Escolar Documentos
Profissional Documentos
Cultura Documentos
UDC e21e2.211
Australian Standard
1110 1984
F
This Australian standard was prepared by Committce Ml/29, Fasteners. It was
approved on behalf of the ('ouncd of the Standards Association of Australia on
14 December l9i1 and published on ( lebruary I94.
Rvdvw q( .4 i.H,1s .iaA4rds. lo keep abreast ofprogress in industry, Australian standards are subject
ii, iwrnsln ,eirw and a,, kv,,l up.to-daie by the issue of amendments or new editions as necessary. It xs
impof time sh,rrfr,r chat ,ganda,d users ensure that they are in possession of the latest edition, and any
aflf,nd,,wns, ih,evto
lull detail. o/ all .%,4 4 ,uhl(i'aIlons will be found in the Annual List of Australian Standards; this informa-
non ii iuppl.nwnecd aeh month by SA A 'sjournal 'The Australian Standard', which subscribing members
rr vci, and whnh Riw., details of new publications, new editions and am endments, and of withdra wn stand-
a,.h
Ct ion lot Improvements to Australian standards, addressed to the head office of the Association, are
we!.. .me.! A'oqfl.'ailon of any inaccuracy or ambiguity found in an Australian standard should be made
without delay en order that the matter may be investigated and appropriate action taken.
AUSTRALIAN STANDARD
AS 1110-1984
PREFACE
This edition of this standard was prepared by the Association's Committee on Fasten-
ers to supersede AS 1110-1980.
Most of the changes incorporated in this edition are of an editorial nature. Other
changes include the following:
Inclusion in Table 10 of wedge-angle for property class 12.9.
Rewording of Clause 7.1 and Appendix G.
Correction of typographical errors in Tables.
This standard is based on and is in alignment with the following ISO standards, with
the exception that the tolerance on overall length of jsl6 has been retained:
ISO 272 FastenersHexagon ProductsWidths Across Flats
ISO 885 General Purpose Bolts and ScrewsMetric SeriesRadii Under the
Head
ISO 888 Bolts, Screws and StudsNominal Lengths and Thread Lengths for
General Purpose Bolts
ISO 898/1 Mechanical Properties of Fasteners
Part IBolts, Screws and Studs
ISO 4014 Hexagon Head BoltsProduct Grades A and B
ISO 4017 Hexagon Head ScrewsProduct Grades A and B
This is a free 5 page sample. Access the full version online.
CONTENTS
Page
SPECIFICATION
I Scope ..' 3
2 Referenced Documents 3
3 Definitions 3
4 Method of Manufacture .. 4
5 Shape, Dimensions and Finish 4
6 Materials and Mechanical Properties ........................5
Testing of Mechanical Properties of Hexagon Steel Bolts and Screws
7 5
8 Marking 7
APPEND!CES
A Non-preferred Sizes 20
B Basis for Derivation of Tolerances 22
C Shank and Head Dimensions for Hexagon Bolts and Screws over M36 23
D Drilled Bolts and Screws for Split-pins ........................24
E
F
Nuts....................................25
Recommended Combinations of Bolts and Screws with Associated
Notes on Hexagon Sizes of Metric Bolts and Screws ............26
G A Suggested Sampling Plan for Mechanical Properties 27
H Complete Designation for the Purpose of an Enquiry or Order 28
Australian Standard
for
ISO METRIC HEXAGON PRECISION BOLTS AND SCREWS
I SCOPE. This standard specifies requirements AS 1721 General Purpose Metric Screw Threads
for precision hexagon bolts (with full sized shanks) and AS 1815 Method for Rockwell Hardness Test
precision hexagon screws, with ISO metric coarse Part 1Testing of Metals
pitch series threads in diameters from 1.6mm to 36mm
inclusive. AS 1816 Method for Brinell Hardness Test
Part 1Testing of Metals
This standard is intended primarily to apply to steel
bolts and screws used within the temperature range of AS 1817 Method for Vickers Hardness Test
50°C to +300°C, and does not make provision for Part 1Testing of Metals
products requiring special properties, such as welda- AS 1897 Electroplated Coatings on Threaded
bility, or for corrosion-resistant materials. Components (Metric Coarse Series)
The dimensional and marking requirements (except ISO 273 Fasteners Clearance Holes for Bolts
property class marking) of this standard also apply to and Screws
non-ferrous and stainless steel fasteners. ISO 4014 Hexagon Head BoltsProduct Grades
NOTES: A and B.
This is a free 5 page sample. Access the full version online.
COPYRIGHT
This is a free preview. Purchase the entire publication at the link below: