Escolar Documentos
Profissional Documentos
Cultura Documentos
DIGITAL CAMERA
FinePix HS10/
HS11
SERVICE MANUAL
US/EE/E1/CH/JP-model
CAUTION
BECAUSE THIS PRODUCTIS RoHS LEAD-FREE COMPLIANT, USE THE DESIGNATED
AFTER-SELES PARTS AND THE DESIGNATED LEAD-FREE SOLDER WHEN
PERFORMING REPAIRS. (Refer to page 3)
WARNING
THE COMPONENTS IDENTIFIED WITH THE MARK " " ON THE SCHEMATIC DIAGRAM
AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST.
IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN ELECTRICAL
SHOCK.
Ref.No.: ZM00848-105
Printed in Japan 2011.03
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual
SAFETY CHECK-OUT
After correcting the original problem, perform the following
safety check before return the product to the customer.
1. Check the area of your repair for unsoldered or poorly 7. CAUTION: FOR CONTINUED
soldered connections. Check the entire board surface PROTECTION AGAINST FIRE
for solder splasher and bridges. HAZARD, REPLACE ONLY WITH
SAME TYPE 2.5 AMPERES
2. Check the interboard wiring to ensure that no wires 125V/250V FUSE.
are "pinched" or contact high-wattage resistors.
ATTENTION: AFIN D'ASSURER
RISK OF FIRE-
3. Look for unauthorized replacement parts, particularly REPLACE FUSE UNE PROTECTION
2.5A 125V/250V
AS MARKED
transistors, that were installed during a previous PERMANENTE CONTRE
2.5A 125V/250V
repair. Point them out to the customer and recommend LES RISQUES D'INCENDIE,
their replacement. REMPLACER UNIQUEMENT
PAR UN FUSIBLE DE MEME,
4. Look for parts which, though functioning, show TYPE 2.5 AMPERES, 125/250
obvious VOLTS.
signs of deterioration. Point them out to the customer
and recommend their replacement. 8. WARNING:
TO REDUCE THE ELECTRIC
5. Check the B + voltage to see it is at the values SHOCK, BE CAREFUL TO
specified. WARNING! TOUCH THE PARTS.
HIGH VOLTAGE
2
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual
<Lead-free soldering>
When lead-free solder is used, the solder tends to be less workable than when eutectic solder is used. When carrying out
repairs, use a designated lead-free solder, bearing in mind the differing work practices for eutectic solder and lead-free
solder.
■ Recommended equipment
lead-free
3
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual
MEMO
4
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual CONTENTS
CONTENTS
5
Confidential: FUJIFILM Service Center Use Only
CONTENTS FinePix HS10/HS11 Service Manual
MEMO
6
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 1. Disassembly
1. Disassembly
1-1. Removing the CABI BACK ASSY
(1)Remove SPRING TERMINAL SHOE in the direction of the arrow.
(2)Remove the 4 screw(SCR PAN PCS 1.7x6)
(3)Remove the HOLDER TERMINAL SHOE.
(4)Open the COVER JACK in the direction of the arrow.
(5)Lift up the LCD in the direction of the arrow.
(6)Open the BATTERY COVER in the direction of the arrow.
(7)Remove the 9 screw(SCR PAN PCS 1.7X4.0)
(8)Remove the 1 screw(SCR S-TPG PAN PCS 1.7X4.0)
2
7
3
5
4
1
7
8
7
7
11
9
10
[Assembly]
Assemble by performing the disassembly procedure in reverse.
1-1
Confidential: FUJIFILM Service Center Use Only
1. Disassembly FinePix HS10/HS11 Service Manual
5 4
3 Hook
1-2
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 1. Disassembly
7 8
(9)Release the 4 HOOKS and remove the COVER LCD BACK in the direction of the arrow.
(10)Remove the 4 screw(SCR PAN PCS 1.7X2.5)
(11)Remove DEC MONITOR in the direction of the arrow.
10
11 Hook
10
Hook
1-3
Confidential: FUJIFILM Service Center Use Only
1. Disassembly FinePix HS10/HS11 Service Manual
12
13
[Assembly]
Assemble by performing the disassembly procedure in reverse.
1-4
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 1. Disassembly
1-3. Removing the MAIN PWB ASSY
2
1
3
4
Take care not to touch the main capacitor terminals before discharging the capacitor.
1-5
Confidential: FUJIFILM Service Center Use Only
1. Disassembly FinePix HS10/HS11 Service Manual
6 7
7 6
6
9
8
7
[Assembly]
Assemble by performing the disassembly procedure in reverse.
1-6
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 1. Disassembly
1-4. Removing the FLASH UNIT
6
3
5 4
Hook 5
2
1
[Assembly]
Assemble by performing the disassembly procedure in reverse.
[Notes on Assembly]
Run the wire harnesses in the layout shown in the figure.
1-7
Confidential: FUJIFILM Service Center Use Only
1. Disassembly FinePix HS10/HS11 Service Manual
2
1
3
2
4
[Assembly]
Assemble by performing the disassembly procedure in reverse.
1
1
1-8
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 1. Disassembly
5
4
[Assembly]
Assemble by performing the disassembly procedure in reverse.
[Notes on Assembly]
Run the wire harnesses in the layout shown in the figure.
1-9
Confidential: FUJIFILM Service Center Use Only
1. Disassembly FinePix HS10/HS11 Service Manual
[Assembly]
Assemble by performing the disassembly procedure in reverse.
[Assembly]
Assemble by performing the disassembly procedure in reverse.
