Escolar Documentos
Profissional Documentos
Cultura Documentos
CRT2901
GX470
AUDIO SYSTEM
HEAD UNIT
PRODUCED PIONEER MODEL
VEHICLE DESTINATION TOYOTA PARTS No. ID No.
AFTER No.
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks
-Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
2 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
SAFETY INFORMATION
- CD section precaution A
1. Before disassembling the unit, be sure to turn off the 2. To protect the pickup unit from electrostatic dis-
power. Unplugging and plugging the connectors dur- charge during servicing, take an appropriate treat-
ing power-on mode may damage the ICs inside the ment (shorting-solder) by referring to “the DISAS-
unit. SEMBLY” on page 82.
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
B
repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
FX-MG8527ZT/UC 3
5 6 7 8
1 2 3 4
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
B For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
4 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
CONTENTS
SAFETY INFORMATION......................................................................................................................................3
1. SPECIFICATIONS .............................................................................................................................................6
A
2. EXPLODED VIEWS AND PARTS LIST.............................................................................................................7
2.1 PACKING(FX-MG8527ZT-91/UC,MG8727ZT-91/UC).................................................................................7
2.2 EXTERIOR .................................................................................................................................................8
2.3 CD MECHANISM UNIT(1)........................................................................................................................10
2.4 CD MECHANISM UNIT(2)........................................................................................................................12
2.5 CASSETTE MECHANISM MODULE .......................................................................................................14
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................17
3.1 BLOCK DIAGRAM(1) ...............................................................................................................................17
3.2 BLOCK DIAGRAM(2) ...............................................................................................................................18
3.3 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) ..............................................................................20
3.4 KEYBOARD UNIT ....................................................................................................................................26
3.5 CD MECHANISM MODULE(GUIDE PAGE) .............................................................................................28
B
3.6 CASSETTE MECHANISM MODULE .......................................................................................................38
4. PCB CONNECTION DIAGRAM ......................................................................................................................40
4.1 MAIN UNIT ...............................................................................................................................................40
4.2 KEYBOARD UNIT ....................................................................................................................................44
4.3 CD MECHANISM MODULE .....................................................................................................................46
4.4 CASSETTE MECHANISM MODULE .......................................................................................................52
5. ELECTRICAL PARTS LIST .............................................................................................................................54
6. ADJUSTMENT ................................................................................................................................................64
6.1 CONNECTION DIAGRAM........................................................................................................................64
6.2 AUDIO, TUNER ADJUSTMENT ...............................................................................................................67
6.3 TEST MODE .............................................................................................................................................69
6.4 CD ADJUSTMENT ...................................................................................................................................70
C
6.5 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.....................................................72
6.6 TEST MODE(CD) .....................................................................................................................................74
6.7 AVC-LAN DIAGNOSIS MODE..................................................................................................................78
7. GENERAL INFORMATION .............................................................................................................................82
7.1 DIAGNOSIS..............................................................................................................................................82
7.1.1 DISASSEMBLY......................................................................................................................................82
7.1.2 PCB LOCATIONS ..................................................................................................................................87
7.1.3 CONNECTOR FUNCTION DESCRIPTION ..........................................................................................88
7.2 PARTS ......................................................................................................................................................89
7.2.1 IC ...........................................................................................................................................................89
7.2.2 DISPLAY ................................................................................................................................................96
7.3 EXPLANATION .........................................................................................................................................97 D
7.3.1 SYSTEM BLOCK DIAGRAM .................................................................................................................97
7.3.2 OPERATIONAL FLOW CHART .............................................................................................................98
7.4 NOTES ON SERVICING ..........................................................................................................................99
7.4.1 CLEANING ............................................................................................................................................99
7.4.2 FACTORY SETTINGS ...........................................................................................................................99
8. OPERATIONS ...............................................................................................................................................100
FX-MG8527ZT/UC 5
5 6 7 8
1 2 3 4
1. SPECIFICATIONS
General
A
Power source . . . . . 13.2V(10.5V–16.0V allowable) DC
Grounding system . . . . . . . . . . . . . . Negative type
Backup current . . . . . . . . . . . . . . . . 0.3mA or less
Dimensions . . . . . . . . . 228(W) x134(H) x194(D)mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . .2.6kg
Cassette player
Tape . . . . . . . . . . . Compact cassette tape(C30-C90)
Tape speed. . . .4.76cm/sec.(+0.14cm/sec., -0.05cm/sec.)
B Wow and flutter . . . . . . . . . . . 0.2% or less(WRMS)
Crosstalk . . . . . . . . . . . . . . . . . . . . 40dB or less
Stereo Separation . . . . . . . . . . . . . . 30dB or more
S/N . . . . . . . . . . . . . . . . . . . . . . 40dB or more
Distortion. . . . . . . . . . . . . . . . . . . . . 3% or less
CD player
System . . . . . . . . . . . . . Compact disc audio system
Usable discs . . . . . . . . . . . . . . . . . Compact disc
C Signal format . . . . . . . . .Sampling frequency : 44.1kHz
. . . . . . . . . . . . . .Number of quantization : 16;linear
S/N . . . . . . . . . . . . . . . . . . . . . . 65dB or more
Distortion. . . . . . . . . . . . . . . . . . . . 0.3% or less
FM tuner
Frequency range . . . . . . . . . . 87.75, 87.9–107.9 MHz
S/N . . . . . . . . . . . . . . . 46dB or more(54dBµ input)
Distortion. . . . . . . . . . . . . . . . . . . . 1.5% or less
D IF interference . . . . . . . . . . . . . . . . 80dB or more
Image interference . . . . . . . . . . . . . . 35dB or more
Stereo Separation . . . . . . . . . . . 25dB or more(1kHz)
AM tuner
Frequency range . . . . . . . . . . . . . . 530–1,710 kHz
S/N 20dB usable sensibility . . . . . . . . . 34dBµ or less
S/N . . . . . . . . . . . . . . . . . . . . . . 42dB or more
Distortion. . . . . . . . . . . . . . . . . . . . 1.5% or less
E IF interference . . . . . . . . . . . . . . . . 55dB or more
Image interference . . . . . . . . . . . . . . 45dB or more
6 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
E
PACKING(FX-MG8527ZT-91/UC,MG8727ZT-91/UC) SECTION PARTS LIST
