Você está na página 1de 12

NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

Last Modified: 7-25-2017 6.8:8.0.51 Doc ID: RM0000011BQ019X


Model Year Start: 2007 Model: LS460 Prod Date Range: [09/2006 - ]
Title: NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS OF ECU; 2007 MY LS460
[09/2006 - ]

TERMINALS OF ECU
1. CHECK DISPLAY AND NAVIGATION ASSEMBLY

(a) Disconnect the L59 display connector.

(b) Measure the resistance and voltage according to the value(s) in the table below.

TERMINAL NO. WIRING TERMINAL CONDITION SPECIFIED


(SYMBOLS) COLOR DESCRIPTION CONDITION

L59-1 (+B1) - L59-10


R - W-B Battery Always 11 to 14 V
(GND1)

L59-2 (ACC) - L59-10


LG - W-B Accessory (ON) Engine switch off Below 1 V
(GND1)

L59-2 (ACC) - L59-10 Engine switch on


1 of 12 LG - W-B Accessory (ON) 11 to 8/15/17,
14 V 5:31 PM
NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

(GND1)

L59-2 (ACC) - L59-10 Engine switch on


LG - W-B Accessory (ON) 11 to 14 V
(GND1) (ACC)

L59-3 (IG) - L59-10


V - W-B Ignition (ON) Engine switch off Below 1 V
(GND1)

L59-3 (IG) - L59-10 Engine switch on


V - W-B Ignition (ON) 11 to 14 V
(GND1) (IG)

L59-10 (GND1) - W-B - Body


Ground Always Below 1 Ω
Body ground ground

If the result is not as specified, there may be a malfunction on the wire harness side.

(c) Reconnect the L59 display connector.

(d) Measure the voltage according to the value(s) in the table below.

TERMINAL NO. WIRING TERMINAL CONDITION SPECIFIED


(SYMBOLS) COLOR DESCRIPTION CONDITION

L59-7 (TC) - Diagnosis ON


P - W-B Engine switch on (IG) 9 to 14 V
L59-10 (GND1) signal

L59-5 (HILL) -
LG - W-B Illumination signal Light control switch OFF Below 1 V
L59-10 (GND1)

L59-5 (HILL) -
LG - W-B Illumination signal Light control switch ON 11 to 14 V
L59-10 (GND1)

L59-12 (ILL+) -
G - W-B Illumination signal Light control switch OFF Below 1 V
L59-10 (GND1)

L59-12 (ILL+) -
G - W-B Illumination signal Light control switch ON 11 to 14 V
L59-10 (GND1)

L59-13 (REV) - See "Vehicle Signal Check"


R - W-B Reverse signal -
L59-10 (GND1) Mode

L59-14 (SPD) - Speed signal from See "Vehicle Signal Check"


V - W-B -
L59-10 (GND1) combination meter Mode

L59-23 (PKB) - Parking brake See "Vehicle Signal Check"


V - W-B -
L59-10 (GND1) signal Mode

L60-5 (TSW-) - Telephone relation


BR - W-B Always Below 1 V
L59-10 (GND1) switch signal

L60-12 (SGND)
- L59-10 BR - W-B Signal ground Always Below 1 V
(GND1)
2 of 12 8/15/17, 5:31 PM
NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

- L59-10 BR - W-B Signal ground Always Below 1 V


(GND1)

Microphone
L60-9 (MACC) -
R - W-B amplifier power Engine switch off Below 1 V
L59-10 (GND1)
supply

L60-9 (MACC) - Microphone


L59-10 R - W-B amplifier power Engine switch on (IG) 5V
(GND1)*1 supply

L60-10 (MIN-) - Microphone voice See "Microphone & Voice


BR - W-B -
L59-10 (GND1) signal Recognition Check"

L60-11 (MIN+)
Microphone voice See "Microphone & Voice
- L59-10 Y - W-B -
signal Recognition Check"
(GND1)

L60-13 (CA+) -
Television camera Engine switch on (IG), shift
L59-10 B - W-B Approx. 6 V
power supply lever in reverse position
(GND1)*2