1-10
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 2. Schematics
2. Schematics 2-1. Block Diagrams
����� ����
�� � ��� � �� ��
��� � �� � �
�� �
� �� �����
�����
���������
�� � � �� ��
��������� �� �������
�������
���� �� � �� �� �� �� ��
����� ��� �� ��
�� �� � �� �� �
�� ��� �� ��� �� ���
�� �
����
�������������
����� ����� ���� �� �
� �������������� ����� � ������������������������
� � ������������������ �����
� ����� � ��������������������������
� �� �� � � �� �� ����
�� �
�
�� � ����������������������
�� � � ��������������� � �����
� �������������������
� �����������
� � ������ �� ��� � � ��������������� �����
� � �������������������������������� � ������������������
� ������������������� �����
� �������������������� � ��������������������� ���
�� ��� � �������
�� � � � ���
�� � � � � �� �
� ��������
� � ����������
� �������� ���
� � �������������������������������
���������
� � �������������������
� � �����������������������
� � � � ��
�� ���
�����
��� ���� ��������
������������
�� �
2-1
Confidential: FUJIFILM Service Center Use Only
2. Schematics FinePix HS10/HS11 Service Manual
���������� �������������
����� �����
����������� ����������
�������� �������� ������� ��������
�����
���� � ���������
��
� � �������� �
� � � � � � ��� � � � � � ��� � � � � � �
� � � � � � � �� �� ���� � � � � � �
� � � � � � �� �� ��
� � � � � � �� �� ��
� � � � �� �� �� �
� � � � � � �� �� �
����������
������
� � � �� �
� � � � � � �� �� ���� � � � � � �
��
���� �����
���� ����� �
�����
���� �����
� �������������
���� ����� ����� ������
������
���� ����� �
���� �����
��������� ��������������������
���� ����� ����������������
���� �����
������� �����
���� ����� �����
���� ����� ���� ���� ����� ������� �����
����
���� ����� ������� ����� �����
�����
���� �����
������� �����
�����
���� �����
���� �����
����� ��� �����
�����
���� ����� ����� ��� �����
���� ����� ������� ������ �����
�����
����� ��� ����� �����
� � �� ����� �����
������ � ������
� � �� ����� �������� �����
�����
�����
���������������������
�������� ���� �����
��������
�����
���������� �����
�������
�������� �����
��������� ���� �����
������� ���
��������� ����
�
��� ����
��� ���
���� ���� ��� ���
�������� ������� ���
�������
�
��������� �
��� ����� �� ���
��� �����
������� �
��� ����� ����
�������
����� ��� �������
���������� �������
������
����� ����� ��� ������ ������
������� �
����
���� ���
��������� �
������ ������� ���
�� � ��
����
2-2
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 2. Schematics
2-2-3. MAIN Block
� �� �
� �� ���
��� � � � ��� ��
�� � �� � ��� � � � �����
� ��
������ ������ ����� ��� � ����
� � ��� � � ��������� � � � � �����������
���� �����
�����
� ������
� ������
� � � ���� �� ��� � �
�������������
����� � � � � ������� � � ������ �� � � �� ��
���������������� � � �������� � � ������� � � ����� �� � ���� �� �� � �� � � � � � � � � � � ��
�������������������
� �� ��� � ���� � ���� � ��� �
����� ���������
�� � � �� �� �� �����
����� � � � ������������ ���� ��� ��� �� �
������ � � � ��� � � � ������ ����������
������� ��
� � � � �� �� � �� � �����
�����
� � � ��� � � �� �� ��
� � � � �� � �� ��� � ����
����������� � � � ��� � � � � � ��
���� ����
��� �� � �� � ��
� ��
� �� � ��
�� � � ��� � ��������
���������� �����
��� ���� ��� ���� � � ����� �� � ��� ������ ��
��� �� �� � ����
���� ����������� ����� �������������� ������
��������������
�����
�� � � ������ � � ��� � � ���� � ������ � � � �
��� ����������
�����
������ �� ���� �� � � ��� � � �� � � � ���� ��� � ���������
� �� � �
����� �������
� ��
�����
�����������
�� � � �����
����� � �� � ��
����� �����
���������
2-3
Confidential: FUJIFILM Service Center Use Only
2. Schematics FinePix HS10/HS11 Service Manual
������������
������������
����� ��� ������
�����������������
�����
�����
����� �������� ��� � ������� �����������
��������� ��������������� ���������
��������������
������� � ����� �
�������
������� ������
��� ��� ����
������� � ��
������
��������
� ����� �
���������� ����
���������� ��� ��� ����
� ��
��������
���������
���
�������� ��������
���������
������
����� �����
����������������� ����
����� �����
������
�����������������
�����
�������������� ��������
�
� ����
�����
��� ��������
� �����
������ �����
����������������� ��������
�������
�����
������ �����
�������� ���������������
���������
�����
������� ����
�������
�������� �������� �����
������� ������ ������
2-4
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 2. Schematics
2-2-5. FLASH Block
����������������
�������
������������ ����� ������������
������
������ �������
������ �������
���
������
�����
������ ����� � � ���� �����
FLASH
������ ��������
�������
������� ��������������
� ����������� �������
���
������� ������������
�� ���� �� �������
�� ������ �� �������
����������������������
2-5
FinePix HS10/HS11 Service Manual
Confidential: FUJIFILM Service Center Use Only
� ����
�����
� ���� � ����
� ����
�����
�����
�����
�����
�����
�����
�����
� ����
� ����
�����
�����
�����
� ���� � ����
�����
� ����
�����
�����
�����
� ����
� ���� � ����
8
� ����
�����
� � ���
�����
�����
� � ��� �� � � � � ����
�����
�����
�����
�����
� � ���
�����
� ����
�����
�����
�����
�����
� ���� � ����
SIDE B
� ����
�����
�� � � �
�����
� ����
�����
� ����
�����
� ���� � ����
����� �����
�����
�����
�����
�����
�����
�����
�����
� ���� � ����
� ����
����� �����
�����
� ���� �� � � � � ����
�����
� � ���
�����
� ����
�����
�����
�����
� ����
�����
�����
�����
�����
� ���� � ����
�����
�����
� ����
�����
�����
� ����
�����
�����
�����
�����
�����
�����
� ���� � ����
�����
� ���� � ����
�����
�����
�����
� ���� � ����
� ���� � ���� � ����
� ����
�����
�����
� ���� � � � ��� � � � �
�����
�����
�����
�����
� ����
�����
�����
� ����
� ���� � ����
�����
����� �����
�����
�����
� ����
� ����
�����
�����
�� � � �
� ���� � ���� � � ����
�����
�����
�����
�����
� ����
�����
�����
� ����
�����
� ����
�����
�����
�����
� ����
� ����
�����
�����
� ����
�����
�����
�����
� ����
�� � ���� � � ���
6
� ����
��
�����
�����
� ���� � ����
�����
�� � � � � ����
� ����
�����
� ����
� ����
�����
� ���� � ����
�����
� ���� � ����
� ����
�����
�����
� ����
5
� ����
� ����
��
�����
�� ��
�� ��
4
�� ��
�����
����� �����
�����
����� � ����
�� � ���� � ����
� ����
�� �� ��
�� � ���� � ����
�����
��
� ���� ����� � ����
�����
��
�����
�����
� ���� � ����
� ����
� ���� � ����
� � ��� ��
�����
�����
� ���� � ����
�����
