Escolar Documentos
Profissional Documentos
Cultura Documentos
Submitted By
Tallat Masood (9574)
Supervised By
Mr. Farhan Sohail
Chapter# 1
Introduction
Free space optical communication is used to transmit data between two stations. Free
space optical communication is the part of technologies used in telecommunication and
referred as the line of sight communication which transmits a modulated beam of light in
free space.
Light emitting diode (LED) or Laser diode is used in free space optics. Beam energy in
free space optics is collimated and transmitted via free space compared to the optical
cables in which beam is guided.
• There are less chances of light being distorted outside the atmosphere that is why
it is used for communication between spacecrafts.
• For short distance optical communication, LEDs are used and infrared laser lights
are used for long distance communications.
• Distance and data rate of free space optical communication are highly dependent
on atmospheric conditions.
1.1.1.1 Applications:
1.1.1.2 Advantages:
• Transparent protocol.
• Light beam may be visible or invisible to provide help for aiming and detection of
failures. [1]
1.2 Laser:
Many different types of media are used for communication purposes. But compared to
other types of media, laser has unique characteristics as a communication media. Line of
sight laser communication can be used when it is hard for wires to be physically
connected with a remote location. There is also no need of laser light shielding for long
distances which is main requirement for cables. Longer distance communication is
possible with the use of laser. It is also possible to make communication possible by using
RF but it may face interference due to other RF transmitters. As diameter of laser is few
millimetres and also it is line of sight technology, it is harder to tap the data. Due to it’s
this characteristic it makes communication safe and secure.
There are three main characteristics of laser light, which are described in the coming
sections.
1.2.2.1 Coherent:
Two waves travelling can add up to give larger wave or can be subtracted from one
another to give shorter waves. It all depends on the relative phase of the waves. If two
waves have constant relative phase, they are said to be coherent. Similarly laser exhibits
this property.
1.2.2.2 Monochromatic:
Laser light has one wavelength which has its origin in stimulated emission from one set
of atomic energy levels. So the laser light has single colour and is monochromatic.
1.2.2.3 Collimated:
Laser light bounces back many times between the reflecting mirrors of laser cavity. It
results in narrowing the beams and light do not spread very much.
Due to wavelength and maximum output power, lasers have been classified into four
classes. This classification categorises the lasers according to their ability to damage
human eye. Classification of laser is dependent on the concept of accessible emission
limit (AEL) that defines each laser class. This is normally maximum power and energy
that can be emitted about a specific range of wavelengths and time of exposure.
1.2.3.1 Class 1:
Laser of this class is safe one to use under estimated conditions of operation. Safety under
every condition is not guaranteed.
1.2.3.2 Class 2:
Class 2 lasers have output light in the visible spectrum, which starts from 400 nm and
ends at 700 nm. It is assumed that the blink reflex will close the eyes within fraction of a
second and it is necessary to provide protection. Long-standing exposure of this class
results in damage.
Class 3 lasers are safe when viewed by the unaided eye but when viewed by the
instruments, result may be unsafe.
This class of laser is safe for reflected light but direct viewing of light is hazardous. It is
directed to users that not use instruments for viewing.
1.2.3.5 Class 4:
Laser of this class are horribly dangerous. Its direct beam causes fire and skin injury. It is
avoided for communication uses. [2]
Our aim was to design and implement free space laser communication system by dividing
it into two sections of transmitter and receiver. Main aim of the project was to transmit
analog and digital data simultaneously using the same laser beam that is also bandwidth
efficient. As bandwidth of the laser can be described in frequency so if a laser for
example has a wavelength of 532 nm it corresponds to frequency of 5.6×1014 Hz by using
following formula.
λ= C/F
Frequency of 5.6×1014 Hz is the bandwidth of a laser whose wavelength is 532 nm. So it
follows that use of laser for simultaneous transmission of voice and text results in
efficient bandwidth utilization. Diagram shown in the next page is of the proposed
communication system.
It shows that we wanted to transmit voice and pc to pc text through same laser beam.
Hyper terminal was proposed to be used for text communication between two stations.
Working on this project required a comprehensive knowledge about the mixing of voice
and text signals and then separating them at the receiver side. As project working was
divided into two tasks, there was need to first design block diagrams of these two
sections.
1.4.1 Transmitter:
National university of modern languages, Islamabad 7
Free space laser communication system
We studied about different methods such as optical wavelength division multiplexing and
frequency division multiplexing to multiplex analog and digital signals but these methods
required components which were not suited to budget constraints. So we presented a way
to mix both signals which was according to the budget constraints. Block diagram
designed for project represented the way of mixing both signals which is given below.