L60-14 (CGND)
R - Body
- Body Ground Always Below 1 V
ground
ground*2

L60-27 (V+) - Pulse generation


Television camera Engine switch on (IG), shift
L60-14 W-R (refer to waveform
image signal lever in reverse position
(CGND)*2 1)

L60-28 (V-) -
Shielded -
L60-14 Shielded ground Always Below 1 V
R
(CGND)*2

Waveform
L60-21 (IVO-) - Voice guidance
R - W-B Voice guidance is provided synchronized with
L59-10 (GND1) signal
sounds is output

L60-22 (IVO+) Waveform


Voice guidance
- L59-10 G - W-B Voice guidance is provided synchronized with
signal
(GND1) sounds is output

L60-23 (SLD) - Shielded -


Shielded ground Always Below 1 V
L59-10 (GND1) W-B

L61-1 (VV+) - Pulse generation


DVD is played on radio
L59-10 W - W-B DVD image signal (refer to waveform
receiver
(GND1)*3 2)

L61-4 (VV-) -
L59-10 B - W-B Signal ground Always Below 1 V
(GND1)*3
3 of 12 8/15/17, 5:31 PM
NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

L59-10 B - W-B Signal ground Always Below 1 V


(GND1)*3

AVC-LAN
L60-4 (TX2+) -
LG - W-B communication Engine switch on (ACC) 2 to 3 V
L59-10 (GND1)
signal

AVC-LAN
L60-3 (TX2-) -
L - W-B communication Engine switch on (ACC) 2 to 3 V
L59-10 (GND1)
signal

L60-18 (TX3+) AVC-LAN


- L59-10 G - W-B communication Engine switch on (ACC) 2 to 3 V
(GND1) signal

AVC-LAN
L60-17 (TX3-) -
R - W-B communication Engine switch on (ACC) 2 to 3 V
L59-10 (GND1)
signal

AVC-LAN
L60-1 (TX-) - B*4 or
communication Engine switch on (ACC) 2 to 3 V
L59-10 (GND1) Y*5 - B-W
signal

AVC-LAN
L60-2 (TX+) - Y*4 or
communication Engine switch on (ACC) 2 to 3 V
L59-10 (GND1) B*5 - B-W
signal

AVC-LAN plus
L63-2 (TXO+) -
V - B-W communication Engine switch on (ACC) 0.15 to 0.6 Vpp
L59-10 (GND1)
signal

AVC-LAN plus
L63-3 (TXI+) -
P - B-W communication Engine switch on (ACC) 0.15 to 0.6 Vpp
L59-10 (GND1)
signal

AVC-LAN plus
L63-5 (TXO-) -
P - B-W communication Engine switch on (ACC) 0.15 to 0.6 Vpp
L59-10 (GND1)
signal

AVC-LAN plus
L63-6 (TXI-) -
O - B-W communication Engine switch on (ACC) 0.15 to 0.6 Vpp
L59-10 (GND1)
signal

L104-1 (GVIF) -
L59-10 B - BR Digital image signal - -
(GND1)*4

L108-1 (GVIF) -
B - BR Digital image signal - -
L59-10 (GND1)

L62-5 (SLD1) - Shielded -


Shielded ground Always Below 1 V
L59-10 (GND1) W-B
4 of 12 8/15/17, 5:31 PM
NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

L62-5 (SLD1) - Shielded -


Shielded ground Always Below 1 V
L59-10 (GND1) W-B

Waveform
L62-2 (FR-) - Sound signal Engine switch on (ACC),
G - W-B synchronized with
L59-10 (GND1) (right) Audio system playing
sounds is output

Waveform
L62-1 (FR+) - Sound signal Engine switch on (ACC),
R - W-B synchronized with
L59-10 (GND1) (right) Audio system playing
sounds is output

Waveform
L62-4 (FL-) - Engine switch on (ACC),
W - W-B Sound signal (left) synchronized with
L59-10 (GND1) Audio system playing
sounds is output

Waveform
L62-3 (FL+) - Engine switch on (ACC),
B - W-B Sound signal (left) synchronized with
L59-10 (GND1) Audio system playing
sounds is output

