala4 2 Site No. = %d, Board Typ
6474 BTS3012 Boolean27 Ala4 2 Site No. = %d, Board Typ
6476 BTS3012 Boolean28 Ala4 2 Site No. = %d, Board Typ
6478 BTS3012 Boolean29 Ala4 2 Site No. = %d, Board Typ
6480 BTS3012 Boolean30 Ala4 2 Site No. = %d, Board Typ
6482 BTS3012 Boolean31 Ala4 2 Site No. = %d, Board Typ
6484 BTS3012 Boolean32 Ala4 2 Site No. = %d, Board Typ
6486 -48V Power too High Al 3 2 Site No. = %d, Board Typ
6488 -48V Power too Low Ala 3 2 Site No. = %d, Board Typ
6490 Over Analog Input Signa4 2 Site No. = %d, Board Typ
6492 Low Analog Input Signal 4 2 Site No. = %d, Board Typ
6494 Over Analog Input Signa4 2 Site No. = %d, Board Typ
6496 Low Analog Input Signal 4 2 Site No. = %d, Board Typ
6498 Over Analog Input Signa4 2 Site No. = %d, Board Typ
6500 Low Analog Input Signal 4 2 Site No. = %d, Board Typ
6502 Over Analog Input Signa4 2 Site No. = %d, Board Typ
65033 SRAN Custom Environme 2 2 Site No. = %d
65034 SRAN Custom Environme 2 2 Site No. = %d
65035 SRAN Custom Environme 2 2 Site No. = %d
65036 SRAN Custom Environme 2 2 Site No. = %d
65037 SRAN Custom Environme 2 2 Site No. = %d
65038 SRAN Custom Environme 2 2 Site No. = %d
65039 SRAN Custom Environme 2 2 Site No. = %d
6504 Low Analog Input Signal 4 2 Site No. = %d, Board Typ
65040 SRAN Custom Environme 2 2 Site No. = %d
65041 SRAN Custom Environme 2 2 Site No. = %d
65042 SRAN Custom Environme 2 2 Site No. = %d
65043 SRAN Custom Environm2 2 Site No. = %d
65044 SRAN Custom Environme 2 2 Site No. = %d
65045 SRAN Custom Environm2 2 Site No. = %d
65046 SRAN Custom Environm2 2 Site No. = %d
65047 SRAN Custom Environm2 2 Site No. = %d
65048 SRAN Custom Environm2 2 Site No. = %d
65049 SRAN Custom Environm2 2 Site No. = %d
65050 SRAN Custom Environm2 2 Site No. = %d
65051 SRAN Custom Environm2 2 Site No. = %d
65052 SRAN Custom Environm2 2 Site No. = %d
65053 SRAN Custom Environm2 2 Site No. = %d
65054 SRAN Custom Environm2 2 Site No. = %d
65055 SRAN Custom Environm2 2 Site No. = %d
65056 SRAN Custom Environm2 2 Site No. = %d
65057 SRAN Custom Environm2 2 Site No. = %d
65058 SRAN Custom Environm2 2 Site No. = %d
65059 SRAN Custom Environm2 2 Site No. = %d
6506 DEMU Hardware Failure2 2 Site No. = %d, Board Typ
65060 SRAN Custom Environm2 2 Site No. = %d
65061 SRAN Custom Environm2 2 Site No. = %d
65062 SRAN Custom Environm2 2 Site No. = %d
65063 SRAN Custom Environm2 2 Site No. = %d
65064 SRAN Custom Environm2 2 Site No. = %d
65065 SRAN Custom Environm2 2 Site No. = %d
9768 nfcb not consistant with 2 2 Site No. = %d, Board Typ
9770 Parameter set collision 4 2 Site No. = %d, Board Typ
Possible Causes
The voltage of the primary power supply exceeds the adjustable range of the Power Distribution Frame (PDF).
The alarm switches are incorrectly set.The branch output switch of the PDF is off.
The lightning protection board is absent.The lightning protection board is damaged.
The sensor is faulty.The environment of the equipment room is abnormal, for example, the temperature is too high or too low, o
The power supply to a fan or the fan box is abnormal.
The low humidity may be caused by dry weather, use of indoor electric appliances such as heater, low temperature in the equi
The front door or rear door of the cabinet is open.
The temperature sensor is faulty.
The heat dissipation and air ventilation are poor in the equipment room.The cooling devices in the equipment room, such as th
The LED on the lower right corner of the fan box is red, indicating that the fan is faulty.The temperature in the equipment room
The speed regulation module in the fan box is faulty. The temperature sensor in the fan box is faulty.
The fan box is faulty.Either of two power inputs to the cabinet fails.
The equipment room is immersed in water.
The alarm threshold of the power supply is inappropriately set.The power supply cabinet is damaged.The AC power supply fai
The alarm threshold is inappropriately set.The temperature sensor of the Environment Monitoring Unit is damaged.The air con
The alarm threshold is inappropriately set.The humidity and temperature sensor of the Environment Monitoring Unit is faulty, c
The smoke sensor is faulty, causing a false alarm.The equipment room is on fire.
The sensor is faulty, causing a false alarm.Someone enters the equipment room.
The source 1PPS signal on the clock board is abnormal. The external environment causes the 1PPS signal alarm on the board
The clock source signals on the GCU/GCG board are abnormal.The external environment causes discontinuous transmission
When the line clock is unavailable, the clock signal on the board is lost.
When the clock from the backplane is unavailable, the clock signals transmitted from the backplane is lost. The alarm is gener
The input signal of the reference source is lost. The frequency offset of the input signal of the clock reference source is abnorm
The software of the GCG or GCU is faulty.The clock signal cables are not securely connected.The clock signal cables are faul
No clock source is configured.In <b>Auto Handover</b> mode, all configured clock reference sources are unavailable. In <b>A
The clock configuration is incorrect.The 8 kHz clock on the panel is faulty. The No. 0 8 kHz clock on the backplane is faulty. Th
The hardware of the clock phase-locked loop is faulty.The clock reference source is faulty.
The selected clock reference source does not transmit clock signals to the board. The clock signals output from the selected c
The synchronization time information is abnormal or the transmission of the information is abnormal. The DSP cannot properly
The board is faulty in hardware.The input signal of the clock source is lost.The frequency offset of the input signal of the clock
The reference clock source is not configured.The software of the active and standby GCUs/GCGs is faulty.The clock signal ca
Ethernet cables or fiber optic cables in a trunk group on an SCU connect to different subracks.Ethernet cables or fiber optic ca
The hardware of the local board or of the peer board is faulty.The local board or the peer board is not securely inserted. The b
The hardware of the local board or of the peer board is faulty.The local board or the peer board is not securely inserted.The ba
The OMU is not configured.The backplane is faulty.The OMU or SCU board is not securely inserted.One Ethernet cable that c
The broadcast packets overflow.
The peer board is faulty or abnormal.The Ethernet cable for the panel is disconnected or is not securely connected. The Ether
Negotiation fails between the local and peer ports because of inconsistency in the work mode or rate configured for both ports
The Ethernet cables connected to the GE ports on the SCU board panel are all disconnected, not securely connected, or fault
When the local board or the peer board is abnormal.When the board is loosely connected to the backplane, the GE link is faul
The port timeslot is in the loopback state.
The local board is faulty. The peer board is faulty.The board is not securely inserted. The peer board is not securely inserted.T
The software of the local or peer TNU board is faulty.The peer TNU board corresponding to the faulty link is not installed or is r
The hardware of the board is faulty.The hardware of the SCU board is faulty.The SCU board is faulty or not securely inserted.T
The power component is faulty.
The BIOS component is faulty.
The peer board that carries the faulty link is uninstalled.The clock signals transmitted to the service board from the SCU are fa
The peer board that carries the faulty link is uninstalled.The peer board that carries the faulty link is reset.The cable between t
The peer board is faulty and sends packets with incorrect source MAC addresses.The peer board is faulty and loops back the
A service board in another subrack has a hardware fault. As a result, the packets sent to the local board are looped back to the
One of the two boards is faulty.
The type of the board installed is inconsistent with the configured type.The board resets due to software faults.The system inh
The software is faulty.The board is faulty.The board subsystem fails to be started in a long time.
The active or standby network port is faulty.The active-standby arbitration component is faulty.The GE link inside the board is f
The [MML]RST SUBRACK[/MML] command is run. A command to reset the active SCU board is received, but a switchover be
The data configuration is erroneous.The E1/T1 port on the Ater interface is faulty.The interface board does not work normally.
A board is blocked.
The hardware of the board is damaged.The board is not securely inserted.
The hardware of the board is damaged.The setting of the DIP switch in the subrack is manually changed.The board is not sec
The sub-board is absent. The sub-board is not securely inserted. The hardware of the sub-board is damaged.
The fan is faulty.The heat dissipation part of the board is faulty.A vacant slot is not installed with a filler panel.The ambient tem
The antenna connected to the GPS receiver is disconnected. The antenna connected to the GPS receiver is short-circuited.
The almanac of the GPS receiver is invalid. The GPS receiver is faulty. As a result, one of the following may occur: The positio
The DSP software is abnormal when loading or starting the DSP.The DSP hardware is faulty.
The DSP is inhibited.
CPU occupancy alarm threshold of the subsystem is configured too low.Flow control switch is turn off.Flow control threshold o
The configuration data is incorrect.The software version of the board is inconsistent with that on the OMU.
The number of resources currently used reaches the alarm occurrence threshold of the capacity limit specified by the license.
The number of resources currently used exceeds the capacity limit specified by the license.
The hardware of the board is faulty.The backplane is faulty.The CPU at the peer end is overloaded.
The interface board does not work properly.The E1/T1 port on the Ater interface is faulty.
Board communication parts become faulty.
For details, see the causes of the related alarm.
The component for clock signal output is faulty.The clock bus of the backplane is faulty.The component for clock signal input is
The forwarding ratio of the interface board reaches or exceeds the alarm reporting threshold.
The external environment causes discontinuous transmission or loss of clock packets.The clock source signal from the GCU/G
The communication between subracks is abnormal.The data traffic of inter-subrack communication exceeds the overload thres
The configured board type is different from the actual board type.
The SCU board or the service board cannot be detected, is reset, or has a hardware fault.The SCU board or the service board
The fan is faulty. The filler panel is not installed in the empty slot. The heat dissipation of the board is not effective.The ambien
The version of rule lib is inconsistent with the configured version.The current version product is not compatible with the rule lib
prolonged usage of the hard disk
Processes stop abnormally.Services stop abnormally.The disk driver version does not match the hardware version.The board d
For details about the hardware failure cause, see the alarm cause of ALM-20243 Board Hardware Fault.
The original OMU fails, and the configuration data on the new active OMU is inconsistent with the configuration data on host b
The network segment on which the internal fixed IP address is located of the active OMU differs from that of the standby OMU
The hardware of the standby OMU is faulty.The OMU service on the standby OMU is not started.
The ftp_server module of the active OMU is abnormal.The database or operating system of the active or standby OMU is fault
The software version of the active OMU is inconsistent with the software version of the standby OMU during the version upgra
The OMU system is abnormal.
One of OMU's IP addresses is shared by another device in the live network, this alarm is generated.The debug network adapt
The service configurations of the operating system are incorrect.
The remaining space of the OMU logical disks is less than 10%. The remaining space of the /mbsc/weblmt logical disk is less
The network connection between the OMU and EMS is abnormal. The EMS is offline.
OMU and standby OMU is abnormal.The SNTP server is not configured.The internal network communication link between act
The FTP server module of the active OMU is abnormal. The software module of the standby OMU is abnormal.The OMU work
If the hardware type is network adapter ETH0 or ETH1, the actual duplex mode of the OMU network adapter is inconsistent wi
The subnet mask of the fixed IP address of the internal network is incorrect.The subnet mask of the virtual IP address of the in
The VLAN ID configured on the active OMU board for communication with the EMS or LMT is inconsistent with that configured
Changes are made in files under monitoring during software upgrades, driver upgrades, or operating system upgrades or switc
The type of the board in the subrack is inconsistent with that of the configured board.
One or more SSL certificate files are lost, damaged or expired.
The hot patch is not installed successfully. The software version of the host is inconsistent with that recorded in the version de
The license is activated in ineffective mode, and it does not take effect on the board.An error occurs during license activation.
<p>The ESN of the license file is inconsistent with the ESN of the system. </p><p>The OPC (index 0) corresponding to the ES
The data on the host is inconsistent with those in the data table of the OMU.
The network communication between the OMU and host board fails.The board is faulty or out of position.
The password of user [PARMNAME]emscomm[/PARMNAME] for the NE is inconsistent with that for the EMS.The network com
The license file is not activated.
The connection between the alarm box and workstation is faulty.The alarm box is powered off. The Convert Management Syst
The configuration data exceeds the capacity allowed by the license.
The [MML]ADD SUBRACK[/MML] command is executed. The [MML]SET CFGDATAINEFFECTIVE[/MML] command is execut
The configuration data exceeds the capacity allowed by the license.
The ESN of the NE is different from the ESN in the license file.
The program file, bootrom file, data file, DSP file, RuleLib file or patch file is updated on the OMU but not loaded to the board.
The feature exceeds the expiry date specified in the license file.
A feature exceeds the expiry date and reserving days specified in the license file.
The daily handshake message about the network license between the system and the EMS is lost.
The system lost synchronization information of GBTS licenses periodically delivered by the U2000.The U2000 managing the B
The fault on the peer BSC is not rectified.The peer BSC exits from the node redundancy group while the local BSC stays.
See [FILE]link894[/FILE].
The number of TRXs configured on the Abis interface board exceeds the board specification. As a result, the switching capabil
The Certificate Authority (CA) is not configured.The root certificate for verifying the CA is not configured.The network between
The control plane subsystem where the BTS is configured becomes unavailable.
One or more digital certificates will expire.
A digital certificate is lost, damaged, expired or ineffective.
A user enters the incorrect password for an account consecutively for certain times which exceeds the threshold.
The communication between the BSC and the VNP fails.The VNP fails.
The digital certificate at the peer end has expired or been revoked because the peer end did not update the certificate in time,b
The free space of the logical disk of the SAU is less than 10%.
Errors may occur on the SAU.
One of SAU's IP addresses is shared by another device in the live network.The debug network adapter (ETH2) of the SAU is c
The actual duplex mode of the SAU Ethernet adapter is inconsistent with the expected duplex mode of the SAU Ethernet adap
The OMU module is abnormal.The internal network adapter of the OMU board is faulty.Communication between the OMU and
<p>No default route is configured, or more than one default route is configured.</p><p>The gateway IP address of the default
OMU network transmission is abnormal.
