Escolar Documentos
Profissional Documentos
Cultura Documentos
MCCB Electrical Characteristics to IEC 60947-2, EN 60947-2, JIS C 8201-2-1 ANN. 1, AS/NZS 3947-2, NEMA AB-1
Electrical characteristics
Rated operational voltage Ue (V) AC 50/60 Hz 690
DC -
Rated insulation voltage Ui (V) 800
Rated impulse withstand voltage U imp (kV) 8
Ultimate breaking capacity I cu (kA) 690V AC 20
(IEC, JIS, AS/NZS) 525V AC 30
440V AC 45
400/415V AC 50
220/240V AC 85
250V DC -
Service breaking capacity I cs (kA) 690V AC 15
(IEC, JIS, AS/NZS) 525V AC 23
440V AC 34
400/415V AC 38
220/240V AC 65
250V DC -
Rated breaking capacity (NEMA) (kA) 480V AC 30
240V AC 85
Rated short-time withstand current I cw (kA) 0.3 Seconds 15
Protection
Adjustable thermal, adjustable magnetic
Fixed thermal, fixed magnetic
Microprocessor
Utilisation category B
Installation
Front connection (FC) -
Extension bar (FB)
Cable clamp (FW -
Rear connection (RC) •
Plug-in (PM) •
DIN rail mounting (DA) -
Dimensions height (mm) 370
width (mm) 3 pole 210
4 pole 280
depth (mm) 120
Weight weight (kg) 3 pole 19.8
4 pole 25.0
Operation
Direct Opening Action
Toggle operation
Door mounted (HS) / Breaker mounted handle (HB) •
Motor operation (MC) •
Endurance Electrical 690V AC
Mechanical cycles 4,000
cycles 5,000
Page 1 of 4
DATA SHEET: TEMBREAK 2 S1250-SE MCCB
Outline Dimensions S1250-SE
ASL: Arrangement Standard Line HL: Handle Frame Centre Line
Front connected
Interpole barrier 3P 4P Mounting hole 14 31 Drilling plan (front view)
3
(removable) HL 4P
ø1
HL
13 Toggle extension 3P
110
(removable)
80
HL
170
190 190
200
184
47.5
370
ASL ASL ASL ASL
95
154
140
170
78 78 28 18
Trip button (red) ø9
25
M8
Mounting screw 70
80
32 14 29
45
15
70 70 70 112
Conductor
140 105 175 overlap, max 17 120
210 280 80 171
Rear connected Drilling plan (front view) Panel cutout (front view)
M8
Mounting plate Mounting screw 4P
4P 3P
3P 3P 4P
Toggle extension Insulating plate HL HL ø9 HL HL
(removable)
12
73
184
144
226 296
120
13
101
113
258
98
20
21 140
71
114
111
19
8
154
15 32
ø13 73
45
Conductor
70 70 70 overlap, max
70 70 193
230 300
28 18 Soft plastic tubing ø50 to be provided on
center pole and neutral pole of vertical Panel cutout dimensions shown give
17 120
terminal type for insulation. ø15 for accessory wiring when necessary an allowance of 1.5mm around the
80 171
handle escutcheon.
Note: Studs are factory installed in horizontal direction both on the line and load sides.
HL HL 3P
ø1
13
Pad lock HL
80
31.5
166
79
200
184
173.5
40 102
370
117.5
Control circuit
terminal
15 32 25
80
8
M8 70
ø9
11(max.) 4.5
14 29 Mounting screw
45 70 70 70
Conductor 242.5
140 105 175 overlap, max
338(max.)
210 280
Rear connected with Motor Operator Drilling plan (front view) Panel cutout (front view)
M8 4P
Mounting plate Mounting screw 4P 3P 4P 3P
Insulating plate 3P
HL ø9 HL HL
R3
12
HL
73
184
226 296
144
113
101
90.5
19
140 3
ø1
73 71
13.5
114
154
13
15 8 20
11(max.) 4.5
111
be provided on center
242.5 18 pole and neutral pole of 230 300
vertical terminal type for 45
Panel cutout dimensions shown give
insulation. ø15 for accessory wiring when necessary
70 70 70 an allowance of 1.0mm around motor
Conductor
overlap, max operator.
Note: Studs are factory installed in horizontal direction both on the line and load sides.
Page 2 of 4
DATA SHEET: TEMBREAK 2 S1250-SE MCCB
Outline Dimensions S1250-SE Plug in Version
Plug-in
Mounting base Drilling plan (front view)
(rear view)
4P 4P
3P 3P 4P 3P
Mounting angle HL HL
HL HL
26
Toggle extension
(removable)
15
58
15
199
21
Auxiliary
40
144
circuit terminals
94
94
40
ASL ASL ASL ASL ø11
M10 Mounting 13 90 90
64
64
screw
114
147
21
169
15 32 30
15
8
45
26
140 70 70 70
ø1
145 21 70 70 70 90
3
Plug-in with Motor Operator Mounting base Drilling plan (front view)
(rear view)
M10
Mounting screw 4P
18 21 4P
3P 4P 3P
3P HL HL Mounting angle H
L
26
Max.15
HL
15
58
21
199
40
144
40
94
94
ASL ASL ASL ASL
13 Mounting angle 90 90
64
64
114
21
169
ø1
Max.15
58
1
11(max.) 4.5
Auxiliary
147
26
15 32 30
210
260.5 62 85 175 105
45
ø13 Conductor 280
70 70 70 overlap, max
HL
R3
90.5
ASL
13.5
168
Page 3 of 4
DATA SHEET: TEMBREAK 2 S1250-SE MCCB
Time/Current Characteristic Curves
S1250-SE
Percent Rated
Current In Percent Rated Current IR
In = 1250A
IR (A)
LTD Pick-up current IR xIn 0.4 0.5 0.63 0.8 0.9 0.95 1.0
Characteristics No. 1 2 3 4 5 6 7
11 21 21 5 10 19 29
LT tR (s)
at 200% x IR at 600% x IR
Standard xIR 2.5 5 10
ST
Isd
tsd (s) 0.1 0.2
INST Ii xIR 14(Max: 12 x In) Note (1)
xIR 0.8
PTA
Ip
tp (s) 40
gF Ig xIn 0.2
Option Note(3) tg (s) 0.2
xIR 1.0/0.5 Note(2)
NP
IN
tN (s) tN=tR
Note
(1) Ii max. = 12 x In. (2) 1.0 x IR or 0.5 x IR can be selected. Characteristic of neutral protection (tN vs. IN) is identical to characteristic of phase
protection (tR vs. IR). (3) When you specify gF on MCCBs with 3 poles the terminal block is automatically fitted to connect with the external neutral
CT for 3 phases 4 wires system.
Page 4 of 4