L62-8 (MUTE) - Sound library is playing → Above 3.5 V →


R - W-B Mute signal
L59-10 (GND1) Changing mode Below 1 V

L62-13 (SGD2)
Shielded -
- L59-10 Shielded ground Always Below 1 V
W-B
(GND1)*6

L62-10 (RL+) - Waveform


Sound signal Engine switch on (ACC),
L59-10 R - W-B synchronized with
(right) Audio system playing
(GND1)*6 sounds is output

L62-9 (RL-) - Waveform


Sound signal Engine switch on (ACC),
L59-10 G - W-B synchronized with
(right) Audio system playing
(GND1)*6 sounds is output

L62-12 (RR+) - Waveform


Engine switch on (ACC),
L59-10 B - W-B Sound signal (left) synchronized with
Audio system playing
(GND1)*6 sounds is output

L62-11 (RR-) - Waveform


Engine switch on (ACC),
L59-10 W - W-B Sound signal (left) synchronized with
Audio system playing
(GND1)*6 sounds is output

L62-7 (MUT2) -
Sound library is playing → Above 3.5 V →
L59-10 L - W-B Mute signal
Changing mode Below 1 V
(GND1)*6

Engine switch ON, light


L59-22 (DR) - control switch TAIL and
G - W-B Dimmer signal Above 9 V
L59-10 (GND1) cover the automatic light
control sensor

5 of 12 HINT: 8/15/17, 5:31 PM


NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

control sensor

HINT:
*1: w/o LEXUS Link System

*2: w/ Rear View Monitor System

*3: for DVD Changer Models

*4: w/ Advanced Parking Guidance System

*5: w/o Advanced Parking Guidance System

*6: w/ Rear Seat Entertainment System

If the result is not as specified, the display and navigation assembly may have a
malfunction.

(e) Using an oscilloscope, check the waveform 1.

Waveform 1 (reference)

ITEM CONTENT

Terminal No.
L60-27 (V+) - L60-14 (CGND)
(Symbols)

Tool Setting 0.2 V/DIV., 0.2 μs/DIV.

Engine switch on (IG), shift lever in


Condition
reverse position

(f) Using an oscilloscope, check the waveform 2.

Waveform 2 (reference)

ITEM CONTENT

Terminal No. (Symbols) L61-1 (VV+) - L59-10 (GND1)

Tool Setting 0.2 V/DIV., 0.2 μs/DIV.

Condition Disc is played on radio receiver

2. CHECK REAR POWER SEAT MODULE SWITCH (w/o Ottoman)

6 of 12 8/15/17, 5:31 PM
NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

(a) Disconnect the r2 module connector.

(b) Measure the resistance and voltage according to the value(s) in the table below.

TERMINAL NO. WIRING TERMINAL CONDITION SPECIFIED


(SYMBOLS) COLOR DESCRIPTION CONDITION

W - Body
r2-3 (E) - Body ground Ground Always Below 1 Ω
ground

r2-11 (B) - r2-3 (E) W-W Battery Always 11 to 14 V

If the result is not as specified, there may be a malfunction on wire harness side.

(c) Reconnect the r2 controller connector.

(d) Measure the voltage according to the value(s) in the table below.

TERMINAL NO. WIRING TERMINAL CONDITION SPECIFIED


(SYMBOLS) COLOR DESCRIPTION CONDITION

r2-4 (MPX+) - r2-3 AVC-LAN Engine switch on


W-W 2 to 3 V
(E) communication signal (ACC)

r2-5 (MPX-) - r2-3 AVC-LAN Engine switch on


W-W 2 to 3 V
(E) communication signal (ACC)

If the result is not as specified, the switch may have a malfunction.

3. CHECK REAR POWER SEAT MODULE SWITCH (w/ Ottoman)

(a) Disconnect the S15 module connector.


7 of 12 8/15/17, 5:31 PM
NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

(a) Disconnect the S15 module connector.

(b) Measure the resistance and voltage according to the value(s) in the table below.

