Escolar Documentos
Profissional Documentos
Cultura Documentos
The USB-Interface might be the most distributed PC interface in the world. The usage in industry-applications
is more and more common. Let’s have a closer look to the special environmental conditions of industry
applications.
That there are real concerns regarding the robustness against EMI and ESD is written in Intel’s “High Speed
USB Platform Design Guidelines”. Intel recommends the usage of a common mode choke for EMI
suppressions and another component for protection against ESD pulses.
Würth Elektronik offers all these types of products.
The WE-CNSW common mode choke was developed for EMI suppression on high speed signal
lines
For ESD suppression the TVS diode arrays WE-TVS with very low capacitances (<2pF) or the
ESD Suppressors WE-VE (capacitances down to 0.05pF) are your preferred choice.
But for outstanding EMI behaviour it is absolutely necessary to protect the power supply (Vbus) as well. A lot of
design engineers forget this important point and wonder themselves when their product don’t pass all the tests
in EMI lab.
Two typical schematics for optimized protection of one or two USB ports are shown below:
With one TVS diode array WE-TVS you can fully protect two USB lines. All four signal lines as well as the
common power supply are well protected.
For further optimization, i.e. to filter incoming common mode noise as well as differential mode noise from USB
line, a LC filter is built with the common mode choke WE-CNSW and the capacitors.
For power supply lines very good noise suppressions can be reached with a chip bead ferrite, like the Würth
Elektronik WE-CBF series.
D+ Rt D+
D- Rt D-
Common Mode
GND
Choke
Ct Ct
Figure 2: In contrast to the shielding of the dataline no low capacitive ESD suppressor is necessary at the power
supply
Single line protection components like ESD suppressors series WE-VE also have to be connected from signal
line to GND. For power line protection it is not necessary to use a low cap ESD suppressor, you might prefer
a standard SMD varistor which can withstand higher surges and higher transient energies.
Würth Elektronik launched the TVS diodes array series called WE-TVS. These TVS diodes arrays include
three main functions:
protection against ESD pulses according to EN 61000-4-2
protection against surge pulses according to EN 61000-4-5
protection against EFT pulses according to EN 61000-4-4
WE-TVS series are high performance designed TVS diode arrays which include surge rated diodes. They are
the best choice to protect high speed data lines like USB 2.0, DVI or LAN from over-voltages. The WE-TVS
series exceeds the requirements outlined in EN 61000-4-2. Due to their ultra-low capacitance (<2.0 pF) they
are nearly invisible on the signal lines.
The ESD suppressors are special raised varistors with a low and defined intrinsic capacitance. Würth
Elektronik has three different series:
WE-VE standard series: Capacitances of 1pF to 120pF and voltages from 5V to 24V
WE-VE “ULC” series: Capacitance of 0.2pF, suitable for signal lines up to 12V
WE-VE femtoF series: Capacitance of 0.05pF and rated voltages of 6V, 14V and 26V
For the first two series are also four-fold array packages available.
There are four different TVS diode arrays and five different ESD suppressor available:
Pin I/O / VDD VDD can
Order Code Package VRWM CIN IPP VESD VCl ESD
Conf. Lines float
5 4 6 5 4 6 5 4
Pin Configuration 4
1 2 3 1 2 3 1 2 3
Which maximum capacitance can you add to your data lines to pass the eye pattern test?
For USB 2.0 line capacitances up to 5pF shouldn’t cause any trouble
Answer all these questions and you will find the most suitable part for you.
We recommend for one USB 2.0 port WE-TVS 824 011 and for two USB 2.0 ports 824 015.
Designers preferring single line components may choose WE-VE ULC 823 07 050 029 or 823 06 050 029.
After making a choice of protection element you have to ensure that your whole interface design meets the
requirements of USB specification. Therefore you can use our protection devices with a small capacitance
which is nearly invisible on the signal lines.
Figure 4: Eye pattern test without any protection component placed on two USB 2.0 differential signal lines
Figure 5: Eye pattern test with TVS diode WE-TVS 824 015
The eye pattern test shows that the WE-TVS do not disturb the USB 2.0 signal. You would get the same result
with our other here listed TVS diodes and with the ESD suppressors as well.
The following table shows the cutting edge ultra-low capacitance technology of Würth Elektronik. This new
technology enables a channel to channel capacitance which is almost invisible at normal operating conditions.
The easiest way to measure the protection level is to apply an ESD pulse to your electronic circuit with the
ESD protection device and measure the peak voltage of this ESD pulse before and after the protection device.
But this way carries out different problems.
Due to high frequency and wide range of ESD pulse (few MHz to some GHZ) high frequency refractions will
occur during the measurement. The absolute peak voltage and the spike voltages during the refractions are
an indicator for better and worse protection, but you cannot indicate the definitive clamping voltage. And by
the way, this is not a reliable and repeatable measurement!
Engineers being familiar with semiconductor products do know the TLP measuring method. The TLP
(transmission line pulsing) method is an accurate measurement system which allows - due to all
measurements are done in a 50-System - repeatable and very accurate measurements.
A defined current impulse (left) is charged into the protection component and the resulting voltage across it is
measured (middle). This procedure is repeated with increasing TLP currents. As a result you get the TLP curve
(right).