� ���� F5003
�����
�����
�����
� ���� � ���� � ����
�����
� ����
�����
�����
� ���� � ����
� ���� � ���� � ����
�� � � � � � ��� � � ���
�����
� ���� � ����
�����
� ����
�� � ����
� ����
� ���� � ����
� � ��� � ���� � ���� � ����
�����
�����
� ����
� ���� � ���� � ����
�����
�����
� ���� � ����
� � ��� � ���� � ���� � ����
�����
�����
�����
� ���� � ����
�����
�����
�����
�����
�����
�����
� ����
�� � � � � ����
�����
�����
�����
�����
����� �����
� ����
�����
�����
�����
�����
�����
� ���� � ����
�����
�����
�����
�����
� ���� � ����
��
� ����
��
� ���� � ���� � ���� �� � � � � ����
��
� ���� � ����
�����
� ����
�����
�����
�����
F5001
F5002
� ���� �� � � �
�����
�����
�����
�����
� � ��� � ����
�����
�����
�����
�����
�����
� ���� � ����
� ����
��
� ����
� ����
�����
� � ���
� ���� � ����
�� � � � � ���� � ���� � ���� � ����
�����
�����
�����
� ���� � ���� � ����
3
�� � � � � ���� � ���� � ���� � ���� � ����
� ���� � ����
�����
� ����
�����
����� �����
����� �����
�����
�����
�����
�����
�����
� � ��� � ���� � ���� � ���� � ���� � ����
����� �����
����� �����
�����
�����
� ���� � ����
� ���� � ����
����� �����
����� �����
�����
�����
�����
�����
�����
SIDE A
� ����
�����
� ���� � ����
�����
� ����
�����
�����
�����
�����
� ���� � ����
� ���� � ����
� ����
� ���� � ���� � � ���
� ���� � ����
�����
�����
� ����
�����
�����
�����
�����
� ���� � ����
�� � � �
�����
� ����
� ����
�����
�����
�����
�����
�����
�����
� ����
�����
�����
�����
�����
� ����
�����
�����
� ����
�����
�����
�����
�����
�����
� ���� � ���� � ����
�����
�����
�����
�����
�����
� ���� � ����
�����
�����
�����
� ����
����� � ����
� ���� � ���� � � ��� � ���� � ���� � ���� � ����
�����
� ���� � ����
�����
� ���� � ����
�����
����� � ���� � ���� � � ��� � ����
�����
�� � � � � ���� � ����
� ����
�����
� ����
� ���� �� � � �
�����
2
�����
Mounted Parts Diagrams
� ����
� ���� � ����
� ����
� ����
� ����
� ����
�����
� ����
�����
� ����
�����
�����
�����
�����
� ����
� ����
�����
�����
� ���� �����
� ����
2. Schematics
� ����
�� �� � � ��
� ���� � ����
MAIN PWB ASSY
1
C
D
A
F
2-3-1.
2-3.
2-6
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 2. Schematics
� � �� ��� � �
�����
� ����� �
��
� �� � � �
� ����� �
��
� � ���
� � �� ��� � �
� �� � � �
B
� �� � � �
�����
� ����� �
� � �� ��� � �
<SIDE A> <SIDE B>
� � �� ��� � �
� ����� �
� �� � � �
2-3-3. COMPL PWB TB-3
����� ����� �����
� ����
� ����
� ����
� ����
� ����
� ����
� ���� � ����
����� ����� �����
C
�����
������
����� �����
�����
��
� ����� �
� � �� ��� � �
� �� � � �
��
� ����� �
�����
� ����
�����
E ���������
���������
����� �������
����� �������
������ ������
� ����
� ����
F5091
����� ����� �� ����� �����
��
�����
�� �����
�����
�����
�����
�����
��
�����
�����
�� ��
��
��������� ���������
��
F ������� ������� ��
������ ������
<SIDE A> <SIDE B>
<SIDE A> <SIDE B>
1 2 3 4 5 6 7 8 9
2-7
Confidential: FUJIFILM Service Center Use Only
2. Schematics FinePix HS10/HS11 Service Manual
MEMO
2-8
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3. Adjustments
3-1. Important point before adjustment
3-1-1. The handling of image files in internal memory
Image files contained in the internal memory should be handled as described below.
III. Procedure for PTP-connected cameras and images that cannot be downloaded to a PC
(Images can only be backed up to a PC. * Normally, back up images using procedure II.)
(1) Back up the images stored in the camera's built-in memory.
• Create an FAIS receive number folder (to ensure error-free user image management).
• Without inserting an memory card, connect the camera to the PC and check the image files in the camera on the PC.
Then copy those files to the folder described on the previous page.
• Check that the images can be viewed successfully on the PC.
(2) Return the backup image files from the PC to the camera.
• With no memory card inserted, turn the camera on and format the built-in memory.
• Using a card reader or similar device, check the memory card to be used for image file backup on your PC.
• Copy the image files from the image file backup folder on the previous page into the "DCIM\100_FUJI\" folder on the
image file backup memory card.
• Using a safe procedure, remove the image file backup memory card from your PC.
• Load the image file backup memory card into the camera.
• Select "Copy image" in the Playback menu, select all the frames in "Card -> Camera" and then copy the images.
• Remove the memory card and check that the images can be viewed successfully.
• Delete the backup files (user image files) created on the PC in step (1).
3-1
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
3-2
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-4. Calibration method of pattern box
<Use the pattern box for CAMERA adjustment>
Turn on the power supply in the pattern box.
Afterwards, wait for about ten minutes so that the source of
light may stabilize.
Pattern BOX
(All white)
(1) Brightness:
900 ± 20cd/m2 (without LB140 filter)
No chart, center of pattern box
Minolta brightness meter LS-110 or equivalent
* Calibration method
Contact with the brightness meter, adjust the pattern
box brightness to 900 ± 20cd/m2.
the Web server, the decompression of the file is necessary. FxHS10/HS11 W PC Soft Ver.1.00 ZJ01775-100.zip
<Step1>
The adjustment software is downloaded from WEB, and
software is installed in the PC.
<Fig. 3-5-1> Screen
We have uploaded the “PC Adjustment Software
(ZJ01775-100.zip)” for “FxHS10/HS11 W” on our website:
(https://denhin.fujifilm.co.jp/csg_en/index.htm).
3-3
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step2>
“ZJ01775-100” is a compression of “ZIP type” file. My Computer
The “FxHS10_HS11_W” folder can be done by extracting it 3.5inch FD(A:)
by “Compression software”.
(C:)
Copy the “Fx HS10_HS11” folder to the “C” drive on the
Adjustment PC. ZJ01775-100
FxHS10_HS11_W
<Fig. 3-5-2>
My Computer
3.5inch FD(A:)
(C:)
ZJ01775-100
FxHS10_HS11_W
<Fig. 3-5-3>
3-4
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-6. Connecting to the PC for Adjustment
Connect the camera to the PC as shown in the figure.
USB
USB cable
DC COUPLER CP-04
AC Power
Adapter
3-5
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 2>
The folder copied to "C:\FxHS10_HS11_W" contains 3
folders: "SSISCAL" for image stabilization, "DSCCAL" for
camera adjustment and "Firmware", which contains the
firmware files.