1.4.2 Receiver:
At the receiver side, aim was to detect the mixed signal and separate both of voice and
text signals. It was proposed to use a separator to separate voice and text signals.
Phototransistor was proposed to be used to detect laser beam. Block diagram better
defines the use of separator which is given below.
Main components used in the receiver are Transformer, Bridge rectifier, Voltage
regulator, Audio amplifier, Max-232, DB-9 connector, Phototransistor and Earphone.
Hyper terminal is the window’s application which enables to transfer text and files from
one PC to a remote PC. Hyper terminal supports two type of connections for text and file
National university of modern languages, Islamabad 9
Free space laser communication system
transfer, these are by using a modem and Ethernet connections. It is an easy to use tool of
windows.
PCB wizard was used in the transmitter and receiver designing of the system. PCB wizard
has the complete component library. Values of the components can be changed
accordingly. We simply selected the components needed, dragged them into the working
sheet and connected them.
Chapter# 2
Project work
2.1 Phases:
For our simplicity and manageability, we divided the project into different phases. The
Gantt chart is made to schedule project. Chart represents milestones to be achieved by
following the schedule.
• Component study
• Hardware design
This was the phase in which we discussed areas of interest and planned project. This was
the major part as whole degree was dependent on the selection of the area of project. It
was kept in mind that all the group members are agree and willing for this project.
Keeping in mind the planned project, we gathered knowledge about different technologies
and very much related to the project
In this phase, we studied about the different components used in the project which were
mentioned in the block diagrams.
Laser diode used in the system had to transmit voice and text data simultaneously.
Thus it is clear that a laser consists of an amplifying medium and a set of mirrors to feed
the light back into the amplifier for continued growth of the developing beam.[3]
Production of laser light can be better described by the following diagram.
Laser diode used in the system was a class 2 laser which was safe one to use. Pin diagram
of the laser diode is given below.
• Optical output: 5 mW
• Wavelength: 650 nm
• Threshold current: 70 mA
• Operating current: 85 mA
2.3.2 Microphone:
Microphone was used to take audio input from the user. It converts voice into an
electrical signal. For this purpose we used Electric Condenser microphone. Power
requirement of condenser microphones is fulfilled by providing power from a battery or
external source. These microphones are also more sensitive and responsive. [6]
Condenser microphone works like a capacitor. As capacitor has two plates, condenser
microphone also has two plates. One of these plates is very thin and its action is as a
diaphragm. When sound signal is received, diaphragm vibrates resulting in changing the
distance between the two plates and also resulting in change of capacitance. Capacitance
increases and current occurs when plates are closer. When plates are farther apart, there
happens a decrease in capacitance and a discharge current occurs.
2.3.3 Transistor:
Transistor is constructed with three semiconductor doped regions, which are separated by
two PN junctions. Transistor that we used in our project is C1815, which is an NPN
transistor. There are three regions in a transistor, which are Base, Emitter and Collector.
Pin diagram of transistor used in our project, is as below:
The DC current gain is defined by β dc which is equal to the ratio of collector current to
the base current. The collector current is much greater than base current that is why it
exhibits DC current gain. [7]
2.3.4 Transformer:
National university of modern languages, Islamabad 16
Free space laser communication system
Transformers are characterised into two types i.e. step down transformer and step up
transformer. Transformer used in this project is the step down transformer. This
transformer was used to convert 220v AC supply into 9V AC. It provided main power
supply for transmitter unit. We attached a bridge rectifier with the transformer to convert
AC into DC and that reverse polarity may not affect the remaining circuitry. Diagram
given is of step down transformer, which is used in transmitter unit.
Transformer uses two coils which are coupled together, one coil is called primary coil and
other is called secondary coil. Transformer transfers electrical energy from primary coil
to secondary coil due to the mutual induction. If we connect load with the secondary coil
then varying current in primary coil will produce electrical energy in secondary coil i.e.
load.
Leo Graetz was the inventor of bridge rectifier. Bridge rectifier is basically a diode bridge
circuit. Main feature of bridge rectifier is that the output polarity remains the same
ignoring the polarity at the input.
Usually bridge rectifier is connected with the secondary coil of the transformer. During
positive half cycle, diodes D2 and D4 act as forward bias and conduct current from high
potential to low potential. D1 and D3 are reversed bias. In negative half cycle diodes D1
and D3 act as forward bias and conduct current, while D2 and D3 are reversed bias.
