Escolar Documentos
Profissional Documentos
Cultura Documentos
| Brother
HL-1212W
Setup a Brother machine on a wireless (Wi-Fi) network using the supplied CD-ROM without a
USB cable.
This FAQ explains how to configure your Brother machine for a wireless network using the CD-ROM without a USB cable. (The computer must be on
your wireless network.)
Confirm that you have already set up your router and computer. If not, set up your network firstly.
You must know your wireless network settings of the WLAN access point/router. Check and record the Network Name (SSID: Service Set ID, ESSID:
Extended Service Set ID).
Click here to see how to find SSID from your computer.
NOTE: The screens may differ depending on operating system being used and your Brother machine.
1. Place the Brother machine as close to the network access point/router as possible with minimal obstructions.
2. Make sure your Brother machine is ON.
3. Make sure your computer is ON and you are logged on with Administrator rights.
4. Put the supplied CD-ROM into your CD-ROM drive.
Windows
Macintosh
(Macintosh)
Go to Downloads section of this website and download Full Driver & Software Package. First, follow the installation instructions
on the download page. Once the installation screen appears, follow the steps from STEP c for Macintosh users below.
(Windows)
a. The installation screen will appear automatically. If prompted, choose your model and language.
https://support.brother.com/g/b/faqend.aspx?c=ca&lang=en&prod=hl1212w_us_eu&faqid=faq00100109_003#InstallConfirm 1/6
11/3/2019 Setup a Brother machine on a wireless (Wi-Fi) network using the supplied CD-ROM without a USB cable. | Brother
b. Click Install Printer Driver.
NOTE: When the User Account Control screen appears, click Allow or Yes.
c. When the License Agreement window appears, click Yes if you agree to the License Agreement.
d. Choose Wireless Network Connection without checking Custom Install. Click Next.
f. When the Firewall/AntiVirus detected screen appears, choose Change the Firewall port settings to enable network connection and
continue with the installation. (Recommended) and then click Next. Continue to STEP 5.
https://support.brother.com/g/b/faqend.aspx?c=ca&lang=en&prod=hl1212w_us_eu&faqid=faq00100109_003#InstallConfirm 2/6
11/3/2019 Setup a Brother machine on a wireless (Wi-Fi) network using the supplied CD-ROM without a USB cable. | Brother
(Macintosh)
5. When the Wireless Device Setup screen appears, choose No, I don't have a USB cable, and then click Next.
https://support.brother.com/g/b/faqend.aspx?c=ca&lang=en&prod=hl1212w_us_eu&faqid=faq00100109_003#InstallConfirm 3/6
11/3/2019 Setup a Brother machine on a wireless (Wi-Fi) network using the supplied CD-ROM without a USB cable. | Brother
6. Confirm the message on the screen. Check the Checked and confirmed box and click Next.
7. Your Network Name (SSID, ESSID) will be displayed. Choose Yes and then click Next.
8. When the Enable Wireless screen appears, you should now enable wireless networking on the device using its control panel. Follow the steps on
the right side of the screen.
a. Press and hold the WiFi button on your machine for about 2 seconds, until the light begins to blink.
b. The WiFi button will light up when connected.
You have completed Wireless Setup on your Brother machine.
https://support.brother.com/g/b/faqend.aspx?c=ca&lang=en&prod=hl1212w_us_eu&faqid=faq00100109_003#InstallConfirm 4/6
11/3/2019 Setup a Brother machine on a wireless (Wi-Fi) network using the supplied CD-ROM without a USB cable. | Brother
9. Get back to your computer. Choose Connection: OK and click Next.
Related FAQs
Setup a Brother machine on a wireless (Wi-Fi) network using the supplied CD-ROM with a USB cable.
If your question was not answered, have you checked other FAQs?
Related Models
HL-1212W
Content Feedback
https://support.brother.com/g/b/faqend.aspx?c=ca&lang=en&prod=hl1212w_us_eu&faqid=faq00100109_003#InstallConfirm 5/6