The built-in OMU module is abnormal.The host OMU module is abnormal.The internal network adapter of the OMU board is fa
The E1/T1 cable is not properly connected to the interface board or is faulty.<p>The transmission equipment or transmission li
The data configuration of the E1/T1 port is inconsistent with the data configuration of the port of the peer NE.The transmission
The E1 frame formats configured at the BSC and the peer NE are inconsistent. For example, the BSC is configured with an E1
The link from the peer NE to the transmission equipment is faulty.<p>The link between the transmission equipment is faulty.</p
In E1 mode, the frame format is set to "E1_CRC4_MULTI_FRAME" at the local end whereas that is set to "E1_DOUBLE_FRA
The E1/T1 port of the local equipment is in a certain loopback mode, such as payload loopback, remote loopback, local loopba
The link code of the port of the BSC interface board is different from that of the port of the interface board of the peer NE.<p>T
The configuration of the clock source of the BSC is inconsistent with that of the peer equipment.The transmission equipment o
Remote loopback is set at the peer end.<p>Physical loopback is set.</p>
Local loopback is set at the local end.<p>Physical loopback is set.</p><p>Remote loopback is set at the peer end.</p><p>Loc
The optical cable is not securely inserted at the local end.<p>The optical port at the local end is faulty.</p><p>The transmissio
The optical cable is not securely inserted.<p>The TNU board at local end is faulty.</p><p>The transmission equipment is fault
The optical cable is not securely inserted.<p>The type of the optical cable is incorrect.</p><p>The optical port at the local end
The optical cable is not securely inserted.<p>The type of the optical cable is incorrect.</p><p>The optical port at the local end
The link at the peer equipment is not configured.The RX link of the local equipment is broken.<p>The optical cable is faulty.</p
The transmission line is in bad quality.
The settings of the signal label field of the [FILE]link1890[/FILE] byte at both ends are inconsistent.
The J2 byte format configuration is incorrect.
The peer equipment receives a low-order path alarm indication signal.<p>The peer equipment may have the Signal Label Mism
The peer equipment receives a low-order path alarm indication signal.The peer equipment may have the Low Order Path Une
The signal label field of the V5 byte at the peer end is set to 0.
The signal label byte (C2 byte) of the high-order path at the peer equipment is inconsistent with that at the local end.
The peer equipment sets the signal label byte C2 on the high-order path to 0.
The [FILE]link1893[/FILE] expected by the local end is inconsistent with the one sent by the peer NE.
The board is faulty.The optical port of the local equipment is manually set to a loopback mode.
The transmission equipment is faulty.The optical module is faulty.The peer equipment has no signal output to the transmission
The [FILE]link1892[/FILE] set at the peer end for transmission is inconsistent with the one expected by the local end.
The SDH/SONET RS Trace Identifier (J0) sent by the peer equipment is unstable.The length mode of the J0 byte configured a
The transmission equipment is faulty.The optical module is faulty.The peer equipment has no signal output to the transmission
The transmission line is in bad state.
The optical port at the local end is faulty.The optical port at the peer end is faulty.The service configuration of the transmission
The high-order path of the peer equipment has the following alarms: Administrative Unit Alarm Indication, Higher Order Path T
The high order path trace identifier (J1) sent by the peer equipment is unstable.The length mode of the J1 byte configured at th
The frame formats of the local and peer equipment are inconsistent.The interface board at the local end is faulty.The transmiss
The peer equipment has no signal output to the transmission equipment.The transmission equipment is faulty.
The optical port at the local end is faulty.The configuration of optical port at the local end and peer end is inconsistentThe optic
The low-order path signal label field sent by the peer equipment is unstable.
The [FILE]link1894[/FILE] sent by the peer end is unstable.The length modes of the J2 byte set at the local end and peer end
The receive link is faulty.<p>The transmission is faulty.</p><p>The link at the peer end is not configured.</p>
The optical port of the local board is faulty.The transmission quality of the transmission network is poor.
The optical port of the local board is faulty.The transmission quality of the transmission network is poor.
The clocks of the equipment at both ends of the tributary are not synchronized.
The optical module is faulty.
The E1 frame formats configured at the BSC and the peer NE are inconsistent. For example, the BSC is configured with the E
The link from the peer NE to the transmission equipment is faulty.<p>The link between transmission equipment is faulty.</p>Th
The tributary of the local equipment is configured as E1 CRC4 multiframe whereas the frame format of this tributary at the pee
The tributary of the local equipment is manually set to any optical port loopback mode.
The optical module does not match the optical port.
The clock source of the local BSC is inconsistent with that of the peer equipment.The optical cable is connected improperly.<p
An optical fiber is insecurely connected. The optical port at the local end cannot receive signals properly. The optical port at the
The chip of the optical port is faulty.
The configurations at the two ends of the TU are inconsistent.An optical port on the BSC board is faulty. <p>An optical port at
The SS bit of the V1 byte configured on a BSC board differs from that at the peer end.An optical port on a BSC board is faulty.
The peer end is the uni-end switchover modes, or the MSP function fail to be activated at the peer end.The working channel a
The protection modes at both ends of the MSP multiplex section are different, for example, 1:1 protection mode at one end an
The uni-end/bi-end switchover modes at both ends of the MSP multiplex section are different, for example, 1+1 uni-end switch
The [MML]DEA MSP[/MML] command has been run to deactivate the MSP.
The local IP address, peer IP address, and DSCP of an IP path configured at the peer end are inconsistent with those of the IP
The physical transmission link encounters transmission delay or packet loss, and the ratio of the actual traffic bandwidth to the
The corresponding PPP/MLPPP link is not configured at the peer end.<p>The PPP/MLPPP links are incorrectly configured. Fo
The configuration of MLPPP group or MLPPP links at the local end and peer end is not consistent, or MLPPP group or MLPPP
Negotiation fails between the local and peer ports because of inconsistency in the work mode or rate configured for both ports
The peer IP address is not configured or is deleted.<p>The configurations of VLAN ID are inconsistent between the local end
Conflicting IP addresses exist on the network.
The rates on the ports involved in load sharing are inconsistent, or not all the ports involved in load sharing work in the same d
All the links within the local trunk group are faulty.<p>The trunk group at the peer end is configured incorrectly or is removed.<
The configuration of the link within the trunk group is not correct. For example, the link within trunk group at the local end is no
The equipment at the peer end is congested.<p>The transmission link is in congestion, or packets are lost or delayed for a lon
Certain MP links in the MP group cannot take effect due to hardware limitations.
The local IP address is not configured with a route to the peer device.Internal problem at the peer endPeer end option not sup
The system is set to use Y line mode on the optical port in configuration data but actually it does not support this function beca
The parameter ETHOAM 3AH of the local BSC is configured incorrectly.The parameter ETHOAM 3AH of the peer NE is config
The loopback is enable at the local end and the local BSC successfully negotiates with the peer NE.<p>The loopback is enabl
The configuration of the peer NE is incorrect.The physical cable connection is faulty.
"Ater Link No. Sent from the Peer End" is inconsistent with "Expected Ater Link No.".<p>"BSC ID Sent from the Peer End" is in
The data configuration of the Gb interface is incorrect.The BC is blocked.The hardware of the Gb interface is faulty.The Gb inte
The backup channel is faulty.
A network storm occurs on the network. The network storm can be caused by a loopback, a faulty network adapter, improper c
The IP address, port number, and route configured for the link at the local end are inconsistent with those at the peer end.<p>T
The local equipment works improperly.<p>The peer equipment works improperly.</p><p>The transmission cable is subject to
The local equipment works improperly.<p>The peer equipment works improperly.</p><p>The transmission cable is subject to
The system is attacked by Address Resolution Protocol (ARP).
The transmission network is faulty. <p> </p>
The transmission network is faulty.
The transmission network is congested.
The mode of optical fibers do not match that of the connected optical module. As a result, the transmit optical power or receive
The number of IPMUX pipes configured for an interface board exceeds the maximum specification of the board.
GE port autonegotiation mode is configured for the local end, and FE port fixed mode is configured for the peer end.FE port au
The active and standby gateways are used when the BSC is configured with a policy-based routing based on a source IP addr
Fiber optical cable interconnection error.
The signaling link mask of the link set is inappropriately set.The bandwidth configured for the signaling link is insufficient.
The signaling route mask of the SP is inappropriately set.The signaling link mask of the link set is inappropriately set.The band
The MTP3 route to this DSP is not configured.All links to this DSP are faulty or deactivated.The DSP status on all signaling pro
The MTP3 link set is unavailable.The RNC receives a TFP message from the peer end.The MTP3 signaling route status on all
The link set has no MTP3 link configured.The MTP3 signaling link set status on all signaling processing subsystems is inconsi
The test of the signaling links fails.The signaling links are deactivated.The local management is prohibited, and the link is unav
This alarm may be generated on the Abis interface due to:Low congestion start thresholdInappropriate Abis timeslot multiplexin
The data configuration is erroneous.The interface board at the local end is faulty.The transmission device is faulty.The NE at th
The DSP of this SCCP subsystem is inaccessible. A local user inhibits the DSP.The peer SCCP data configuration is incorrect
Destination Signaling Point or Originating Signaling Point configuration is incorrect.Cell configuration is incorrect.Transmission
The data configuration of the link is erroneous.The transmission equipment is faulty.The link at the peer end is faulty.
For SCTP links whose application type is M3UA, the alarm cause may be the improperly configured signaling link mask of the
The data configuration of the link is erroneous.The transmission equipment is faulty.The link at the peer end is abnormal.
The M3UA link is prohibited or deactivated.The configuration of the M3UA route context is inappropriate.The bottom-layer SCT
The M3UA link set is unavailable.The RNC receives a DUNA message from the peer end.The M3UA route status on all signali
The configuration data at the two ends are inconsistent.The M3UA destination entity status on all signaling processing subsyst
The congestion left threshold is improperly set.An HW port is faulty.Boards are improperly installed, thus leading to a large am
The physical connection between two TNU boards in the two subracks is inconsistent with the data configuration.
The user blocks the IP address in the transmission resource pool by running the [MML]BLK IPPOOLIP[/MML] command.
Transmission resources are not configured.Transmission resources are faulty.Transmission resources are insufficient.
The path is faulty.The corresponding path has not been configured.The path configuration is incorrect.
1. The network element (NE) to which the link is connected is faulty.2. The transmission network is faulty.3. The link inside the
Transmission device configuration is incorrect or the transmission device status is abnormal. As a result, packet loss occurs or
The software running on the BBU or BCCH TRX board is faulty.The main control board or the BCCH TRX board is faulty.The B
A GSM cell is manually blocked.
Parameter values of this alarm are inappropriate.<p>When KPI Alarm Type is set to PS DPU Service Access Success Rate Ala
An incorrect bar code is configured in the BTS.The physical cable connection corresponding to the OML or RSL link is incorrec
The PCH queue overflows because a large number of paging messages are transmitted.
The transmission bandwidth of signaling links over the Ater interface is insufficient.
The configured binding between logical TRXs and local TRX groups is incorrect.The configured binding between a logical cell
The software on the BTS main control board is faulty.The hardware on the BTS main control board is faulty.All SCTP links ove
<p>The peer BSC is faulty.</p><p>The transmission on the detection link is interrupted.</p>
<p>The settings of BSC-level parameters related to BSC Node Redundancy are unsuited between two BSCs in a redundancy
Incorrect configuration dataThe software exception occurs, which causes a failure to make the configuration data on the servic
<p>SCTP link configurations conflict with each other.</p><p>Some SCTP links are configured but are not in use.</p><p>Som
The NSVC is blocked.The configuration of the BSC is inconsistent with that of the SGSN.The peer NE is faulty.
The configuration of the BSC is inconsistent with that of the SGSN.The IP communication between the BSC and the SGSN is
The NSE configured for the BSC is inconsistent with that for the SGSN.The Gb interface board is faulty.
The Gb interface parameter settings on the BSC and SGSN sides are inconsistent.The Gb interface is blocked on the BSC sid
The PTP BVC is blocked.The PTP BVC protocol procedure is abnormal.
The local maintenance end point (MEP) is not configured on the BSC.The sum of signaling or data weights at the local MEP is
The link configuration on the BSC side is inconsistent with that on the PCU side.The E1/T1 links on the Pb interface are faulty.
The initial PCIC configured on the BSC side is inconsistent with that configured on the PCU side.
The configuration of the BSC is inconsistent with that of the AC server.The AC server is faulty.The link between the BSC and th
The NRI values configured on the BSC are inconsistent with those on the corresponding MSC.The NRI values configured on t
The base station name configured on the eGBTS is different from that configured on the BSC.The BSC is not configured with
The traffic volume of smart services in the RNC exceeds the processing capability of the NIU board.
Data configuration The monitoring device is configured in a wrong cabinet/subrack/slot, or configured with a wrong serial port
Data configuration NoneSoftware NoneHardware The hardware of the monitoring device is faulty.Miscellaneous None
Data configuration NoneSoftware NoneHardware The sensor is faulty. The corresponding monitoring device is faulty. The c
Data configuration NoneSoftware NoneHardware The corresponding monitoring device is faulty. The power cable for the mo
Data configuration The alarm threshold setting is incorrect.Software NoneHardware The PSU is faulty. The corresponding m
Data configuration The alarm threshold setting is improper.Software NoneHardware The AC power network or the power dist
Data configuration NoneSoftware NoneHardware The power module is faulty. The solar array is faulty. The corresponding m
Data configuration NoneSoftware NoneHardware The power module is faulty. The corresponding monitoring device is faulty
Data configuration NoneSoftware NoneHardware The batteries are not installed. The power module is faulty. The batteries
Data configuration NoneSoftware NoneHardware The power module is faulty. The corresponding monitoring device is faulty
Data configuration NoneSoftware NoneHardware The AC surge protector fails. The corresponding monitoring device is fault
Data configuration NoneSoftware NoneHardware The power module is faulty. The monitoring module is faulty. The power m
Data configuration NoneSoftware NoneHardware The load fuse is broken or not in position.Miscellaneous None
Data configuration NoneSoftware NoneHardware The heater is faulty. The temperature sensor in the battery cabin is faulty.
