Escolar Documentos
Profissional Documentos
Cultura Documentos
sample only
Amount in Words:
Providing, fabricating and fixing MS banded sheet box frame of 10swg paint finish including
wastage, continuous welding, grinding, anchoring, approved three coats of paint over two coats of
anti rust paint, smooth finish, base preparation with putty prior to apply paint, all fixing accessories ID-801, 802.
and arrangements, scaffolding, etc. Complete in all respect and as per drawings, details & directions
of the Architect / Engineer.
Providing and laying cast in place cement concrete leveling screed rough finish ( floor / steps /
ramp / etc. ) Avg. 2" thick ratio 1:2:4 laid in panels using approved quality (cement, sand, crush)
ID-401. Sft. 3000 Rs. 225.00
including compacting, leveling, curing, wastage, all arrangements, etc. Complete in all respect and
as per drawing, details and directions of the Architect / Engineer.
Fixing of full body Owner Supplied porcelain tiles on already laid CC rough concrete floor (tiles to
be fixed with approved dry bond) including dry bond, approved unsanded grout, spacers in required
size, cutting, curing, cleaning, hacking / chipping of existing surface for bonding where necessary, ID-401.
wastage, all fixing accessories and arrangements, etc. Complete in all respects and as per drawing,
patterns and directions of the Architect / Engineer.
4.2.4 Vertical surfaces of podium & plinth protection including base rough plaster and dry bond. Sft. 550 Rs. 300.00
Providing and fixing of 3/4" thick approved polished marble strips inlay 3" wide (Baisc price of marble
Rs. 350/- per sft) in floor ( to be leveled with porcelain tile level ) including cutting, grinding, polishing,
ID-401. Rft. 300 Rs. 140.00
dry bond, all fixing accessories and arrangements, wastages, etc. Complete in all respects and as
per drawing, detail and directions of the Architect / Engineer.
Providing, making & fixing of main entrance door shutter ( D1 ) size 6'-0" x 8'-6" (In two panels) using
4" x 2" x 14swg MS tube for outer frame, 1/2" x 1/2" x 18swg MS tube for supporting of glass, 12mm
thick clear glass including paint finish MS posts (both sides) using 6" x 8" x 14swg MS tube fixed on
to floor and beam with plates and anchor bolts, cutting, welding, grinding, three coats of approved ID-101, 802. Job. 1
paint over two coats of anti rust paint, smooth finish, floor mounted door closer, hinges, lock,
wastage, all fixing accessories and arrangements, etc. Complete in all respects and as per drawing,
details & directions of the Architect / Engineer.
Providing and fixing of 12mm thick clear glass with paint finish MS tube frame including water proof
sealant, wastage, three coats of approved paint over two coats of anti rust paint, welding, grinding,
ID-101, 802. Sft. 700 Rs. 450.00
smooth finish, all fixing accessories and arrangements, etc. Complete in all respects and as per
drawing, details and directions of the Architect / Engineer.
Providing and installation polish finish plain false ceiling fabricated with 16mm thick marine ply with
red meranti wood lipping on edges over partal wood frame 1.5" x 1.5" @ 24" C/C at any height
including approved polish with lacquer over transparent sealer, making grooves, cutting for light ID-301, 302. Sft. 110 Rs. 880.00
fixtures, all fixing accessories and arrangements, scaffolding, wastages, etc. Complete in all
respects and as per drawings, design and directions of the Architect / Engineer.
Providing, fabricating and installation of wooden rafters fabricated with polish finish solid red meranti
wood size 2" x 4" hang from slab with 3/8" dia threaded shaft including approved polish with lacquer
over transparent sealer, scaffolding, fixing arrangement for LED smart panel, anchor bolts, all fixing ID-301, 302. Rft. 500 Rs. 1,050.00
accessories and arrangements, wastages, etc. Complete in all respect and as per drawings, details
& directions of the Architect / Engineer.
Providing, fabricating and installation of wooden rafters fabricated with polish finish solid red meranti
wood size 2" x 2.5" fixed on to already installed wooden rafters (Refer item # 7.2.a) including
approved polish with lacquer over transparent sealer, scaffolding, fixing arrangement for LED smart ID-301, 302. Rft. 130 Rs. 1,050.00
panel, all fixing accessories and arrangements, wastages, etc. Complete in all respect and as per
drawings, details & directions of the Architect / Engineer.