So it is clear that a bridge rectifier follows two voltage cycles that are positive half cycle
and negative half cycle. In positive half cycle load voltage is positive while in negative
half cycle load voltage is negative.
2.3.5.2 Smoothing:
Usually a capacitor is attached with the output of the bridge rectifier, especially in
situations where its task is to convert AC into DC. The capacitor used is called the
smoothing capacitor whose purpose is make variations less in the rectified AC output
voltage waveform from the bridge rectifier. [9]
The L-7805 is a simple voltage regulator which has 3 pins. Its function is to take 9v and
produce a constant 5v at the output. Its input is 9v of bridge rectifier. Its purpose of use is
to provide constant power supply of 5v to those components whose operating voltage is
5v. Below is the diagram of voltage regulator.
Audio amplifier of this type is usually used in low voltage applications. Minimum voltage
required for its operation is 4 volt. Pin diagram of the audio amplifier is given at the next
page.
Gain of 20 is set internally but it can be increased by putting a capacitor between the
pin#1 and pin#8. LM-386N only amplifies voice signal because it only allows frequency
band of less than 4 kHz to pass at its input.
2.3.8 Max-232:
This IC is very much of interest for people who want to build their own electronic devices
and want to interface them with RS-232. Its purpose of use is to convert CMOS or TTL
logic levels into RS-232 and vice versa.
Digital devices in our daily use require either CMOS or TTL logic levels. Therefore the
first step of connecting these devices to the RS-232 port is to convert the RS-232 logic
levels back into 0 and 5 volts logic. This IC is low power driver and receiver, which
requires only +5v for its operation.
At the transmitter side this IC is used to drive CMOS/TTL and RS-232 input. Both driver
inputs are added to give one output. And at the receiver side, CMOS/TTL logic is
converted into RS-232 logic. Logic conversion function of Max-232 can defined with the
help of following table.
Max-232 is dual transmitter/receiver IC. Pin diagram of Max-232 is given at the next
page.
In parallel port communication, 8 bit data is sent and received at a time over 8 separate
cables. This makes data transfer very quickly. While in serial port data transmission and
reception happens as one bit at a time over one wire. So by this way it takes 8 times more
than parallel cable for one byte. Serial port communication is used for long distance
communication.
Serial port standard is called the EIA/TIA-232-E standard. It is the Interface between
Data Terminal Equipment (DTE) and Data Circuit-Termination Equipment (DCE)
facilitating Serial Binary Data Interchange. RS-232 standard is apprehensive with serial
communication between a host (DTE) and a peripheral system (DCE). [12]
• Valid signals are plus or minus 3 to 15. Positive is logic zero and minus is logic 1.
DB-9 connector is characterised into two categories, which are: 1) Male and 2) Female
connector. DB-9 male connector has pins in it which are inserted in female connector.
DB-9 male connector Diagram is given below.
DB-9 female connector has holes in it in which pins of male connector are inserted.
Diagram of DB-9 female connector is given below.
There are 9-pins in a DB-9 connector. Their functions are defined in the following table.
Pin# Function
2.3.10 Phototransistor:
compared to the photo diode. It is also possible to use a photo diode and then amplify its
output by using an external amplifier. But this technique is even not practical and cost
effective than phototransistors. The phototransistor can be viewed as a photo diode whose
output photo current is fed into the base of a conventional small signal transistor. [14]
Phototransistor used in our project is NPN phototransistor, whose part number is 55c
qt804 and its pin diagram is as follows.
Phototransistor used in our project receives laser light of 650 nm through the base region
and produces corresponding electrical signal, which is taken out from the collector region.
There are following three main reasons which inspired us to use phototransistors instead
of the photo diodes. [14]
• Responsivity: Phototransistors are highly sensitive due to the lower response time
than photo diode. Response time of 55c qt804 is 50ns.
• Dark current: There is always some amount of current flows through the
phototransistor even when no current is detected; this is called the dark current.
Amount of dark current for 55c qt804 is less than or equal to the 10nA.
After the selection of project and related component study, we worked on the hardware of
the project. We made analysis of the project from different aspects. First we worked on
the designing of the circuit diagram. Then after it we assembled all the components
according to the circuit diagram.
Transmitter description can be justified by dividing the circuit diagram into its major
parts. These major parts and their relationships are described below.
• Voltage regulator: It was used to take 9v Dc input from the bridge rectifier and
convert it into 5v DC. Reason to convert 9v into 5v was that some components
required 5v for their operation.