Data configuration NoneSoftware NoneHardware The DSAC fails. The corresponding monitoring device is faulty. The comm
Data configuration The battery parameters are incorrectly set.Software NoneHardware The corresponding monitoring device
Data configuration NoneSoftware NoneHardware The lithium battery is faulty or its life is terminated. The circuit breaker on t
Data configuration NoneSoftware NoneHardware NoneMiscellaneous The number of configured power modules is insufficie
Data configuration The setting of the alarm threshold is improper.Software NoneHardware The temperature sensor malfuncti
Data configuration The setting of the alarm threshold is improper.Software NoneHardware The ambient humidity in the equip
Data configuration The setting of the alarm threshold is improper.Software NoneHardware The heat dissipation system of the
Data configuration The setting of the alarm threshold is improper.Software NoneHardware The heat dissipation system of the
Data configuration The setting of the alarm threshold is improper.Software NoneHardware The heater in the battery cabin is
Data configuration The setting of the alarm threshold is improper.Software NoneHardware The heat dissipation system of the
Data configuration NoneSoftware NoneHardware The heat dissipation system of the cabinet malfunctions. The sensor is fau
Data configuration NoneSoftware NoneHardware The TEC module group is faulty. The corresponding monitoring device is f
Data configuration NoneSoftware NoneHardware The heater hardware is faulty.Miscellaneous None
Data configuration The alarm function of the water alarm is configured incorrectly.Software NoneHardware The water sensor
Data configuration The alarm function of the smoke alarm is configured incorrectly.Software NoneHardware The smoke sens
Data configuration The function of the door status or infrared alarm is configured incorrectly.Software NoneHardware The se
Data configuration NoneSoftware NoneHardware The fan is worn-out. The corresponding monitoring device is faulty. The c
Data configuration NoneSoftware NoneHardware The sensor is faulty. The corresponding monitoring device is faulty. The a
Data configuration NoneSoftware NoneHardware The diesel generator is faulty. The corresponding monitoring device is fau
Data configuration NoneSoftware NoneHardware The monitoring device is faulty. The solar array is lost. The loop of the sol
Data configuration NoneSoftware NoneHardware The PSU is short-circuited or disconnected. The corresponding monitoring
Data configuration The setting of the alarm threshold is improper.Software NoneHardware The temperature sensor is faulty.
Data configuration Data configuration of a CCU is incorrect.Software NoneHardware The inter-CCU cables are incorrectly co
Data configuration NoneSoftware NoneHardware Inter-CCU ports of the same type are connected. A ring network is set up
Data configuration NoneSoftware NoneHardware The interface board, backplane, or main control board in the BBU is faulty.
Data configuration The E1/T1 link is incorrectly configured.Software NoneHardware The E1/T1 transmission link is faulty.Mis
Data configuration The E1/T1 link is incorrectly configured.Software NoneHardware The E1/T1 transmission link is faulty.Mis
Data configuration The E1/T1 link is configured incorrectly.Software NoneHardware The E1/T1 transmission link is faulty.Mis
Data configuration The E1/T1 link is incorrectly configured.Software NoneHardware The E1/T1 transmission link is faulty.Mis
Data configuration The E1/T1 link is incorrectly configured.Software NoneHardware The E1/T1 transmission link is faulty.Mis
Data configuration The E1/T1 configuration is incorrect, focus on checking the clock source master-slave relationship is consi
Data configuration The E1/T1 configuration is incorrect, focus on checking the clock source master-slave relationship is consi
Data configuration NoneSoftware The user sets the local or remote loopback on the E1/T1 link.Hardware The E1/T1 physica
Data configuration The parameter settings at both ends of the PPP/MLPPP link are inconsistent.Software NoneHardware No
Data configuration The parameter settings on the two ends of the MLPPP group are inconsistent.Software NoneHardware N
Data configuration The setting of the threshold is improper.Software NoneHardware NoneMiscellaneous The quality of the E
Data configuration The preset threshold is improper.Software NoneHardware NoneMiscellaneous The E1/T1 transmission p
Data configuration The alarm reporting threshold is not set properly.Software NoneHardware Loopback exists on the network
Data configuration The Ethernet port parameter settings of the Local NE are inconsistent with those of the Neighbor NE . The
Data configuration The parameter settings of the local Ethernet port are inconsistent with those of the peer Ethernet port.Softw
Data configuration The settings of the local Ethernet port are incorrect. The settings of the peer Ethernet port are incorrect. T
Data configuration The IP address of the device is incorrectly configured. The IP address of the external device is incorrectly
Data configuration The parameters configured for the local device are inconsistent with the parameters configured for the pee
Data configuration The local BFD session configuration is incorrect. The local route configuration is incorrect. The peer devic
Data configuration NoneSoftware NoneHardware The local transmission port is faulty.Miscellaneous The peer device is faul
Data configuration NoneSoftware NoneHardware NoneMiscellaneous The base station is under the flood attack. The base
Data configuration NoneSoftware NoneHardware The hardware of the control board is faulty. The BBU hardware is faulty. T
Data configuration NoneSoftware NoneHardware The temperature sensor for the board is faulty. The fans are stalled. The f
Data configuration NoneSoftware NoneHardware The board hardware is faulty. The hardware of the main control board is fa
Data configuration NoneSoftware NoneHardware The power monitoring board is faulty. The board hardware is faulty.Miscell
Data configuration NoneSoftware NoneHardware The BBU fan is faulty. There are foreign objects in the BBU fan.Miscellane
Data configuration NoneSoftware NoneHardware The BBU fan is faulty. There are foreign objects in the BBU fan.Miscellane
Data configuration NoneSoftware NoneHardware The power module of the BBU is faulty. The power module is not switched
Data configuration NoneSoftware NoneHardware The power module of the BBU is faulty.Miscellaneous The AC mains or th
Data configuration NoneSoftware NoneHardware The hardware of the GPS satellite card is faulty.Miscellaneous None
Data configuration NoneSoftware NoneHardware The GPS surge protector is faulty. The GPS satellite card hardware is fau
Data configuration The working mode of the GPS satellite card is incorrectly configured. The configured antenna angle is too
Data configuration NoneSoftware The software of the GPS satellite card is running improperly.Hardware The cable between
Data configuration NoneSoftware NoneHardware The board hardware is faulty.Miscellaneous The board temperature is out
Data configuration Too many configuration or maintenance operations are performed on the board.Software Too many test, tr
Data configuration NoneSoftware An error occurs on the program running on the board.Hardware The board hardware is fau
Data configuration NoneSoftware NoneHardware The board hardware is faulty. The backplane slot is faulty. The hardware
Data configuration A board supporting only one mode is configured for different modes.Software The board file system is bein
Data configuration The actual slot of the main control board is inconsistent with its configured slot. The main control board is
Data configuration NoneSoftware NoneHardware NoneMiscellaneous The user runs a command to block the board.
Data configuration NoneSoftware The inter-board CANBUS communication is abnormal.Hardware The Power Module DC ou
Data configuration NoneSoftware The file system in the transmit board is being formatted due to errors. The transmit board a
Data configuration NoneSoftware NoneHardware The backplane slot is faulty. The board hardware is faulty.Miscellaneous T
Data configuration NoneSoftware NoneHardware The optical module on the transmission port of the BBU is faulty.Miscellane
Data configuration Redundant transmission links are configured on the BBU.Software NoneHardware The optical module on
Data configuration NoneSoftware NoneHardware Optical module: The optical module on the transmission port of the BBU is
Data configuration NoneSoftware NoneHardware The optical port on the peer transmission device malfunctions.Miscellaneo
Data configuration NoneSoftware NoneHardware The optical module on the port of the BBU connecting to the lower-level RF
Data configuration A redundant RRU chain/ring is configured.Software NoneHardware The optical module on the port of the
Data configuration NoneSoftware NoneHardware The optical module on the port of the BBU connecting to the lower-level RF
Data configuration NoneSoftware NoneHardware The optical module on the port of the BBU connecting to the lower-level RF
Data configuration Data configuration is incorrect if a multi-mode base station reports the alarm. As a result, the timing loop fa
Data configuration When the dual-mode CPRI MUX topology is adopted, the aggregation configuration on one side conflicts w
Data configuration The RRU chain/ring configuration is incorrect.Software NoneHardware The number of RRU cascading lev
Data configuration A breakpoint is set in the RRU chain/ring.Software NoneHardware NoneMiscellaneous None
Data configuration The user configures the RRU chain topology, but the RRU ring topology is actually used. The user configu
Data configuration Data configuration is incorrect.Software NoneHardware The optical inter-BBU connections are incorrect.M
Data configuration The configuration data does not match hardware capabilities. In baseband extension mode, the TRX confi
Data configuration NoneSoftware NoneHardware The memory for storing software in the active workspace is faulty.Miscellan
Data configuration An incorrect board is configured.Software NoneHardware An incorrect board is installed in the slot.Miscel
Data configuration The board type has never been configured earlierSoftware The NE system file is damaged, and the NE co
Data configuration NoneSoftware The board software upgrade fails during the NE software upgrade. In this case, the board B
Data configuration NoneSoftware The current software version has problems.Hardware NoneMiscellaneous None
Data configuration The clock reference is not configured.Software NoneHardware The board hardware malfunctions.Miscella
Data configuration The clock reference is icorrectly configured.Software NoneHardware The hardware of the UTRP, USCU, o
Data configuration The IPCLK link is incorrectly configured. The route from the NE to the clock server is not configured.Softw
Data configuration NoneSoftware NoneHardware The main control board hardware is faulty. The clock reference malfunctio
Data configuration NoneSoftware The system clock phase-locked loop in the main control board is unlocked.Hardware The b
Data configuration NoneSoftware The base station in the other mode is repeatedly reset because the base station is not conf
Data configuration The parameter settings of a monitoring device in a mode are incorrect.Software NoneHardware NoneMis
Data configuration The working mode of an RF unit is incorrectly configured in one mode. The parameters of an RF unit in on
Data configuration The configuration of dry contacts for the UPEU/UEIU in a mode is inconsistent with that in the other mode.
Data configuration The cabinet/subrack/slot configuration of a board in one mode is incorrect. For a monitoring device, the cab
Data configuration In a multi-mode base station, the cabinet type of one mode is incorrectly configured.Software NoneHardw
Data configuration The clock reference type of a mode is incorrect. The DID of a mode is incorrect.Software NoneHardware
Data configuration The loading control rights are not configured after the multi-mode base station is deployed. The loading co
Data configuration The working mode of the RF unit is incorrectly configured in the system. The working mode configured for
Data configuration In a multi-mode base station, the cabinet/subrack number of a main control board of a mode is incorrectly
Data configuration NoneSoftware NoneHardware The optical module on an inter-BBU port is faulty.Miscellaneous None
Data configuration Data configuration is incorrect.Software NoneHardware The connecting piece on an inter-BBU port is fau
Data configuration NoneSoftware NoneHardware The optical module on an inter-BBU port is faulty. The UCIU is faulty. The
Data configuration NoneSoftware NoneHardware The optical module on an inter-BBU port deteriorates.Miscellaneous None
Data configuration NoneSoftware NoneHardware The hardware of the board is faulty. The optical module in the peer inter-B
Data configuration NoneSoftware NoneHardware NoneMiscellaneous Inter-BBU interfaces of the same type are connected,
Data configuration The networking of interconnection ports is incorrectly configured.Software NoneHardware The cable conn
Data configuration The configured subrack type is inconsistent with the actual subrack type.Software NoneHardware NoneM
Data configuration The networking of RF units is incorrect. Redundant lower-level RF units are configured.Software NoneHar
Data configuration NoneSoftware NoneHardware The type of the optical module installed on an RF unit is not supported by t
Data configuration NoneSoftware NoneHardware The optical module or connector of the current-level RF unit is improperly i
Data configuration NoneSoftware NoneHardware If the optical transmission is used, the optical module or connector of the R
Data configuration NoneSoftware NoneHardware The optical module or connector of the current-level RF unit is improperly i
Data configuration NoneSoftware NoneHardware The optical module or electrical module of the RF unit is faulty.Miscellaneo
Data configuration NoneSoftware The software used for power control or adjustment has flaws.Hardware The hardware of th
Data configuration The setting of attenuation of the RX channel is incorrect.Software NoneHardware The TMA is faulty. The
Data configuration The setting of attenuation on the RX channel of the RF unit is incorrect.Software NoneHardware The mai
Data configuration NoneSoftware NoneHardware The hardware of the RF unit is faulty.Miscellaneous None
Data configuration NoneSoftware NoneHardware The hardware of the RF unit is faulty.Miscellaneous The ambient tempera
Data configuration The user access threshold is improper, which leads to the actual number of users to exceed the allowed ca
Data configuration The preset VSWR threshold is very low. It is recommended that the VSWR alarm threshold not be used as
Data configuration The preset ALD current threshold of the RF unit is incorrect.Software NoneHardware The feeder connecto
Data configuration The coaxial ALD switch is configured, but actually the multi-wire cable is connected to the multi-wire port. T
Data configuration NoneSoftware NoneHardware The RF unit hardware is faulty.Miscellaneous None
Data configuration NoneSoftware The software program of the RF unit runs improperly, such as suspension.Hardware A soft
Data configuration The user runs too many configuration or maintenance commands frequently on the RF unit. The user star
Data configuration NoneSoftware NoneHardware The uplink interface of the RF unit is faulty, resulting in the faulty clock that
Data configuration NoneSoftware NoneHardware NoneMiscellaneous The AC power supply to the RF unit fails.
Data configuration the configured ALD switch does not match the actual type of the ALD port on the RF unit. The ALD switch
Data configuration The backup power device is configured, but not required actually.Software NoneHardware The backup po
Data configuration The serial port device is configured, but not installed actually.Software NoneHardware The serial port dev
Data configuration NoneSoftware NoneHardware The RF unit encounters lightning strikes. Therefore, open-circuit protection
Data configuration The command is executed to turn off the switch of the TX channel of the RF unit.Software NoneHardware
Data configuration NoneSoftware NoneHardware The PSU is faulty. The cabinet type and the RF unit type mismatch.Miscel
Data configuration NoneSoftware The ALD current of the RF unit is abnormal. The feeder installation is improper. For examp
Data configuration NoneSoftware NoneHardware The motor of the RET antenna is faulty.Miscellaneous None
Data configuration NoneSoftware NoneHardware The antenna device (RET antenna or TMA) hardware is faulty.Miscellaneo
Data configuration NoneSoftware NoneHardware A newly installed RET antenna is not calibrated. The RET antenna is powe
Data configuration NoneSoftware The RET antenna is powered off during data reconfiguration, which leads to data loss.Hard
Data configuration NoneSoftware NoneHardware The TMA hardware is faulty.Miscellaneous None
Data configuration The configured downtilt exceeds the antenna capability.Software NoneHardware The RET antenna works
Data configuration NoneSoftware The TMA works improperly, resulting in an automatic change of the TMA gain or TMA work
Data configuration NoneSoftware NoneHardware NoneMiscellaneous The peer certificate is not updated in time, and the pe
Data configuration The time of the base station is incorrectly set. The license expiry time is incorrectly configured.Software N
Data configuration NoneSoftware NoneHardware NoneMiscellaneous The certificate expires or is revoked. The certificate f
Data configuration The task used to automatically update the certificate is not configured according to the configuration plan,
Data configuration The preset ALD current threshold of the GATM is incorrect.Software NoneHardware The ALD power supp
Data configuration NoneSoftware NoneHardware NoneMiscellaneous The mains supply is unavailable. The power cable be
Data configuration The main control board version does not match the TRX version. When the dual-mode CPRI MUX topolog
Data configuration NoneSoftware NoneHardware NoneMiscellaneous The TRX or cell is blocked on the SMT without obtain
Data configuration When the specific problem is Release Abnormal, Activation Abnormal, or No Traffic on TRX, the cause is 'I
Data configuration The data configuration is incorrect.Software The module software is faulty.Hardware The uplink or downlin
Data configuration Users perform fast and dynamic configurations on a large number of TRXs in batches at a site. User confi
Data configuration NoneSoftware NoneHardware An RX channel of the RF unit is faulty. The RF cable on the main or divers
Data configuration The user configuration is incorrect.Software None.Hardware The jumper connection is incorrect. The jum
Data configuration The configuration is not correct.Software NoneHardware NoneMiscellaneous None
Data configuration The uplink IP route for the inactive link from the BTS to the BSC is not configured. The downlink IP route f
Data configuration The packet loss alarm threshold is set improperly.Software NoneHardware The bandwidth of the physical
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
The signal output from the external sensor reaches or exceeds the threshold.
n Frame (PDF).
perature is too high or too low, or the humidity is too high or too low. The specific cause of the alarm is determined by the type of the sensor
ter, low temperature in the equipment room, and high atmospheric pressure. The high humidity may be caused by high temperature, moist w
he equipment room, such as the air conditioner or fans, are faulty or stop operating.The ambient temperature increases the high temperatu
perature in the equipment room is too high. The air vents are blocked.
lane is lost. The alarm is generated on one or more SDH 8K Hz clock, SDH 19 MHz clock, TDM 8K Hz clock, or TDM 32 MHz clock.
ock reference source is abnormal (the frequency offset exceeds the pull-in range). The board is faulty.