TERMINAL NO. WIRING COLOR TERMINAL CONDITION SPECIFIED


(SYMBOLS) DESCRIPTION CONDITION

S15-5 (E) - Body W-B - Body


Ground Always Below 1 Ω
ground ground

S15-6 (B) - S15-5 (E) R - W-B Battery Always 11 to 14 V

If the result is not as specified, there may be a malfunction on wire harness side.

(c) Reconnect the S15 controller connector.

(d) Measure the voltage according to the value(s) in the table below.

TERMINAL NO. WIRING TERMINAL CONDITION SPECIFIED


(SYMBOLS) COLOR DESCRIPTION CONDITION

S15-10 (MPX+) - AVC-LAN Engine switch on


R - W-B 2 to 3 V
S15-5 (E) communication signal (ACC)

S15-11 (MPX-) - AVC-LAN Engine switch on


BR - W-B 2 to 3 V
S15-5 (E) communication signal (ACC)

If the result is not as specified, the switch may have a malfunction.

4. CHECK SATELLITE RADIO TUNER

(a) Disconnect the R27 tuner connector.

(b) Measure the resistance and voltage according to the value(s) in the table below.

TERMINAL NO. WIRING TERMINAL CONDITION SPECIFIED


(SYMBOLS) COLOR DESCRIPTION CONDITION

R27-7 (GND) - Body W-B - Body


Ground Always Below 1 Ω
8 of 12 ground ground 8/15/17, 5:31 PM
NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

R27-7 (GND) - Body W-B - Body


Ground Always Below 1 Ω
ground ground

R27-12 (+B) - R27-7


B - W-B Battery Always 11 to 14 V
(GND)

R27-11 (ACC) -
L - W-B ACC power supply Engine switch off Below 1 V
R27-7 (GND)

R27-11 (ACC) - Engine switch on


L - W-B ACC power supply 11 to 14 V
R27-7 (GND) (ACC)

If the result is not as specified, there may be a malfunction on the wire harness side.

(c) Reconnect the R27 tuner connector.

(d) Measure the voltage according to the value(s) in the table below.

TERMINAL NO. WIRING TERMINAL CONDITION SPECIFIED


(SYMBOLS) COLOR DESCRIPTION CONDITION

Waveform
R27-4 (L+) -
R - W-B Sound signal (left) Satellite radio ON synchronized with
R27-7 (GND)
sound is output

Waveform
R27-5 (L-) -
W - W-B Sound signal (left) Satellite radio ON synchronized with
R27-7 (GND)
sound is output

Waveform
R27-2 (R+) - Sound signal
B - W-B Satellite radio ON synchronized with
R27-7 (GND) (right)
sound is output

Waveform
R27-3 (R-) - Sound signal
G - W-B Satellite radio ON synchronized with
R27-7 (GND) (right)
sound is output

R27-1 (SLD) - Shielded -


Shielded Always Below 1 V
R27-7 (GND) W-B

R27-6 (MUTE) - Satellite radio ON → Above 3.5 V → Below


Y - W-B Mute signal
R27-7 (GND) Changing mode 1V

AVC-LAN
R27-9 (TX+) - Engine switch on
Y - W-B communication 2 to 3 V
R27-7 (GND) (ACC)
signal

AVC-LAN
R27-10 (TX-) - Engine switch on
BR - W-B communication 2 to 3 V
R27-7 (GND) (ACC)
signal

9 of 12 AVC-LAN 8/15/17, 5:31 PM


NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

signal

AVC-LAN
R28-3 (TXI+) - Engine switch on
V - W-B communication 2 to 3 V
R27-7 (GND) (ACC)
signal

AVC-LAN
R28-6 (TXI-) - Engine switch on
P - W-B communication 2 to 3 V
R27-7 (GND) (ACC)
signal

AVC-LAN
R28-2 (TXO+) - Engine switch on
V - W-B communication 2 to 3 V
R27-7 (GND) (ACC)
signal

AVC-LAN
R28-5 (TXO-) - Engine switch on
P - W-B communication 2 to 3 V
R27-7 (GND) (ACC)
signal

AVC-LAN
R29-12 (TX1+) - Engine switch on
Y - W-B communication 2 to 3 V
R27-7 (GND)*1 (ACC)
signal