Mark No. Description Part No.
* 1 Air Cap CHW1945
* 2 Air Cap CHW1948
3 Cover CEG1045
4 Polyethylene Bag CEG1174
5 Carton CHG4861
FX-MG8527ZT/UC 7
5 6 7 8
1 2 3 4
2.2 EXTERIOR
8 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
51 Button(TAPE) CAC7201 B
11 Case CNB2705
12 Sheet CNM5981 52 Button(DISC) CAC7202
13 Damper CNV6608 53 Lighting Conductor CNV6895
14 Control Unit(G2T) CWX2649 54 Holder CNV6898
15 Connector(CN601) CKS1956 55 Holder CNV6899
FX-MG8527ZT/UC 9
5 6 7 8
1 2 3 4
1
3
3 3
1
1
C 1
3
3
3
F
3
3 3
3
1
1
D 2
1
1
1 1:GEM1043
3
2:GEM1042
F 3:GEM1024
10 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
21 Steer CNC9669
22 Arm CNC9242 71 Steer CNC9235
23 Bracket CNC9403 72 Flexible PCB CNP6368
* 24 Bracket CNC9408 73 PCB Unit(SIDE) CWX2613
* 25 Lever CNC9953 74 Connector(CN12) CKS3991
* 75 Connector(CN14) CKS4404
26 Gear CNV6612
27 Holder CNV6648 76 Connector(CN13) CKS4525
28 Holder CNV6738 77 Connector(CN11) CKS4572
* 29 Chassis Unit CXB6873 78 Lever Unit CXB6883
D
* 30 Frame Unit CXB6875 * 79 Lever Unit CXB9121
* 80 Lever Unit CXB9122
* 31 Arm Unit CXB6887
32 Spring CBH2488 81 Screw JFZ20P020FMC
33 Holder Unit CXB6877 82 Washer CBF1037
34 Holder Unit CXB6884
35 Tray Unit CXB6930
41 Washer CBF1064
42 Gear CNV6610
43 Gear CNV6611
44 Motor Unit(-A)(M1) CXB9726
45 Screw JFZ20P020FMC
46 Washer YE20FUC
47 ELV Motor Assy CXB7523 F
48 Screw BMZ20P025FMC
49 Washer CBF1064
50 Holder CNC9799
FX-MG8527ZT/UC 11
5 6 7 8
1 2 3 4
2
1
B
1
1
H
C
1:GEM1043
2:GEM1042
1
1
E
12 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
B
11 Holder CNV6625
12 Rack CNV6642
13 Arm CNV6731
14 Lever CNV6736
15 Holder CNV6737
26 Gear CNV6629
27 Motor Unit(-A)(M3) CXB7517
28 Screw JFZ14P020FMC
29 Loading Mech. Assy CXB7525
D
30 Washer CBF1037
* 31 Washer CBF1075
* 32 Spring CBH2450
33 Spring CBH2452
* 34 Spring CBH2457
* 35 Spring CBH2580
* 36 Frame CNC9228
* 37 Arm CNC9229
* 38 Sheet CNM7295 E
39 Roller CNV6616
40 Collar CNV6617
* 41 Guide CNV6622
* 42 Holder CNV6636
* 43 Lever CNV6732
* 44 Lever CNV6733
45 Collar CNV6734
* 46 Holder CNV7144
47 Screw JFZ12P018FMC F
48 Washer CBF1037
* 49 Motor Unit(-C) CXB7529
50 Shaft Unit(-B) CXB7528
FX-MG8527ZT/UC 13
5 6 7 8
1 2 3 4
D
I
14 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
16 Lever ENC1543
17 Arm ENC1532
18 Frame ENC1533
19 Holder ENC1547
20 Gear ENC1535
C
21 Arm ENC1550
22 Roller ENR1040
23 Belt ENT1027
24 Collar ENV1508
25 Arm ENV1539
26 Arm ENV1540
27 Gear ENV1569
28 Gear ENV1547
29 Gear ENR1044
D
30 Worm Wheel ENV1559
31 Lever ENV1551
32 Flywheel ENV1554
33 Gathering PCB ENX1073
34 Switch(S101,S102,S103) ESG1007
35 Deck Unit EWM1043
36 Plug(CN251) CKS3540
37 Gathering PCB ENX1076
38 Motor Unit(M1) EXA1618 E
39 Motor EXM1035
40 Head Assy(HD1) EXA1594
41 Arm ENC1537
42 Screw JGZ20P025FNI
43 Bracket ENC1559
44 Chassis Unit EXA1636
45 Pinch Holder Unit EXA1608
16 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
F
PU UNIT(SERVICE)(PX1)
G PCB UNIT PCB UNIT(SIDE)
A+C,B+D,
HOLOGRAM E,F
UNIT
FO+ FOP
FOCUS ACT 16 28 28 18
TO+ TOP
TRACKING ACT 14 26 26 20
B
H PCB UNIT(M2 UNIT)
MOTOR
DRIVER CN1 CN42
SPINDLE
2
A3 19 SIN(EC)
3 A2
M 5 A1
EC 5 5 6 6 40
IC 1
BA6849FS
S41 LOAD3
1 1
LOADSW2
45
C
S11 CAMCLMP
M3 CARRIAGE 50 CN101
COP
11 11 34
M COM
12 12 35
C
M1 CAMGEAR
CGM
3
M CGP
1
S32 CAMEOK
D S31 CAMLOAD
5 5
CAMOK
CAMLOAD
11
PCB UNIT 7 7 10
LED
(LED) 8 8 12
D31 D32
D
VR11
ELVSNS
VR1 ELV SENSE 46
EREF
48
E Q22 Q21
2
CN13
LOADPHT
7
(LOAD) 1 LOADSW1
8
S22 LOAD2
LOADING
LOP
4 6
M LOM
5 5
FX-MG8527ZT/UC 17
5 6 7 8
1 2 3 4
A
FM/AM TUNER UNIT
FM/AM 1ST IF 10.7MHz MPXREF 41kHz
AMRF T51 Q51 CF51 CF52 CF53 AMDET
AMANT
28 ATT L ch TUNL
IC 2 FM MPX 6
R ch
5
AMIN
20
CN501
ANT ADJ IC1 COMP
21
MAIN ANTENNA MIXER, IF AMP, DET. LDET
LDET
18
FMANT 8
SUB ANTENNA 27 ATT
RFGND
26 FMRF 20 IC252 5 RDT
CF202 PM4009A
RBDS
DECODER 11 12
AM 2ND IF X901 IC 3
IMG ADJ EEPROM X251
450kHz 10.25MHz
FMLOCL
AMPNS
AMDET
STIND
SDBW
DGND
FMSD
DI/DO
CREQ
VDD
RF ADJ
VCC
NL1
NL2
CE2
CE1
WC
B
CK
SL
LOCH LOCL
23 25 7 17 22 10 19 14 24 11 12 15 16 8 13 2 3 4 1 9
AM NOISE CANCELER Q561
AUDIO+B
SWVDD 3 IC561 9 AM
HA12181FP
MFIX FMSD FMSD
13 Q501
5
SUB IC 501 NIN 1 COMP
6 LA1061M
MAIN
DIVERSITY
C CONTROL UNIT(G2T)
CN101 10 V+5 CN501
96 16
23 PD L-OUT 3
LOUT
3.3V - 5V CONVERTER 3V Q602
97 22
32 LD
34 3 1,2 15 VD
LRCKIN ZLRCK Q603
Q101 32 6 5,6 14 CN351
SCKIN IC504(1/2) ZSCK CD MUTE
33 IC 201 Q351
UPD63711GC TC74VHCT08AFT
Q601
16
A+C,B+D,E,F CD CONTROL IC501
SM5903BFP
5V - 3.3V CONVERTER
C 18 IC505(1/2) SHOCK PROOF BUFFER RAM
TC74VHC541FT CONTROLLER
20 DOUT,LRCK, IC507
SCKO,RADV, MSM51V17400F6TFT
SBSY
ZSENSE
SERVO EQUALIZER OUTPUT
21
9,10
SERVO DSP I/F
XSI,XSO,XSCK,XSTB,XAO,XRST,FOK,LOCK, IC504(2/2) IC505(2/2)
TSI,TSO,TSCK,TSTB,PACK,SBSY TC74VHCT08AFT TC74VHC541FT
FD,TD,SD,MD
40
8 YMDATA,
YMLD,
YMCLK
98 14 VDD
14 VD ZSENSE VCC2
74
29 9 CDMUTE
18 MUTE CONT
36 OUT1+
15 BSI,BSO,BSCK,BRXEN,BSRQ,BRST
OUT2-
37 26
OPOUT MOTOR CONTROL 10 RESET
COP 19 reset 9 10
OUT3+ 3+3ch ELV1,ELV2,ELVCONT,LD1,LD2,
COM 20 LOCONT,CG1,CG2 37 VDCONT VDCNT2
45 OUT3- DRIVER IC702 VDCONT 6 13
50
ELP 2 OUT5- IC 301 PD5748C
D 34
ELM 3 OUT5+ BD7962FM MECH. VDIN
94
VD
LOP 21 CLAMP 72 HOME2 8
35 OUT4+ CONTROLLER VDD 11
LOM 22
F CGM 34
OUT4-
OUT6+
HOME 79
LOADSW2 82
HOME
LOADSW2
CGP 35 CAMCLMP 23
OUT6- CAMCLMP
CN11 ELVSNS 91
ELVSENS
EREF 92
3 EREFF
CAMOK 21 CAMOK
1
CAMLOAD 22 CAMLOAD
LOADPHT 89 LOADPHT
LOADSW1 81 LOADSW1
TEMP VD
15 VD 17 2 CD9V
13 92
5V REGULATOR 18 1
3V REGULATOR
1 IC 302 4 IC 303
3V BA05SFP
S-818A33AUC-BGN 5 2
11
V+5
10
12 VD I DECK UNIT
E
CN252 CN353
CN251
1 4 4 AUDIO+B
FWD EQ AMP 5 TAPE+B
46
L-ch 37 Q361
38 IC251 7 CSL
5 3 3
48 REV 39 HA12216F Lch
L-ch
4
7 18 17
CN254 MUTE
9
M2
SUB M 2 MECHANISM
8 B.U
MOTOR 1 DRIVER18 20 20 BU
19
5 17 STBY 19
19
2 IC351
1 PA2020A
6 MTL
M1 CN255 8 8
5
MAIN M 8 7 10 LOAD
11
MOTOR 11
CN253
3 1 5 4 6
F CN256
3 1 5 4 6
J SENSOR UNIT Q101
REEL
SENSE
18 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
A
BALANCE TO UNBALANCE CONVERTER
LANL 7 IC201 5
TUNER NJM2068MD
SELECTOR
MIXING AMP
TUNL 2 IC401 1 2 UNBALANCE TO BALANCE CONVERTER
IC202
NJM2068MD
TC4052BF Q204
1 3 6 IC203 7 6 IC204 7
CSL NJM2068MD NJM2068MD
4
CDL 5
Q205
LDET
SELECTOR
2 UNBALANCE TO BALANCE CONVERTER
IC302
RDT 1 TC4052BF Q304
3 6 IC303 7 6 IC304 7 CN472
4 NJM2068MD NJM2068MD
5
Q305
Q865 Q867
SLD1
SWVDD
RSR+
SW1
RSR-
RSL+
B
SW2 RSL-
TX1 rmut
TX1 ADIM
FMSD
AUDIO+B
Q563(1/2) CN473
SYSTEM
FMSD 1 CONTROLLER FMB SGND GND
FMSD ISENS
IC 601(1/2) Q805 R
LDET 19 Q564(1/2) isens
ldet PD5732A R TX
DI/DO 32
PDI L TX
31
PDO BSENS
CE2 11 L ACC+B
PCE2 bsens Q806
CK 33 BU
pck mute BU+B
CE1 34 PCE1
Q563(2/2)
SL 93
SL ASENS
RDT 44 AMB
RDT asens Q807
Q564(2/2) +B ACC
BU
CN351
Q351 ILL ILL-
6 AMP ANT
AVC-LAN BUS DRIVER
TX 1 IC701 6
RX 2 HA12187FP 5
TX+ TX-
8 AVC-LAN MUTE
RESET
IPPW
MUTE
Q801 C
mute
1 IC 602 2
RESET VDD R+ R-
S-80735ANDZI
L+ L-
12 SLD GND
RESET 42
AMPW 41
FMPW CN801
15 52
XIN sysmute
53
sysmute@ ANT+B Q451
X601
75
13 bsens
XOUT 73
asens AMB
65 Q452
isens
FMB
Q453
30
TX
29 RX
RX1
21
RX2
22
IPPW
XOUT 56
LANMUTE
Q721
57
0 RESET ADIM SWVDD
VDCNT2 SYSTEM
3 CONTROLLER
A
IC 601(2/2)
PD5732A Q722 D
1 VDD 4
LAMP
VDD5V REG.
43
SYSPWR IC870 Q811
B
S-81256SGUP-DIM
3
VDD
SWVDD BU
Q645 Q870 Q813
80 55 Q812
stby SWVDD Q644
BU
3
BLIGHT A VDCONT2 B
Q809 SYSPWR Q808
BU
81 Q820 Q819
69 power
2 CD9V metal CD9V
83 Q814 AUDIO+B
71 ENC1-
CSLOAD 82 Q816
ENC1+
85
ENC2- Q818
ENC2+ 84
cdej csej
Q815 Q802
ENC2M
ENC1M
20 74
ENC2P
ENC1P
LCDBL
pwr
ILLB
E
CN901
17 23 21 22 19 20 18 14,15 9 1011
A MAIN UNIT
CDEJ CSEJ
Q901
ILLB
KEY
MATRIX
Q902
LCD901
Q903
Q905 Q907
Q904
Q908
F
B KEYBOARD UNIT
FX-MG8527ZT/UC 19
5 6 7 8
1 2 3 4
A-a A-b
Large size
SCH diagram
A-a
FM/AM ANTENNA FM/AM TUNER UNIT
FM:-24.0dBs(30%,400Hz)
1 AM:-11.7dBs(30%,400Hz)
4
5
3
2
B 5
RBDS DECODER
5
2
4 1
2 5
3
3 6
FM DIVERSITY
CD:+3.8dBs(0dB,1kHz)
NC
NC
NC
D NC
NC
C CN501
SYSTEM CONTROLLER NC
NC
NC
NC
NC
TAPE:-7.5dBs(0dB,1kHz)
I CN251
1 4
5 2
6 3
F
B CN901
A
20 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
UC FX-MG8527ZT/UC
UC/ML FX-MG8727ZT/UC
A-b
A MAIN UNIT
UNBALANCE
AUDIO TO BALANCE
SELECTOR CONVERTER
FOR AMP
SYSTEM MUTE
4
2 2
2
3 5 5
4 4
6
5
1 3 3
B
1 1
ODER
5 4 2
6 FM : -14.4dBs
3 1
AM(UC) : -14.8dBs
AM(UC/ML) : -11.5dBs
CD : -1.4dBs
TAPE : -7.5dBs
4 1
0R0(UC)
2 5
3 6 4
UNBALANCE
2 AUDIO TO BALANCE
SELECTOR CONVERTER
1 3 FOR RSA
5
SYSTEM MUTE
6
2 2
5 5
4 4
C
3 3
1 1
2
4
1
6 5
>
FM: -3.8dBs
AM: -7.7dBs
CD:+8.4dBs
TAPE: -1.8dBs
350µH
A
FX-MG8527ZT/UC 21
5 6 7 8
F
E
B
A
D
C
22
A-a A-b
UC
UC/M
A-a
A-b
FM/AM ANTENNA FM/AM TUNER UNIT
FM:-24.0dBs(30%,400Hz)
1
1
1 AM:-11.7dBs(30%,400Hz)
4
5
3
2
1
4
2
6
5
2
2
RBDS DECODER
5 4 2
6
3 1
4 1
2 5
4 1
FX-MG8527ZT/UC
2 5
3 6
3 6
3
3
FM DIVERSITY
3
4
4
CD:+3.8dBs(0dB,1kHz)
NC
C
CD:+3.8dBs(0dB,1kHz)
NC
NC
NC
NC
NC
5
5
4
C CN501
SYSTEM CONTROLLER NC
5
6
6
NC
NC
NC
NC
6
FX-MG8527ZT/UC
7
7
7
TAPE:-7.5dBs(0dB,1kHz) CN251
I
1
1 4
5 2 5
6 3
6
B CN901
8
8
A-a A-b
A-a
A-b
23
E
A
D
C
F
B
F
E
B
A
D
C
24
A-a A-b
UC FX-MG8527ZT/UC
UC/ML FX-MG8727ZT/UC
A-b
1
1
A MAIN UNIT
1
UNBALANCE
AUDIO TO BALANCE
SELECTOR CONVERTER
FOR AMP
SYSTEM MUTE
2 2
5 5
4 4
3 3
2
2
1 1
2
4 2
6 FM : -14.4dBs
1
AM(UC) : -14.8dBs
AM(UC/ML) : -11.5dBs
CD : -1.4dBs
TAPE : -7.5dBs
4 1
0R0(UC)
5
FX-MG8527ZT/UC
3 6 4
UNBALANCE
2 AUDIO TO BALANCE
SELECTOR CONVERTER
1 3 FOR RSA
5
3
3
SYSTEM MUTE
6
2 2
5 5
4 4
3 3
3
1 1
4
4
2
4
1
3
2
4
1
6 5
5
5
4
5
>
6
6
6
FX-MG8527ZT/UC
FM: -3.8dBs
AM: -7.7dBs
CD:+8.4dBs
7
TAPE: -1.8dBs
7
7
350µH
8
No differentiation is made between chip capacitors and 0.022 ← R022
discrete capacitors.