The clock signal cables are faulty. The board is faulty.The input signal of the clock reference source is lost. The frequency offset of the input
ources are unavailable. In <b>Auto Handover</b> mode, the clock reference source of the highest priority switches between available and
k on the backplane is faulty. The No. 1 8 kHz clock on the backplane is faulty. The 8 kHz clock of the active GCU is faulty.The 8 kHz clock o
nals output from the selected clock reference source to the board are of bad quality.
rmal. The DSP cannot properly receive the synchronization time information.
of the input signal of the clock source is abnormal.
Gs is faulty.The clock signal cables are faulty.The input signals of the reference clock source are lost.The frequency offset for the input sign
Ethernet cables or fiber optic cables in a trunk group on an SCU in one subrack connect to different trunk groups in another subrack.The int
is not securely inserted. The backplane is faulty.The local board or the peer board is not securely inserted. The communication between th
is not securely inserted.The backplane is faulty.
erted.One Ethernet cable that connects the OMU to the GE port on the panel of the SCU board is not inserted, not securely inserted, or faul
securely connected. The Ethernet cable is faulty. The hardware of the peer board is faulty. The hardware of the local board is faulty.
or rate configured for both ports.The Ethernet cable is not connected or insecurely connected to the board panel or the Ethernet cable is fau
not securely connected, or faulty. The hardware of the active and standby boards at the peer end is faulty. The hardware of the active and st
e backplane, the GE link is faulty. The hardware of the board is faulty.The backplane is faulty.
board is not securely inserted.The backplane is faulty.The peer board is absent. The clock signals transmitted by the SCU board to the servi
faulty link is not installed or is reset.The cable between the panels of the local and peer TNU boards is faulty or not properly connected.The
faulty or not securely inserted.The local board is not securely inserted. The backplane is faulty.
vice board from the SCU are faulty.The local board is not securely inserted.The peer board that carries the faulty link is not in position or no
nk is reset.The cable between the TNU panels are not securely inserted.The cable between the TNU panels is faulty.Clock signals transmitt
ard is faulty and loops back the packets that are from other boards to itself to the GE switching board.
cal board are looped back to the local board.The DIP switch settings of subracks are conflicted.The cable connection between the main sub
software faults.The system inhibits the faulty board.The board is not installed.The board resets due to hardware faults.The board fails due t
The GE link inside the board is faulty.The GPS card is faulty.The clock component is faulty.The temperature sensor is faulty.At least two DSP
is received, but a switchover between the active/standby SCU boards cannot be performed.
board does not work normally.
urn off.Flow control threshold of the board is configured too high.The CPU load of the subsystem exceeds the configured threshold.
k source signal from the GCU/GCG board is abnormal.The source 1PPS signal from the clock board is abnormal.The external environment
tion exceeds the overload threshold.
SCU board or the service board is not properly installed.The service board has a hardware fault.The backplane has a hardware fault.
active or standby OMU is faulty.The hard disk space of the active or standby OMU is insufficient. The link between the active and standby
OMU during the version upgrade or the version rollback process.The software version installed on the active OMU is inconsistent with the
ated.The debug network adapter (ETH2) of the OMU is connected to the same network with either of the external network adapters (ETH0
bsc/weblmt logical disk is less than 300 MB or the remaining space of other OMU logical disks is less than 450 MB.
ommunication link between active The SNTP server is configured incorrectly. The network connection between the OMU and SNTP server i
MU is abnormal.The OMU works abnormally.
twork adapter is inconsistent with the expected duplex mode. Run the [MML]LST DUPLEX[/MML] command to query the actual and expecte
f the virtual IP address of the internal network is incorrect.The subnet masks of the backup channel IP addresses of the active and standby
nconsistent with that configured on the standby OMU board.The VLAN ID configured on the active OMU board for communication with the V
rating system upgrades or switchovers.Hard disk faults (such as SMART errors) cause file loss.OMU files are deleted or modified by mistak
that recorded in the version description file of the OMU. The inconsistency may be caused by the fact that the host fails to load the latest so
ccurs during license activation.
ndex 0) corresponding to the ESN does not process any services within 24 hours.</p><p>The version of the license file is inconsistent with
at for the EMS.The network communication between the NE and EMS is faulty.
The Convert Management System is stopped. The alarm box in the Convert Management System is disconnected.
IVE[/MML] command is executed. Data is restored from the data backup file which contains data of subracks in ineffective mode.The syste
000.The U2000 managing the BSC was replaced with a new U2000 and the new U2000 has not delivered information of GBTS licenses to t
while the local BSC stays.
s a result, the switching capability on the board is insufficient, and therefore cannot provide services for all TRXs. The number of CICs confi
nfigured.The network between the OMU and the CA is faulty.The configured CA or CRL server fails to work properly.The network between t
ot update the certificate in time,but the user still uses this certificate to log in to the OMU. The digital certificate at the peer end does not com
adapter (ETH2) of the SAU is connected to the same network with either of the external network adapters (ETH0 and ETH1), this alarm is g
mode of the SAU Ethernet adapter.The hard disk of the SAU is faulty. The array card of the SAU is faulty. The Ethernet adapter of the SAU
nication between the OMU and SCU boards fails.The SCU board is faulty.
teway IP address of the default route cannot be pinged through.</p>The external network of the standby OMU is abnormal.
adapter of the OMU board is faulty.Communication between the OMU and SCU boards fails.The SCU board is faulty.
on equipment or transmission link between the interface board and the peer NE is faulty.</p><p>The interface board is faulty.</p><p>The b
f the peer NE.The transmission equipment or transmission link with the peer NE is faulty.<p>The interface board is faulty.</p>The clock at th
he BSC is configured with an E1 dual-frame whereas the peer NE is configured with an E1 CRC4 multi-frame.The transmit link of the BSC is
smission equipment is faulty.</p>The peer NE is faulty or has been reset.<p>The transmission equipment is faulty or has been reset.</p><p
at is set to "E1_DOUBLE_FRAME" at the peer end. The transmission quality is poor or the transmission equipment is faulty.
, remote loopback, local loopback, or single channel loopback.
ace board of the peer NE.<p>The E1/T1 impedance configured for the BSC interface board or peer NE interface board is inconsistent with
.The transmission equipment or transmission link between the BSC and the peer equipment is faulty.
set at the peer end.</p><p>Local loopback of the optical port tributary is set at the transmission equipment.</p>
s faulty.</p><p>The transmission link is faulty or is not correctly connected.</p><p>The transmission equipment is faulty.</p><p>The peer e
transmission equipment is faulty.</p><p>The optical port at the peer end is faulty.</p><p>The receiving circuit of the local equipment is nor
The optical port at the local end is faulty.</p><p>The transmission equipment is faulty.</p><p>The optical port at the peer end is faulty.</p>
The optical port at the local end is faulty.</p><p>The transmission equipment is faulty.</p><p>The optical port at the peer end is faulty.</p>
p>The optical cable is faulty.</p>The transmission link is in bad quality.
may have the Signal Label Mismatch alarm or Low Order Path Unequipped alarm.</p><p>Bit errors exist at the RX end of the low-order pa
have the Low Order Path Unequipped or Signal Label Mismatch alarm.Bit errors exist at the RX end of the low-order path of the peer equip
he BSC is configured with the E1 dual-frame but the peer NE is configured with the E1 CRC4 multi-frame.The transmit link of the BSC is fau
ssion equipment is faulty.</p>The peer NE is faulty or has been reset.<p>The transmission equipment is faulty or has been reset.</p><p>A
rmat of this tributary at the peer equipment is different.The tributary of the local equipment is configured as T1 superframe whereas the fram
is faulty. <p>An optical port at the peer end is faulty. </p><p>The transmission link is faulty. </p><p>The transmission device is faulty.</p>B
al port on a BSC board is faulty. <p>An optical port at the peer end is faulty. </p><p>The transmission link is faulty. </p><p>The transmissio
eer end.The working channel at the local end is connected to [FILE]link1907[/FILE] at the peer end, or the protection channel at the local en
protection mode at one end and 1+1 protection mode at the other end. That is, bit 5 of the received K2 byte is inconsistent with the expecte
or example, 1+1 uni-end switchover mode at one end and 1+1 bi-end switchover mode at the other end. That is, the last three bits of the rec
inconsistent with those of the IP path configured at the local end.The IP PM protocols at the local and peer ends are incompatible with each
e actual traffic bandwidth to the actual logic port bandwidth reaches or exceeds 60% for five consecutive seconds.
ks are incorrectly configured. For example, the E1/T1 timeslots of the PPP/MLPPP links at the local end are different from those at the peer
ent, or MLPPP group or MLPPP links at peer end is not configured.All the E1/T1 cables or optical cables that carry the MLPPP links in the M
or rate configured for both ports.The physical connection of the Ethernet port is faulty.The peer equipment is faulty.The sub-board of the boa
nsistent between the local end and the transmission equipment.</p><p>If the detection type is BFD, the BFD configuration for the peer equ
eer endPeer end option not supportedInsufficient resources for the peer endNo response from the peer endTCP connection not set up
s not support this function because of CPLD version.The version of the backplane is too early, so TDM transmission can not be configured
M 3AH of the peer NE is configured incorrectly.The FG2a/GOUa/FG2d/FG2c/GOUd/GOUc/GOUe is faulty.The link of the FG2a/GOUa/FG2
r NE.<p>The loopback is enabled at the peer end and the peer NE successfully negotiates with the local BSC.</p>
D Sent from the Peer End" is inconsistent with "Expected BSC ID".</p><p>The transmission cable is incorrectly connected (In this case, th
lty network adapter, improper cable connections, or broadcast packets-generating application programs or protocols (such as network virus
with those at the peer end.<p>The link is not configured at the local end.</p><p>There are viruses or hacker attacks on the network.</p>
ansmission cable is subject to severe interference or be aging.</p><p>The intermediate transmission equipment works improperly.</p>
ansmission cable is subject to severe interference or be aging.</p><p>The intermediate transmission equipment works improperly.</p>
ansmit optical power or receive optical power of the optical module is higher than the maximum value.The optical connectors are dirty. As a
ion of the board.
ured for the peer end.FE port autonegotiation mode is configured for the local end, and 10 Mbit/s fixed mode or half-duplex mode is configur
uting based on a source IP address. The interconnected router is configured with two routes that have different priorities. However, the prior
prohibited, and the link is unavailable.Receive the COO(changeover-order) signal from the peer end.The remote management is prohibited
ropriate Abis timeslot multiplexing mode on the BTS (Multiplexing Mode)This alarm may be generated on the Ater interface due to:Low cong
ion device is faulty.The NE at the peer end is faulty.
data configuration is incorrect or the peer SCCP is abnormal. For example, the SCCP subsystem number parameter at the peer end is not
ration is incorrect.Transmission or the peer end is faulty.
lower than the congestion left bandwidth threshold (forward bandwidth or backward bandwidth).
onfigured bandwidth (forward bandwidth or backward bandwidth).The bandwidth available over the port (forward bandwidth or backward ba
ceeds the configured bandwidth (forward bandwidth or backward bandwidth).The bandwidth available for the resource group (forward bandw
eds the configured bandwidth (forward bandwidth or backward bandwidth).The bandwidth available for the IP logical port (forward bandwid
s faulty.The BTS reports that the HDLC is in faulty state.
ne-Way Mute Detection Threshold[/PARMNAME] is excessively small. The CIC configuration on the BSC is inconsistent with that on the co
lled, thus leading to a large amount of inter-subrack services. The amount of resources configured for inter-subrack connection is too small.
data configuration.
POOLIP[/MML] command.
ources are insufficient.
k is faulty.3. The link inside the base station controller is faulty.Virus or hacker attack exists on the network.
s a result, packet loss occurs or the delay increases. The peer device configuration is incorrect or the peer device status is abnormal.
BCCH TRX board is faulty.The BBU or the optical module of the BCCH TRX board is faulty.The CPRI optical fiber between the BBU and the
ransmission equipment or transmission link between the BSC and the BTS is faulty.There is no power supply to the BTS.