AVC-LAN
R29-11 (TX1-) - Engine switch on
BR - W-B communication 2 to 3 V
R27-7 (GND)*1 (ACC)
signal

Engine switch on Waveform


R29-19 (RLI+) -
R - W-B Sound signal (left) (ACC), Audio system synchronized with
R27-7 (GND)
playing sound is output

Engine switch on Waveform


R29-20 (RLI-) -
W - W-B Sound signal (left) (ACC), Audio system synchronized with
R27-7 (GND)
playing sound is output

Engine switch on Waveform


R29-17 (RRI+) - Sound signal
B - W-B (ACC), Audio system synchronized with
R27-7 (GND) (right)
playing sound is output

Engine switch on Waveform


R29-18 (RRI-) - Sound signal
G - W-B (ACC), Audio system synchronized with
R27-7 (GND) (right)
playing sound is output

R29-16 (SLD4) - Shielded -


Shielded Always Below 1 V
R27-7 (GND) W-B

Audio system is
R29-14 (MUT3) - Above 3.5 V → Below
Y - W-B Mute signal playing → Changing
R27-7 (GND) 1V
mode

Sound library is
R29-15 (MUT2) - Y - W-B*2 Above 3.5 V → Below
Mute signal playing → Changing
R27-7 (GND) R - W-B*3 1V
mode
10 of 12 8/15/17, 5:31 PM
NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

R29-15 (MUT2) - Y - W-B*2 Above 3.5 V → Below


Mute signal playing → Changing
R27-7 (GND) R - W-B*3 1V
mode

Engine switch is on Waveform


R29-8 (FLI+) - R - W-B*2
Sound signal (left) (ACC), Sound library is synchronized with
R27-7 (GND) B - W-B*3
playing sound is output

Engine switch is on Waveform


R29-7 (FLI-) -
W - W-B Sound signal (left) (ACC), Sound library is synchronized with
R27-7 (GND)
playing sound is output

Engine switch is on Waveform


R29-10 (FRI+) - B - W-B*2 Sound signal
(ACC), Sound library is synchronized with
R27-7 (GND) R - W-B*3 (right)
playing sound is output

Engine switch is on Waveform


R29-9 (FRI-) - Sound signal
G - W-B (ACC), Sound library is synchronized with
R27-7 (GND) (right)
playing sound is output

R29-6 (SLD2) - Shielded -


Shielded Always Below 1 V
R27-7 (GND) W-B

R29-13 (MUT4) - RSE system is playing Above 3.5 V → Below


Y - W-B Mute signal
R27-7 (GND) → Changing mode 1V

Engine switch is on Waveform


R29-3 (RLO+) -
R - W-B Sound signal (left) (ACC), RSE system is synchronized with
R27-7 (GND)
playing sound is output

Engine switch is on Waveform


R29-2 (RLO-) -
W - W-B Sound signal (left) (ACC), RSE system is synchronized with
R27-7 (GND)
playing sound is output

Engine switch is on Waveform


R29-5 (RRO+) - Sound signal
B - W-B (ACC), RSE system is synchronized with
R27-7 (GND) (right)
playing sound is output

Engine switch is on Waveform


R29-4 (RRO-) - Sound signal
G - W-B (ACC), RSE system is synchronized with
R27-7 (GND) (right)
playing sound is output

R29-1 (SLD3) - Shielded -


Shielded Always Below 1 V
R27-7 (GND) W-B

HINT:
*1: w/ Disc Player

*2: w/ Rear Seat Entertainment System

*3: w/o Rear Seat Entertainment System

If the result is not as specified, the tuner may have a malfunction.


11 of 12 8/15/17, 5:31 PM
NAVIGATION: NAVIGATION SYSTEM (for HDD): TERMINALS O... https://one.tis.toyota.com/t3Portal/document/rm/RM0360U/xhtml/RM0...

If the result is not as specified, the tuner may have a malfunction.

5. CHECK RADIO RECEIVER

6. CHECK STEREO COMPONENT AMPLIFIER

12 of 12 8/15/17, 5:31 PM

Você também pode gostar