Escolar Documentos
Profissional Documentos
Cultura Documentos
2. LM-5
Product Information
Damper actuators LM
i0026809
BC
The complete range of damper actuators for general use in HVAC systems
i0084803
Type LM NM SM AM GM LF AF(R)
Torque
4 Nm 8 Nm 15 Nm 18 Nm 30 Nm 4 Nm 15 Nm
For dampers Spring return
function
– – – – –
up to approx.
For more information, please contact your Belimo Representative or order any brochures you need by fax.
Sender
Company:
Name:
Address:
Tel.: Fax:
E-Mail: Date:
2
BC Contents
Selection table
LM LM LM LM LM
Torque 4 Nm 24 24 23 23 24
-S 0 0-S -S
R
Nominal voltage AC 24 V • • •
DC 24 V • • •
AC 230 V • •
Running time 80...110 s • • • • •
Control Open/Close Single-wire • • • •
2-wire • •
Modulating DC 0...10 V •
Direction of rotation reversible (right/left) • • • • •
Manual operation by pushbutton • • • • •
Auxiliary switch potential-free • •
Mechanical angle of rotation limiting • • • •
Electronic angle of rotation limiting •
Continuous position feedback •
Damper rotation with universal spindle clamp • • • • •
Actuators with damper rotation for square form-fit spindles (8 mm), actuators with running time (25…35 s), 60 mm linear adapter and actuators
conforming to US standards on request.
LM24 4
LM24-S 4
LM230 5
LM230-S 5
Mounting instructions 6
Note
Adjusting the auxiliary switch 7
Application
The type LM24(-S) is intended for the
operation of air control dampers in venti-
lation and air-conditioning systems.
Mode of operation
Open/Close control by single-wire or
2-wire system.
p0001707
Product features
Simple direct mounting on the damper
spindle by universal spindle clamp. An
antirotation device is supplied to prevent
unwanted rotation of the whole unit.
Maintenance maintenance-free
22.1 94.1
Weight 650 g
4
BC LM230, LM230-S damper actuators 4 Nm
Application
The type LM230(-S) is intended for the
operation of air control dampers in venti-
lation and air-conditioning systems.
Mode of operation
Open/Close control by single-wire sys-
tem.
p0002707
Product features
Simple direct mounting on the damper
spindle by universal spindle clamp. An
Wiring diagram
antirotation device is supplied to prevent
N L1 AC 230 V To isolate from the main power supply, the system
must incorporate a device which disconnects the
unwanted rotation of the whole unit.
phase conductors (with at least a 3 mm contact gap).
Manual operation by self-resetting push-
button when necessary (the gearing is
disengaged while the pushbutton is held
depressed).
1 2 3 S1 S2 S3
Adjustable angle of rotation with me-
chanical stops.
0...100%
LM230-S
High functional reliability
The actuator is overload-proof, needs no
w0228803
Maintenance maintenance-free
0
5
6
6...16
m
in
.3
5
m
m
4
2
Mounting instructions LM24(-S), LM230(-S)
≈ 1 mm
2
1
3
3
5...6Nm
5
3
1
BC
m0001707
S2 S2
S1 S1
S3 S3
0 .2
.4
.6
0 1 1 .8
– Now, when the actuator rotates clockwise, the switch will operate
at 60% angle of rotation. (Connection S1 to S3 made)
Option 2: Actuator at Procedure: – Depress the manual-operation pushbutton and move the actu-
switching position ator to the position where the auxiliary switch is needed to
operate (e.g. at 60% angle of rotation).
S2 S2
S1 S1
S3 S3
0 .2
.4
.6
m0003707
1 .8
0 1
m0002707
S2 S2
S1 S1
S3 S3
0 .2
.4
.6
1 .8
0 1
Option 2: Actuator at Procedure: – Depress the manual-operation pushbutton and move the
switching position actuator to the position where the auxiliary switch is needed to
operate (e.g. at 60% angle of rotation).