A-a A-b
A-b
25
E
A
D
C
F
B
1 2 3 4
LOAD
RDS TYPE
SEEK TRACK
UP
AM FM
SEEK TRACK
DOWN
CD EJECT
TAPE DISC
C
1 2 3 4
5 6 SCAN TEXT
B
26 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
JECT TRAF
B KEYBOARD UNIT
TYPE 5 1
PWR•VOL
2
FM
4 3
E DISC
5 1
C
4 AUDIO•TUNE
2
4 3
N TEXT
A
CN804
D
B
FX-MG8527ZT/UC 27
5 6 7 8
1 2 3 4
C-a
C S F T
@) 8 1
S
C
T
F
B F 0
PCB UNIT
(SIDE)
SL F
PCB UNIT
H (M2 UNIT) VR1 CN11 T
SL F
2 2
CN41 14 14
SL SL SL
3 3 15 15
VCC 4 4 16 16
5 5 17 17
T T T
18 18
T T T T
6 6 19 19
7 7 20 20
8 8 21 21
T SL SL
9 9 22 22
10 10 23 23
!
SL
11 11 24 24 S C
12 12 25 25
13 13 T T
14 14 26 26
F F
15 15 27 27
F F
T
16 16 28 28
T T
17 29 29
17 30 30
F
1
2
CN14
3
PU UNIT(SERVICE)(PX1) 4 3+3ch
DRIVER
5
6
D RE CN31
1
2
7
8
1
3 2 C
D WH
CAMEOK
4 3
CN13
ELEVATION MOTOR 5 4
M2 CXB7526 6 5
CAMLOAD GR
PCB UNIT 7
8
BL
S
(LED) F S 4
T
1
2
3 T
T
LOAD1 LOAD2
LOADING MOTOR 3 F C
CAMGEAR MOTOR 2 F C
M1 CXB7527
E PCB UNIT(LOAD)
C S
E SL
SIGNAL LINE
F FOCUS SERVO LINE
T TRACKING SERVO LINE
C CARRIAGE SERVO LINE
S SPINDLE SERVO LINE
C D E F G H
28 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
C-b
C CONTROL UNIT(G2T)
MUTE
SL
*
B
3.3V-5V CONVERTER
BUFFER RAM SL
% SHOCK PROOF
MEMORY
CONTROLLER
^
A
&
CN351
SL
C
5V-3.3V CONVERTER
SL
3.3V REGULATOR
5V REGULATOR
4
MECHANISM CONTROLLER
C
FX-MG8527ZT/UC 29
5 6 7 8
F
E
B
A
D
C
30
C-a
A-a C-b
C-b
1
1
@) 8 1
C-a F G H
C S F T
2
2
S
C
T
F
5
0
F
PCB UNIT(SIDE)
SL F
PCB UNIT SL F
FX-MG8527ZT/UC
1 24 PCB UNIT CD CONTROL
SPINDLE
MOTOR
LOAD3
S41 1 1
6
5 CN1 CN42
6 6
CSN1051 2 2
9
CN12
3
3
7 7 3 3
8 8 4 4
9 9 5 5
S S S
5 5 6 6
12 13
4 4 7
7
7
CSN1057 8
3 3 8
CLAMP S2
2 2 9 9
HOME S1
1 1 10 10
CSN1057 C C
11 11
C C
CRG MOTOR 12 12 SL
M3 CXB7517
1 1 13 13
CN41 L1
2 2 14 14
SL SL SL
3 3 15 15
VCC 4 4 16 16
5 5 17 17
T T T
18 18
T T T T
6 6 19 19
7 7 20 20
8 8 21 21
T SL SL
9 9 22 22
10 10 23 23
!
4
4
SL
11 11 24 24 S C
12 12 25 25
1
13 13 T T
14 14 26 26
F F
15 15 27 27
F F
T
16 16 28 28
T T
17 29 29
17 30 30
F
1
2
CN14
3
PU UNIT(SERVICE)(PX1) 4 3+3ch
5
DRIVER
6
7
D 1 8
15 15 27 27
F F
T
16 16 28 28
T T
17 29 29
17 30 30
F
1
2
CN14
3
PU UNIT(SERVICE)(PX1) 4 3+3ch
5
DRIVER
6
7
D 1 8
2 1
RE CN31 3 2 C
WH CN13
4 3
CAMEOK
ELEVATION MOTOR 5 4
5
5
M2 CXB7526 6 5
CAMLOAD GR
7
BL
PCB UNIT 8 S
(LED) F S 4
T
1
2
3 T
T
LOAD1 LOAD2
LOADING MOTOR 3 F C
2 F C
CAMGEAR MOTOR
M1 CXB7527
2
E PCB UNIT(LOAD)
C S
6
6
SL
SIGNAL LINE
F FOCUS SERVO LINE
T TRACKING SERVO LINE
C CARRIAGE SERVO LINE
S SPINDLE SERVO LINE
FX-MG8527ZT/UC
7
7
3
8
8
C-a
A-a C-b
C-a D E
C-b
31
E
A
D
C
F
B
F
E
B
A
D
C
32
C-a C-b
C-b
1
1
C CONTROL UNIT(G2T)
MUTE
2
2
SL
3.3V-5V CONVERTER
BUFFER RAM SL
FX-MG8527ZT/UC
% SHOCK PROOF
MEMORY
CONTROLLER
3
3
^
A
&
CN351
SL
5V-3.3V CONVERTER
SL
4
4
1
3.3V REGULATOR
3.3V REGULATOR
5
5
5V REGULATOR
2
MECHANISM CONTROLLER
6
6
FX-MG8527ZT/UC
7
7
3
8
8
C-a C-b
C-b
33
E
A
D
C
F
B
1 2 3 4
Note: The encircled numbers denote measuring points in the circuit diagram.
34 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
FX-MG8527ZT/UC 35
5 6 7 8
1 2 3 4
36 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
FX-MG8527ZT/UC 37
5 6 7 8
1 2 3 4
B
I DECK UNIT
CN252
R278 100K
15K 3900P
VR302
R401 C401
C310
CCP1280 Q271
R022
R1
C402
C403
R33
33K(B) 2SC4116
C302
R260
R1
100K
R276
C254 390P 13K R258
29
28
27
30
26
25
23
24
22
21
3R3K
18K
R402
270K
R262
C256
R01
Rev-L
NC
PBOUT(L)
DET(L)
EQOUT(L)
MOUT(L)
MSGV(S)
TAI(L)
NC
RAI(L)
NC
R284 0R0
R275
RL
47K
C253 390P R256 31 20
Rev-R R283 0R0 180 32
NFI(L) MSGV(R)
19 R403 910
RR RIN(L) MAOUT C405 R03
C271 R287 33 18 C404 R01
Fwd-R R282 0R0 1/50 0R0 34
RIP
IC251 MSI
17 R404
FIN(L) MSDET
C252 390P
35 16 270K
C
FR
36
GND
HA12216F VCC
15
GND MSOUT
Fwd-L R281 0R0 37 FIN(R) MSGV
14 R273
FL C251 390P 38 F/R
13 0R0
VREF
39 DOLBY B NR 120/70
12
RIN(R)
HD1 R255 R296 40 NR
11
NFI(R)
R292
HEAD ASSY
0R0
EQOUT(R)
M-OUT(R)
PBOUT(R)
180 0R0
EXA1594
DET(L)
RAI(R)
MUTE
TAI(R)
BIAS
C255
R01
TEST TAPE
NC
NC
270K
R261
R272
0R0
NCT-150
10
2
3
4
1
5
6
8
7
9
R257
(400Hz, 200nWb/m)
C301
18K
R1
R259
C309
R271
13K
18K
R1
R288
0R0
VR301
CCP1280
33K(B)
R321
0R0
D
C272 R1
0R0
0R0
R285
R286
CN251
E
MUTE
-8.24dBs(300mV)±1dB A CN353
I
38 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
M1 MOTOR UNIT
(MAIN MOTOR)
EXA1618
B
CN255 Q101
CN256 EGN1004
CN253 RSB
L102
R278 100K
GND
Q271 L101
RS
R022
2SC4116
R277 R375 0R0 mtl 70µs
100K
R276
220K S103
MCS MODE
S102
R373 0R0 load LOAD
3900P
R275 S101
C352
R355
270K
47K ESG1007x3
RS3 MCS
C405 R033
300
J
RS2 RRS
PA2020A
R362
RS1 FRS
270K
SC2 RSB
C
SC1 C
R22
NC M2
CE
MOTOR UNIT
C351 (SUB MOTOR)
VCC2 NC EXA1623
VCC SM1
NC MM
R374 0R0
R01
MECHANISM
1K
1K
1K
1K
R321
0R0
C354
R351
R353
R352
R354
DRIVER
R01
D
C353
1SS355
C356 R01
D352
C355 R1
SWITCHES: E
SENSOR UNIT
S101:LOAD SWITCH..........EJECT-PLAY
S102:MODE SWITCH............ON-OFF
S103:70µs SWITCH...............ON-OFF
The underlined indicates the switch position.