Providing, fabricating and placing of cash counter size 8'-9" long fabricated with deco paint finish MS
structure using different MS tubes of 16swg, MS sections, MS plates, 16swg corrugated MS sheet
(container type), 3/4" thick laminated MDF board with pvc lipping, 3/4" thick approved polished
marble (Baisc price of marble Rs. 350/- per sft), stainless steel brackets in drawers including making ID-701, 702,
Set. 1 Rs. 565,000.00
grooves, approved deco paint with all base prepsration and procedures, approved imported 703.
hardwares (locks, runners, handles, catchers, etc.), cutting, welding, bending, grinding, all fixing
accessories and arrangements, wastage, etc. Complete in all respects and as per drawing, details
and directions of the Architect / Engineer.
Providing, fabricating and fixing of 18'-0" long x 3'-0" high Back Counter fabricated with 3/4" & 1/2"
thick laminated board, red meranti wood polish finish for edges / louver shutter / etc, partal wood for
framing, 3/4" thick approved polished marble (Baisc price of marble Rs. 350/- per sft) including
ID-704. Set. 1 Rs. 9,595,500.00
approved polish with lacquer over transparent sealer, pvc lippings, all fixing accessories and
arrangements, wastage, etc. Complete in all respects and as per drawing, details and directions of
the Architect / Engineer.
Providing, fabricating and fixing of screen along cash counter fabricated with paint finish MS tube 1"
x 2" x 16swg vertical post fixed on to floor with MS base plate and anchor bolts, polish finish 1" x 1"
red meranti wood strips fixed on to MS post including approved paint over MS structure, approved ID-709. Sft. 40 Rs. 1,300.00
polish with lacquer over transparent sealer, all fixing accessories and arrangements, wastage, etc.
Complete in all respects and as per drawing, details and directions of the Architect / Engineer.
8.4.1 MS Posts.
Providing, fabricating and fixing of MS I beam (IPE shape 2.85 kg per rft) to be fixed on floor and
already installed storage racks with MS base plate and anchor bolts including three coats of
approved paint over two coats of anti rust paint, cutting, welding, grinding, all fixing accessories and ID-705. Rft. 310 Rs. 475.00
arrangements, wastages, etc. Complete in all respect and as per drawings, details and directions of
the Architect / Engineer.
Providing, fabricating and fixing of wooden rods polish finish fabricated with 1/2" x 1/2" paint finish
square shaft welded to already installed MS tubes, 1.5" x 1.5" polish finish red meranti wood batten
fixed on to shaft and wood notches including approved approved polish with lacquer over ID-705. Rft. 860 Rs. 190.00
transparent sealer, all fixing accessories and arrangements, wastages, etc. Complete in all respect
and as per drawings, details and directions of the Architect / Engineer.
Providing, making and placing of deco paint finish display table using MS tubes 1" x 1" and 1" x 2" of
16swg for frame, 3/16" thick MS bended sheet for base, 3/4" thick approved polished marble (Baisc
price of marble Rs. 350/- per sft), same marble gola on edges including approved deco paint with all
ID-707. Nos. 4 Rs. 375,000.00
base prepsration and procedures, approved polish with lacquer over transparent sealer, cutting,
welding, grinding, bending, adhesive, all fixing accessories and arrangements, wastage, etc.
Complete in all respects and as per drawing, details and directions of the Architect / Engineer.
Providing, fabricating and placing of wooden bench fabricated with 2.75" x 6" polish finish solid red
meranti wood planks fixed with MS deco paint finish legs including approved polish with lacquer over
transparent sealer, approved deco paint with all base prepsration and procedures, welding, grinding, ID-708. Nos. 4 Rs. 75,000.00
all fixing accessories and arrangements, wastages, etc. Complete in all respect and as per drawings,
details and directions of the Architect / Engineer.
Providing and installation of 5mm thick imported mirror pasted over 1/4" thick commercial ply with
MS paint finish U channel (bended sheet) and fixed on to already installed MS tubes of fabric display
including adhesive, cutting, welding, grinding, hinges, magnet, all fixing accessories and ID-706 Sft. 105 Rs. 425.00
arrangements, wastage, etc. Complete in all respects and as per drawing, details and directions of
the Architect / Engineer.