Flex Abis.The BTS is set to support physical/logical separation in configuration data but actually the BTS does not support physical/logical
nsistent with the physical connection. (2) The bar code configuration of the main control board is inconsistent with the actual configuration w
wing symptoms: Setting up a link fails. There are no broadcast messages from the cell broadcast center (CBC) for a long period of time. The
d or TRX board of the BTS is faulty.The software running on the Abis, Ater or A interface board is faulty.The cable connections between TNU
aulty. The TRX board is faulty.There is a high probability that the bit error rate (BER) on the Abis interface is high.
ervice Access Success Rate Alarm, the DPU board whose logical function type is GPCU has hardware faults.</p><p>When KPI Alarm Type
the OML or RSL link is incorrect.
een two BSCs in a redundancy group. </p><p>The settings of dual-homed BTS-level parameters are unsuited between two BSCs in a redu
configuration data on the service processing module of the board take effect.
but are not in use.</p><p>Some ABISCP resources are configured but are not in use.</p><p>Other causes.</p>
eer NE is faulty.
een the BSC and the SGSN is interrupted.
rface is blocked on the BSC side.The Gb interface is blocked on the SGSN side.DSP resources are insufficient.The DPU board is not config
data weights at the local MEP is 0. The number of the local MEPs exceeds eight.The server IP address or User Datagram Protocol (UDP) po
s on the Pb interface are faulty.The interface board of the BSC or the interface board of the PCU is faulty.The PCU is faulty.The signaling lin
The BSC is not configured with the base station whose name is to be matched.
igured with a wrong serial port or communication address.Software NoneHardware The monitoring device is faulty. The interface board, b
ulty.Miscellaneous None
onitoring device is faulty. The cable connection of the sensor is faulty.Miscellaneous None
lty. The power cable for the monitoring device is faulty. For example, the power cable is loosely connected, worn-out, or damage. The upp
is faulty. The corresponding monitoring device is faulty.Miscellaneous The battery charge is insufficient. The AC input is out of range.
power network or the power distribution is faulty. The monitoring device is faulty. The AC circuit breaker is switched off. The AC input powe
y is faulty. The corresponding monitoring device is faulty. The solar array fails to provide the DC output.Miscellaneous The AC input is out
ding monitoring device is faulty. The batteries are powered off manually.Miscellaneous The mains input is out of range. The batteries are
module is faulty. The batteries are faulty or worn out. The corresponding monitoring device is faulty. The circuit breaker is turned off and th
ding monitoring device is faulty.Miscellaneous The cabinet is overheated. The mains input is out of range.
nding monitoring device is faulty. The cable connection between the AC surge protector and the monitoring device is loose or broken, or th
g module is faulty. The power module is not secure or not in position. The monitoring module is not securely installed.Miscellaneous None
iscellaneous None
or in the battery cabin is faulty. The AC input power cable of the heater is not properly connected.Miscellaneous None
oring device is faulty. The communication cable between the DSAC and the monitoring device fails.Miscellaneous None
orresponding monitoring device is faulty. The batteries are not installed or the cable connections are abnormal. The circuit breaker of the b
inated. The circuit breaker on the lithium battery is switched off.Miscellaneous None
ured power modules is insufficient and N+1 backup of power modules cannot be achieved.
e temperature sensor malfunctions. The corresponding monitoring device is faulty. The cable connection is faulty.Miscellaneous The amb
e ambient humidity in the equipment room is abnormal. The humidity sensor malfunctions. The cable connection is faulty.Miscellaneous T
e heat dissipation system of the cabinet is faulty. The sensor is faulty. The monitoring device is faulty. The cable connection of the sensor
e heat dissipation system of the cabinet is faulty. The sensor is faulty. The monitoring device is faulty. The cable connection of the sensor
e heater in the battery cabin is faulty. The battery temperature sensor is faulty. The corresponding monitoring device is faulty. The cable c
e heat dissipation system of the cabinet is faulty. The sensor is faulty. The monitoring device is faulty. The air filter is blocked.Miscellaneou
malfunctions. The sensor is faulty. The monitoring device is faulty. The cable connection of the sensor is faulty.Miscellaneous The ambien
sponding monitoring device is faulty. The cable connection of the TEC is faulty.Miscellaneous None
neHardware The water sensor is faulty. The corresponding monitoring device is faulty. The cable connection between the water sensor an
oneHardware The smoke sensor is faulty. The corresponding monitoring device is faulty. The cable connection between the smoke senso
ftware NoneHardware The sensor is faulty. The corresponding monitoring device is faulty. The cable connection between the sensor and
onitoring device is faulty. The cable connection of the fan is faulty. The fan is blocked. The fan speed cannot be controlled.Miscellaneous
onitoring device is faulty. The alarm cable connection is faulty.Miscellaneous The fuel in the diesel generator is insufficient.
onding monitoring device is faulty. The diesel generator is shut down. The power cable that transmits the startup signals of the diesel gene
rray is lost. The loop of the solar array is broken, or the circuit breaker is switched off.Miscellaneous The solar array cannot receive any su
The corresponding monitoring device is faulty. The solar array is lost. The solar power supply unit is faulty.Miscellaneous The connection
e temperature sensor is faulty. The corresponding monitoring device is faulty. The cables of the temperature sensor are faulty.Miscellaneo
r-CCU cables are incorrectly connected.Miscellaneous None
ected. A ring network is set up after inter-CCU ports are connected.Miscellaneous None
ntrol board in the BBU is faulty. The BBU is not powered on or fails to be detected. The cable connections between the BBU and the mon
1 transmission link is faulty.Miscellaneous The local device is faulty. The E1/T1 transmission trunk is faulty. The peer device is faulty.
1 transmission link is faulty.Miscellaneous The local device is faulty. The peer device is faulty.
1 transmission link is faulty.Miscellaneous The local device is faulty. The E1/T1 transmission trunk is faulty. The peer device is faulty.
1 transmission link is faulty.Miscellaneous The local device is faulty. The E1/T1 transmission trunk is faulty. The peer device is faulty.
1 transmission link is faulty.Miscellaneous The local device is faulty. The E1/T1 transmission trunk is faulty. The peer device is faulty.
aster-slave relationship is consistent.Software NoneHardware NoneMiscellaneous The local clock of the NE malfunctions. The E1/T1 gro
aster-slave relationship is consistent.Software NoneHardware NoneMiscellaneous The local clock of the NE malfunctions. The E1/T1 gro
k.Hardware The E1/T1 physical loopback is performed.Miscellaneous None
hose of the Neighbor NE . The ETH OAM parameter settings of the local NE are inconsistent with those of the Peer NE.Software The ETH
e of the peer Ethernet port.Software NoneHardware The transmission performance of the Ethernet cable may be poor.Miscellaneous Non
er Ethernet port are incorrect. The ETHOAM 3AH settings are inconsistent with the network plan. The working modes of ETHOAM 3AH at
e external device is incorrectly configured.Software NoneHardware NoneMiscellaneous None
ameters configured for the peer device.Software NoneHardware NoneMiscellaneous The transmission link between the base station and
ion is incorrect. The peer device is faulty or its configuration is incorrect.Software NoneHardware NoneMiscellaneous The local transmiss
der the flood attack. The base station is under the invalid packet attack. The base station is under the ARP spoofing. The base station is u
The BBU hardware is faulty. The hardware of the board (non-control board) to which the alarm pertains to is faulty.Miscellaneous The boa
ulty. The fans are stalled. The fan board is not installed.Miscellaneous The ambient temperature of the subrack is extremely high or low.
e of the main control board is faulty. The subrack is faulty. The board is not securely installed. The main control board is not securely insta
board hardware is faulty.Miscellaneous Input Voltage Out of Range.
jects in the BBU fan.Miscellaneous None
jects in the BBU fan.Miscellaneous None
e power module is not switched on. The external power cable is faulty. The power consumption of all boards in the BBU exceeds the powe
cellaneous The AC mains or the power system malfunctions Note: BBU power failures lead to alarm reporting failures.
aulty.Miscellaneous None
S satellite card hardware is faulty. The signal cable between the BBU and the GPS surge protector is open-circuited or short-circuited. The
configured antenna angle is too large.Software NoneHardware The GPS antenna is faulty. Interference or barrier exists around the GPS a
.Hardware The cable between the RRU and RGPS is faulty. The cable between the BBU and RGPS is faulty. The GPS satellite card hard
actually used. The user configures the RRU ring topology, but the RRU chain topology is actually used. The topology configuration is consi
BU connections are incorrect.Miscellaneous None
extension mode, the TRX configuration exceeds the baseband capability. In baseband extension mode, the slot No. of the baseband board
ve workspace is faulty.Miscellaneous None
rd is installed in the slot.Miscellaneous None
file is damaged, and the NE communicates with the NMS improperly.Hardware NoneMiscellaneous The software to be supplemented is u
grade. In this case, the board BootROM upgrade fails.Hardware The available flash memory of the board is insufficient. The board hardwa
Miscellaneous None
hardware malfunctions.Miscellaneous The reference clock malfunctions.
hardware of the UTRP, USCU, or main control board is faulty.Miscellaneous If the clock reference is IPCLK, the IP clock link may fail. If the
k server is not configured.Software NoneHardware The port used for the IP clock link is faulty. The main control board or UTRP hardware
The clock reference malfunctions. The board hardware is faulty.Miscellaneous If this alarm is reported on a non-main control board, the b
rd is unlocked.Hardware The board hardware is faulty.Miscellaneous This board is not securely installed.
use the base station is not configured but the physical board is installed. The base station in the other mode is repeatedly reset because th
ware NoneHardware NoneMiscellaneous None
parameters of an RF unit in one mode are inconsistent with those of the same RF unit in the other mode.Software NoneHardware NoneM
ent with that in the other mode. The GPS configuration for the USCU in a mode is inconsistent with that in the other mode. The networking
For a monitoring device, the cabinet/subrack/slot configuration in one mode, cabinet/subrack number of the manager, serial port number, or
nfigured.Software NoneHardware NoneMiscellaneous None
rrect.Software NoneHardware NoneMiscellaneous None
on is deployed. The loading control rights are not configured after the main control board is replaced in the multi-mode base station. The lo
he working mode configured for the RF unit is not supported by the RF unit.Software NoneHardware The hardware model of the installed R
board of a mode is incorrectly configured.Software NoneHardware In a multi-mode base station, the installed position of a main control bo
faulty.Miscellaneous None
ece on an inter-BBU port is faulty. The cable for the optical module on an inter-BBU port is not installed or not connected securely. The cab
faulty. The UCIU is faulty. The peer board of an inter-BBU port is faulty.Miscellaneous The optical module on an inter-BBU port is not insta
teriorates.Miscellaneous None
ptical module in the peer inter-BBU port is faulty. The optical module in the local inter-BBU port is faulty.Miscellaneous The peer optical con
f the same type are connected, or a ring network is set up in the case of an inter-BBU connection.
NoneHardware The cable connecting the combined base stations is not connected. The cable connecting the combined base stations is n
ftware NoneHardware NoneMiscellaneous None
configured.Software NoneHardware The optical module on the port of the RF unit connecting to the peer device (upper- or lower-level RF
an RF unit is not supported by the RF unit. For example, an RF unit supports only an optical module of 2.5 Gbit/s, but an optical module of 1
ent-level RF unit is improperly installed, or the optical module is faulty. The optical connector of the current-level RF unit is dirty. The curren
al module or connector of the RF unit or peer device may be improperly installed, or the optical link is faulty. If the electrical transmission is
ent-level RF unit is improperly installed. Or the optical module is worn-out. The optical connector of the current-level RF unit is dirty. The o
he RF unit is faulty.Miscellaneous None
s.Hardware The hardware of the RF unit is faulty.Miscellaneous None
rdware The TMA is faulty. The feeder installation is improper. For example, the feeder connector is loose, soaked or damaged, or the feede
ware NoneHardware The main RX channel or diversity RX channel of the RF unit is faulty. The feeder connected to the RF unit is faulty, w
laneous None
laneous The ambient temperature of the RF unit is extremely high, or the heat dissipation malfunctions.
users to exceed the allowed capacity of the RF unit.Software NoneHardware NoneMiscellaneous The board in the BBU connected to the
alarm threshold not be used as the VSWR acceptance threshold. The VSWR threshold is set to an excessively low value for the other mod
Hardware The feeder connector is loose or waterlogged. The feeder is deformed. The jumper between the feeder and the antenna device
nnected to the multi-wire port. The multi-wire ALD switch is configured, but actually the multi-wire cable is not connected to the multi-wire po
as suspension.Hardware A soft failure occurs in the FPGA memory, which may affect the normal operation of an RAT.Miscellaneous None
y on the RF unit. The user starts too many test or measurement tasks on the RF unit.Software The software program of the RF unit runs im
resulting in the faulty clock that is extracted at the interface. The clock chip or another component in the RF unit is faulty.Miscellaneous No
to the RF unit fails.
n the RF unit. The ALD switch of the RF unit is not turned on. The data configuration of the antenna is incorrect. For example, the vendor c
NoneHardware The backup power device is not installed. The monitoring board of the backup power device is also not powered on or work
eHardware The serial port device is not powered on, or works improperly. The address settings of the DIP switch on the serial port device
herefore, open-circuit protection is implemented by in the power surge protector of the RF unit.Miscellaneous None
F unit.Software NoneHardware NoneMiscellaneous None
e RF unit type mismatch.Miscellaneous The abnormal mains supply leads to an insufficient battery voltage.
tallation is improper. For example, the feeder connector is soaked or damaged, or the feeder is deformed. The hardware of the RF unit is f
cellaneous None
hardware is faulty.Miscellaneous None
ated. The RET antenna is powered off when the antenna tilt is adjusted.Miscellaneous The configuration file of the RET antenna is downlo
n, which leads to data loss.Hardware The flash memory of the RET antenna is damaged. The RET antenna is newly installed without the d
dware The RET antenna works improperly, resulting in an automatic change of the downtilt.Miscellaneous Because of RET antenna reset o
e of the TMA gain or TMA work mode.Hardware NoneMiscellaneous Because of TMA reset or maintenance link disconnection, the data co
not updated in time, and the peer certificate expires or the peer certificate is revoked . An invalid user attempts to connect to the base stati
orrectly configured.Software NoneHardware NoneMiscellaneous Automatic certificate update fails. The certificate is about to expire. Tha
or is revoked. The certificate file is lost. The certificate file is damaged. The certificate file format is incorrect. The certificate has not taken
rding to the configuration plan, or the IP route is incorrectly configured.Software NoneHardware NoneMiscellaneous The transmission net
Hardware The ALD power supply circuit of the GATM is faulty. The antenna device is faulty.Miscellaneous The feeder connector is loose o
navailable. The power cable between the BTS and the power supply equipment is faulty.
e dual-mode CPRI MUX topology is adopted, the topology configuration is incorrect. A board is blocked.Software The software running on t
cked on the SMT without obtaining the site management rights.
o Traffic on TRX, the cause is 'Improper cell channel configuration.'Software When the specific problem is Activation Abnormal, the causes
Hardware The uplink or downlink channel on the module is faulty. The uplink or downlink path of the antenna is faulty. Engineering issues
in batches at a site. User configuration is incorrect. The configurations for the TRX frequency interval, power, number of TRXs, and bandw
RF cable on the main or diversity RX port of the RF unit is loose or damaged. Hardware connections of the antenna TX and RX modes on
onnection is incorrect. The jumper is faulty.Miscellaneous None.
gured. The downlink IP route for the inactive link from the BSC to the BTS is not configured. The route for boards (in other modes) carrying
The bandwidth of the physical link between the BTS and the BSC is restricted.Miscellaneous Bit errors or incorrect frame alarms occur on
increases the high temperature because of the board in the subrack. The air conditioner failure.
frequency offset of the input signal of the clock reference source is abnormal.The interface board from which the clock reference source is
tches between available and unavailable frequently and each available duration is shorter than 500 seconds.In manual handover mode, the
CU is faulty.The 8 kHz clock of the standby GCU is faulty.
uency offset for the input signals of the reference clock source is inappropriate.The clock signal cables are not connected securely.The statu
ps in another subrack.The inter-subrack connections are incorrect.Loopback exists on inter-subrack cable connections.
e communication between the local board and the peer board is faulty.
not securely inserted, or faulty.The Ethernet adapter connected to the SCU board in the OMU is prohibited.
lty link is not in position or not securely inserted.The local board is faulty.The peer board that carries the faulty link is faulty.The backplane is
faulty.Clock signals transmitted from the SCU board to the TNU board are inaccurate.The local board is faulty.The peer board that carries t
ection between the main subrack and the secondary subrack is incorrect.A board in another subrack sends packets with incorrect source M
re faults.The board fails due to the backplane faults, for example, pins are missing or broken.The board is reset by using the [MML]RST BR
nsor is faulty.At least two DSP components are faulty.The chip self-check is faulty.The flash component is faulty. The GE switching unit is fa
t be traced and the clock model is invalid; the satellite card trace satellites number is not enough (less than 4) over 24 hours; the satellite ca
configured threshold.
active OMU differs from that of the standby OMU.The network segment on which the backup channel IP address of the active and standby
n the OMU and SNTP server is abnormal. The SNTP server works abnormally. The authentication of the NTP encryption message fails.
query the actual and expected duplex modes of the OMU network adapter.If the hardware type is the hard disk or Raid, the hard disk or Ra
ses of the active and standby OMUs are incorrect.The network segment of the backup channel IP addresses of the active and standby OMU
d for communication with the VNP is inconsistent with that configured on the standby OMU board.
deleted or modified by mistake.There are external cyber attacks.There are computer viruses.Changes are made in files under monitoring wh
host fails to load the latest software version from the OMU because an error occurs during the version upgrade or cold patch installation.
cense file is inconsistent with the version of the system.</p><p>The system does not have an activated license file.</p><p>The license file i
Xs. The number of CICs configured on the Ater interface board using time division multiplexing (TDM) transmission exceeds the board spec
operly.The network between the CRL server and the OMU is faulty.
at the peer end does not comply with the X.509 standard. The signature of the digital certificate is invalid.The local CA certificate is invalid.