53
I J
FX-MG8527ZT/UC 39
5 6 7 8
1 2 3 4
6 5 4 3 2
SIDE B
P.C.Board Chip Part
I CN251
B CN901
A
40 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
SIDE A
FM/AM ANTENNA
B
11 12 13 14 15 16 17 18 19 20
7 8 9 10 11 12
10 9 8 7 6 5 4 3 2 1
6 5 4 3 2 1 11 12 13 14 15 16 17 18 19 20
1 2 3 4 5 6 7 8 9 10
SUB
MAIN
FRONT
A
FX-MG8527ZT/UC 41
5 6 7 8
1 2 3 4
A MAIN UNIT
A
42 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
SIDE B
A
FX-MG8527ZT/UC 43
5 6 7 8
F
E
B
A
D
C
44
B
B
1
1
KEYBOARD UNIT
4.2 KEYBOARD UNIT
CD EJECT LOAD
2
2
PWR•VOL AUDIO•TUNE
1 2 3 4 5 6 SCAN TEXT
FX-MG8527ZT/UC
3
3
4
4
SIDE A
5 6 7 8
A
CN804
B
FX-MG8527ZT/UC 45
5 6 7 8
1 2 3 4
B
A
CN351
E
F F
CN11
REFO
C
46 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
C
FX-MG8527ZT/UC 47
5 6 7 8
1 2 3 4
LOAD2
F
RE
B CN13
M 5 6
8
F
7
M2 CN14
WH
ELEVATION
CAMOK
CAMLOAD
F
LOAD1
D E
48 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
D 8
CN31
1 GR
E 2
B
3
4
M
M 5 BL
M1
LOADING
CAMGEAR
VR1
ELV SENSE
C
CN101
G E
F
FX-MG8527ZT/UC 49
5 6 7 8
1 2 3 4
A
G PCB UNIT
PU UNIT(SERVICE)(PX1)
M3 CRG
M 1 17
CN41
L1
LOAD3
B
S41 1 9
CN42
H
CN1
30
1
F
CN12
F
G
50 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
S1
HOME
S2
CLAMP
HE3
C
SPINDLE
R2 C1 R1
M
HE2
13
12
CN1
15
10
1
IC1
D
G HE1
20
CN42
R4 R3
9
24
H
FX-MG8527ZT/UC 51
5 6 7 8
1 2 3 4
A CN353
CN251
1 3 5 7 9 11 13 15 17 19
2 4 6 8 10 12 14 16 18 20
B
J CN256
D
R259
C309
R255
R257
C301
R271
C255
R261
VR301
R321
R288
Q271
Q352 E
VR301
Q271 E E
10
R296
R284 1 R278
CN252 40 11
R273
Q351
R272
5 R276
R281 R277
R275
IC251 15
IC251 R282 35
R287
R283 R404
25 C404 C405
31 20
30 21 R403 C403
R402 C402
R256 C253
R262
R258
C256
R260
R401 C401
C310
22 21
R286
R285
C272
E
R252
C252
R253
C302
C271
R354
R352
IC351 VR302
VR302 CN253
R353
R351
1 CN254 CN255
F
HEAD ASSY M2 M1
I
52 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
J SENSOR UNIT
S101
LOAD
S103
70µs
S102
L101 MODE
B
CN256
L102 6
Q101 5
REEL SENSE 4
3
2
1
I CN253
J
FX-MG8527ZT/UC 53
5 6 7 8
1 2 3 4
A
Q 722 Transistor 2SC2712
Q 801 Transistor DTC114EU
B
Unit Number:CWM8064(FX-MG8527ZT/UC) Q 802 Transistor IMX1
Q 805 Transistor DTC144TUA
Unit Number:CWM8582(FX-MG8727ZT/UC)
Unit Name:Main Unit Q 806 Transistor DTC144TUA
Q 807 Transistor DTC144TUA
MISCELLANEOUS Q 808 Transistor 2SB1184F5
Q 809 Transistor 2SB1185
Q 811 Transistor 2SB1185
IC201 IC NJM2068MD
IC202 IC TC4052BF
Q 812 Transistor 2SB1185
IC203 IC NJM2068MD
Q 813 Transistor 2SA1162
IC204 IC NJM2068MD
Q 814 Transistor 2SA1162
IC252 IC PM4009A
Q 815 Transistor IMX1
C Q 816 Transistor 2SC4081
IC302 IC TC4052BF
IC303 IC NJM2068MD
Q 818 Transistor 2SB1184F5
IC304 IC NJM2068MD
Q 819 Transistor 2SA1162
IC401 IC NJM2068MD
Q 820 Transistor IMX1
IC501 IC LA1061M
Q 822 Transistor 2SD2226K
Q 825 Transistor 2SA1162
IC561 IC HA12181FP
IC601 IC PD5732A
Q 860 Transistor 2SA1162
IC602 IC S-80735ANDZI
Q 861 Transistor DTC143EU
IC701 IC HA12187FP
Q 862 Transistor DTC144TUA
IC870 IC S-81256SGUP-DIM
Q 863 Transistor IMD3A
Q 864 Transistor DTA114EU
Q 201 Transistor DTC144EU
D
Q 202 Transistor DTC144EU
Q 865 Transistor DTA114EU
Q 203 Transistor DTC144EU
Q 866 Transistor DTA114EU
Q 204 Transistor FMG13
Q 867 Transistor DTA114EU
Q 205 Transistor FMG13
Q 870 Transistor 2SD1767
Q 882 Transistor 2SA1162
Q 301 Transistor DTC144EU
Q 302 Transistor DTC144EU
Q 884 Transistor DTC124EU
Q 303 Transistor DTC144EU
D 203 Diode HZU4R7(B2)
Q 304 Transistor FMG13
D 451 Diode DAN202K
Q 305 Transistor FMG13
D 452 Diode 1SS355
D 472 Diode MPG06G-6415G50
Q 351 Transistor IMX1
E Q 405 Transistor DTC143TU
D 473 Diode MPG06G-6415G50
Q 406 Transistor IMH3A
D 474 Diode 1SS355
Q 451 Transistor 2SB1260
D 475 Diode 1SS355
Q 452 Transistor 2SC2712
D 497 Diode UDZS20(B)
D 501 Diode 1SV241
Q 453 Transistor 2SC2712
Q 497 Transistor DTC114EU
D 502 Diode 1SV241
Q 501 Transistor IMX1
D 503 Diode DAP202K
Q 502 Transistor 2SC2712
D 504 Diode 1SS355
Q 504 Transistor 2SC2712
D 703 Diode UDZS18(B)
D 704 Diode UDZS18(B)
Q 561 Transistor 2SC2712
Q 563 Transistor IMT2A
D 801 Diode 1SS355
F Q 564 Transistor IMH1A
D 802 Diode UDZS5R6(B)
Q 644 Transistor DTC114EU
D 803 Diode RM4LFJ10
Q 645 Transistor 2SA1162
D 804 Diode 1SS355
D 805 Diode UDZS20(B)
Q 721 Transistor DTA114EU
54 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part NamePart No. Circuit Symbol and No. Part NamePart No.
R 206 RS1/16S223J
D 808 Diode HZU8R2(B2) R 207 RS1/16S223J
D 809 Diode HZU7R5(B3) R 208 RS1/16S223J A
D 810 Diode HZU8R2(B2)
D 811 Diode 1SS355 R 211 RS1/16S101J
D 812 Diode HZU7R5(B3) R 212 RS1/16S101J
R 213 RS1/16S103J
D 813 Diode 1SS355 R 214 RS1/16S103J
D 814 Diode HZU8R2(B3) R 215 RS1/16S163J
D 860 Diode HZU8R2(B3)
D 861 Diode 1SS355 R 216 RS1/16S163J
D 862 Diode 1SS355 R 217 RS1/16S163J
R 218 RS1/16S163J
D 863 Diode DAP202K R 219 RS1/16S163J
D 864 Diode 1SS355 R 220 RS1/16S163J
D 870 Diode MPG06G-6415G50 B
D 871 Diode UDZS16(B) R 221 RS1/16S103J
D 882 Diode 1SS355 R 222 RS1/16S103J
R 223 RS1/16S103J
L 251 Inductor LCTA101J2520 R 224 RS1/16S103J
L 252 Inductor LCTC100K3216 R 225 RS1/16S181J
L 351 Inductor LCTC2R2K1608
L 352 Inductor LCTC2R2K1608 R 226 RS1/16S181J
L 353 Inductor LCTC2R2K1608 R 227 RS1/16S181J
R 228 RS1/16S181J
L 354 Inductor LCTC2R2K1608 R 229 RS1/10S470J
L 355 Inductor CTF1578 R 230 RS1/10S470J
L 356 Inductor LCTC2R2K1608
L 357 Inductor CTF1306 R 231 RS1/10S470J C
L 358 Inductor CTF1306 R 232 RS1/10S470J
R 233 RS1/16S473J
L 359 Inductor CTF1306 R 234 RS1/16S473J
L 360 Inductor CTF1306 R 235 RS1/16S473J
L 361 Inductor CTF1306
L 363 Inductor LFEA4R7J R 237 RS1/16S473J
L 505 Ferri-Inductor LAU4R7K R 238 RS1/16S473J
R 239 RS1/16S473J
L 506 Coil CTB1112 R 240 RS1/16S473J
L 507 Inductor LCTC6R8K3216 R 241 RS1/16S222J
L 508 Inductor LCTC6R8K3216
L 509 Inductor LCTC6R8K3216 R 243 RS1/16S103J
L 510 Inductor LCTA561J4532 R 244 RS1/16S103J D
R 245 RS1/16S103J
L 511 Inductor LCTA4R7J2520 R 246 RS1/16S103J
L 512 Inductor LCTA1R0J2520 R 247 RS1/16S562J
L 513 Inductor LCTA1R0J2520
L 514 Inductor LCTA1R0J2520 R 248 RS1/16S562J
L 561 Inductor LCTA4R7J2520 R 249 RS1/16S562J
R 250 RS1/16S562J
L 601 Inductor LCTA100J3225 R 257 RS1/16S102J
L 801 Coil 350µH CTH1276 R 261 RS1/16S225J
CG501 Surge Protector DSP-201M-A21F
CG502 Surge Protector DSP-201M-A21F R 285 RS1/16S104J
X 251 Crystal Resonator 3.648MHz CSS1447 R 286 RS1/16S104J
R 287 RS1/16S104J E
X 601 Radiator 10.0MHz CSS1577 R 288 RS1/16S104J
VR561 Semi-fixed 10kΩ(B) CCP1396 R 313 RS1/16S103J
FU471 Fuse 5A CEK1216
FM/AM Tuner Unit CWE1630 R 314 RS1/16S103J
EF352 EMI Filter CCG1163 R 315 RS1/16S163J
R 316 RS1/16S163J
RESISTORS R 317 RS1/16S163J
R 318 RS1/16S163J
R1 RS1/16S0R0J
R2 RS1/16S0R0J R 319 RS1/16S163J
R 201 RS1/16S223J R 320 RS1/16S163J
R 202 RS1/16S223J R 321 RS1/16S103J
R 203 RS1/16S223J R 322 RS1/16S103J F
R 323 RS1/16S103J
R 204 RS1/16S223J
R 205 RS1/16S223J R 324 RS1/16S103J
R 325 RS1/16S181J
FX-MG8527ZT/UC 55
5 6 7 8
1 2 3 4
Circuit Symbol and No. Part NamePart No. Circuit Symbol and No. Part NamePart No.
R 326 RS1/16S181J R 508 RS1/16S103J
R 327 RS1/16S181J R 509 RS1/16S334J
A R 328 RS1/16S181J R 510 RS1/16S101J
Circuit Symbol and No. Part NamePart No. Circuit Symbol and No. Part NamePart No.
R 614 RS1/16S102J R 684 RS1/16S102J
R 615 RS1/16S102J R 685 RS1/16S102J
R 616 RS1/16S102J R 687 RS1/16S473J A
Circuit Symbol and No. Part NamePart No. Circuit Symbol and No. Part NamePart No.
R 861 RS1/16S103J C 260 CCSRCH471J50
R 862 RS1/16S104J C 261 CCSRCH471J50
A R 863 RS1/16S223J
C 262 CEAL4R7M35
R 865 RS1/16S103J C 263 CKSRYB473K50
R 866 RS1/16S103J C 281 CKSRYB182K50
R 867 RS1/16S472J C 282 CKSRYB182K50
R 868 RS1/16S102J C 283 CKSRYB182K50
R 869 RS1/16S102J
C 284 CKSRYB182K50
R 870 RS1/10S102J C 309 CKSRYB102K50
R 871 RS1/16S472J C 310 CKSRYB105K10
R 882 RD1/4PU121J C 319 CCSRCH220J50
R 884 RS1/16S223J C 320 CCSRCH220J50
R 886 RS1/16S472J
B C 321 CCSRCH220J50
R 888 RS1/16S473J C 322 CCSRCH220J50
C 323 4.7µF/35V CCH1016
CAPACITORS C 324 4.7µF/35V CCH1016
C 325 4.7µF/35V CCH1016
C 201 CEALNP4R7M16
C 202 CEALNP4R7M16 C 326 4.7µF/35V CCH1016
C 203 CEALNP4R7M16 C 327 CCSRCH221J50
C 204 CEALNP4R7M16 C 328 CCSRCH221J50
C 205 CCSRCH330J50 C 329 CCSRCH221J50
C 330 CCSRCH221J50
C 206 CCSRCH330J50
C 207 CCSRCH330J50 C 335 4.7µF/35V CCH1016
C C 208 CCSRCH330J50 C 336 4.7µF/35V CCH1016
C 209 CKSRYB102K50 C 337 4.7µF/35V CCH1016
C 210 CKSRYB105K10 C 338 4.7µF/35V CCH1016
C 351 CEAL4R7M35
C 215 CEALNP4R7M16
C 216 CEALNP4R7M16 C 352 CKSRYB103K50
C 217 CEALNP4R7M16 C 353 4.7µF/35V CCH1016
C 218 CEALNP4R7M16 C 354 4.7µF/35V CCH1016
C 219 CCSRCH220J50 C 355 CEAL101M10
C 356 CEAL100M16
C 220 CCSRCH220J50
C 221 CCSRCH220J50 C 357 CEAL220M10
C 222 CCSRCH220J50 C 381 CKSRYB182K50
D C 223 4.7µF/35V CCH1016 C 382 CKSRYB182K50
C 224 4.7µF/35V CCH1016 C 383 CKSRYB182K50
C 384 CKSRYB182K50
C 225 4.7µF/35V CCH1016
C 226 4.7µF/35V CCH1016 C 401 CKSRYB183K50
C 227 CCSRCH221J50 C 402 CKSRYB183K50
C 228 CCSRCH221J50 C 403 4.7µF/35V CCH1016
C 229 CCSRCH221J50 C 404 4.7µF/35V CCH1016
C 406 CKSRYB102K50
C 230 CCSRCH221J50
C 231 CKSRYB473K50 C 411 CKSRYB104K16
C 232 CEAL101M6R3 C 412 CKSRYB104K16
C 233 CKSRYB102K50 C 415 CKSRYB105K10
E C 235 4.7µF/35V CCH1016 C 416 CKSRYB105K10
C 417 CCSRCH331J50
C 236 4.7µF/35V CCH1016
C 237 4.7µF/35V CCH1016 C 418 CCSRCH331J50
C 238 4.7µF/35V CCH1016 C 421 CEAL470M6R3
C 243 CKSQYB102K50 C 480 CKSQYB102K50
C 244 CKSQYB102K50 C 492 CKSRYB473K50
C 493 CCSQCH221J50
C 245 CKSQYB102K50
C 246 CKSQYB102K50 C 494 CCSQCH221J50
C 251 CKSRYB104K16 C 497 CCSRCH221J50
C 253 CEAL220M6R3 C 503 CKSQYB103K50
C 254 CKSRYB104K16 C 504 CKSRYB222K50
F C 505 CKSRYB222K50
C 256 CCSRCH270J50
C 257 CCSRCH270J50 C 506 CKSRYB222K50
C 259 CKSRYB104K16 C 507 CKSRYB222K50
C 508 CKSRYB103K50
58 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part NamePart No. Circuit Symbol and No. Part NamePart No.
