Escolar Documentos
Profissional Documentos
Cultura Documentos
INTRODUCTION
The term grease is used to describe semisolid lubricants. Although the
word grease is also used to describe rendered fat of animals, in the
context of lubrication, grease typically applies to a material consisting of
a soap emulsified with mineral or vegetable oil. Any filterable solvent-
soluble substances (e.g., elemental sulfur, complex aromatic compounds,
hydrocarbon derivatives of chlorine, sulfur, and nitrogen, and certain
organic dyes) that are extracted and recovered are defined as oil and
grease. No known solvent will dissolve selectively only oil and grease.
Heavier residuals of petroleum may contain a significant portion of
materials that are not solvent- extractable.
Oil and grease has the natural tendency to float on the water surface
under quiescent conditions, as the density of oil and grease is usually
less than one. Not all the oil and grease is in liquid or solid form.
Appreciable amounts remain in a finely divided emulsified form.
Oil and grease is an important parameter for water quality and safety.
Regulatory bodies worldwide set limits in order to control the amount oil
and grease entering the water reservoirs or the sea through industrial
discharges and also limit the amount present in drinking water.
OBJECTIVE(S)
To learn how to measure the oil level in water.
To learn the partition gravimetric method.
To calculate the oil and grease content in water sample (SST Lake).
METHODOLOGY
MATERIALS
Petroleum ether
Sulfuric acid (1:2, prepared by adding 50 ml concentrated sulfuric
acid slowly to 100 ml distilled water)
Ethyl alcohol (C2H5OH)
Separating funnel (500 ml)
Filter paper
Filter funnel
Conical flask
Hot water bath
Analytical balance
The sample is allowed to stand until two layers, which are petroleum
ether at the upper and water at the bottom.
The water at the bottom is discarded from the funnel and the petroleum
ether on the top is drained through the filter paper inside the filter
funnel into the pre-weighed conical flask.
Some fresh petroleum ether is poured through the filter paper to ensure
no oil and grease stuck in the paper.
The conical flask is placed in the hot bath and allows the petroleum ether
to evaporate. The conical flask is allowed to cool and weigh.
10mL of sulfuric acid, 50mL of Petroleum ether and 3mL Ethyl alcohol are
added to 230 mL sample in separating funnel. The funnel is well shaken.
METHOD
PRINCIPAL ANALYSIS
Chemicals which contained mainly aliphatic and aromatic hydrocarbon
also referred to the term “oil and grease” which derived from varied
sources that is from the crude petroleum and also from the industrial
derivatives. Because of low biodegradability the major contaminant of
concern are oil and grease originate from petroleum (fossil fuel) and also
their derivatives which can be found widely used in industries.
RESULT
Table 2.0 Determination of oil in water
V = volume of sample
250 ml
= 0.152 mg/L-1
DISCUSSION
Oil and grease are the important parameters that are used in water
quality measurement. The presence of oil and grease always can be seen
in a water sample. What varies in the presence of the oil and grease in a
water sample is the amount. The amount of oil and grease can be high
or low depending on the water sample and the nature of the water. To
determine the amount of oil and grease that present in the water sample
we use the partition gravimetric method. This method involves the
extraction of dissolved or emulsified oil and grease from water by using
an extracting solvent. Oil and grease in the water sample are referred to
the all the filterable solvent soluble substances such as elemental sulfur,
complex aromatic compounds, hydrocarbon derivatives of chlorine,
sulfur and nitrogen and certain inorganic dyes that are extracted and
recovered. Heavier residuals of petroleum may contain a significant
portion of materials that are not solvent extractable.
In this water quality analysis, we had determined the amount of oil and
grease in SST lake water. First the water sample was collected from the
lake. When the sample was collected, the lid of the bottle was closed
below the water surface. This is to avoid the content of the oxygen to be
high. First, 10ml of sulfuric acid, 50ml petroleum ether and 3ml ethyl
alcohol added to 250ml sample in separating funnel. The mixture was
shaken well to ensure that all the mixture mix well and the oil and grease
will be able to separate from the water. When the mixtures mix well, it
allowed standing till 2 layers are formed. The upper layer is petroleum
while the second layer is the water. The water layer discarded from the
funnel and the remaining petroleum filtered through the filter paper.
This to ensure that the oil and the grease to remain at the filter paper.
The final weight was determined in order to find out the weight of the oil
and grease content in the water.
According to the calculation, the final weight of the oil and grease
content in the water is 0.152 mg/L-1. This shows that the content of the
oil and grease in lake water is low. This is because the lake is not
exposed to any factors that contribute to the content of oil and grease
content in the water. The sources of oil and grease in water can be
caused by some factors such as petroleum refining, used oil refining and
crude oil production facilities.
Industrial plants use water as a coolant. They draw water from the nearby
water bodies like a river or a lake. The used-up water is returned to the
water bodies. The temperature of discharged water is higher than the
temperature in the water bodies. The difference in temperature can be
harmful to aquatic lives as they are not adapted to this temperature
change. The pollution thus caused is called thermal pollution. The
thermal pollution also causes decrease in the level of dissolved
oxygen present in the water which affects the aquatic lives on the earth.
CONCLUSION
As a conclusion of this experiment we can conclude that we had
achieved all the objectives of this experiment. From this experiment we
had learnt on how to conduct partition gravimetric method. apart from
that we had also calculated the amount of oil and grease in the SST Lake
water that is 0.152 mg/L-1. Based on the standard given the amount of
oil and grease in SST Lake water is still in a preferred level.