U is abnormal.
board is faulty.</p><p>The board of the peer NE is faulty.</p>The grounding with the peer equipment is abnormal.
rd is faulty.</p>The clock at the local end is faulty.<p>The clock of the peer NE is faulty.</p>
The transmit link of the BSC is faulty.<p>The transmit link from the BSC to the peer NE is faulty.</p> <p>The receive link of the peer NE is fa
aulty or has been reset.</p><p>A loopback has been performed on the peer NE. </p><p>A loopback has been performed from the transmis
pment is faulty.
ce board is inconsistent with that on the transmission medium.</p><p>The configuration of the clock source of the BSC is inconsistent with
nt is faulty.</p><p>The peer equipment is not in position.</p><p>The optical port at the peer end is faulty.</p><p>The optical cable is not se
of the local equipment is normal, but the transmitting circuit is faulty.</p><p>The transmission of the peer equipment is normal, but the rece
at the peer end is faulty.</p>
at the peer end is faulty.</p>
ismatch, Error Alarm Threshold Exceeded, Administrative Unit Signal Pointer Loss, and High Order Path Unequipped.
ransmit link of the BSC is faulty whereas the receive link of the BSC is functional. <p>The transmission link from the BSC to the peer NE is
or has been reset.</p><p>A loopback has been performed on the peer NE. </p><p>A loopback has been performed from the transmission
superframe whereas the frame format of this tributary at the peer equipment is different.The BER on the link is too high.
ection channel at the local end is connected to the working channel at the peer end. Thus, the number of the channel that the MSP multiple
inconsistent with the expected value. (Bit 5 of the K2 byte indicates the protection mode, with 0 indicating 1+1 protection mode and 1 indica
s, the last three bits of the received K2 byte is inconsistent with the last three bits of the K2 byte at the local end.
ds are incompatible with each other.The IP PM resources at the peer end are insufficient. <p>The transmission network is faulty, and therefo
ferent from those at the peer end.</p><p>The settings of the tributary numbering at both ends are inconsistent.</p>The E1/T1 cables or op
arry the MLPPP links in the MLPPP group are disconnected or faulty.
ulty.The sub-board of the board to which the Ethernet port belongs is faulty.The optical module is not inserted or is abnormal.The Ethernet p
configuration for the peer equipment is incorrect, or BFD negotiation fails.</p>If the intermediate transmission equipment, such as a switch a
ly connected (In this case, the BM/TC flag, BSC ID, or Ater link No. sent from the peer end is invalid). </p><p>The transmission equipment
cal connectors are dirty. As a result, the transmit optical power or receive optical power of the optical module is lower than the minimum val
ote management is prohibited, and the link is unavailable.No response from the peer end.Link released by peer end.No PDU received from
Ater interface due to:Low congestion start thresholdInsufficient LAPD linksThis alarm may be generated on the Pb interface due to:Low cong
ameter at the peer end is not configured, the values for configured SCCP subsystem number are inconsistent, or the board is overloaded.T
ink, or insufficient M3UA links.Transmission equipment is incorrectly configured or in the abnormal state so that packet loss occurs or delay
rd bandwidth or backward bandwidth) is equal to or lower than the congestion left bandwidth threshold (forward bandwidth or backward ban
esource group (forward bandwidth or backward bandwidth) is equal to or lower than the congestion left bandwidth threshold (forward bandw
logical port (forward bandwidth or backward bandwidth) is equal to or lower than the congestion left bandwidth threshold (forward bandwidt
consistent with that on the core network. If the port is an optical port, the optical port attributes configured on the BSC are inconsistent with
ce status is abnormal.
er between the BBU and the BCCH TRX board is faulty.The BSC interface board is faulty.The power supply to the BTS fails.The Abis trans
s not support physical/logical separation.The BTS is set to support Abis transmission optimization in configuration data but actually the BTS
with the actual configuration when automatic OML timeslot detection is enabled. BTS in IP transmission mode: (1) The configuration of the e
for a long period of time. The CBC requests link disconnection from the BSC. The BSC fails to send messages to the CBC.</p>The commu
ble connections between TNU boards in different subracks are incorrect.The cable connections for the Abis and Ater interfaces are incorrec
</p><p>When KPI Alarm Type is set to CS DPU Connectivity Success Rate Alarm, the DPU boards whose logical function type is GTC have
t.The DPU board is not configured on the BSC and therefore PS services cannot be provided.The Gb interface is faulty on the BSC side.A
r Datagram Protocol (UDP) port No. of the BSC is inconsistent with that of the SGSN.An exception occurs on the SGSN side.The Gb interfa
PCU is faulty.The signaling links on the PCU side are manually blocked.
faulty. The interface board, backplane, or main control board in the BBU is faulty. The monitoring device is not powered on or fails to be d
orn-out, or damage. The upper-level circuit breaker is turned on, or the fuse is disconnected or damaged.Miscellaneous The input power m
AC input is out of range.
ched off. The AC input power cable is faulty.Miscellaneous The PSU module cannot provide sufficient output power. As a result, the secon
laneous The AC input is out of range. The power supply capability of the PSU module is insufficient, leading to the battery discharging and
of range. The batteries are overheated.
uit breaker is turned off and the contactor is disconnected, or the cable for batteries is disconnected.Miscellaneous None
evice is loose or broken, or the connection between the surge protector and the subrack is insecure.Miscellaneous None
nstalled.Miscellaneous None
l. The circuit breaker of the battery cabinet is not switch on.Miscellaneous None
between the water sensor and the monitoring device is faulty.Miscellaneous The equipment room or the cabinet is waterlogged.
on between the smoke sensor and the monitoring device is faulty.Miscellaneous The equipment room or the equipment is on fire.
ction between the sensor and the monitoring device is faulty.Miscellaneous The door of the equipment room or the cabinet is open.
be controlled.Miscellaneous None
s insufficient.
tup signals of the diesel generator is faulty.Miscellaneous The fuel in the diesel generator is insufficient.
ar array cannot receive any sunshine for a long period of time. The solar array is shielded from sunshine.
etween the BBU and the monitoring device are incorrect. The cable connections between the BBU and the monitoring device are loose, wo
ous Some programs or protocols, such as hackers or viruses, that may generate broadcast packets exist on the network.
e Peer NE.Software The ETH OAM function is faulty.Hardware The Ethernet transmission link is faulty.Miscellaneous The Ethernet port of
be poor.Miscellaneous None
g modes of ETHOAM 3AH at both the local end and the peer end are set to PASSIVE.Software NoneHardware NoneMiscellaneous The E
between the base station and the SeGW fails. The certificates at both ends are issued by different CAs. Updating the certificate fails.
llaneous The local transmission port is faulty. The transmission link is faulty.
faulty.Miscellaneous The board (non-control board) to which the alarm pertains to is not installed or is not properly installed. The board (no
ck is extremely high or low.
rol board is not securely installed.Miscellaneous None
n the BBU exceeds the power supply capability of the power module in the BBU.Miscellaneous The AC mains supply fails or the power cab
rcuited or short-circuited. The GPS feeder is open-circuited or shot-circuited. The antenna is faulty.Miscellaneous None
rrier exists around the GPS antenna. The GPS satellite card hardware is faulty.Miscellaneous None
The GPS satellite card hardware is faulty.Miscellaneous None
e subrack that houses the board) is not securely installed. The board does not exist or is not securely installed.
soft failure or software program error.Hardware The board hardware is faulty. The hardware of the main control board (in the subrack that
n the case of a too high board temperature. The power supply capability of the power module is insufficient.Miscellaneous If the user enab
Hardware The hardware of the transmit board or receive board is faulty.Miscellaneous The transmit board is powered off. The transmit boa
necting piece on the transmission port of the BBU is faulty.Miscellaneous The optical module on the transmission port of the BBU is faulty.
evice is faulty. Board hardware: The board with the faulty transmission port is faulty. The hardware on the transmission port of the peer tra
nstalled securely, or the cable connection on the optical module is loose. The optical connector on the transmission port of the BBU is dirty.
the optical module or electrical port is faulty. The optical module on the port of the BBU connecting to the lower-level RF units is not in posit
F units is faulty. The optical module of the lower-level RF unit is faulty. The lower-level RF unit is faulty.Miscellaneous The optical module
cal module is loose. The optical port on the lower-level RF units malfunctions.Miscellaneous The optical module on the port of the BBU con
s faulty.Hardware If the optical transmission is used, the optical module of the lower-level RF unit connected to the BBU is faulty. If the opti
d, the baseband board working in the mode that aggregates data has hardware faults, is not installed, is not powered on, or is not configure
opology configuration is consistent with the actual network (both are the ring topology), but there is one (only one) configured port which is in
lot No. of the baseband board providing the CPRI chain is incorrect. In baseband extension mode, the TRX configuration exceeds the capa
e IP clock link may fail. If the clock reference is GPS clock, the GPS antenna may be faulty or the number of locked GPS satellites may be
trol board or UTRP hardware is faulty. The route from the NE to the clock server is not reachable. The QoS of the IP transport network is p
non-main control board, the board may not be securely installed.
s repeatedly reset because the connection between the base station and U2000 is disrupted for a long time. The base station in the other m
ulti-mode base station. The loading control rights are inconsistent between the current mode and the other mode.Software NoneHardware
dware model of the installed RF unit is incorrect.Miscellaneous None.
d position of a main control board of a mode is incorrect.Miscellaneous None
connected securely. The cable for the optical module on an inter-BBU port is faulty.Miscellaneous None
an inter-BBU port is not installed properly, or the cable connection on the optical module is not ready. The optical connector of an inter-BB
aneous The peer optical connector of an inter-BBU port or the optical module is not inserted properly, or the fiber optic cable fails to be con
combined base stations is not connected properly. The cable connecting the combined base stations is faulty.Miscellaneous None
vice (upper- or lower-level RF unit or the BBU) is not in position, or the cable connection on the optical module or electrical port is not ready
it/s, but an optical module of 1.25 Gbit/s is installed on the RF unit.Miscellaneous None
vel RF unit is dirty. The current-level RF unit is faulty. The peer device (upper-level/lower-level RF unit) is not powered on. The optical mod
the electrical transmission is used, the cable connector of the RF unit or peer device may be improperly installed, or the cable is faulty. Th
t-level RF unit is dirty. The optical module on the port of the current-level RF unit is not supported by the current-level RF unit, in terms of ty
ked or damaged, or the feeder is deformed. Hardware connections of the antenna TX and RX modes on the TRX board are inconsistent w
ected to the RF unit is faulty, which results in a high passive intermodulation power of the main or diversity antenna. Hardware connections
ly low value for the other mode of the multimode RF units.Software NoneHardware The jumper installation does not conform to the plan. T
eeder and the antenna device is loose. The ALD power supply circuit of the RF unit is faulty. The antenna device is faulty.Miscellaneous N
connected to the multi-wire port.Software NoneHardware NoneMiscellaneous None
an RAT.Miscellaneous None
program of the RF unit runs improperly.Hardware NoneMiscellaneous None
nit is faulty.Miscellaneous None
ect. For example, the vendor code, equipment serial number, or antenna type is not configured or incorrect; the control port is incorrectly con
s also not powered on or works improperly. The address settings of the DIP switch on the backup power device are incorrect. The connect
witch on the serial port device are incorrect. The connection between the RF unit and the serial port device is not ready, or the cables are fa
e hardware of the RF unit is faulty. The antenna is faulty. RF unit and antenna frequency band not alignment.Hardware NoneMiscellaneou
cause of RET antenna reset or maintenance link disconnection, the data configuration on the base station is inconsistent with that on the R
nk disconnection, the data configuration on the base station is inconsistent with that on the TMA. The configured data of the TMA is lost or
s to connect to the base station with an expired certificate. The CRL file to cancel the certificate is invalid.
ificate is about to expire. That is, the time span between the current time and the expiration time of the loaded certificate is below the user-d
. The certificate has not taken effect.
aneous The transmission network is faulty. The certificate and CRL server or the Certificate Authority (CA) server is abnormal. The certifica
e feeder connector is loose or waterlogged. The feeder is extruded and deformed. The jumper between the feeder and the antenna device
are The software running on the BBU or TRX board is faulty.Hardware The main control board or TRX board is faulty. Link resources inside
vation Abnormal, the causes are as follows: (1) Abnormal channel conversion. The channel type or channel status on the BSC side is incon
is faulty. Engineering issues are incorrect.Miscellaneous Uplink or downlink interference occurs. No user is served by the TRX (no action
number of TRXs, and bandwidth of RF modules are incorrect in co-module software-defined ratio (SDR) mode.Software NoneHardware T
ntenna TX and RX modes on the TRX board are inconsistent with data configurations.. The antenna system is damaged.Miscellaneous No
ards (in other modes) carrying the inactive transmission link is not configured. The route for the inactive transmission link is not configured
orrect frame alarms occur on the transmission link.