C 509 CKSRYB103K50 C 816 CKSRYB103K50
C 510 CEAL100M16 C 817 100µF/10V CCH1402
A
C 511 CKSRYB472K50 C 818 CKSRYB103K50
C 512 CEAL100M16 C 819 100µF/10V CCH1402
C 513 CKSRYB473K50 C 820 CKSRYB103K50
C 514 CEAL2R2M50 C 824 CKSRYB472K50
C 515 CKSRYB102K50 C 825 100µF/10V CCH1402
C 565
C 566
CQMA333J50
CQMA333J50
B
C 567 CQMA333J50
Unit Number:CWS1342 C
Circuit Symbol and No. Part NamePart No. Circuit Symbol and No. Part NamePart No.
IL 914 Lamp 8V 60mA CEL1740 R 964 RS1/16S102J
IL 915 Lamp 8V 60mA CEL1740 R 965 RS1/16S102J
A IL 916 Lamp 8V 60mA CEL1740 R 966 RS1/16S681J
VR901 Encoder(PWR•VOL) CSD1078 R 967 RS1/16S393J
60 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part NamePart No. Circuit Symbol and No. Part NamePart No.
D 601 Chip Diode MA151WA R 512 RS1/16S333J
L 601 Inductor CTF1295 R 513 RS1/16S473J
R 516 RS1/16S331J A
TH701 Thermistor CCX1015
X 201 Radiator 16.93MHz CSS1581 R 601 RS1/16S102J
X 701 Radiator 10.00MHz CSS1428 R 602 RS1/16S102J
R 603 RS1/16S223J
RESISTORS R 604 RS1/16S223J
R 605 RS1/16S102J
R 101 RS1/8S120J
R 102 RS1/8S100J R 606 RS1/16S681J
R 103 RS1/16S222J R 607 RS1/16S681J
R 104 RS1/16S102J R 608 RS1/16S102J
R 105 RS1/16S0R0J R 609 RAB4CQ681J
R 701 RAB4CQ104J
R 201 RS1/16S104J B
R 202 RAB4CQ681J R 702 RS1/16S222J
R 203 RS1/16S0R0J R 703 RS1/16S681J
R 204 RS1/16S0R0J R 704 RAB4CQ222J
R 205 RS1/16S103J R 705 RAB4CQ681J
R 706 RS1/16S473J
R 206 RS1/16S393J
R 207 RS1/16S0R0J R 707 RS1/16S473J
R 209 RS1/16S0R0J R 708 RS1/16S222J
R 210 RS1/16S0R0J R 709 RS1/16S222J
R 211 RS1/16S0R0J R 711 RAB4CQ104J
R 712 RS1/16S473J
R 212 RS1/16S562J
R 213 RS1/16S153J R 713 RS1/16S681J C
R 214 RS1/16S123J R 714 RS1/16S473J
R 215 RS1/16S0R0J R 715 RAB4CQ222J
R 216 RS1/16S0R0J R 716 RS1/16S103J
R 718 RS1/16S473J
R 217 RS1/16S0R0J
R 220 RS1/16S471J R 719 RS1/16S104J
R 221 RS1/16S681J R 720 RS1/16S103J
R 298 RS1/16S0R0J R 724 RS1/16S104J
R 301 RS1/16S103J R 727 RS1/16S0R0J
R 734 RS1/16S104J
R 302 RS1/16S153J
R 303 RS1/16S103J R 736 RS1/16S681J
R 304 RS1/16S103J R 739 RS1/16S473J D
R 305 RS1/16S272J R 741 RS1/16S104J
R 306 RS1/16S272J R 742 RS1/16S222J
R 743 RS1/16S681J
R 307 RS1/16S182J
R 308 RS1/16S272J R 758 RS1/16S153J
R 309 RS1/16S682J R 759 RS1/16S103J
R 310 RS1/16S822J R 760 RS1/16S433J
R 311 RS1/16S103J R 767 RS1/16S154J
R 775 RAB4CQ681J
R 312 RS1/16S681J
R 313 RS1/16S103J CAPACITORS
R 314 RS1/16S153J
R 315 RS1/16S153J C 101 CKSRYB103K25 E
R 316 RS1/16S153J C 102 CKSRYB104K25
C 103 CEVL101M10
R 317 RS1/16S103J C 104 CEVL470M6R3
R 318 RS1/16S103J C 105 CKSRYB224K16
R 319 RS1/16S102J
R 320 RS1/16S392J C 106 CKSRYB224K16
R 322 RS1/16S103J C 107 CKSRYB224K16
C 201 CKSRYB104K25
R 323 RS1/16S103J C 202 CEVL220M16
R 324 RS1/16S103J C 203 CKSRYB473K25
R 325 RS1/16S103J
R 501 RS1/16S0R0J C 204 CKSRYB182K50
R 504 RS1/16S331J C 205 CKSRYB104K25 F
C 206 CKSRYB152K50
R 508 RS1/16S472J C 207 CKSRYB224K16
R 511 RS1/16S0R0J C 208 CCSRCH180J50
FX-MG8527ZT/UC 61
5 6 7 8
1 2 3 4
Circuit Symbol and No. Part NamePart No. Circuit Symbol and No. Part NamePart No.
Unit Name:PCB Unit(LED)
C 209 CCSRCK2R0C50
A C 210 CCSRCH181J50 D 31 Chip LED CL205IRXTU
C 211 CCSRCH510J50 D 32 Chip LED CL205IRXTU
C 212 CKSRYB682K50 S 31 Spring Switch(CAMLOAD) CSN1052
C 213 CKSRYB104K25 S 32 Spring Switch(CAMEOK) CSN1052
R 31 RS1/16S0R0J
C 214 CKSRYB104K25
C 215 CKSRYB103K25
C 216
C 217
C 218
CKSRYB104K25
CKSRYB104K25
CKSRYB104K25
G
Unit Number:CWX2611
C 219 CKSRYB104K25 Unit Name:PCB Unit
C 220 CKSRYB104K25
B C 221 CEVL470M6R3 L 1 Inductor CTF1389
C 222 CKSRYB104K25 S 41 Spring Switch(LOAD3) CSN1051
C 223 CKSRYB102K50
C 224
C 225
C 301
CKSRYB104K25
CKSRYB103K25
CEVL101M10
F
C 302 CKSRYB224K16
Unit Number:CWX2613
C 303 CKSRYB224K16 Unit Name:PCB Unit(Side)
C 304 10µF/10V CCH1349 MISCELLANEOUS
C 305 CKSRYB224K16
C 306 10µF/10V CCH1349 S 11 Spring Switch(CAMCLMP) CSN1052
C C 307 CKSRYB224K16 VR11 Semi-fixed 1kΩ(B) CCP1338
C 309 CKSYB475K16
RESISTORS
C 501 CKSRYB102K50
C 502 CKSRYB104K25 R 11 RS1/16S562J
C 503 CKSRYB104K25 R 12 RS1/16S562J
C 505 CKSRYB104K25 R 13 RS1/10S391J
C 506 CKSRYB104K25 R 14 RS1/10S391J
R 15 RS1/16S0R0J
C 508 CKSRYB104K25
C 509 CKSRYB104K25 R 16 RS1/16S0R0J
C 601 CEVL220M6R3
C 602 CEVL220M6R3
C 701 CKSRYB104K25
CAPACITORS
D
C 12 CKSRYB104K25
C 702 CKSRYB104K25
C 703 CKSRYB103K25
H
C 704 CKSRYB103K25
C 705 CKSRYB104K25
C 706 CKSRYB104K25
Unit Number:
C 707 CKSRYB103K25 Unit Name:PCB Unit(M2 Unit)
C 708 CKSRYB473K25
MISCELLANEOUS
E E IC1
S1
IC
Switch(HOME)
BA6849FS
CSN1057
Unit Number: S2 Switch(CLAMP) CSN1057
Unit Name:PCB Unit(Load)
RESISTORS
Q 21 Photo-transistor CPT231SCTU
Q 22 Photo-transistor CPT231SCTU R1 RS1/16S221J
L 21 Inductor LCYBR15J1608 R2 RS1/16S221J
L 22 Inductor LCYBR15J1608 R3 RS1/16S4R7J
S 21 Spring Switch(LOAD1) CSN1051 R4 RS1/16S1R0J
C1 CKSRYB104K16
D
F
Unit Number:CWX2614
62 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part NamePart No. Circuit Symbol and No. Part NamePart No.
I C 255
C 256
CKSRYB103K50
CKSRYB103K50 A
Unit Number:EWM1043 C 271 CEH1R0M50
Unit Name:Deck Unit C 272 CKSRYB104K16
C 301 CKSRYB104K16
MISCELLANEOUS C 302 CKSRYB104K16
J
R 260 RS1/16S133J
R 261 RS1/16S274J
R 262 RS1/16S274J
R 271 RS1/16S183J Unit Number:EWM1041
R 272 RS1/8S0R0J Unit Name:Sensor Unit C
R 273 RS1/8S0R0J
MISCELLANEOUS
R 275 RS1/16S473J
R 276 RS1/16S104J
L 101 Inductor CTF1546
R 277 RS1/16S224J
L 102 Inductor CTF1546
R 278 RS1/16S104J
S 101 Switch(LOAD) ESG1007
S 102 Switch(MODE) ESG1007
R 281 RS1/8S0R0J
S 103 Switch(70µS) ESG1007
R 282 RS1/8S0R0J
R 283 RS1/8S0R0J
Q 101 Photo-reflector EGN1004
R 284 RS1/8S0R0J
R 285 RS1/8S0R0J
Miscellaneous Parts List D
R 286 RS1/8S0R0J
R 287 RS1/8S0R0J M1 Motor Unit(MAIN) EXA1618
R 288 RS1/8S0R0J M2 Motor Unit(SUB) EXA1623
R 292 RS1/8S0R0J HD1 Head Assy EXA1594
R 296 RS1/16S0R0J M1 Motor Unit(-A)(CAMGEAR) CXB7527
M2 Motor Unit(-B)(ELEVATION) CXB7526
R 321 RS1/8S0R0J
R 351 RS1/16S102J M3 Motor Unit(-A)(CRG) CXB7517
R 352 RS1/16S102J VR1 Variable Resistor 10kΩ CCW1023
R 353 RS1/16S102J PU Unit(Service)(PX1) CXX1569
R 354 RS1/16S102J
R 355 RS1/16S274J E
R 362 RS1/8S301J
R 373 RS1/16S0R0J
R 374 RS1/8S0R0J
R 375 RS1/16S0R0J
R 401 RS1/16S153J
R 402 RS1/16S332J
R 403 RS1/16S911J
R 404 RS1/16S274J
CAPACITORS
C 251 CKSRYB391K50 F
C 252 CKSRYB391K50
C 253 CKSRYB391K50
C 254 CKSRYB391K50
FX-MG8527ZT/UC 63
5 6 7 8
1 2 3 4
6. ADJUSTMENT
6.1 CONNECTION DIAGRAM
A
- System 1
FX-MG8527ZT/UC GM-8027ZT/E
FX-MG8727ZT/UC AMP(M/L)
H/U AMP
B
20P 25P 16P
GGD1240 GGD1169
64 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
- System 2
FX-MG8527ZT/UC
A
FX-MG8727ZT/UC
H/U
GGD1302
B
Bullet connector
(To DC Regulated Power Supply) GM-8027ZT/E
AMP(M/L)
AMP
25P 16P
Bullet connector
(To DC Regulated Power Supply)
25P 16P
GGD1240 C
Bullet connector GGD1169
SP Line
RSA Controller
24P
24P
32P 24P
FX-MG8527ZT/UC 65
5 6 7 8
1 2 3 4
- System 3
FX-MG8527ZT/UC
A FX-MG8727ZT/UC
H/U
GGD1305
B
Bullet connector
(To DC Regulated Power Supply)
GM-8027ZT/E Bullet connector
AMP(M/L) (To DC Regulated Power Supply)
AMP
25P 16P
25P 16P
C GGD1240 GGD1169 18P 10P
FR+
Bullet connector FR-
SP Line
GGD1306
24P 10P 32P
SDVD(PANA)
24P 10P 32P
20P
RSE-ECU
D
20P
20P 12P 16P
20P
E
AV Unit
16P
Rear Display(F-TEN)
16P
16P
16P
F Bullet connector
(To DC Regulated Power Supply)
66 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
GND
B
MAIN UNIT
DECK UNIT
DECK UNIT
IC601
CN251
Pin3
L-CH
R-CH
mV
Meter(1)
D
DOLBY B NR ADJUSTMENT
No. Test Tape Adjustment Point Adjustment Method
(Switch Position)
1 NCT-150 VR301(Lch),VR302(Rch) mV Meter(1) : –8.24dBm(300mV)±1dB
(400Hz,200nwb/m) (DOLBY NR Switch : OFF)
FX-MG8527ZT/UC 67
5 6 7 8
1 2 3 4
SSG
Output
FX-MG8527ZT/UC
2-signal pad AM dummy FX-MG8727ZT/UC
Noise meter
Pulse generator
(equivalent to HP8011A)
5ms
Adjustment:
1. Setting of SSG
Receiving frequency : 1,000 kHz
Percentage modulation : 30%
Modulation frequency : 400 Hz
Antenna input : 74 dBuV (EMF)