Providing and fixing of 12mm thick marine ply polish finish over already installed metal structure of
columns and beams including approved polish with lacquer over transparent sealer, all fixing
ID-101, 501. Sft. 830 Rs. 630.00
accessories and arrangements, wastage, scaffolding, etc. Complete in all respect and as per
drawings, details and directions of the Architect / Engineer.
8.9 MS Railing.
Providing, fabricating and fixing of MS railing using 2" x 4" MS tube of 14swg lacure finish including
cutting, welding, grinding, alignment, all fixing accessories and arrangements, anchoring, wastages, ID-602.
etc. Complete in all respects and as per drawing, detail and directions of the Architect / Engineer.
9.1 Paint.
Providing and applying three coats of matt enamel paint over cement board / MDF plain board /
wherever required including applying a coat of good quality primer, filling and preparation of smooth
9.1.1 Sft. 5100 Rs. 135.00
finish base surface prior to applying paint, scaffolding, etc. Complete in all respects and as per
drawings & directions of the Architect / Engineer.
Providing and applying three coats of weather shield (water proof) paint over cement boards external
9.1.2 walls including preparation of smooth finish surface prior to applying paint, scaffolding, etc. Complete Sft. 4100 Rs. 170.00
in all respects and as per drawings & directions of the Architect / Engineer.
IMPORTANT NOTES:
1- All prices should be quoted in “Pak. Rs." and inclusive of with holding tax.
2- All quantities are estimated and may vary on final completion of the respective works. Actual work done quantity should be measure for billing.
3- Abbreviations used in the Bill of Quantities are defined as follows:
Sft. = Square Feet. (Length x height / width)
Cft. = Cubic Feet. (Length x height x width / depth)
Rft. = Running Feet. (Length / height / width)
Nos. = Numbers. (Each)
4- Finished surface area up to false ceiling height will be measured for partitions / claddings / boxing. However, these items should be
minimum 4" high above false ceiling level.
5- Finished surfaces of false ceiling to be measured for billing.
6- Sample of materials should be submitted to the Project In-charge for approval prior to use at site.
7- Approval for execution of any works shall be taken in prior from the Project In-charge.
8- Before execution of works mockups shall be submitted by the contractor. The finishing details, polish and color shall be approved by the
Project In-charge.
9- Temporary Works will not be paid separately. All costs related to temporary work items are deemed to be included in the relevant unit rates.
10 - The contractor shall be responsible for the rectifications of existing finishes, if damage during execution of works.
11 - Clean and dust free environment to be strictly maintained at the all time at site
AMOUNT
Rs. 198,750.00
Rs. 66,250.00
Rs. 265,000.00
AMOUNT
Rs. 675,000.00
Rs. 399,000.00
Rs. 60,000.00
Rs. 8,000.00
Rs. 165,000.00
Rs. 42,000.00
AMOUNT
Rs. 42,000.00
Rs. 1,349,000.00
Rs. 550,000.00
AMOUNT
Rs. 315,000.00
Rs. 865,000.00
Rs. 96,800.00
AMOUNT
Rs. 525,000.00
Rs. 136,500.00
Rs. 758,300.00
AMOUNT
Rs. 565,000.00
Rs. 9,595,500.00
AMOUNT
Rs. 52,000.00
Rs. 147,250.00
AMOUNT
Rs. 163,400.00
Rs. 1,500,000.00
Rs. 300,000.00
AMOUNT
Rs. 44,625.00
Rs. 522,900.00
Rs. 61,250.00
Rs. 28,000.00
AMOUNT
Rs. 12,979,925.00
Rs. 688,500.00
Rs. 697,000.00
Rs. 1,385,500.00
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from th
In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Project In-charge before execution of works.
Falcon / Lucky / Pakland / Maple Leaf. (Only one brand shall be used to maintain consistency of shade sp
1 Cement. (OP / SR)
CC finish flooring & fair face plaster)
2 Aggregate. (Course / Fine) As approved by the Engineer. (Aggregate shall be clean and free from clay loam, silt, and other deleteriou
3 Fine sand. As approved by the Engineer. (Fine sand shall be clean and free from clay loam, silt, and other deleteriou
Potable clean and clear water which does not have sweet, saline OR brackish taste to be used for mixing
4 Water.
curing.
7 Solignum. English make- Jaffer Brothers. (For rough wood Solignum Brown and for finish wood Solignum Colorless)
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from th
In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Project In-charge before execution of works.
17 Plain glass. (Crystal clear, bubbles & distortion free float glass) (Guardian - Saudi Arabia) / (Saint Gobain Glass -United Kingdom)
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from th
In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Project In-charge before execution of works.
26 Oil Based Primer for Wall (Sealer & Undercoat). Jotun / ICI / Berger. (Pakistan)
27 Oil Based Primer & Undercoat for Wood. Jotun / ICI / Berger. (Pakistan)
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from th
In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Project In-charge before execution of works.
28 MS CR Tubes. International Industries Ltd. / Bashir Pipe Industries. / Kamal Pipe Industries. / Fazal steel
34 Scotch shield Safety and Security Anti Shatter Film. 3M SH7 Scotch shield 175 Microns / Equivalent.
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from th
In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Project In-charge before execution of works.
38 Steel Sections. Ishtiaq steel / Jabbar Steel / Mughal Steel / Saify Iron / Fazal Steel.
However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Project
Manufacturer / Supplier
Falcon / Lucky / Pakland / Maple Leaf. (Only one brand shall be used to maintain consistency of shade specially for
CC finish flooring & fair face plaster)
As approved by the Engineer. (Aggregate shall be clean and free from clay loam, silt, and other deleterious matter)
As approved by the Engineer. (Fine sand shall be clean and free from clay loam, silt, and other deleterious matter)
Potable clean and clear water which does not have sweet, saline OR brackish taste to be used for mixing and
curing.
English make- Jaffer Brothers. (For rough wood Solignum Brown and for finish wood Solignum Colorless)
However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Project
Manufacturer / Supplier
However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Project
Manufacturer / Supplier
Basfa - Gelaso.
However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Project
Manufacturer / Supplier
International Industries Ltd. / Bashir Pipe Industries. / Kamal Pipe Industries. / Fazal steel
Cementex. (Pakistan)
However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Project
Manufacturer / Supplier
Ishtiaq steel / Jabbar Steel / Mughal Steel / Saify Iron / Fazal Steel.
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Archite
Project In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Architect / Project In-charge before execution of works.
1 S.S Ball bearing door Hinge 4"x3"x3mm Th. Sisley/ Newise Italy
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Archite
Project In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Architect / Project In-charge before execution of works.
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Archite
Project In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Architect / Project In-charge before execution of works.
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Archite
Project In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Architect / Project In-charge before execution of works.
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Archite
Project In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Architect / Project In-charge before execution of works.
100mmx300mmx1
35 S.S Push Plate Newise /Euroart China/UK
.5mm th
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Archite
Project In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Architect / Project In-charge before execution of works.
PVC Heavy Duty Swivel Caster Wheels 360 Degree Top Plate with
37 Brake Pack of 4 (880Lbs).
3" COOCHEER China
39 Fixed Glass Aluminum Chanel Any size ALUM EX/ Chawla Pakistan
A- Materials shall be supplied only from the approved sources. However in all cases the contractor shall submit complete technical details of materials and obtain approval from the Archite
Project In-charge prior to deliver on site.
B- Approval of samples / mockups shall be taken from the Architect / Project In-charge before execution of works.
ll cases the contractor shall submit complete technical details of materials and obtain approval from the Architect /
Image
ll cases the contractor shall submit complete technical details of materials and obtain approval from the Architect /
Image
ll cases the contractor shall submit complete technical details of materials and obtain approval from the Architect /
Image
ll cases the contractor shall submit complete technical details of materials and obtain approval from the Architect /
Image
ll cases the contractor shall submit complete technical details of materials and obtain approval from the Architect /
Image
ll cases the contractor shall submit complete technical details of materials and obtain approval from the Architect /
Image
ll cases the contractor shall submit complete technical details of materials and obtain approval from the Architect /
Image