* Note
Do not attempt to launch "SSISCal.exe" and "DscCalDi.
exe" at the same time or run multiple adjustment software
programs concurrently.
<Fig. 3-7-2>
<Fig. 3-7-3>
3-6
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<SSISCal.exe functions>
(1) 01 to 05: Adjustment settings
(2) Exe: Executes the adjustment selected using the radio buttons
(3) Clear: Restores the default radio button settings (01.Mechanical Central Calibration) and clears all the displayed
adjustment results
(4) OK: Closes the Window
(3)
(1)
(2)
(4)
<Fig. 3-7-4>
<DscCalDi.exe function settings>
(1) AWB: AWB Adjustment
(2) Test: ZOOM Adjustment, LENS Adjustment (INF), CMOS Defect Detection, CMOS BLACK Defect Detection, EYE sensor Adjustment
(3) Focus: LENS Adjustment (INF)
(4) Focus: LENS Adjustment (INF),ZOOM Adjustment
(5) Repair site: Repair site input
(6) Factory code: Target region setting
(7) Firmware: Firmware modification
(8) Mechanical shutter Adjustment
(7)
(1)
(3)
(8) (2)
(4)
(5) (6)
<Fig. 3-7-5>
3-7
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
USB
USB cable
DC COUPLER CP-04
AC Power
Adapter
<Step 1>
Turn the camera on the connect it the PC.
*Check that the PC recognizes the camera as a PTP connection.
3-8
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 2>
Launch DscCalDi.exe.
<Fig. 3-8-1>
<Step 3>
In the adjustment selection window, select [Firmware].
<Fig. 3-8-2>
3-9
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Fig. 3-8-3>
<Step 4>
• Procedure when FinePix HS10/HS11
Select the firmware file ((1) in Figure 3-8-4) and click the [Open] button ((2) in Figure 3-8-4).
(1)
(2)
<Fig. 3-8-4>
--> The firmware update confirmation window appears.
3-10
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 5>
Click the [Yes] button.
<Fig. 3-8-5>
--> If firmware updating is successful, the "Update Firmware: Complete" window appears on the PC and on the camera's LCD panel.
(In Windows 2000, the "Unsafe Removal of Device" window appears, but this does not indicate a problem. Simply click the [OK] button.)
<Step 6>
Click the [OK] button.
<Fig. 3-8-6>
<Step 7>
Turn the camera off.
3-11
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 1>
Turn the camera on and connect it to the PC.
*Check that the PC recognizes the camera as a PTP connection.
<Step 2>
Launch SSISCal.exe.
<Fig. 3-9-1>
<Step 3>
Select the “01. Mechanical Central Calibration” radio button and then click the [Exe] button.
<Fig. 3-9-2>
3-12
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 4>
Click [OK] button.
<Fig. 3-9-3>
<Step 5>
When you have completed adjustment, click [OK] to close the adjustment item selection window.
<Fig. 3-9-4>
3-13
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
[Note]
If the pattern box is not correctly calibrated, an error will occur
during adjustment and it will not be possible to complete the
adjustment successfully.
Also, if soiling on the diffusion plate or reflective plate in the Center
Camera
Pattern box
pattern box causes blurring of the light source, adjustment
errors may occur. The pattern box should be regularly
cleaned and checked.
<Fig. 3-10-1>
<Step 1>
Connect the camera to the PC.
*Check that the PC recognizes the camera as a PTP connection.
<Step 2>
Launch SSISCal.exe.
<Fig. 3-10-2>
3-14
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 3>
Select the “02. Shading Central Calibration” radio button and then click the [Exe] button.
<Fig. 3-10-3>
--> When adjustment ends, the adjustment results are displayed.
<Step 4>
Click [OK] button.
<Fig. 3-10-4>
<Step 5>
When you have completed adjustment, click [OK] to close the adjustment item selection window.
<Fig. 3-10-5>
--> [Shading Adjustment] ends.
3-15
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
Chart
Gyro Gain
Cross chart
Fluorescet
light stand
Camera
100 mm ± 10mm
<Fig. 3-11-1>
3-16
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 1>
WIDE setting and adjust the camera position so that the centre of the Gyro Gain Cross chart
appears in the center of the camera's LCD screen.
<Fig. 3-11-2>
<Step 2>
Connect the camera to the PC and launch DscCalDi.exe.
“03. Optical Central fine Calibration” radio button and then click the [Exe] button.
<Fig. 3-11-3>
<Step 3>
Click the [OK] button.
<Fig. 3-11-4>
3-17
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 4>
Click the [OK] appears for the display.
<Fig. 3-11-5>
3-18
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-12. Gyro Offset Adjustment
<Settings for Gyro Offset Adjustment>
Set the camera up on a flat, vibration-free surface.
[Note]
Take care not to knock or vibrate the camera or the surrounding area during adjustment. Do not place your hands on the
adjustment bench or walk around in the vicinity.
<Step 1>
Connect the camera to the PC and launch DscCalDi.exe.
<Step 2>
“04. Gyro Offset Calibration” radio button and then click the [Exe] button.
<Fig. 3-12-1>
<Step 3>
Click [OK] button.
<Fig. 3-12-2>
3-19
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 4>
Check that "OK" appears for the display.
<Fig. 3-12-3>
3-20
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-13. Gyro Gain Adjustment
<Settings for Gyro Gain Adjustment>
Camera
Vibration generator
2500±10mm
It removes.
3-21
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 1>
Position the Gyro Gain Adjustment chart and camera as shown in Fig.3-13-1.
<Step 2>
Briefly disconnect the USB cable from the camera.
<Step 3>
Manually set the zoom to the TELE setting and adjust the camera position so that the centre of the Gyro Gain Adjustment
chart3 appears in the center of the camera's LCD screen.
AC adapter
USB Cable
Vibration generator
<Step 4>
Connect the camera to the PC with the USB cable.
*Check that the PC recognizes the camera as a PTP connection.
<Step 5>
Launch SSISCal.exe.
<Fig. 3-13-2>
--> The “Image stabilization” adjustment item selection window appears.
3-22
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 6>
Select the “05. Gyro Gain Calibration” radio button and then click the [Exe] button.
<Fig. 3-13-3>
-- > The [Vibration generator vibration startup] confirmation window appears.
<Step 7>
(1) Turn on the power to the vibration generator and set the MOTOR SWITCH to ON to start the jig vibrating.
(2) Adjust the oscillation frequency until the digital display shows 50.
(3) Click the [OK] button.
<Fig. 3-13-4>
POWER
X0.1Hz
FREQUENCY
•
•
•
• MOTOR
•
FREQUENCY ADJ PUSH-ON MOTOR SWITCH
•
• (press to vibrate)
•
•
•
ADJ
POWER AC100V ~ AC240V
ON
2A
OFF
3-23
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 8>
Click [OK] button.