C
2. Tune a RADIO to the "1,000 kHz" with 1' condition.
3. .Mix signal with the above-mentioned pulse and
SSG' moduration OFF.
4. Variable resistance adjust noise level to a
minimam.
Adjustment point : VR561
68 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
[DISC] *2) Note that the test mode is cancelled in the system microcomputer
CD On by switching the ACC OFF and ON, but that it is not in the CD microcomputer.
CD * Use the reset function for complete cancellation of the test mode.
(*: Disc number)
FX-MG8527ZT/UC 69
5 6 7 8
1 2 3 4
6.4 CD ADJUSTMENT
1) Precautions on Adjustment 2) Description of the Test Mode
A • Turning on the Test Mode
• The unit employs a single voltage (+5V) for the regu-
lator, thus the reference potential of the signal is See page 69.
REFO (approximately 2.5V) rather than GND. • Ending the Test Mode
Inadvertent contact of REFO and GND during adjust- Apply the reset (the reset will be applied two minutes
ment can result not only in disabling normal potential after the power is turned from off).
measurement but also in exposing the pickup to • Operation of TR JUMPs (except 100TR) continues
strong impacts due to malfunctioning of the servo. after your finger has left the key. CRG, MOVE and
Therefore, you are requested to observe the following 100TR JUMP are forced to the tracking close mode as
precautions. soon as the key is released.
• Make sure that the negative probe of the measuring • Turning the power on or off resets the JUMP MODE
instrument is not connected to REFO or GND. Special to the Single TR.
B care must be exercised so that the channel 1 negative
probe may not be connected to the oscilloscope and
the channel 2 negative probe to GND. Since the
frame of the measuring instrument is usually at the
same potential as the negative probe, the frame of
the measuring instrument must be changed to float-
ing status.
When REFO is inadvertently connected to GND, you
must immediately turn off the regulator or power
supply.
• The regulator must be turned off before mounting or
dismounting filters or wiring materials.
C • You should not start adjustment or measurement
immediately after the regulator is turned on. It is rec-
ommended to run the player for approximately one
minute so that it may stabilize.
• When the test mode is turned on, various protective
functions from the software become unavailable.
Thus, you must make sure that undesirable electric or
mechanical shocks are not be given to the system.
• This model employs a photo-transistor for detecting
discs at their loading or ejection. Thus, if its outer
case is removed during repair work and internal parts
are exposed to light of strong intensity, malfunctions
D including the following can result:
∗ The eject button becomes inoperable during play.
Pressing the eject button does not eject a disc and
play is continued.
∗ Loading becomes unavailable.
If a malfunction is recognized, appropriate remedial
actions must be taken. Such actions include chang-
ing the light source position, changing the unit posi-
tion and applying a cover to the photo-transistor.
• When you press the EJECT key to eject a disc, you
must not touch any other key until the ejection is
complete.
E
• If you press the UP or DOWN for the focus search in
the test mode, you must turn the power off immedi-
ately. (Otherwise, the lens will be forced to stick to
the top or bottom, potentially resulting in the burning
of the actuator.)
70 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
A
[DISC]+[SEEK UP]
Test Mode In
[DISC]
Source CD
[TEXT] [2]
Power Off Trackig Open
TRK MIN SEC TRK
or
8x
MIN
8x
SEC
8x D
TRK MIN SEC
9x 9x 9x
FX-MG8527ZT/UC 71
5 6 7 8
1 2 3 4
• Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mecha-
nism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted
PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if
the PU unit must be changed, the grating should be checked using the procedure below.
• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
• Symptoms of Mal-adjustment :
B
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFO
• Disc • ABEX TCD-784
• Mode • TEST MODE
C CONTROL UNIT(G2T)
L.P.F.
Xch Ych
E 100kΩ
Oscilloscope
REFO 390pF
E
F
F 100kΩ
REFO 390pF
L.P.F.
D REFO
• Checking Procedure
1. In test mode, load the disc and switch the 5V regulator on.
2. Using the SEEK UP and SEEK DOWN buttons, move the PU unit to the innermost track.
3. Press key 5 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjust-
ment the display should now read "81". Press key 5 4 times. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase differ-
ence is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
E mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver-
age angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
72 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
0° 30°
45° 60°
75° 90°
FX-MG8527ZT/UC 73
5 6 7 8
1 2 3 4
A Display
PBUS TEST
[CD] or [DISC]
Source CD
B3H
Mech Test In
B TRK
Initial state
MIN SEC
72 ** **
Manual test
Select the motor you desire to move by using one of the following four keys: [1] , [2] , [5] , and [6] .
After selecting the motor, use the [SEEK UP] or [SEEK DOWN] key tomove the selected motor. While the key is being pressed, the motor will keep
moving. Track Minute Second
Display 72 01 **
74 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
- Mechanical errors
AVC-LAN
Mode Digit Code Name Descriptions error code
Waiting for disc pulled out 1,2 20 CAMRST Forced ejection Waiting for disc pulled out ERROR 3
1,2 21 WTLOAD Forced ejection Waiting for disc pulled out ERROR 3
1,2 22 EJCTON Forced ejection Waiting for disc pulled out ERROR 3
1,2 23 SEJPCK Forced ejection Waiting for disc pulled out ERROR 3
1,2 24 HLFLOAD Forced ejection Waiting for disc pulled out ERROR 3
1,2 25 DINSRDY Forced ejection Waiting for disc pulled out ERROR 3 C
1,2 26 LIFTDN LIFTUP Forced ejection Waiting for disc pulled out ERROR 3
3 The m2stat value at the original error followed by forced ejection (*3)
4 The LOAD SW value (3 bits) at the forced ejection end:
CAM Err 1,2 51 MFWDTO CAM motor FWD time-out error during TRAY UP operation ERROR 3
1,2 52 MREVTO CAM motor REV time-out error during TRAY UP operation ERROR 3
1,2 5a MFWDTO CAM motor FWD time-out error during TRAY DN operation ERROR 3
1,2 5b MREVTO CAM motor REV time-out error during TRAY DN operation ERROR 3
1,2 5e MFWD2TO CAM motor FWD2 time-out error during TRAY DN operation ERROR 3
1,2 61 MFWDTO CAM motor FWD time-out error during CRG OUT operation ERROR 3
1,2 62 MREVTO CAM motor REV time-out error during CRG OUT operation ERROR 3
1,2 64 MLSWNG LOAD SW ON stuck error during CRG OUT operation ERROR 3
1,2 66 MREV2TO CAM motor REV2 time-out error during CRG OUT operation ERROR 3 D
1,2 6a MFWDTO CAM motor FWD time-out error during CRG IN operation ERROR 3
1,2 6b MREVTO CAM motor REV time-out error during CRG IN operation ERROR 3
1,2 71 MFWDTO CAM motor FWD time-out error during ELV IN operation ERROR 3
1,2 72 MREVTO CAM motor REV time-out error during ELV IN operation ERROR 3
1,2 7a MFWDTO CAM motor FWD time-out error during ELV OUT operation ERROR 3
1,2 7b MREVTO CAM motor REV time-out error during ELV OUT operation ERROR 3
1,2 7d MLSWNG LOAD SW ON stuck error during ELV OUT operation ERROR 3
1,2 7f MREV2TO CAM motor REV2 time-out error during ELV OUT operation ERROR 3
1,2 81 MFWDTO CAM motor FWD time-out error during EIN_EXP operation ERROR 3
1,2 82 MREVTO CAM motor REV time-out error during EIN_EXP operation ERROR 3
1,2 8a MFWDTO CAM motor FWD time-out error during CIN_EXP operation ERROR 3 E
1,2 8b MREVTO CAM motor REV time-out error during CIN_EXP operation ERROR 3
1,2 aa MOVERCNT CAM SW has not been determined during CAM operation (Chatter remains.) ERROR 3
3 The OK stop position at the last elevation operation (*4)
4 The CAM SW value (3 bits) before retry (with the first error)
CAMRST Err 1,2 91 MFWDTO ELV motor FWD time-out error during CAMRST operation ERROR 3
1,2 92 MREVTO ELV motor REV time-out error during CAMRST operation ERROR 3
1,2 93 MOVERCNT Over-count error during CAMRST operation ERROR 3
1,2 94 MSPDERR The claws do not close during CAMRST operation. ERROR 3
FX-MG8527ZT/UC 75
5 6 7 8
1 2 3 4
AVC-LAN
Mode Digit Code Name Descriptions error code
A 1,2 96 MREV2TO Overrun error during CAMRST operation ERROR 3
3 The CAM SW value (3 bits) before operation
4 The ELV stop position before operation (*5)
Claw Err 1,2 9a MSPDERR The claws do not close during DSKFREE operation. ERROR 3
1,2 9b MSPDERR The claws do not open during DSKLOCK operation. ERROR 3
1,2 9c MSPDERR The claws do not close during CLWCLSE operation. ERROR 3
1,2 9d MSPDERR The claws do not open during CLWOPEN operation. ERROR 3
3 The CAM SW value (3 bits) with the claw error
4 The CLAW SW values before and after the error stop (2 bits each)
DISCSEL Err 1,2 b1 MFWDTO ELV motor FWD time-out error during DISCSEL operation ERROR 3
