Escolar Documentos
Profissional Documentos
Cultura Documentos
c
The cold working on thread roots of the Drill Collars thru inducing compressive
stresses with the help of externally loaded roller will increase life of Drill Collar by
protecting against bending stress in fatigue.
/ Hard Banding at other locations are also catered upon request.
c ,
For Elevator and Slip (as per API-7G). It is possible to add elevator and slip recess to
,
Drill Collar. These recesses allow one to dispense with lift subs and safety
clamps and to attain savings in operating time. Recommended Slip & Elevator recess
dimensions are given below:
%
These non magnetic drill collars are of Cr-Mn type. The Chemical Composition will be
such so as to satisfy the following mechanical properties and permeability.
%
1
( %&%
2 3
'(
(
3.1/2" Thru 110,000 psi 120,000 psi min. 40
18
6.7/8" (758N/mm2) (827N/mm2) Ft lb.
100,000 psi 110,000 psi min. 40
7" Thru 11" 20
(689N/mm2) (758N/mm2) Ft lb.
*&
Relative Magnetic permeability shall be less than 1.010 through the entire length and
the level of such permeability to be uniform. This level of permeability to be uniform.
This level of permeability remains stable despite fluctuation of local plastic
deformation and temperature fluctuation during operation.
1
Size conform to API Spec.7.
Austenic stainless steel drill collars are subject to cracking due to conjoint action of
tensile stress and certain specific corrodents. This is called stress corrosion cracking.
$
,&5c %
$
,&5c %
+ ,
6
)
(
- ,
long stress relief grooves on box ends are standard on 4 1/2" IF, 4" IF & 3 1/2 IF
Connections.
- API stress relief grooves on pin ends are standard on 4 1/2" IF, 4"IF & 3 1/2 IF connections.
- Thread roots are cold worked on all sizes.
- All connections are phoshatized, coated with lubricant and provided with steel protectors.
$ *
To optimize wear resistance hardbanding is standard on pin and box connections and central upset.
The heavy duty hard metal is sintered granular tungsten carbide 10/20 mesh or 20/45 mesh(fine
particles). The hardbanding is deposited by an automatic machine after pre-heating the pipe and is
followed by stress relieving. Standard pads
- One 4" wear pad on both pin and box end. Plus one 1" pad on taper section of box.
- Two 3" wear pads on central upsets.
The hardbanding is completely flush on both tool joints and 4/32" oversize on the central upset
(fully flush on request).
- Nominal Size
- Range
- API stress relief grooves, if needed
- Internal Coating, if needed.
8 9##c
!9$9c!
$9c!
* 4c
: 4#
" ;;
< #c
= 9!
> c9
?
@ 4c
82
!9
c
88 $9c!
c
8 #99c
8 #9!9
8*
,
exclusively manufactures Inside Blowout Preventer in India.
A &
7(
A
&
$
.A
&
,
exclusively manufactures Kelly in India
A
&-
A
&-
c
%
1. Spring
2. Lower Seat
3. Lower Seat O-Ring
4. Operating Stem
5. Stem O-Ring
6. Ball
7. Lower Split Retainer Ring
8. Upper Seat
9. Upper Seat O-Ring
10. Upper Split Retainer Ring
11. Solid Retainer Ring
12. Snap Ring
13. Body
&
*1
#
*1
,
*1
,
&%
*1
/
This stabilizer has been designed with a field replaceable sleeve. This sleeve is
screwed into a one-piece body and can easily be made up by using rotary tongs.
The fishing neck and sleeve mandrels are available with the same end connection as
drill collars.
Sleeves are designed with tungsten carbide hard faced surface (Type-A) or with
pressed in tungsten carbide buttons (Type-B). Both types are available at customer's
request. The worn hard facing can be repaired at ,
0 shop.
(
1. Hole Size.
2. Drill Collar O.D.
3. Size & Type of upper and lower connections.
4. Mandrel Size (D or E).
5. Mandrel Bore (G).
6. Type of Sleeve (A or B).
7. Cast Steel or Pressed steel thread protectors.
c %
(%C
+ /
To order or request quotations on ,
c %
(%C please specify:-
- Nominal Size.
- Bore Diameter.
- Tool Joint O.D.
- Size and type of connections (Example: 4 1/2"I.F. box up X 4 1/2" I.F. pin down,
etc.)
- Overall lebgth, shoulder to shoulder.
- 18 degree taper or square shoulder.
- Pressed or cast steel thread protectors.
/ Stress relief groove as per API-7 can also be provided on request.
,
exclusively manufactures Thread Protectors, Lift Plugs & Lift Subs in India.
C
C
) c
+++
%
+
9D>
%
$
%&D'
%
8B2B222 8B"2B222 8:3 ?<#$ "2)D!#
$
/