the clock reference source is obtained is manually reset.The board is not properly inserted, and the clock bus of the backplane is faulty.
n manual handover mode, the selected clock reference source is unavailable.In manual handover mode, the selection of the clock reference
connected securely.The status of the reference clock source working with the active GCU or GCG board is abnormal.
ackets with incorrect source MAC addresses.Packets are rewritten during the transmission inside the BSC6900, which leads to incorrect sou
et by using the [MML]RST BRD[/MML] command.Active and standby boards are switched over by using the [MML]SWP BRD[/MML] comma
y. The GE switching unit is faulty. The forwarding component is faulty.The board communication chips are faulty.The backup channel is fault
over 24 hours; the satellite card 1PPS signal is abnormal over 24 hours; or the satellite card time is abnormal. The clock model is that the c
ss of the active and standby OMUs is located of the active OMU differs from that of the standby OMU.The backup channel IP address of th
ve OMU or the standby OMU is changed, thus leading to the inconsistency of the software versions between the active OMU and the standb
sk or Raid, the hard disk or Raid is faulty.If the hardware type is ETH0, ETH1, or extra network adapter group: The cable connection of netw
f the active and standby OMUs conflicts with that of the fixed IP address of the internal network.The fixed IP address of the internal network
de in files under monitoring when operations using the omutool or MML commands are performed.Because of power failure, data in memory
e file.</p><p>The license file is damaged. </p><p>The license file expires.</p><p>The license file is revoked.</p>
sion exceeds the board specification. As a result, the switching capability on the board is insufficient, and therefore cannot provide services
SAU is abnormal.The slot housing the SAU is faulty.A self-check on the CPLD in the SAU fails.A self-check on the clock in the SAU fails.
eceive link of the peer NE is faulty.</p>The bit error rate of the transmit link from the BSC to the peer NE is too high.
performed from the transmission equipment to the peer NE.</p>
f the BSC is inconsistent with that of the peer equipment.</p>The E1/T1 cable of the BSC interface board is connected improperly.<p>The
om the BSC to the peer NE is faulty whereas the transmission link from the peer NE to the BSC is functional.</p><p>The receive link of the
formed from the transmission equipment to the peer NE.</p>
channel that the MSP multiplex section uses to receive the K2 byte and the number of the channel that the MSP multiplex section uses to s
protection mode and 1 indicating 1:N protection mode.)<p>The peer equipment is starting up.</p>
n network is faulty, and therefore the peer IP address cannot be reached. </p><p>The ports for transmitting and receiving packets at the loc
t.</p>The E1/T1 cables or optical cables that carry the PPP/MLPPP links are incorrectly connected.
ode.The MSP fails if the standby board is not in position or becomes faulty.
>The transmission equipment does not support the consistency check function on the Ater connection path.</p>
s situation, the Tx and Rx ports for all data flows corresponding to the IP address are not the same.The active and standby gateways are us
er end.No PDU received from peer end.The peer signaling links are deactivated.
Pb interface due to:Low congestion start thresholdInsufficient LAPD linksThis alarm may be generated on the Abis interface due to:Bit erro
, or the board is overloaded.The SCCP subsystem status on all signaling processing subsystems is inconsistent.
at packet loss occurs or delay prolongs.The peer device is incorrectly configured or in the abnormal state.
the BTS fails.The Abis transmission is faulty.The cell or the BCCH TRX of the cell is manually blocked.The BTS or cell is manually reset.Th
ion data but actually the BTS does not support Abis transmission optimization.The BTS is set to support automatic planning mode in configu
(1) The configuration of the equipment serial number (ESN) is incorrect. (2) The configuration of IP address is incorrect.BTS in GSM/UMTS
s to the CBC.</p>The communication between the BSC and the CBC is interrupted.
d Ater interfaces are incorrect. For example, there may be a crossed-pair connection.The TNU or DSP hardware is faulty.The Abis, Ater or A
cal function type is GTC have hardware faults.</p><p> When KPI Alarm Type is set to TNU Connectivity Success Rate Alarm, boards whos
e is faulty on the BSC side.A transport network between the BSC and the SGSN is faulty.The Gb interface is faulty on the SGSN side.
ot powered on or fails to be detected. The cable connections are faulty between the BBU/RRU and the monitoring device, between CCUs,
power. As a result, the secondary load is powered off when batteries are almost exhausted.
to the battery discharging and load low voltage disconnection (LLVD). The power supply capability of the PSU module is insufficient, after t
net is waterlogged.
quipment is on fire.
r the cabinet is open.
aneous The Ethernet port of Local NE is faulty. The Ethernet port of Neighbor NE is faulty. The Ethernet port of Peer NE is faulty.
e NoneMiscellaneous The Ethernet link is faulty. The peer device does not support the IEEE 802.3ah standard.
perly installed. The board (non-control board) to which the alarm pertains to is powered off.
s supply fails or the power cabinet is faulty, resulting in an improper -48 V DC input supplied for the BBU.
rol board (in the subrack that houses the board) is faulty.Miscellaneous The subrack where the board is located houses main control board
scellaneous If the user enables the energy conserving strategy, the board is automatically powered off when the energy conserving conditi
owered off. The transmit board or receive board does not exist or is not securely installed.
er-level RF units is not in position, or the cable connection on the optical module or electrical port is not ready. The connecting piece on the
laneous The optical module on the port of the BBU connecting to the lower-level RF units is not installed securely. The optical connector o
ule on the port of the BBU connecting to the lower-level RF units is dirty. The optical module on the transmission port of the BBU connecting
o the BBU is faulty. If the optical transmission is used, the interface board of the lower-level RF unit connected to the BBU is faulty. If the op
owered on, or is not configured.Software The RF unit is automatically reset due to a fault, or the RF unit is manually reset.Hardware The R
ne) configured port which is inconsistent with the actually used port.Software NoneHardware In the dual-star topology, more than one RRU
onfiguration exceeds the capability of the CPRI chain. In baseband extension mode, the physical resources corresponding to the TRX conf
ocked GPS satellites may be insufficient. Excessive frequency variation of external clock reference. The clock reference is unavailable due
of the IP transport network is poor. The transmission jitter is large and delay is long.Miscellaneous None
The base station in the other mode is reset after a software upgrade or after a reset command is issued. The main control board of the othe
tical connector of an inter-BBU port is dirty. The peer optical connector of an inter-BBU port or the optical module is not inserted properly. T
ber optic cable fails to be connected. The electrical cable for the peer inter-BBU port is not securely connected, or the electrical cable is fa
y.Miscellaneous None
or electrical port is not ready. The optical module on the port of the RF unit connecting to the peer device (upper- or lower-level RF unit or
powered on. The optical module or connector of the peer device (upper-level/lower-level RF unit or BBU) is improperly installed, or the optic
led, or the cable is faulty. The RF unit or peer device malfunctions, or the hardware is faulty. In multi-mode configuration, the inter-BBU co
ent-level RF unit, in terms of type (single-mode or multi-mode) and rate. The optical module or connector of the peer device (upper-level/low
TRX board are inconsistent with data configurations. The RX channel of the RF unit is faulty. For example, the low-noise amplifier, frequenc
enna. Hardware connections of the antenna TX and RX modes on the TRX board are inconsistent with data configurations. The feeder inst
oes not conform to the plan. The feeder connector on the antenna port does not meet the requirements, which is loose or waterlogged, or h
vice is faulty.Miscellaneous None
e control port is incorrectly configured.Software NoneHardware The ALD current of the RF unit is out of range There are feeder problems,
e are incorrect. The connection between the RF unit and the backup power device is not ready, or the cables are faulty. The backup powe
ot ready, or the cables are faulty. The serial port device is faulty.Miscellaneous None
nconsistent with that on the RET antenna. The configured data of the RET antenna is lost or modified on the base station.
red data of the TMA is lost or modified on the base station.
ver is abnormal. The certificate is invalid(Expired, Damaged, Format Error, Not Valid Yet).
eeder and the antenna device is loose.
s faulty. Link resources inside the BTS are insufficient. The BBU or an optical module inside the TRX board is faulty. The CPRI optical fibe
atus on the BSC side is inconsistent with that on the BTS side. (2) BTS or BSC software faults. The channel type or channel status on the B
served by the TRX (no action is required).
e.Software NoneHardware The RF unit is faulty.Miscellaneous None
s damaged.Miscellaneous None
mission link is not configured on the transmission network.Software NoneHardware Boards in other modes are faulty. These boards carry t
MML]SWP BRD[/MML] command.The board type is changed using the [MML]MOD BRD[/MML] command. The board is inhibited by using th
y.The backup channel is faulty.The logical unit is faulty.The packet switching unit is faulty.A service port is faulty.The switching unit is faulty.T
The clock model is that the clock in the GPS card synchronizes its time with the GPS satellites to maintain time accuracy. The configured c
ckup channel IP address of the active and standby OMUs of the active OMU conflicts with that of the standby OMU.The external fixed IP ad
The cable connection of network adapter ETH0 or ETH1 is interrupted. Network adapter ETH0 or ETH1 is faulty. The port on the switch con
ddress of the internal network and the virtual IP address of the internal network are on different network segments.The mask of the fixed int
power failure, data in memory is not written to the hard disk before the OMU shutdown. As a result, OMU files are lost.
onnected improperly.<p>The transmission equipment or transmission link between the BSC and the peer equipment is faulty.</p>The BSC
p><p>The receive link of the peer NE is faulty whereas the transmit link of the peer NE is functional.</p>The bit error rate of the transmissio
P multiplex section uses to send the K1 byte at the local end is inconsistent within five seconds.
d receiving packets at the local end are on different boards. </p><p>The DSCP is remarked by the bearer network.</p> <p>Not support the
and standby gateways are used when the BSC is configured with a policy-based routing based on a source IP address. The interconnected
Abis interface due to:Bit errorsExcessive downlink messages, such as immediate assignment messages, assignment messages, and pagin
TS or cell is manually reset.The BTS or cell is dynamically reconfigured, leading to a BTS or cell reset.The BTS main control board version d
matic planning mode in configuration data but actually the BTS does not support the automatic planning mode.The BTS is set to support Sin
incorrect.BTS in GSM/UMTS (GU) co-transmission mode: (1) The IP address of the DHCP server is not configured on the NodeB. (2) The D
re is faulty.The Abis, Ater or A interface board is faulty.A main control board or TRX board of the BTS is faulty.The transmission between the
ess Rate Alarm, boards whose logical function type is TNU have hardware faults.</p><p>When KPI Alarm Type is set to Interface Board Co
oring device, between CCUs, or between a CCU and another monitoring device. The cable is loose, worn-out, or broken between the BBU/
U module is insufficient, after the configured energy saving duration, LLVD occurs.
rt of Peer NE is faulty.
ed houses main control boards of the same mode and the intercurrent mode, and the intercurrent mode main control is configured on the bo
he energy conserving condition is met. The board is powered off because of a user command.
the transmission port of the BBU is not installed securely or dirty. The optical connector on the transmission port of the peer transmission d
BBU, in terms of type (single-mode or multi-mode) and rate. The optical fibers between the BBU and the peer transmission device are ben
topology, more than one RRU is connected to the RRU chain.Miscellaneous None
orresponding to the TRX configuration are unavailable. The port where the BTS monitoring timeslot is configured is not in the range of port
k reference is unavailable due to unacceptable quality. If the link clock(Trace BSC Clock or Trace Transport Clock) or synchronous-Etherne
main control board of the other mode is running improperly. The main control board of the current mode is running improperly.Hardware Th
ule is not inserted properly. The peer optical connector of an inter-BBU port is dirty. The optical modules on both ends of an inter-BBU por
d, or the electrical cable is faulty. The peer board of an inter-BBU port does not work properly. The optical connector or optical module in th
per- or lower-level RF unit or the BBU) is faulty, or the cable connected to the optical module or electrical port is faulty. The connecting piec
properly installed, or the optical module is faulty. The optical connector of the peer device (upper-level/lower-level RF unit or BBU) is dirty.
onfiguration, the inter-BBU connections are abnormal or the optical module used for inter-BBU connection is faulty.Miscellaneous None
e peer device (upper-level/lower-level RF unit or BBU) is improperly installed. Or the optical module is faulty. The optical connector of the p
low-noise amplifier, frequency mixer, analog to digital converter (ADC), or field programmable gate array (FPGA) is faulty.Miscellaneous N
onfigurations. The feeder installation is improper. For example, the feeder connector is loose, soaked or damaged, or the feeder is deforme
is loose or waterlogged, or has foreign matter. The feeder connected to the antenna port of the RF unit is bent or deformed; the feeder is d
There are feeder problems, such as water damage, connector fault, or bent cable. The hardware of the RF unit is faulty. The antenna dev
are faulty. The backup power device is faulty.Miscellaneous None
base station.
s faulty. The CPRI optical fiber between the BBU and the TRX board is faulty. The BSC interface board is faulty. A CPRI interface board in
pe or channel status on the BSC side is inconsistent with that on the BTS side. The cause of other specific problems is 'TRX module softw
e faulty. These boards carry the inactive transmission link. Network transmission is interrupted.Miscellaneous None
board is inhibited by using the [MML]INH BRD[/MML] or [MML]INH STANDBYSCU[/MML] command.The newly configured board starts up
y.The switching unit is faulty.The hard disk is faulty.The other component is faulty.
e accuracy. The configured coordinates of the GPS card is inaccurate. As a result, the GPS satellite cannot be traced and the clock model i
OMU.The external fixed IP address of the active OMU conflicts with that of the standby OMU.The internal fixed IP address of the active OMU
ty. The port on the switch connecting to the external network adapter is faulty.If the hardware type is the internal network adapter or internal
ents.The mask of the fixed internal IP address of the OMU is inconsistent with the mask of the virtual internal IP address of the OMU. The fix
bit error rate of the transmission link between the BSC and the peer NE is too high.