1,2 b2 MREVTO ELV motor REV time-out error during DISCSEL operation ERROR 3
B 1,2 b3 MODERCNT Over-count error during DISCSEL operation ERROR 3
1,2 b6 MREV2TO Overrun error during DISCSEL DISC operation ERROR 3
3 The target disc No.
4 The ELV error stop position before retry (*5)
LIFT Err (*2) 1,2 c1 MFWDTO ELV motor FWD time-out error during LIFT UP operation ERROR 3
1,2 c2 MREVTO ELV motor REV time-out error during LIFT UP operation ERROR 3
1,2 c3 MODERCNT Over-count error during LIFT UP operation ERROR 3
1,2 c6 MREV2TO Overrun error during LIFT UP operation ERROR 3
1,2 d1 MFWDTO ELV motor FWD time-out error during LIFT DN operation ERROR 3
1,2 d2 MREVTO ELV motor REV time-out error during LIFT DN operation ERROR 3
1,2 d3 MOVERCNT Over-count error during LIFT DN operation ERROR 3
1,2 d4 MLSWNG DISC IN (SIDE SW ON) is sensed during door close operation. ERROR 3
C 1,2 d6 MREV2TO Overrun error during LIFT DN operation ERROR 3
1,2 d7 MLSW2NG "Pinched disc" is sensed during LIFT DN operation (within the range of +/-1LSB, 200ms continued) ERROR 3
3 Current disc No.
4 The ELV error stop position before retry (*5)
error ERROR 3 1,2 90 BACKUP_NG CAMRST Forced ejection Door open/close error ERROR 3
1,2 eb MLSWNG LOAD SW error during HLFLOAD operation ERROR 3
1,2 ed MLSWNG LOAD SW error during SEJPCK operation ERROR 3
1,2 fb MLSWNG LOAD SW error during DINSRDY operation ERROR 3
1,2 e0 BACKUP_NG Backup NG during EJCTON operation ERROR 3
1,2 e2 MREVTO MREVTO error during EJCTON operation ERROR 3
1,2 e6 MREV2TO MREV2TO error during EJCTON operation ERROR 3
1,2 f0 BACKUP_NG Backup NG during WTLOAD operation ERROR 3
D
1,2 f1 MFWDTO MFWDTO time-out error during WTLOAD operation ERROR 3
1,2 f2 MREVTO SIDE SW ON with OK SW ON waiting retry during WTLOAD operation ERROR 3
1,2 f3 MCHTERR Incomplete insertion error during WTLOAD operation ERROR 3
1,2 f4 MLSWNG OK SW ON but PHOTO ON during WTLOAD operation ERROR 3
1,2 f5 MFWD2TO MFWD2TO time-out error during WTLOAD operation ERROR 3
1,2 f6 MREV2TO OK SW ON waiting retry (3 times) during WTLOAD operation ERROR 3
1,2 f7 MLSW2NG SIDE SW ON at the OK SW ON waiting mode during WTLOAD operation ERROR 3
1,2 ab MOVERCNT The LOAD SW has not been determined during insertion/loading operation (Chatter remains.) ERROR 3
3 The LOAD SW value (3 bits) at the FEJCHK end
4 The ELV stop position at the FEJCHK end (*5)
New test mode 1,2 40 New test mode Focus NG after servo close ERROR 1
E 1,2 41 New test mode Lock NG after servo close ERROR 1
1,2 42 New test mode Sub code NG after servo close ERROR 1
1,2 43 New test mode Not applicable to the G2 mechanism. ERROR 1
3 The claw SW value at the occurrence of error
4 The rotation rate does not satisfy the spec.
76 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
Notes:
*1) Insertion/ejection error is output only when door open/close error occurs with forced eject.
A
*4) The last results of chatter check (compared with the target center):
+8LSB=1, +7LSB=2, +6LSB=3, +5LSB=4, +4LSB=5, +3LSB=6, +2LSB=7,
+1/0LSB=8, -1/0LSB=8,-2LSB=9, -3LSB=a, -4LSB=b, -5LSB=c, -6LSB=d, -7LSB=e, -8LSB=f,
the others=0 B
*5) Basically the value of eudpzt except for the following case:
In case of eudpzt=1 and door close mode, eudpzt=e
*6) bit0: P_lo1, bit1: P_lo2, bit2: P_elv1, bit3: P_elv2, bit4: P_cg1, bit5: P_cg2,
bit6: P_elv_vol, bit7: P_lod_vol
FX-MG8527ZT/UC 77
5 6 7 8
F
E
B
A
D
C
78
-Operations and functions
(1) Key operations
1
1
(6)Key operations
Service check mode for Memory
clearance
Diagnosis memory
Normal (2) Key operations
The physical addresses for all devices connected to the AVC-LAN (including this product) are clearance
operation for Diagnosis OUT displayed. The current and past product conditions are checked by performing the system check
mode and collecting the diagnosis memory data. Each address check result is displayed as follows: "OK", Memory clearance < From the service check mode >
automatically ends. The diagnosis memory data
"Not connected", "Check", "Replace", "Old Version" or "No response".
2
2
(6)Key operations
The diagnosis memory data for
for Memory devices selected is cleared.
Details display mode
clearance After memory clearance is
(2) Key operations
This mode is available only when the service check result is "Check", "Replace" or "Old completed, the mode is
for Diagnosis OUT Version". For each physical address, the following information is displayed: automatically shifted to the
- Logical address for the device where some failure occurs and the diagnosis codes service check mode.
(indicating details of the failure), which were obtained through system check
FX-MG8527ZT/UC
- In addition to the above data, sub-code (indicating the device with failure), connecting
confirmation no. (time stamp), and frequency of occurrence, which were obtained from
diagnosis memory data
3
3
-Key operations
(1) Diagnosis IN While pressing the CH1 and CH6 Note *1: To enter the diagnosis IN mode,
use the buttons on the head unit.
With three times of beep sound, the mode buttons simultaneously, press the
change operation completes. DISC button three times.
(2) Diagnosis OUT Keep the DISC button pressed for
1.7 seconds or more and turn the
ACC switch OFF.
(3) Entering the Service check mode. Press the TRACK UP button.
With a beep sound, the mode change completes.
(4) Entering the Details display mode. Press the CH2 button.
(5) Returning to the service check mode. Press the CH3 button.
4
4
(6)Clearing the Memory data Keep the CH5 button pressed for
1.7 seconds or more.
Change the display (forward) Press the TRACK UP button.
Change the display (backward) Press the TRACK DOWN button.
-Diagnosis mode display
Service check mode Details display mode (only in case of "Replace", "Check", or "Old Version")
After system check completes, the check results for the This mode is available only when the service check result is "Replace", "Check" or "Old Version".
5
5
devices connected to the AVC-LAN are displayed in To select this mode, press the CH2 key.
turn in order of physical address number as follows: "Physical address (for selected devices)"
"Physical address" The physical address number is displayed, whose check result details will follow it.
...The smallest physical address number is displayed Ex. P360
first, whose check result will follow it.
Ex. P190 Physical address number (CD-CH)
Physical address number "Diagnosis data source"
(radio cassette) The detailed items depend on the data source.
The physical address is displayed. Ex. SyS The data was obtained from Ex. COdE The data was obtained from diagnosis memory data.
"Check result" system check.
...The check result is displayed. "Logical address" "Logical address"...The same as that for the SyS data
6
6
Ex. good Normal (OK) The logical address number for the device "Diagnosis code"...The same as that for the SyS data
ECHn Replace with failure is displayed. "Sub code"...This code indicates the device with failure.
Details display
CHEC Check Ex. 1L_63 Ex. 1P_190
mode
OLd Old Version The sub code is displayed.
Logical address number (CD-CH)
"Physical address" The logical address is displayed. "Connecting confirmation number (when some failure
...The next physical address number is displayed. Serial number occurs)"... AVC-LAN time stamp
Ex. no01
"Diagnosis code" The connecting confirmation number (expressed in
FX-MG8527ZT/UC
"Connecting confirmation no. (current)" The diagnosis code indicates what problem occurs. the hexadecimal number system by using 00 to FF)
...The AVC-LAN time stamp is displayed. Ex. 1d_45 The connecting confirmation number is displayed.
7
7
"Frequency of occurrence"
Ex. no01 Diagnosis code (abnormal EJECT) ...The frequency of failures occurred
The connecting confirmation The diagnosis code is displayed. Ex. 1c_15
number is displayed.
The current connecting confirmation The frequency of occurrence expressed in the
number (expressed in the hexadecimal decimal number system.
number system by using 00 to FF) The frequency of occurrence is displayed.
The number increases by one each time one minute If there are two or more diagnosis codes, the diagnosis
passes. When 256 minutes pass, the indication data display will continue.
returns to 00.
8
8
79
E
A
D
C
F
B
F
E
B
A
D
C
80
_
2 Physical address allocation
_
1
0 1 2 3 4 5 6 7 8 9 A B C D E F
_
3 1
M.DISP New EMV New device device Audio ECU Audio H/U Rear TV Rear Control Multi-CD CD-CH AMP controlled
0 with AV New MM ECU
computer with AV SW decoder commander radio tuner
1
1
Europe GW
2 ECU Display
P_1_2_3
1-DIN
4 Consolidated Simple LCD Consolidated
Navigation inside panel Ex.P190
SW
Physical address
6 Gateway ECU
Europe navigation Rear TV with Navigation DISPLAY FM multiplex Fr controlled MD-CH
8 New 1-DIN TV DISP.M/U with SW commander
movie mode with controls DISPLAY SW
MONET Navigation Body
C Steering SW
ECU remote controller computer
Vehicle
E Information ECU
1,3,5,7,
9-B,D,F
_
1
0 1 2 3 4 5 6 7 8 9 A B C D E F
2
Navigation H/W H/W TEL information Camera
0 ATIS VICS TV tuner
computer CD-CH DVD-CH ECU controller
2
2
8 DVD deck
1-7,
9-F
_
1
0 1 2 3 4 5 6 7 8 9 A B C D E F
3
Radio cassette with 1DIN
0 Radio Cassette CD-P MD-P MD-CH DAT DCC
no CH controller CD-CH
TEL
8 ECU
1-7,
9-F
FX-MG8527ZT/UC
_
1
0 1 2 3 4 5 6 7 8 9 A B C D E
4 F
H/W
Equalizer DSP
3
3
0 AMP
1-F
_
1
0 1 2 3 4 5 6 7 8 9 A B C D E F
5
GPS receiver ATIS decoder FM multiplex MD-CH CD-ROM MD-ROM TEL
0 CD-CH information
decoder -CH -CH
Radio wave
8 beacon May Day
C Optical beacon
1-7,9-8,D-F
_
1
0 1 2 3 4 5 6 7 8 9 A B C D E
6 F
4
4
5
12 Abnormal MUTE 42 Tuner power supply abnormal 14 No Time updating
13 Fuse broken 43 AM tuner abnormal 15 TCXO abnormal
20 Microcomputer - abnormal 44 FM tuner abnormal 16 PLL lock abnormal
21 ROM - abnormal 45 SW tuner abnormal 40 GPS antenna abnormal
22 RAM - abnormal TV tuner 40H 10 TV tuner PLL unlocked 41 GPS antenna power supply abnormal
23 Bus - abnormal 11 FRONTEND abnormal 42 Map disc reading abnormal
24 F-ROM - abnormal 40 TV divergence shifting error 43 SPD signal abnormal
25 V-RAM - abnormal 41 TV – no reception 44 Player abnormal
26 Gate allay abnormal 42 VNR screen error 45 High temperature abnormal
27 Paint controller abnormal 43 No antenna connected FM multiplex 54H 41 Antenna power supply abnormal
28 Backup memory abnormal 44 Antenna power supply abnormal (VICS), radio 84H 45 Radio wave beacon - no antenna connected
wave beacon,
29 Voice output controller abnormal 45 SEL +B current – small beacon, optical 5BH 46 Optical beacon - no antenna connected
2A Internal power supply abnormal 46 SEL +B current – large beacon, FM 83H 47 No FM antenna connected
multiplex (data),
30 Sync signal abnormal (input) Cassette 61H 10 Belt broken 82H 4A FM receiver abnormal
and FM
31 Sync signal abnormal (output) 40 Mechanical failure or cassette broken 9AH 4B Radio wave beacon abnormal
6
6
FX-MG8527ZT/UC
DB Mode status abnormal 44 CD abnormal 54 HIT64 disconnection
DC Transmission fault 45 EJECT abnormal 55 CarNet communication not connected
DD Master reset 46 Scratches or non-recorded side 56 CarNet communication abnormal
DE Slave reset 47 CD high temperature detected 57 CarNet periodical communication abnormal
7
7
DF Master abnormal 48 Excessive current detected Information 32H 10 Video circuit abnormal
E0 Registration completion 50 Tray IN/OUT abnormal display/front 34H 11 Back light abnormal (with no current)
acknowledgement error 51 Elevator abnormal monitors 12 Back light abnormal (with excessive current)
E1 Voice processor ON abnormal 52 Clamp abnormal 13 Panel open/close mechanical operation abnormal
E2 ON/OFF command or parameter abnormal MD 64H 10 MD mech abnormal 40 Front seat monitor abnormal
E3 Registration command transmission MD-CH 65H 11 MD IN/OUT abnormal 41 Heater abnormal
E4 Multiple frames intermit. 12 MD lead-in abnormal SW, Audio 21H 10 Panel SW abnormal
FF Diagnosis - no response 40 No disc loaded SW, SW 23H 11 Touch SW failure
shifting,
41 Incorrect disc Command 24H
42 Disc unreadable SW 25H
43 MD-ROM abnormal TEL ECU, 57H 10 TEL ECU abnormal
44 MD abnormal TEL 68H 40 Communication serial lines abnormal
45 EJECT error 41 Wireless PWR lines abnormal
46 Scratches or non-recorded side
47
8
8
48 Excessive current detected
50 Tray IN/OUT abnormal
51 Elevator abnormal
52 Clamp abnormal
81
E
A
D
C
F
B
1 2 3 4
7. GENERAL INFORMATION
7.1 DIAGNOSIS
A 7.1.1 DISASSEMBLY
1
1 1
Grille Assy
Fig.1
C
1 Remove the five screws and then remove 1 1
the Frame.