S2 S2
S1 S1
S3 S3
0 .2
.4
.6
m0005707
1 .8
0 1
m0004707
– Turn the scale knob of the auxiliary switch clockwise until the tip
of the arrow is just past the 1 on the scale. (Connection S1 to S3
made and switching position set for 60% angle of rotation)
7
LM24-SR damper actuator 4 Nm BC
Dampers up to approx. 0.8 m2
Modulating damper actuator
(AC/DC 24 V)
Control DC 0…10 V and posi-
tion feedback DC 2…10 V
Application
The type LM24-SR is intended for the
operation of air control dampers in venti-
lation and air-conditioning systems.
Mode of operation
The actuator is controlled by a standard
DC 0…10 V signal and runs to whatever
position is specified by the signal. The
p0003707
purpose of measuring voltage U is to
provide 0…100% electrical indication of
damper position and to act as a master-
slave control signal for other actuators.
Product features
Wiring diagram
Simple direct mounting on the damper
w0230803
T ~ AC 24 V Connect via Control manufacturers: ABB, AEG, Bälz, Centra, Con- spindle by universal spindle clamp. An
- + DC 24 V ! safety isolating
transformer
trolli, C.S.I., Danfoss, DIGI'Control, Elesta, GA, H.C.Sys-
tem, Honeywell, Inel, IWK, Johnson, Kieback & Peter,
antirotation device is supplied to prevent
unwanted rotation of the whole unit.
Y DC 0…10 V Landis & Staefa, Messner, Priva, RAM, R+S, Samson,
Satchwell, Sauter, SE-Electronic, Siemens, TA, Trend.
Steplessly adjustable angle of rotation
Measuring voltage U for position indicating or by integral potentiometer. Range match-
U DC 2…10 V
as master-slave control signal. ing of the working range and measuring
signal U is performed automatically by
% of set angle Reversing Reversing
switch L switch R the actuator.
100 Y=0 Y=0
Open Open
Manual operation by self-resetting push-
1 2 3 5
button when necessary (the gearing is
disengaged while the pushbutton is held
50 Closed Closed depressed).
T ~ Y U LM24-SR anticlock- clockwise- High functional reliability
- + wise-closing
damper
closing
damper The actuator is overload-proof, needs no
Parallel connection of several 0 Y
actuators is possible. Power 0 2 5 10 [ V ] limit switches and halts automatically at
consumption must be observed.
the end stops.
Electrical accessories (see Doc. 2.Z-.)
Technical data LM24-SR
SG..24 Positioners
Maintenance maintenance-free
22.1 94.1
Weight 620 g
8
BC Mounting instructions for LM24-SR
m0006707
m
in
2
.3
5
m
m
3
6...16
1 1 2
5...6Nm
2 3
100%
1
20%
3 4 5
m0007707
ENG-93001-93221-05.02-2M · Printed in Switzerland · ZSD · Subject to technical changes
m
in
.3
5
2
m
m
6...16
1
1 2
5...6Nm
2 3
100%
1
20%
3 4 5
9
LM24-SR Control and monitoring functions BC
Remote control 0...100% Minimum position
w0232205
Connect via Connect via
AC 24 V safety isolating AC 24 V safety isolating
T ~ ! transformer
T ~ ! transformer
1 2 3 5 1 2 3 5
T ~ T ~ 0V
Y U LM24-SR Y U LM24-SR 0% 100%
- + - + Angle of rotation
Reversing Reversing
a b switch L switch R
1 2 3 5
1 2 3 5
T ~
Y U LM24-SR
- + control mode T ~
Y U LM24-SR
Parallel connecting of further actuators is
possible. Note power consumption data. - +
to next actuator
1 2 3 5 1 2 3 5
T ~ T ~
Y U LM24-SR Master Y U LM24-SR Slave
- + actuator - + actuator
Function monitoring
T ~ AC 24 V Connect via Procedure
safety isolating
!
- + DC 24 V transformer AC 24 V at terminals 1 and 2
Disconnect terminal 3:
– For direction of rotation "L":
actuator runs
10
BC
11
BC
Standard actuators and Safety actuators for VAV systems for indi- Mixing actuators and Globe valves and intelli-
spring-return actuators motorizing fire and vidual room air control motorized ball valves gent linear actuators –
for air control dampers smoke extraction for HVAC water circuits also for leading makes
in HVAC systems dampers of valve