This measurement can be done for VDD and I/O pins. The lower the voltage you measure, the better is the
protection device and therewith the reliability of your electronic circuit.
Thanks to the built in snap-back technology, Würth Elektronik TVS diodes have the lowest ESD clamping
voltage on the market. Compared to competitors’ products, the WE-TVS do outperform them clearly! This you
can see with a short view at the TLP curves.
VDD vs GND TLP (Transmission Line Pulsing) I/O vs GND TLP (Transmission Line Pulsing)
18 18
16 16
14 14
TLP Current [A]
TLP Current [A]
12 12
10 10
8 8
824 015 824 015
6 6
824 001 824 001
4 4
Competitor S Competitor S
2 2
Competitor P Competitor P
0 0
0 5 10 15 20 25 30 0 5 10 15 20 25 30
TLP Voltage [V] TLP Voltage [V]
Figure 7: TLP Curve of different parts for VDD Figure 8: TLP Curve of different parts for I/O lines
The two differential signal lines (D+ and D-) are routed from connector to TVS-Diode (WE-TVS 824 011) and
via a common mode choke (WE-CNSW 744 232 090) to the USB controller as shown on the left picture below.
This results in an awesome ESD protection and EMI suppression of both data lines.
VBUS is routed like the signal line, but instead of the common mode choke a chip bead ferrite (WE-CBF
742 792 641) is used. After the chip bead you may add a capacitor and a second chip bead as well to get the
highest possible EMI suppression effect.
For very sensible IC’s and / or high reliable applications you can get an optimized ESD suppression effect if
you double contact a four-fold TVS array (WE-TVS 824 015) like shown on picture.
Designers preferring single channel components can also use the ESD Suppressors WE-VE. The connection
has to be carried out from D+ / D- to GND.
The other parts are connected in same way as above.
For an easy design of interfaces Würth Elektronik has launched a special Interface Design Kit. This design kit
includes a design guide for USB 1.0 to USB 2.0, CAN, Ethernet, VGA, DVI, RS232 and RS485 interfaces and
all the components used. These are ESD Suppressors, SMD Common Mode Chokes, Chip Bead Ferrites,
LAN Transformers and the corresponding Connectors.
In total are 35 different passive components with 235 parts and 4 evaluations boards in.
The colour scheme makes it easy to locate the suitable parts for your application. Just follow the specific
application colour and arrange your needed parts.
For each application you find a simple block schematic where you see how to place the different components
to get the best result. Try it - it’s worth each penny!!
IMPORTANT NOTICE
The Application Note is based on our knowledge and experience of typical requirements concerning these areas. It serves
as general guidance and should not be construed as a commitment for the suitability for customer applications by Würth
Elektronik eiSos GmbH & Co. KG. The information in the Application Note is subject to change without notice. This
document and parts thereof must not be reproduced or copied without written permission, and contents thereof must not
be imparted to a third party nor be used for any unauthorized purpose.
Würth Elektronik eiSos GmbH & Co. KG and its subsidiaries and affiliates (WE) are not liable for application assistance of
any kind. Customers may use WE’s assistance and product recommendations for their applications and design. The
responsibility for the applicability and use of WE Products in a particular customer design is always solely within the
authority of the customer. Due to this fact it is up to the customer to evaluate and investigate, where appropriate, and
decide whether the device with the specific product characteristics described in the product specification is valid and
suitable for the respective customer application or not.
The technical specifications are stated in the current data sheet of the products. Therefore the customers shall use the
data sheets and are cautioned to verify that data sheets are current. The current data sheets can be downloaded at
www.we-online.com. Customers shall strictly observe any product-specific notes, cautions and warnings. WE reserves the
right to make corrections, modifications, enhancements, improvements, and other changes to its products and services.
WE DOES NOT WARRANT OR REPRESENT THAT ANY LICENSE, EITHER EXPRESS OR IMPLIED, IS GRANTED
UNDER ANY PATENT RIGHT, COPYRIGHT, MASK WORK RIGHT, OR OTHER INTELLECTUAL PROPERTY RIGHT
RELATING TO ANY COMBINATION, MACHINE, OR PROCESS IN WHICH WE PRODUCTS OR SERVICES ARE USED.
INFORMATION PUBLISHED BY WE REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE A LICENSE FROM WE TO USE SUCH PRODUCTS OR SERVICES OR A WARRANTY OR
ENDORSEMENT THEREOF.
WE products are not authorized for use in safety-critical applications, or where a failure of the product is reasonably
expected to cause severe personal injury or death. Moreover, WE products are neither designed nor intended for use in
areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control,
ship control), transportation signal, disaster prevention, medical, public information network etc. Customers shall inform
WE about the intent of such usage before design-in stage. In certain customer applications requiring a very high level of
safety and in which the malfunction or failure of an electronic component could endanger human life or health, customers
must ensure that they have all necessary expertise in the safety and regulatory ramifications of their applications.
Customers acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements
concerning their products and any use of WE products in such safety-critical applications, notwithstanding any applications-
related information or support that may be provided by WE. CUSTOMERS SHALL INDEMNIFY WE AGAINST ANY
DAMAGES ARISING OUT OF THE USE OF WE PRODUCTS IN SUCH SAFETY-CRITICAL APPLICATIONS.