<Fig. 3-13-5>
<Step 9>
When you have completed adjustment, click [OK] to close the adjustment item selection window.
<Fig. 3-13-6>
3-24
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-14. Zoom Adjustment
<Settings for Zoom Adjustment>
Set the camera up on a flat, vibration-free surface.
No Subject required for this adjustment.
[Note]
Take care not to knock or vibrate the camera or the surrounding area during adjustment. Do not place your hands on the
adjustment bench or walk around in the vicinity.
<Step 1>
Turn the camera on and connect it to the PC
*Check that the PC recognizes the camera as a PTP connection.
<Step 2>
Launch DscCal.exe.
<Fig. 3-14-1>
<Step 3>
Zoom set to TELE.
Input the "1" for Cal Data, and click the "OK" button.
<Fig. 3-14-2>
--> When adjustment ends, the adjustment results are displayed.
3-25
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 4>
Click the [OK] button.
<Fig. 3-14-3>
<Step 5>
Select "Zoom Cal".
<Fig. 3-14-4>
--> When adjustment ends, the adjustment results are displayed.
<Step 6>
Click the [OK] button.
<Fig. 3-14-5>
3-26
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 7>
Zoom set to WIDE..
Input the "0" for Cal Data, and click the "OK" button.
<Fig. 3-14-6>
<Step 8 >
Click the [OK] button.
<Fig. 3-14-7>
3-27
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 9>
Select "Zoom Cal".
<Fig. 3-14-8>
--> When adjustment ends, the adjustment results are displayed.
<Step 10 >
Click the [OK] button.
<Fig. 3-14-9>
3-28
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-15. LENS Adjustment (INF)
<Settings for LENS Adjustment (INF)>
(1) Set up the Siemense star chart and conversion lens so that they are 500 ± 5 mm apart.
(2) Adjust the brightness of the chart surface so that it is between 9.0 and 12.0 EV.
Lens Holder
Attention when conversion lens is used.
Convex side : Subject side.
Plane : Camera lens side.
Lens Stand
Fluorescent
Siemense star chart
light stand
7.5mm±2.5mm
(Keep distance of 7.5mm±2.5mm at all zoom positions.)
Center
500mm±5mm
(Keep distance of 500mm±5mm at all zoom positions.)
<Fig. 3-15-1>
3-29
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 1>
Turn the camera on and connect it to the PC
*Check that the PC recognizes the camera as a PTP connection.
<Step 2>
Download the Lens Adjustment Firmware before performing adjustments.
Launch DscCal.exe.
<Fig. 3-15-2>
<Step 3>
Select the Lens Adjustment Firmware.
• Select the Lens Adjustment firmware file ((1) in Figure 3-15-2) and click the [Open] button ((2) in Figure 3-15-2).
(1)
(2)
<Fig. 3-15-3>
3-30
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 4>
The camera starts up in adjustment mode.
<Fig. 3-15-4>
<Step 5>
Zoom set to WIDE
Input the "0" for Cal Data, and click the "OK" button.
<Fig. 3-15-5>
3-31
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 6>
Click the [OK] button.
<Fig. 3-15-6>
<Step 7>
Select "Zoom Cal"
<Fig. 3-15-7>
<Step 8>
Click the [OK] button.
<Fig. 3-15-8>
3-32
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 9>
Zoom set to TELE.
Input the "1" for Cal Data, and click the "OK" button.
<Fig. 3-15-9>
<Step 10>
Click the [OK] button.
<Fig. 3-15-10>
3-33
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 11>
Select "Zoom Cal"
<Fig. 3-15-11>
<Step 12>
Click the [OK] button.
<Fig. 3-15-12>
3-34
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 13>
(Case of Z01)
Turn the zoom ring to WIDE to set the zoom position to Z01.
[Notes]
Stop zooming in the direction put out.
Set a zoom position after returning A / D value more than 100 when a zoom position was over.
<Fig. 3-15-13>
<Step 14>
Zoom set to WIDE.
(Case of Z01)
Input the "0" for Cal Data, and click the "OK" button.
[Notes]
Use combinations of zoom position and cal data(Refer to <Fig. 3-15-20>)
<Fig. 3-15-14>
3-35
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 15>
(Case of Z01)
Click the [OK] button.
<Fig. 3-15-15>
<Step 16>
(Case of Z01)
Click the [Focus] button.
<Fig. 3-15-16>
3-36
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 17>
Zoom set up it to WIDE.
Before launching adjustment mode, use the live image to position the camera in the center of the chart.
(Refer to the setting of <Fig. 3-15-17>)
Position the camera so that there is a distance of 7.5mm±2.5mm of the camera lens and the conversion lens.
Note that the camera lens should not touch the conversion lens. (Refer to the setting of <Fig. 3-15-1>)
<Step 18>
The result the confirmation of "OK"
Click the [OK] button.
[Notes]
If "Focus Result NG" appears, check the settings and carry out the adjustments again.
3-37
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 19>
(1) Adjust Step 18 from Step 13 and adjust 20 positions from WIDE to TELE.
(2) Switch Cal Data from 0 to 19 and adjust it. (Refer to the setting of <Fig. 3-15-20>)
[Notes]
Position the camera so that there is a distance of 7.5mm±2.5mm of the camera lens and the conversion lens at all zoom
positions.
<Step 20>
When the adjustment ends, F/W is returned.
*Refer to "3-21. Firmware Upgrade"
3-38
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-16. Mechanical shutter Adjustment
<Settings for Mechanical shutter Adjustment>
Before connecting the camera to the PC, position the camera in
Within 5 mm± 10mm from the lens
front of the pattern box as shown in Figure 3-16-1 with the zoom
face with the WIDE position
set to WIDE.
[Note]
If the pattern box is not correctly calibrated, an error will occur
during adjustment and it will not be possible to complete the
adjustment successfully.
Also, if soiling on the diffusion plate or reflective plate in the Center
Camera
Pattern box
pattern box causes blurring of the light source, adjustment
errors may occur. The pattern box should be regularly
cleaned and checked.
<Fig. 3-16-1>
<Step 1>
Select "Monitorl".
<Fig. 3-16-2>
3-39
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 2>
Enter the "30" to the Cal Mode. then is Click the [Ok] button.
<Fig. 3-16-3>
<Fig. 3-16-3>
<Step 3>
Click the [OK] button.
*Results is displayed with "NG", but does not have any problem.
<Fig. 3-16-4>
3-40
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-17. AWB Adjustment
<Settings used for AWB adjustment>
Before connecting the camera to the PC, position the camera
in front of the pattern box with the zoom set to TELE. Within 10 mm± 20mm from the lens
face with the TELE position
[Note]
If the pattern box is not correctly calibrated, an error will
occur during adjustment and it will not be possible to
complete the adjustment successfully.