• Audio power amplifier: Audio power amplifier was used to amplify voice
signals received from the transistor output. Amplified voice signal was then fed to
max-232 to convert voice signal into serial supported voice signal. Audio
amplifier section diagram is given at the next page.
• Serial supported voice and data transmission: Data input and amplified voice
signal was taken by max-232. By this way voice became serially supported and
serial supported voice and data signal was then transmitted through laser diode.
Complete circuit diagram designed in PCB wizard is given at the next page.
Light signal transmitted by the transmitter carried the voice and data information. It was
detected by the phototransistor, which produced electrical signal. This electrical signal
was amplified using the same pre-amplifier configuration. Configuration and function of
transformer, bridge rectifier, voltage regulator and audio power amplifier was the same.
Output of audio amplifier was fed into audio jack which produced voice at the output
while data was received by max-232, whose logic level was of CMOS. So its logic level
was converted into RS-232 logic level. Data output was then sensed by serial port through
the use of hyper terminal.
The receiver diagram is given below, which shows all the components and their
connection.
When hardware was assembled then there was a need to configure hyper terminal for the
first time use. Configuration of hyper terminal is easy and can be done in limited number
of steps. Below is the descriptive information about how we configured hyper terminal.
2. After cancelling the location information window, there appeared phone and
modem options window. Then we clicked on OK.
4. When we were finished with the selection of connection name and icon, there
opened another window from which we selected the port number of serial port e.g.
com1 or com2.
5. There opened window of serial port’s properties. We selected the data rate from
this window.
6. After we have completed the procedures discussed above, there opened a blank
window of hyper terminal. We clicked in the File tab and selected the properties
icon.
7. There opened connection properties window, we clicked on the setting tab of the
window and selected ASCII setup option.
8. In ASCII setup, we simply checked on all the boxes and clicked on OK.
9. These were all the steps that we performed while configuring the hyper terminal.
At the last we were able to write on the hyper terminal’s window that was
transmitted to the other computer.
Chapter# 3
Results
3.1 Result:
Proper planning at the beginning of project resulted in the completion of project before
the deadline. Voice and text data communication through this system was very reliable
and efficient. Resulted security system is better capable of to be implemented for
communication where there is need to jam RF frequencies.
• Transmitter: Below given diagram is of the transmitter used for free space laser
communication system. The figure contains complete and practical view of the
transmitter. Every component used in the circuit e.g. condenser microphone,
transistors, voltage regulator, transformer, audio amplifier, Max-232, DB-9
connector and laser etc. is shown in the below given figure.
• Receiver: Next snapshot is of the receiver used for free space laser
communication system. Figure is complete and practical view of the receiver. It
shows each and every component used in the project e.g. phototransistor, variable
resistor, transformer, voltage regulator, audio amplifier, Max-232 and ear-phone
pin etc.
Chapter# 4
Conclusion and scope of the project
Free space laser communication system has much more applications in connecting two
building, in airports, in defense and sensitive areas etc.
In the future free space laser communication system can be enhanced by including the
functions of self alignment of laser beam and range enhancement. Communication range
can be increased by the use of high power infrared laser, so that it may provide more
enhanced security for communication. Self alignment of laser beam may be achieved by
using a separate laser beam with the combination of a servo motor.
Features of free space communication system are summarized in the following steps.
Free space laser communication system is a trustworthy system but it only has one
limitation due to low power laser diode.
4.4 Conclusion:
Free space laser communication system paved the way for us to learn about free space
optics, Laser physics, its use for communication and optical multiplexing techniques.
Project was helpful to understand the use of hyper terminal for communication purposes.
System designing helped to learn PCB wizard.
[2]. Introduction to fiber optics by john crisp, 2nd edition. ISBN: 07506 50303
[4]. www.scribd.com
[5]. www.mi-lasers.com
[6]. www.mediacollege.com
[7]. www.forum.arcadecontrols.com
[8]. www.qy6.net/upimg/prodimg/base/12053.jpg
[9]. www.images.blog-u.net/img/diodes-bridge-rectifier/
[10]. www.freedatasheets.com/blog/labels/datasheet.html
[11]. www.focus.ti.com
[12]. www.navtechgps.com
[13]. www.lammertbies.nl
[14]. www.sunrom.com/sensors/light-infrared/phototransistor
[15]. www.electricalwhat.com
Appendix A
Datasheet
Datasheet
Datasheet
Datasheet
National university of modern languages, Islamabad 50
Free space laser communication system