1 1
Fig.2
D
E 1 1
1 1
Chassis
Fig.3
82 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
1 1
1 1
Fig.4
C
1 Straight the tabs at three locations
indicated.
1 2
D
1 1
Main Unit
Fig.5
FX-MG8527ZT/UC 83
5 6 7 8
1 2 3 4
Shorting solder
C CD Mechanism Unit
Damper Spring B
Sheet
Damper Spring A
Sheet
D
Spring B
Screw A
E Screw B
Fig.6
84 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
B
GGD1250
3
2
Control Unit(G2T)
FX-MG8527ZT/UC 85
5 6 7 8
1 2 3 4
Fig.8
Note:
To assemble the PU Unit, insert the Spring on the PU
rear between the PU Unit and the Guide first.
Fig.10
86 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
C CONTROL
(G2T)
UNIT
B A MAIN UNIT
KEYBOARD UNIT
G PCB UNIT
C
F PCB UNIT(SIDE)
H PCB UNIT(M2 UNIT)
E
PCB UNIT(LOAD)
D
PCB UNIT(LED)
J
SENSOR UNIT
I
DECK UNIT
F
FX-MG8527ZT/UC 87
5 6 7 8
1 2 3 4
SHIP
B
SUB
ANTENNA
MAIN
ANTENNA
GND NC TX+ TX- ACC BU NC NC NC SLD1 RSR+ RSR- RSL+ RSL- RMUTE ADIM ACC ILL- ANT NC TX- NC NC R- L- GND
88 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
7.2 PARTS
7.2.1 IC
A
- Pin Functions (PD5732A)
Pin No. Pin Name I/O Function and Operation
1 FMSD I Tuner : FM SD input
2 ST I Tuner : FM stereo indicator input
3 BLIGHT O Back Light ON/OFF output
4 LAMP O Lamp power supply control output
5 LDO O LCD driver : Data output
6 LDI I LCD driver : Data input
7 LCK O LCD driver : Clock output
8 BYTE I Connect to ground
9 CNVSS I Ground
10 LOCL O Tuner : Local L output B
11 PCE2 O Tuner : EEPROM chip enable output
12 reset I Reset Input
13 XOUT O Crystal oscillating element connection terminal
14 VSS GND
15 XIN I Crystal oscillating element connection terminal
16 VDD Power supply terminal
17 nmi I Connect to VDD
18 rck I RDS : Clock input
19 NC Not used
20 cdej I CD EJECT key sense input
21 RX2 I IP-BUS : Data input
22 IPPW O IP-BUS : Driver power supply output C
23 NC Not used
24 NC Not used
25 NC Not used
26 NC Not used
27 DRST O RDS : Decoder reset output
28 NC Not used
29 RX1 I IP-BUS : Data input
30 TX O IP-BUS : Data output
31 PDO O Tuner : PLL IC data output
32 PDI I Tuner : PLL IC data input
33 pck O Tuner : PLL IC clock output
34 PCE1 O Tuner : PLL IC chip select output D
35 BSO O P–BUS : Serial data output
36 BSI I P–BUS : Serial data input
37 BSCK O P-BUS : Serial clock output
38 brxen I/O P-BUS : Reception enable input/output
39 brst O P-BUS : Reset output
40 bsrq O P-BUS : Service request output
41 FMPW O FM power supply control output
42 AMPW O AM power supply control output
43 SYSPWR O System power control output
44 RDT I RDS : Data input
45 SEL1b O Amp output select b output
46 SEL1a O Amp output select a output E
47 INH1 O Amp output inhibit output (Not used)
48 SEL2b O RSE output select b output
49 SEL2a O RSE output select a output
50 INH2 O RSE output inhibit output (Not used)
51 RSEMUTE O RSE mute output
52 sysmute@ O System mute output
53 sysmute O RSE system mute output
54 ANTA O Antenna control output 0 (Not used)
55 SWVDD O Keyboard unit power supply control output
56 LANMUTE I AVC-LAN mute output
57 ADIM I ADIM information input
F
FX-MG8527ZT/UC 89
5 6 7 8
1 2 3 4
31
REF
VOL
1
1 2 3
80
GND
VIN
VOUT
81
100
90 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
SM5903BFP S-818A33AUC-BGN
33 23 VIN ON/OFF
22
5 4
34
D
VREF ON/OFF
44 12
1 11
1 2 3
E
VOUT VSS NC
FX-MG8527ZT/UC 91
5 6 7 8
1 2 3 4
92 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
* PD5748C
50
26
51 25
75 1
100
76
FX-MG8527ZT/UC 93
5 6 7 8
1 2 3 4
BA6849FS * MSM51V17400F6TFT
A
TL ras 5 22 oe
NC 4 21 FG A0-A10 : Address input
ras : Row address strobe
NC 6 21 A9
cas : Column address strobe input
B A1 5 PS 20 PS DQ1-DQ4 : Data input / output
TORQUE oe : Output enable input
SENSE AMP A10 8 we : Write enable input 19 A8
GND 6 19 EC
VCC : Power supply(3.3V)
HALL AMP
A0 9 VSS : Ground(0V) 18 A7
H1+ 7 Vcc 18 ECR
A1 10 17 A6
H1- 8 17 FR A2 11 16 A5
A3 12 15 A4
R
H2+ 9 D Q SHORT BRAKE 16 SB
VCC 13 14 VSS
CK q
C
H2- 10 15 CNF
H3+ 11 14 NC
BD7962FM
LDCONT1
OP3OUT
IN4FWD
IN4REV
OPOUT
OPIN3-
OUT6+
OUT4+
OUT3+
OUT6-
OUT4-
OUT3-
MUTE
GND1
OPIN-
VCC3
VCC2
BIAS
D
36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
CH4 CH3
CH6 F R
BIAS Vcc3 Vcc2
Control (CH5,CH6) (CH3,CH4)
logic MUTE
+ - LD
CONT1
T.S.D
LEVEL SHIFT LEVEL SHIFT
OUT5-
OUT5+
IN5FWD
IN5REV
IN6REV
IN6FWD
LDCONT2
LDCONT3
OPIN1-
OP1OUT
OPIN2-
OP2OUT
VCC1
OUT2-
OUT2+
OUT1-
OUT1+
94 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
AM 2ND IF X901 IC 3
IMG ADJ EEPROM
450kHz 10.25MHz
FMLOCL
AMPNS
AMDET
STIND
SDBW
DGND
FMSD
DI/DO
CREQ
VDD
RF ADJ
VCC
NL1
NL2
CE2
CE1
WC
CK
SL
LOCH LOCL
23 25 7 17 22 10 19 14 24 11 12 15 16 81 32 34 1 9
FX-MG8527ZT/UC 95
5 6 7 8
4 3 2 1
FX-MG8527ZT/UC 96
F
COM1
COMMON
SEGMENT
COM2
COM3
COM4
COM1
COM2
COM3
COM4
SEG1
SEG2
SEG3
SEG4
SEG5 E
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26 D
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
SEG41
SEG42
SEG43
SEG44
SEG45
SEG46
SEG47
C
SEG48
SEG49
SEG50
SEG51
SEG52
SEG53
SEG54
SEG55
SEG56
SEG57
SEG58
SEG59
SEG60
SEG61
SEG62
SEG63
SEG64
SEG65
COM4
COM3
COM2
B
COM1
COM4
COM3
COM2
COM1
A
- LCD(CAW1700)
7.2.2 DISPLAY
4 3 2 1
5 6 7 8
7.3 EXPLANATION
7.3.1 SYSTEM BLOCK DIAGRAM
A
- System 1
+B, ACC
AVC-LAN
+B, ACC
SPEAKER
L/R
FX-MG8527ZT/UC
AMPLIFIER
FX-MG8727ZT/UC AVC-LAN
PIONEER or B
OTHER MAKERS
- System 2
+B, ACC
SPEAKER
(OPTION)
REAR SEAT
L/R L/R AMPLIFIER C
HEAD L/R FX-MG8527ZT/UC
PHONE AUDIO AVC-LAN FX-MG8727ZT/UC AVC-LAN
PIONEER or
OTHER MAKERS
OTHER MAKERS
- System 3
+B, ACC
D
SPEAKER
L/R
FX-MG8527ZT/UC
AMPLIFIER
FX-MG8727ZT/UC AVC-LAN PIONEER or
OTHER MAKERS
AVC-LAN
L/R
L/R
REMOTE
L/R
RSE ECU CONTROLLER E
DVD-P AVC-LAN AVC-LAN REAR
OTHER
DISPLAY
NTSC OTHER NTSC
MAKERS MAKERS OTHER
MAKERS INFRARED
HEAD
PHONE
FX-MG8527ZT/UC 97
5 6 7 8
1 2 3 4
A
Power ON
VCC=5V
Pin 62
VDD=5V
B Pin 16
bsens
Pin 75
BSENS=L
asens
Pin 73
C
ASENS=L
SWVDD←H
Pin 55
IPPW←H
Pin 22
D SYSPWR←H
Pin 43
Source keys
operative
Source ON
E
YES
98 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:
B
Portions to be cleaned Cleaning tools
Cassette heads
Pinch rollers Cleaning paper : GED-008
Capstans
Switch ACC OFF, and then, while simultaneously pressing the "SEEK UP" (or "TUNE UP" ) and
-
-After disconnecting the power supply connector and removing this product,
-confirm that you can see a metal plate through the hole near the "SHIP"
FX-MG8527ZT/UC 99
5 6 7 8
1 2 3 4
8. OPERATIONS
A
- FX-MG8527ZT/UC
- FX-MG8727ZT/UC
100 FX-MG8527ZT/UC
1 2 3 4
5 6 7 8
- RADIO(FX-MG8527ZT/UC)
PRESET CHANNEL MEMORY
PRESET CHANNEL RECALL A
POWER/ MANUAL
VOLUME TUNING
SEEK TUNING AM FM
- CD(FX-MG8527ZT/UC)
RANDOM PLAY CD TEXT
CD EJECT REPEAT REV FF CD LOAD
POWER/
VOLUME
- CASSETTE(FX-MG8527ZT/UC)
DOLBY B NR DIRECTION CHANGE
REPEAT REW FF
POWER/
VOLUME
F
AUTO PROGRAM EJECT TAPE
SEARCH
FX-MG8527ZT/UC 101
5 6 7 8
K-ZZD.AUG. 2002 Printed in Japan