Also, if soiling on the diffusion plate or reflective plate in the
pattern box causes blurring of the light source, adjustment Center
Camera
Pattern box
errors may occur. The pattern box should be regularly
cleaned and checked.
<Fig. 3-17-1>
<Step 1>
In the adjustment selection window, select [AWB] adjustment.
<Fig. 3-17-2>
<Step 2>
Click the [Yes] button.
<Fig. 3-17-3>
--> When adjustment ends, the adjustment results window appears.
3-41
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 3>
Click the [OK] button.
<Fig. 13-17-4>
--> AWB adjustment ends.
[Note]
If "ZOOM POSITION ERROR" appears, check the settings and carry out the adjustments again.
<Fig. 13-17-5>
3-42
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-18. CMOS Defect Detection
No Subject required for this adjustment.
<Step 1>
In the adjustment selection window, select [CCD Defect].
<Fig. 3-18-1>
--> The CCD Defect Detection confirmation window appears.
<Step 2>
Click the [Yes] button.
<Fig. 3-18-2>
3-43
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 3>
Click the [OK] button.
<Fig. 3 -18-3>
--> CMOS Defect Detection ends.
3-44
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-19. CMOS BLACK Defect Detection
<Settings used for CMOS BLACK Defect Detection >
Before connecting the camera to the PC, position the camera
in front of the pattern box with the
zoom set to TELE
Within 15 ±5mm from the lens
face with the TELE position
[Note]
If the pattern box is not correctly calibrated, an error will occur
during adjustment and it will not be possible to complete the
adjustment successfully.
Also, if soiling on the diffusion plate or reflective plate in the
pattern box causes blurring of the light source, adjustment
errors may occur. The pattern box should be regularly Center
Camera
Pattern box
cleaned and checked.
.
<Fig. 3-19-1>
<Step 1>
Connect the camera to the PC and launch DscCalDi.exe..
<Step 2>
In the adjustment selection window, select [CCD BLACK].
<Fig. 3 -19-2>
3-45
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 3>
Click the [YES] button.
<Fig. 3 -19-3>
<Fig. 3 -19-4>
--> --> CMOS BLACK Defect Detection ends.
[Note]
If "ZOOM POSITION ERROR" appears, check the settings and carry out the adjustments again.
<Fig. 3 -19-5>
3-46
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-20. EYE sensor Adjustment
<Settings used for EYE sensor Adjustment >
Set the camera up on a flat, vibration-free surface.
Setting the Gray Chart (Reflective type) in the position of 100mm±10mm from a finder.
100mm±10mm
Gray Chart(Reflective type)
150mm±5mm
<Step 1>
In the adjustment selection window, select [EYE Sensor].
<Fig. 3 -20-3>
--> When EYE Sensor adjustment ends, the adjustment results window appears.
3-47
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Step 2>
Click the [OK] button.
[Note]
[Result: 0×00000000], Other than it is NG.
<Fig. 3 -20-4>
3-48
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
3-21. Firmware Upgrade
[Note]
(1) When a firmware download is required, a FUJI SERVICE BULLETIN to that effect will be issued by FTYO/QA.
(2) Implement firmware upgrade without fail after lens adjustment
USB
USB cable
DC COUPLER CP-04
AC Power
Adapter
<Step 1>
In the adjustment selection window, select [Firmware].
<Fig. 3 -21-1>
3-49
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
<Fig. 3 -21-2>
<Step 2>
• Procedure when FinePix HS10/HS11
Select the firmware file ((1) in Figure 3-21-3) and click the [Open] button ((2) in Figure 3-21-3).
(1)
(2)
<Fig. 3 -21-3>
-->The firmware update confirmation window appears.
<Step 3>
Click the [YES] button.
<Fig. 3-21-4>
3-50
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
--> If firmware updating is successful, the "Update Firmware: Complete" window appearson the PC and on the camera's
LCDpanel.
(In Windows 2000, the "Unsafe Removal of Device" window appears, but this does not indicate a problem. Simply click the
[OK]button.)
<Step 4>
Click the [OK] button.
<Fig. 3 -21-5>
<Step 5>
Turn the camera off.
3-51
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
[Notes]
* The 3 End Setting settings are the Destination, USB ID write and Product Mode settings.
* Always specify these settings as the final step after exiting the adjustment software.
The table below shows the USB IDs written in the End Setting.
Numbers in parentheses indicate decimal values. Other values are ASCII.
Item Details
Repair Date Date information is acquired from the PC and written.
Administrator ID 01(01)
Repair Station U.S.A. 61(a) SAPPORO 30(0)
CANADA 62(b) SENDAI 31(1)
HAWAII 63(c) TOKYO 33(3)
TAIWAN 64(d) NAGOYA 34(4)
GERMANY 67(g) OSAKA 35(5)
FRANCE 68(h) FUKUOKA 38(8)
SPAIN 69(i)
ITALY 6A(j)
NETHERLANDS 6B(k)
BELGIUM 6C(l)
SWEDEN 6D(m)
SWITZERLAND 6E(n)
NORWAY 6F(o)
FINLAND 70(p)
SINGAPORE 71(q)
CHINA 74(t)
OTHER 7A(z)
Repair Serial No. A serial No. is assigned automatically and written
3-52
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 3. Adjustments
<Step 1>
In the adjustment selection window, select the repair site in the [Repair site] combo box ((1) in Fig. 3-22-1).
--> The first 14 digits of the serial number are displayed.
<Step 2>
Enter the last 6 digits of the camera's serial number in the [Serial No.] box ((2) in Fig. 3-22-1).
(2)
(3)
(1) (4)
<Fig. 3 -22-1>
<Step 3>
Click the [set] button ((3) in Fig.3-22-1) to write the data to the camera.
<Step 4>
Check the third number or letter in the serial number and select the corresponding model in the [Factory Code] combo box ((4)
in Fig. 2-22-1).
Model The last six digit of the serial number Destination code
FinePix HS10 US-model 200000 to 299999,300000 to 399999 U-FF
FinePix HS10 JP-model 000001 to 099999, 100000 to 199999 J-FF
FinePix HS10 E1-model 400000 to 499999, 500000 to 599999 E1FF
FinePix HS10 EE-model 600001 to 699999, 700000 to 799999 EEFF
FinePix HS11 CH-model 800000 to 899999, 900000 to 999999 C-FF
3-53
Confidential: FUJIFILM Service Center Use Only
3. Adjustments FinePix HS10/HS11 Service Manual
MEMO
3-54
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 4. Inspection
4. Inspection
4-1. Required Measuring Equipment
Parts number Measuring equipment Remarks
Power supply AC adapter (AC-5V), Regurated power supply
Digital voltmeter For general use
Ammeter For general use (able to measure 1mA or less)
TV Monitor TV monitor, minimum resolution 600 lines
TV Monitor(HDMI) For general use
USB Cable This is bundled to the product
AV Cable This is bundled to the product
HDMI Cable (Type A-C) For general us
CR0130900U9 DC COUPLER CP-04 Common with adjustment JIG
ZJ00580-100 POWER CABLE JIG Common with adjustment JIG
ZJ00525-100 Macro Chart Resolution confirmation
ZJ00885-100 LCD Inspection Data For LCD inspection (downloaded from WEB.)