work.</p> <p>Not support the network, for example, the load sharing ethernet port.</p>
P address. The interconnected router is configured with two load-sharing routes that have the same priority. In this situation, the Tx and Rx p
gnment messages, and paging messagesThis alarm may be generated on the Ater interface due to:Bit errorsFaulty LAPD linksThis alarm m
S main control board version does not work with the TRX board version. The physical connections of the BCCH TRX board are inconsistent
The BTS is set to support Single RAN in configuration data but actually the BTS does not support Single RAN, or vice versa.The BTS is set
gured on the NodeB. (2) The DHCP relay function is disabled on the NodeB.The software on the BTS main control board is faulty.The softwa
The transmission between the BSC and the BTS is faulty.The transmission between the BSC and the MGW is faulty.This affects the O&M o
e is set to Interface Board Connectivity Success Rate Alarm, interface boards have hardware faults.</p>Statistical data does not meet para
or broken between the BBU/RRU and the monitoring device, between CCUs, or between a CCU and another monitoring device. The DIP
control is configured on the board. In BBU interconnection scenarios, the inter-BBU ports on the UCIU and UMPT are faulty. The board is n
port of the peer transmission device is not installed securely. The optical link between the transmission port of the peer transmission device
transmission device are bent, deformed, or worn-out. Or the length of optical fibers is excessive, which leads to a high attenuation of optica
ely or dirty. The interface board in the BBU connecting to the lower-level RF units is faulty. The optical module on the port of the BBU does
-level RF units, in terms of type (single-mode or multi-mode) and rate. The optical fibers between the BBU and lower-level RF units are ben
If the optical transmission is used, the lower-level RF unit is faulty. If the electrical transmission is used, the cable between the lower-level
rly. The fiber optic cable or electrical cable between the BBU and the RF unit or between upper- and lower-level RF units is faulty. The opt
red is not in the range of port numbers supported by the main control board. The E1 port No. of the BTS is beyond the the range (0, 1, 2, a
lock) or synchronous-Ethernet clock is applied , the transmission link between the base station and the clock reference may fail, or the frequ
ning improperly.Hardware The hardware of the main control board of the current mode is faulty. The hardware of the main control board of
oth ends of an inter-BBU port do not match, in terms of type (single-mode or multi-mode) and rate. The optical module on an inter-BBU po
nnector or optical module in the local inter-BBU port is not securely connected. The electrical cable for the local inter-BBU port is not secure
s faulty. The connecting piece on the port of the RF unit connecting to the peer device (upper- or lower-level RF unit or the BBU) is faulty.M
evel RF unit or BBU) is dirty. The peer device is faulty. The optical link between the current-level RF unit and the peer device (upper-level/l
ulty.Miscellaneous None
The optical connector of the peer device (upper-level/lower-level RF unit or BBU) is dirty. The optical module on the port of the peer device
nt or deformed; the feeder is damaged. The RF unit is faulty in hardware. The frequency bands supported by the RF unit do not match the
ty. A CPRI interface board in the BBU is faulty. The CPRI bandwidth is insufficient.Miscellaneous The transmission link between the BSC
oblems is 'TRX module software faults.'Hardware When the specific problems are Release Abnormal, High Call Drop Rate, Bad Uplink Qua
traced and the clock model is invalid. There are obstacles around the antenna. As a result, one of the following may occur: the locked sate
IP address of the active OMU conflicts with that of the standby OMU.The network segment on which the backup channel IP address of the
al network adapter or internal network adapter group: The internal network adapter of the OMU is faulty. The SCU board is reset. The SCU
P address of the OMU. The fixed IP address of the external network and the virtual IP address of the external network are on different netwo
this situation, the Tx and Rx ports for some data flows corresponding to the IP address are not the same.The gateways are not configured i
Faulty LAPD linksThis alarm may be generated on the Pb interface due to:Bit errorsFaulty LAPD links
or vice versa.The BTS is set to support the co-site mode in configuration data but actually the BTS does not support the co-site mode.The
ntrol board is faulty.The software on the BSC Abis interface board is faulty.The BTS main control board is faulty.The E1 lightning protection i
tical data does not meet parameter setting requirements of the KPI alarm.
monitoring device. The DIP switch setting of the monitoring device is wrong.Miscellaneous None
MPT are faulty. The board is not installed or is not securely installed. The board is powered off.
the peer transmission device and the BBU is faulty. Optical module: The optical module on the transmission port of the BBU is not installe
to a high attenuation of optical signals.
e on the port of the BBU does not match that of the lower-level RF unit, in terms of type (single-mode or multi-mode) and rate.The optical m
d lower-level RF units are bent, deformed, or worn-out. Or the length of optical fibers is excessive, which leads to a high attenuation of optic
able between the lower-level RF unit and the BBU is faulty. In multi-mode configuration, the inter-BBU connections are abnormal or the op
vel RF units is faulty. The optical module inside the BBU or RF unit is faulty. The hardware of the RF unit or BBU is faulty. When the dual-m
yond the the range (0, 1, 2, and 3) supported by the GTMU.Software Software is running improperly.Hardware NoneMiscellaneous The re
eference may fail, or the frequency deviation between the clock reference and the local clock may be excessively large. If the clock referen
e of the main control board of the other mode is faulty. In multi-mode configuration, the inter-BBU connections are abnormal or the optical m
al module on an inter-BBU port does not match that supported by the board, in terms of type (single-mode or multi-mode) and rate. The opt
al inter-BBU port is not securely connected. The board where the local inter-BBU port is not working properly.
n the port of the peer device (upper-level/lower-level RF unit or BBU) is not supported by the peer device, in terms of type (single-mode or m
na of the RF unit.
the RF unit do not match the frequency bands supported by the components of the antenna system. The components of the antenna syste
mission link between the BSC and the BTS is faulty. The cabinet is not properly grounded. The Abis transmission cable is not properly grou
all Drop Rate, Bad Uplink Quality, Bad Downlink Quality, or No Traffic on TRX, the causes are as follows: (1) The antenna on the uplink or d
ng may occur: the locked satellite number is abnormal (less than 4); the satellite card trace satellites number is not enough (less than 4) ove
up channel IP address of the active and standby OMUs is located conflicts with that on which the internal fixed IP address is located.The V
CU board is reset. The SCU board cannot be detected.If the hardware type is the backup channel network adapter: The active OMU or the
network are on different network segments.The mask of the fixed external IP address of the OMU is inconsistent with the mask of the virtual
gateways are not configured in active/standby mode and device IP address is used when the base station controller is configured with a pol
support the co-site mode.The BTS is set to support normalization of 3012 series base stations in configuration data but actually the BTS doe
y.The E1 lightning protection interface board of the BTS is faulty.The cable connection of the BTS is faulty.The Abis interface board of the BS
port of the BBU is not installed securely. The optical module on the transmission port of the peer transmission device is not installed secure
mode) and rate.The optical module on the port of the lower-level RF unit is not supported by the lower-level RF unit, in terms of type (single
to a high attenuation of optical signals.
ctions are abnormal or the optical module used for inter-BBU connection is faulty.Miscellaneous If the optical transmission is used, the optic
BU is faulty. When the dual-mode CPRI MUX topology is adopted, the optical module of the baseband board working in the mode that agg
e NoneMiscellaneous The related board or the NE is not reset after static parameters are set.
ely large. If the clock reference is PEER clock, the clock reference may be incorrectly configured in peer mode.
are abnormal or the optical module used for inter-BBU connection is faulty. Hardware of interconnected boards is faulty.Miscellaneous The
multi-mode) and rate. The optical module on an inter-BBU port does not match the connected fiber optic cable, in terms of type (single-mode
erms of type (single-mode or multi-mode) and rate. The optical fibers between the current-level RF unit and the peer device (upper-level/low
ponents of the antenna system include antennas, feeders, jumpers, combiner-dividers, filters, and tower-mounted amplifiers (TMAs). A com
he antenna on the uplink or downlink is faulty. (2) The channel on the TRX module is faulty. When the specific problem is Uplink and Downl
not enough (less than 4) over 24 hours; the satellite card 1PPS signal is abnormal over 24 hours; the satellite card time is abnormal.
d IP address is located.The VLAN configuration on the active OMU is inconsistent with that on the standby OMU.The standby OMU is faulty
apter: The active OMU or the backup network adapter of the standby OMU is faulty if the active and standby OMUs are configured. The sta
nt with the mask of the virtual external IP address of the OMU. The network segment of the backup channel IP addresses of the active and
roller is configured with a policy-based routing based on a source IP address. The route output port configured on the interconnected route
data but actually the BTS does not support normalization of 3012 series base stations.The primary TMU of a BTS is configured in a subrac
Abis interface board of the BSC is faulty.The transmission device or transmission link between the BSC and the BTS is faulty.A BTS power
F unit, in terms of type (single-mode or multi-mode) and rate. The optical link between the BBU and the lower-level RF unit is faulty. The op
ransmission is used, the optical connector or the optical module of the lower-level RF unit connected to the BBU is not securely installed. I
working in the mode that aggregates data is faulty. When the dual-mode CPRI MUX topology is adopted, the backplane link between the b
ds is faulty.Miscellaneous The main control board of the current mode is not installed securely. The main control board of the other mode is
in terms of type (single-mode or multi-mode) and rate. The fiber optic cable between inter-BBU ports is faulty. The peer board of an inter-B
e peer device (upper-level/lower-level RF unit or BBU) are bent, deformed, or worn-out. Or the length of optical fibers is excessive (longer th
nted amplifiers (TMAs). A component of the antenna system is damaged. The application environment of the RF unit reflects the RF signals
problem is Uplink and Downlink Imbalance, the causes are as follows: (1) The antenna on the uplink or downlink is faulty. (2) The channel
U.The standby OMU is faulty.The Ethernet port of the OMU is faulty or the Ethernet cable is disconnected.
OMUs are configured. The standby OMU board cannot be detected or is faulty if the active and standby OMUs are configured.If the hardwar
addresses of the active and standby OMUs conflicts with that of the fixed IP address of the external network.The network segment of the b
d on the interconnected router is inconsistent with that configured on the controller. In this situation, the Tx and Rx ports for all data flows co
BTS is configured in a subrack other than subrack 0 of cabinet 0 in configuration data but actually the BTS does not support the configuratio
e BTS is faulty.A BTS power failure occurred.The BTS was powered off to save energy.Bit errors occur during transmission between the BS
level RF unit is faulty. The optical module on the port of the lower-level RF unit is improperly installed, or does not match the connected op
BU is not securely installed. If the optical transmission is used, the optical module of the lower-level RF unit connected to the BBU is not se
backplane link between the baseband boards working in two modes has insufficient resources, or the backplane link is faulty. When the du
l fibers is excessive (longer than 40 km), which leads to a high attenuation of optical signals.Miscellaneous None
RF unit reflects the RF signals into the antenna system, causing an increase in VSWR for the RF unit.Miscellaneous None
ink is faulty. (2) The channel on the TRX module is faulty. (3) Inconsistency occurs between the configured TMA data and the actual TMA co
are configured.If the hardware type is that obtaining the slot No. fails: The OMU board is loosely inserted. The slot is faulty.If the hardware t
The network segment of the backup channel IP addresses of the active and standby OMUs conflicts with that of the debugging IP address o
Rx ports for all data flows corresponding to the IP address are not the same.The policy-based routing based on a source IP address is con
s not support the configuration.The BTS is set to support multiple IP addresses but actually the BTS does not support multiple IP addresse
transmission between the BSC and the BTS.
not match the connected optical fiber, in terms of type (single-mode or multi-mode) and rate. The optical connector of the lower-level RF u
nnected to the BBU is not securely installed. If the optical transmission is used, the optical link between the lower-level RF unit and the BB
ne link is faulty. When the dual-mode CPRI MUX topology is adopted, the hardware of the baseband board working in either side does not
neous None
MA data and the actual TMA connections.Miscellaneous When the specific problems are Uplink and Downlink Imbalance, High Call Drop Ra
slot is faulty.If the hardware type is that the CPLD or clock self check error occurs, the CPLD or clock hardware of the OMU if faulty.If the h
of the debugging IP address of the OMU.The network segment of the fixed IP address of the internal network conflicts with that of the fixed
on a source IP address is configured on the base station controller and uses the active and standby gateways. The router interconnected to
support multiple IP addresses.The number of configured TRXs or a TRX No. in the BTS exceeds the BTS specification.The number of conf
nector of the lower-level RF unit is improperly installed or dirty. The lower-level RF unit is not powered on.
wer-level RF unit and the BBU is faulty. If the electrical transmission is used, the cable between the lower-level RF unit and the BBU is not
orking in either side does not support backplane aggregation.Miscellaneous None
mbalance, High Call Drop Rate, Bad Uplink Quality, and Bad Downlink Quality, the cause is 'Uplink or downlink interference.' When the spe
e of the OMU if faulty.If the hardware type is that the temperature or voltage on the OMU board is abnormal: The OMU board hardware is fa
conflicts with that of the fixed IP address of the external network.The network segment of the fixed IP address of the internal network conflic
The router interconnected to the base station controller is configured with routes of different priorities. The route priorities are the same as
cification.The number of configured RXU cascading levels exceeds the BTS specification.The number of configured cells under a single BT
k interference.' When the specific problem is Release Abnormal, the causes are as follows: (1) Uplink or downlink interference (2) Transmis
he OMU board hardware is faulty. The running environment of the OMU board software is abnormal and therefore the detected value is abn
of the internal network conflicts with that of the debugging IP address of the OMU.The network segment of the fixed IP address of the extern
ute priorities are the same as the priorities of active and standby gateways on the base station controller and the SBFD is enabled on the ac
gured cells under a single BTS exceeds the BTS specification.Configuration data indicates that Abis transmission backup enhancement is c
nlink interference (2) Transmission faults. When the specific problem is No Traffic on TRX, the causes are as follows: (1) Uplink or downlink
fore the detected value is abnormal.If the hardware type is that the CPU, the number of CPU does not comply with OMU specifications.If th
fixed IP address of the external network conflicts with that of the debugging IP address of the OMU.The fixed IP address of the external ne
he SBFD is enabled on the active gateway. If the local route switchover delay configured in the STR IPCHK command is inconsistent with th
sion backup enhancement is configured for the BTS. Actually, the BTS does not support transmission backup enhancement.The BTS is con
ollows: (1) Uplink or downlink interference. (2) No user is served by the TRX (no action required).
with OMU specifications.If the hardware type is that the physical memory, the physical memory capacity does not comply with OMU specifi
IP address of the external network and the IP address of the default gateway are on different network segments.The fixed IP address of the
mmand is inconsistent with the convergence time of the network router, the Tx and Rx ports for all data flows of an IP address are not the s
enhancement.The BTS is configured to support mixed insertion of RFUs and RRUs but it does not.The BTS is set to support configuring sub
not comply with OMU specifications.If the hardware type is that the ejector levers of the OMU board, the ejector levers of the OMU board a
ts.The fixed IP address of the external network conflicts with the IP address of the default gateway.The network segment of the BSC local IP
of an IP address are not the same after the fault detected by the SBFD is rectified.
set to support configuring subsites in different multi-site cells on the same RF module but actually the BTS does not support such configura
es not support such configuration.The BTS does not support the configured RSL bearer type.The BTS is set to support configuring the TRX
BSC local IP address conflicts with the network segment of the IP address of the internal network.The network segment of the BSC local IP a
support configuring the TRX transmit and receive modes through antenna groups in configuration data but actually the BTS does not supp
segment of the BSC local IP address conflicts with the network segment of the backup channel IP addresses of the active and standby OM
of the active and standby OMUs.The internal network segment of the OMU is inconsistent with the configured one.