ZJ01021-100 Face Detection Test Chart Checking face detection operation
ZPU0512-100 SD CARD ULTRA2 1GB To check SD card recording
FinePix HS10/HS11
DC COUPLER CP-04
Regurated
Digital voltmeter Ammeter Power supply
4-3. Caution
Because the BATTERY TYPE setting in inspection item "15.
Battery low check" will be changed to ALKALINE, make
a note of the user-specified BATTERY TYPE for repaired
products where the BATTERY TYPE can be checked.
After completing the inspection, always change the BATTERY
TYPE to the setting noted above.
(If the BATTERY TYPE setting does not match the batteries
actually used by the user, this will affect the number of
available shots.)
4-1
Confidential: FUJIFILM Service Center Use Only
4. Inspection FinePix HS10/HS11 Service Manual
4-2
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 4. Inspection
Preparations for adjustment Method of adjustment Measuring
Sequence Item Mode
(measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs
7 Flash operation Auto mode (1) Press the flash pop-up button to
check open the flash.
(2) Set the flash mode to Forced Flash. (2) Press the 4-way button (right)
and check that the Forced Flash
icon appears on the LCD monitor.
Press the flash lamp unit down
approximately 1 cm and check that
the Forced Flash icon appears
when the lamp is gently released.
(3) Focus on any subject and press the (3) The indicator lamp lights green ->
shutter button to take a picture. Intermittently lights orange or green
(recording) -> Turns off.
(4) The flash Pop down.
8 Command dial A mode (1) Set the mode dial to "A" mode.
check LCD-ON (2) Turn the command dial left and right. (2) Check that the command dial
operates smoothly.Check that the
aperture value changes shown
on the LCD match those on the
command dial.
9 Movie/audio Movie mode (1)Press the”● “(movie record) button. (1)Check that movie/audio recording
recording check LCD-ON begins.
(2) Press the”● “(movie record) button (2)Check that movie/audio recording
to Preservation. ends and that the data is recorded
on the SD card.
10 Movie/audio Playback (1) Set the camera to Playback mode.
playback check (2) Press the 4-way button (down) to (2) Check that the movie is played
play back the movie. back on the LCD.Check that the
sound is played back through the
speaker.
11 Playback mode Playback (1) Plug the AV cable into the camera. (1) The LCD image disappears and the
check indicator lamp lights green.
(2) Check images shot at macro (2) Where the horizontal resolution is
resolutions (manual photography). as follows: 350 TV lines or better
at the center and 300 TV lines or
better at the periphery (NTSC).
300 TV lines or better at the center
and 250 TV lines or better at the
periphery (PAL).
(3) Disconnect the AV cable from the camera.
(4) Plug the HDMI cable into the camera. (4)Connect with the monitor for the HD
television and reproduce.
(5) Disconnect the HDMI AV cable from
the camera.
12 PC connection Auto mode (1) Connect the camera to the PC with (1) Check that the PC recognizes the
checking the USB cable. camera over a PTP connection.
(2) Copy the image files in the camera (2) Check that the image files have
to a folder on the PC. been copied to the PC.
(3) Disconnect the USB cable from the
camera.
13 Erase mode check Erase (1) Select “Erase” -> “Erase all” from (1) Check that an erase message such
the menu and then press the “OK” as the following appears:
button. Japan:“ OK?”
Overseas: “ERASE ALL OK?”
China: “ OK?”
(2) Select "OK" and press the “OK” (2) Check that the recorded images
button. are erased.
(3) Turn the camera off. Disconnect the
SD card from the camera.
4-3
Confidential: FUJIFILM Service Center Use Only
4. Inspection FinePix HS10/HS11 Service Manual
4-4
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 4. Inspection
Preparations for adjustment Method of adjustment Measuring
Sequence Item Mode
(measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs
17 Checking standby Power off (1) Set the DC COUPLER CP-04 and
current POWER CABLE JIG to the camera.
(2) Set the power supply voltage. (2) 5.00V±0.05V
(3) Check the standby current when the (3) 0.5mA or less.
power is turned OFF.
18 Shipping (1) Mode dial (1) SR AUTO mode
inspection (2) SETUP frame no. (2) New: The default SETUP frame
(Inventory repairs No. setting is “Continuous”, but to
only) clear the number of frames in the
frame number memory to zero, you
should always change the setting
to “New” before turning the camera
off.
(3) Flash (3) Pop down
(4) Battery and cards not inserted. (4) Normal
(5) Internal memory (5) Check that the internal memory is
formatted.
* Excluding customers camera.
(6) Card cover (6) Closed
(7) Battery cover (7) Closed
(8) Power switch (8) Off
(9)EVF dioptric adjustmentdial (9)Center position indicator located
close to the center.
(10)Zoom position (10)Set to extreme W
(11)Jack cover (11)Closed
(12)Power off. (12)The power supply is stopped after
the camera's shutdown sequence
ends.
4-5
Confidential: FUJIFILM Service Center Use Only
4. Inspection FinePix HS10/HS11 Service Manual
MEMO
4-6
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 5. Parts List
5. Parts List 5-1. FinePix HS10
5-1-1. Packing and Accessories
5-1-1-1. US-model
Ref No. Parts No. Description Comment
A114 A101 636-141-0076 UNITARY BOX
A102 636-140-2453 REINFORCE PAD INNER BOTTOM
A103 636-138-8351 REINFORCE PAD INNER TOP
A104 636-137-7508 HDPE BAG
A115 A105 636-112-2108 POLY BAG INST
A121 * Arabic/Czech/Danish/Dutch/English/Finnish/French/
German/Greek/Hungarian/Italian/Korean/Latvian/
A113
A109 Lithuanian/Norwegian/Polish/Portugal/Russian/Slovakian/
Spanish/Swedish/Ukrainian
A106
A110
A107
A108
A102
A101
A112
N.S.=Not Supply
5-1
Confidential: FUJIFILM Service Center Use Only
5. Parts List FinePix HS10/HS11 Service Manual
5-1-1-2. E1-mode
(FinePix HS10)
A104 A111
* Arabic/Czech/Danish/Dutch/English/Finnish/French/
A120 German/Greek/Hungarian/Italian/Korean/Latvian/
Lithuanian/Norwegian/Polish/Portugal/Russian/Slovakian/
A113
A109 Spanish/Swedish/Ukrainian
A106
A110
A107
A108
A102
A101
A112
N.S.=Not Supply
5-2
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 5. Parts List
5-1-1-3. EE-mode
(FinePix HS10)
A103
* Arabic/Czech/Danish/Dutch/English/Finnish/French/
German/Greek/Hungarian/Italian/Korean/Latvian/
A104 A111 Lithuanian/Norwegian/Polish/Portugal/Russian/Slovakian/
Spanish/Swedish/Ukrainian
A118
A113
A109
A106
A110
A107
A108
A102
A101
A112
N.S.=Not Supply
5-3
Confidential: FUJIFILM Service Center Use Only
5. Parts List FinePix HS10/HS11 Service Manual
5-1-1-4. JP-mode
(FinePix HS10)
Ref No. Parts No. Description Comment
A113 A101 636-141-0069 UNITARY BOX J
A114 A102 636-140-2453 REINFORCE PAD INNER BOTTOM
A103 636-138-8351 REINFORCE PAD INNER TOP
A104 636-137-7508 HDPE BAG
A111 * Arabic/Czech/Danish/Dutch/English/Finnish/French/
A104
German/Greek/Hungarian/Italian/Korean/Latvian/
Lithuanian/Norwegian/Polish/Portugal/Russian/Slovakian/
Spanish/Swedish/Ukrainian
A109
A110 A106
A107
A108
A102
A101
A112
N.S.=Not Supply
5-4
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 5. Parts List
5-1-2. Mechanical Block1
5-1-2-1 US/E1/EE/JP-model
M228 (FinePix HS10)
Ref No. Parts No. Description Comment
M201 636-137-6754 BATTERY COVER
M202 636-137-0172 LOGO BADGE
M237 M203 636-137-1001 HOLDER TERMINAL SHOE
M204 636-137-1117 SPRING TERMINAL SHOE
M236 M205 636-137-0721 ST BUTTON
M237
M206 636-137-0493 COVER JACK
M207 636-136-6076 COMPL PWB ST-1
M222 M208 636-137-7652 MAIN PWB ASSY
M221 M209 636-137-5283 ADHESIVE CONDENS
M210 636-137-0400 HOLDER CONDENSER
M218 M233 M233 M229 M231 411-018-5008 SCR PAN PCS 1.7X6
M204
M232 411-205-7006 SCR S-TPG TIN 1.4X3
M233 A M233 411-177-6502 SCR S-TPG PAN PCS 1.7X4
M203 M234 411-180-1808 SCR S-TPG PAN PCS 1.7X6.0
M229 M234 M235 411-194-8206 SCR PAN PCS 1.7X3
M234
M233
M229
M232 M229
M202 M207
M211
M213
M210
M233
M209 M212
M208
M206
M230
M229
M201 N.S.=Not Supply
5-5
Confidential: FUJIFILM Service Center Use Only
5. Parts List FinePix HS10/HS11 Service Manual
M352 M350
M336 636-116-5402 SPRING COVER
M337 636-137-0950 HOLDER COVER CARD
M310 M351 M338 636-137-0608 COVER CARD
M339 636-090-3289 SHAFT BATT
M340 636-116-5341 TERMINAL BATTERY
5-6
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 5. Parts List
MEMO
5-7
Confidential: FUJIFILM Service Center Use Only
5. Parts List FinePix HS10/HS11 Service Manual
A106
A110
A107
A113
A108
A102
A101
A112
N.S.=Not Supply
5-8
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 5. Parts List
5-2-2. Mechanical Block1
5-2-2-1 CH-model
M228 (FinePix HS11)
Ref No. Parts No. Description Comment
M201 636-137-6754 BATTERY COVER
M202 636-137-0172 LOGO BADGE
M237 M203 636-137-1001 HOLDER TERMINAL SHOE
M204 636-137-1117 SPRING TERMINAL SHOE
M236 M205 636-137-0721 ST BUTTON
M237
M206 636-137-0493 COVER JACK
M207 636-136-6076 COMPL PWB ST-1
M222 M208 636-137-7652 MAIN PWB ASSY
M221 M209 636-137-5283 ADHESIVE CONDENS
M210 636-137-0400 HOLDER CONDENSER
M218 M233 M233 M229 M231 411-018-5008 SCR PAN PCS 1.7X6
M204
M232 411-205-7006 SCR S-TPG TIN 1.4X3
M233 A M233 411-177-6502 SCR S-TPG PAN PCS 1.7X4
M203 M234 411-180-1808 SCR S-TPG PAN PCS 1.7X6.0
M229 M234 M235 411-194-8206 SCR PAN PCS 1.7X3
M234
M233
M229
M232 M229
M202 M207
M211
M213
M210
M233
M209 M212
M208
M206
M230
M229
M201 N.S.=Not Supply
5-9
Confidential: FUJIFILM Service Center Use Only
5. Parts List FinePix HS10/HS11 Service Manual
M352 M350
M336 636-116-5402 SPRING COVER
M337 636-137-0950 HOLDER COVER CARD
M310 M351
M338 636-137-0608 COVER CARD
M339 636-090-3289 SHAFT BATT
M340 636-116-5341 TERMINAL BATTERY
5-10
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 5. Parts List
MEMO
5-11
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 5. Parts List
5-3. Electrical parts
[NOTE]
* Due to standardization, replacement in the parts list may
The components indicated by mark are critical for safety.
be different from the parts list specified in the circuit or the
When indicated parts by reference number, please include
components used on the set.
the board name.
PWB
Ref No. Parts No. Description Comment
diagram
[FUSE]
F5001 323-031-1700 FUSE F-3
F5002 323-031-1700 FUSE F-3
F5003 323-031-1700 FUSE F-3
5-11
Confidential: FUJIFILM Service Center Use Only
5. Parts List FinePix HS10/HS11 Service Manual
MEMO
5-12
Confidential: FUJIFILM Service Center Use Only
FinePix HS10/HS11 Service Manual 6. Appendix
6. Appendix
6-1. List of Related Technical Updates Issued
To ensure that after-sales srevice is performed accuratety, keep a record here of the technical updates issued that cover this
device.
Technical Update No. Date Title Details/Other
Firmware Upgrade
and Revisions to the
2010-079 15, Apr. 2010 Revised pages: P3-39 to P3-40
Adjustment Software and
Service Manual
The adjustment software
2010-207 15, Apr. 2010 revision and the service Revised pages: P3-47
manual revision
6-1
Midtown West, 7-3, Akasaka 9-chome, Minato-ku, Tokyo 107-0052, Japan